Search

The study aims to present the results of paper compression under an axial load. Different heights of samples subjected to compression were taken into account. The main goal of the analysis was to determine experimentally the maximum compression load. In addition, numerical models based on the finite element method (FEM) were validated to refer to empirical results. The performed numerical simulations were founded on Green–Lagrangian nonlinear equations for large displacements and strains. The progressive failure of the compressed orthotropic material after exceeding maximum stresses was based on Hill's anisotropy theory. Nonlinear calculations were conducted by using a typical Newton–Raphson algorithm for achieving a sequence convergence. The accuracy of the developed model was confirmed experimentally in compression tests. The technique of analysing the shape of the compressed paper sample on the basis of images recorded during the measurement was used. The obtained test results are directly applicable in practice, especially in the calculation of the mechanical properties of corrugated cardboard and in determining the load capacity of cardboard packaging. Knowing the maximum compressive stress that packaging paper can withstand allows packaging to be properly designed and its strength assessed in the context of the transport and storage of goods. [ABSTRACT FROM AUTHOR]

• The specific collapse behavior of the circular paper tube under axial impact. • A simplified collapse mechanism for the collapse mode of circular paper tube. • A theoretical model to predict the mean crushing force of circular paper tubes. • Axial quasi-static compression and dynamic impact tests of circular paper tubes. • The theoretical results give an excellent agreement with the test results. In this paper, the deformation mechanism and energy absorption characteristics of circular paper tube under axial quasi-static and dynamic loadings are studied. The collapse mode of circular paper tube is obtained, which is different from the collapse mode of metal tube. Based on the collapse mode, a simplified spiral multi-lobe folding mode of circular paper tube is proposed, and a theoretical prediction model of energy absorption performance of circular paper tube under axial compression and impact is established, considering the effects of effective crushing distance and strain rate dependence. The theoretical results are in good agreement with the results of quasi-static compression and dynamic impact tests of circular paper tubes. The proposed model can be used to evaluate the characteristics of energy absorption structures in practical applications, and provide theoretical guidance for optimal design of paper tube structures according to the energy absorption requirements. [ABSTRACT FROM AUTHOR]

The current researches on soil-pile interaction under combined action of axial and lateral loads are mainly focused on the short or middle-long piles in a homogeneous soil. The practice for design of piles subjected to both axial and lateral loads commonly considers the two loads separately. In this paper, a super-long pile group in stratified soils under both vertical and lateral loads and the pile-soil interaction with the pile cap in contact with ground are all simulated together by a three-dimensional nonlinear numerical model. The influence of lateral loading on the vertical pile stresses and bending moments is analyzed. In addition, the effect of vertical loading on the lateral pile response is also investigated. On the other hand, given the fact that the super-long pile group is relatively insufficient in resisting a large lateral load, the pile in shallow depth is sleeved to reduce the horizontal displacement. Using the sleeve, the lateral load is transferred onto the deeper soil mass. The results show that the sleeved super-long pile group proposed in this paper can reduce the horizontal displacement significantly and is feasible in practical applications. [ABSTRACT FROM AUTHOR]

The second generation (2G) high-temperature superconducting (HTS) REBCO tape and the HTS cable made by the REBCO company are considered to be alternative materials for future superconducting magnet design due to their exceptional performance. The twisted stacked-tape slotted-core (TSSC) cable-in-conduit-conductor cable, which is one of the crucial layout structures in HTS cables, has been extensively studied by numerous research groups over the years. In this paper, a 3D finite element model of the TSSC HTS cable under bending and axial tensile loads is established using the bilinear isotropic hardening model in COMSOL commercial finite element software. The mechanical behavior of the TSSC cable under bending and axial tensile loads, as well as the evolution process of overall cable performance and critical current of individual tapes inside slots, are revealed by conducting mechanical analysis and using an empirical fitting formula between the critical current density of the 2G HTS tapes and axial strain. Furthermore, optimization engineering suggestions for its structure are provided, such as reducing the twist pitch, decreasing the tape width, increasing the number of tapes, reducing the slot width while avoiding direct contact between tapes and slot walls, increasing the number of slots, increasing diameter of diversion trench and inner diameter of helical core under predominant bending loads. In the case of axial tensile loads, the aforementioned suggestions are also applicable except for the inner and outer diameters of the helical core. The critical current performance can be enhanced by augmenting the outer diameter of the helical core in this case. However, it is almost unaffected by the inner diameter of the helical core. [ABSTRACT FROM AUTHOR]

The loading capacity in the axial direction of a bolted thin steel plate was investigated. A refined numerical model of bolt was first constructed and then validated using existing experiment results. Parametrical analysis was performed to reveal the influences of geometric parameters, including the effective depth of the cap nut, the yield strength of the steel plate, the preload of the bolt, and shear force, on the ultimate loading capacity. Then, an analytical method was proposed to predict the ultimate load of the bolted thin steel plate. Results derived using the numerical and analytical methods were compared and the results indicated that the analytical method can accurately predict the pull-through capacity of bolted thin steel plates. The work reported in this paper can provide a simplified calculation method for the loading capacity in the axial direction of a bolt. [ABSTRACT FROM AUTHOR]

This paper investigates the collapse behavior of square paper tubes and the influence of tensile-compressive yield asymmetries of paper tube materials by combining the theoretical and experimental methods. An approximate energy absorption theoretical model is developed to predict the mean crushing force of square paper tubes subjected to axial loading. Besides, combined with the remarkable linear regularity of the experimental results, the numerical curve of the effective crushing distance ratio of paper tubes is obtained to improve the applicability of the proposed model. Then the theoretical results taking account of effective crushing distance are in excellent agreement with the experimental results. The proposed model can be used not only for the prediction of energy absorption characteristics of paper tubes in a logistics environment, but also to guide the protective packaging structure design with paper tubes. • The collapse behavior of square paper tubes under quasi-static compression is studied. • The influence of tensile-compressive yield asymmetries of paper tube materials. • A theoretical model is proposed to predict the mean crushing force of paper tubes. • An effective crushing distance curve is obtained to improve the model accuracy. • The theoretical predictions are in good agreement with experimental results. [ABSTRACT FROM AUTHOR]

The role of steel connections is essential in structural fire design and analysis for steel-framed composite structures. The current structural design provisions provide strength reduction factors of load-carrying members and their end-connection elements at elevated temperatures, based on small-scale experiments under uniform heating conditions. The realistic thermal and structural evolution in member connections, especially as part of full-scale floor assemblies exposed to a large compartment fire, has not been well characterized. A large compartment fire experiment was recently conducted on a 9.1 m by 6.1 m composite floor assembly as part of a two-story steel-framed building. The test assembly had a total of ten shear-tab (fin-plate) connections subjected to combined fire and mechanical loading. This paper presents the measured thermal response of these connections to fire and comparison with the corresponding Eurocode 3 predictions with two methods (1) incorporating the beam bottom flange temperature at midspan and (2) the section factor method. The results show that the Eurocode 3 methods conservatively predict the maximum temperature during heating and the cooling rate but overestimate the high-temperature strength of connections when estimated using the section factor method, showing that the Eurocode 3 simplified approaches are not meant to provide the details of the failure mode for connections. This study suggests that estimating the strength of connections using strength reduction factors may not guarantee a safe structural fire design. In addition, this paper estimated the total axial force (from slab and beam) at the composite connection via using the strain gauge measurements close to the column bases which were not exposed to fire. It suggests realistic axial load and rotational demand on the shear connection due to restraints to thermal elongation or contraction of supported members should be considered in future design guidance as should designing and detailing the connections for ductility to withstand the inelastic deformation demands during the heating and the cooling phases. [ABSTRACT FROM AUTHOR]

This paper proposes a review of the previous research work and the representative publications regarding the seismic behavior of the concrete-encased steel (CES) columns. Concrete-encased steel sections are composed of steel sections encased in reinforced concrete members. The research work recently showed increased attention to this type of column due to its advantages compared to conventional reinforced concrete columns. Firstly, the analytical studies of the behavior of the CES columns under axial loads, including comparative studies between different research works, are presented. Then, the behavior of the CES columns under combined axial and flexural loads is also highlighted. An overview of the analytical confinement material models is addressed. In addition, the discussion and summary of the seismic behavior of the CES columns and the important parameters affecting the seismic behavior of these types of columns are included. Although important progress has been made by the previous studies in the CES columns under the axial load and the combination of axial and seismic loads, they fundamentally focused on the building columns, and little attention was paid to the impact of lateral reinforcement and their configuration in bridge piers. Due to the lack of studies on the parameters affecting the seismic behavior of the bridges, more studies should still be made to better understand the behavior of the CES bridge piers. This paper provides a reference for the research and engineering practice of concrete-encased steel bridge piers. It also concludes with suggestions for future studies to integrate the seismic requirement of the CES bridge piers in Canada. [ABSTRACT FROM AUTHOR]

This paper delves into the impact of the damage accumulation effect, which leads to the degradation of material strength and stiffness, on the seismic resistance of transmission towers. Building upon the elastic–plastic finite element theory, a mixed hardening constitutive model is derived for circular steel tubes, standard elements in transmission towers, incorporating the damage accumulation effect. A user material subroutine, UMAT, is created within the LS–DYNA framework. The program's validity and reliability are established through axial constant–amplitude loading tests on single steel tubes. The subroutine is employed to conduct the incremental dynamic analysis (IDA) of an individual transmission tower and to contrast it with the structure utilizing the Plastic Kinematic material model, assessing the discrepancies in tower top displacements and segment damage indices (SDIs) at both macroscopic and microscopic scales. The results shows that the Plastic Kinematic model inflates the seismic performance of the transmission tower. When considering the damage accumulation effect in structural failure, the damage index of the members increases, leading to a reduction in both the structural strength and stiffness. The dynamic response in the plastic phase becomes more pronounced, and the onset of structural failure is accelerated. Consequently, structural analysis under seismic conditions should account for the damage accumulation process. Through the delineation of member and segment damage, the extent of damage to transmission tower segments can be quantitatively assessed. Subsequently, the ultimate load–bearing capacity and the most vulnerable location of the transmission tower can be ascertained. Finally, this paper provides a detailed analysis of the transmission tower collapse process under seismic action and summarizes the mechanism of collapse for the structure. [ABSTRACT FROM AUTHOR]

Origami structures, which were inspired by traditional paper folding arts, have been applied for engineering problems for the last two decades. Origami-based thin-wall tubes have been extensively investigated under axial loadings. However, less has been done with radial stiffness as one of the critical mechanical properties of a tubular structure working under lateral loadings. In this study, the radial stiffness of novel thin-wall tubular structures based on origami patterns have been studied with compression tests and finite element analysis (FEA) simulations. The results show that the radial stiffness of an origami-inspired tube can achieve about 27.1 times that of a circular tube with the same circumcircle diameter (100 mm), height (60 mm), and wall thickness (2 mm). Yoshimura, Kresling, and modified Yoshimura patterns are selected as the basic frames, upon which the influences of different design parameters are tested and discussed. Given that the weight can vary due to different designs, the stiffness-to-weight ratio is also calculated. The origami-inspired tubular structures with superior stiffness performances are obtained and can be extended to crashworthy structures, functional structures, and stiffness enhancement with low structural weight. [ABSTRACT FROM AUTHOR]

Planetary Threaded Roller Bearing (PTRB) is a new bearing suitable for the heavy load linear drive mechanism. The load is transferred internally through annular threads, affecting the bearing capacity of the thread's contact load distribution characteristics. The structure of PTRB is discretized to study the contact load distribution of PTRB. The axial stiffness of the thread's teeth, its axial stiffness, and the contact stiffness of contact points are calculated. Moreover, a 1D equivalent spring network model is proposed based on discretized structure and stiffness. The PTRB contact load calculation model is proposed using the direct stiffness method and a 1D equivalent spring network model. Finally, the accuracy of the model proposed in this paper for calculating the contact load distribution of threaded teeth is verified by comparing the results obtained from theoretical model calculations, finite element methods, and experiments. The theoretical model proposed in this paper can provide theoretical guidance for PTRB parameters. [ABSTRACT FROM AUTHOR]

Traditional aero-engine bearings rotate simultaneously with their inner and outer rings, which makes the temperature rise prediction model computationally large with low accuracy, and it cannot be accurately verified due to the means of testing. This paper presents a method for predicting the temperature rise characteristics of aero-engine bearings under composite load conditions. Firstly, the local method is used to calculate the heat generation from heat sources such as bearing spin, lubricant drag, and the differential sliding of steel ball and collar, respectively, then finite element modelling and steady-state thermal analysis are carried out for aero-engine bearings under the simultaneous action of axial and radial external loads, a double-rotor test setup is designed and the predictive model is validated, and finally, the influences of rotational speed and load on the temperature rise characteristics of the bearings are investigated. The study shows that the aero-engine bearing prediction model proposed in this paper has high accuracy; with the increase in the rotational speed of the inner ring of the bearing, the temperatures of both the inner and outer rings of the bearing increase significantly; the temperatures of the inner and outer rings of the bearing increase with the increase in the axial load, and the effect of the radial load on the temperature of the bearing is not obvious. [ABSTRACT FROM AUTHOR]

In the process of horizontal well construction, the working environment in the well is very complicated. It is difficult to determine the actual deformation and force of the coiled tubing in the wellbore from the load change at the wellhead along. In addition, the coiled tubing wrapped around the reel and entering the wellbore through the injection head may cause an initial residual bending. In this paper, the mathematical model of the coiled tubing under axial load during buckling deformation is established, and the analytical solution with the time term is derived by reasonable simplification of the model. The effect of residual bending on the post-sinusoidal buckling of the coiled tubing in the horizontal well was investigated using the separation variable method. The effect of residual bending variations on the well wall contact forces is analyzed. The research shows that the initial parameter Г is the main factor influencing the post-sinusoidal buckling of the coiled tubing with residual bending. The larger the parameter value Г, the greater the effect of the residual bending on the post-sinusoidal buckling deformation of the coiled tubing, and the earlier the critical point of the mixed sinusoidal-helical buckling of the coiled tubing appears. The compression velocity of the coiled tubing has a significant effect on the well wall contact force. The faster the compression, the greater the contact force. By introducing the time term and the separation variable, this paper provides a new method and theoretical basis for further study of the process of entering sinusoidal-helical buckling of the coiled tubing with initial residual bending. [ABSTRACT FROM AUTHOR]

The methods employed to calculate the axial bearing capacity of a helical pile depend on the shear failure model around the pile, which is also influenced by the spacing and diameter of the helical plates. However, studies on the transition of the failure mode and the load transfer mechanism with the change of helical plate spacing and diameter in cohesionless soil subjected to axial compressive load were limited. Thus, this paper investigated the effects of helix diameter and spacing on the axial compressive load-bearing capacity, shear failure model, and load transfer mechanism of helical piles with two helical plates embedded in the homogeneous medium and dense sands, as well as in the stratified medium to very dense sand. Axial loading tests on helical piles with various helix diameters and spacings were simulated using a two-dimensional finite element program with axisymmetric modeling to obtain the load-settlement curve, which was later used to estimate the ultimate bearing capacity of the helical piles. The ultimate bearing capacity of the helical piles was also computed using the conventional methods, i.e., the individual bearing and cylindrical shear methods, and then compared to the numerical-based axial bearing capacity. The stress-strain behaviors of pile and soil were modeled using the Linear Elastic and Mohr-Coulomb material models, respectively. The results show that the numerical-based ultimate bearing capacity of a helical pile increased with increasing the diameter and spacing of the helix. However, the ultimate bearing capacity computed using conventional methods did not show this trend. Then, the transition from the cylindrical shear to the individual bearing failure mechanism occurred at a spacing ratio (i.e., helical plate spacing divided by its diameter) of about two. Ultimately, the load transfer curves indicate that the helical plates mainly supported the applied load. [ABSTRACT FROM AUTHOR]

This paper presents an experimental and numerical investigation of RCC (Reinforced Concrete) piles with helical grooves under axial and lateral loads in cohesionless soil. A set of experiments is carried out to assess the performance of RCC piles with helical grooves. To replicate the experimental findings, the Finite Element Method (FEM) is employed using Abaqus software. Three-dimensional (3D) models are created to represent both the pile and the soil using Abaqus. The paper compares settlement characteristics and lateral displacement of plain RCC piles and RCC piles with helical grooves. This study also evaluates the impact of varying the pitch of helical grooves on enhancing pile performance. The results indicate that RCC piles with helical grooves outperform plain RCC piles in terms of both axial and lateral load-carrying capacity, inferred from both experimental and analytical techniques. [ABSTRACT FROM AUTHOR]

Chirality and porosity are characteristic properties of nanostructured materials. Their effects on the mechanical behaviour of structural elements, such as shells, plates and beams, cannot be disregarded. In this paper, we study the thermoelastic deformation of a chiral porous circular beam loaded with an axial force and torque. The beam is also under the action of a constant temperature field. The analytical solution is obtained using the results established in a paper recently published by the Author within the context of the strain gradient theory proposed by Papanicopolous. In the constitutive equations, the chirality is introduced by a material constant parameter and the porosity is described by means of a scalar function. Displacements, microdilatation function, and stress and strain fields are expressed in explicit form and in terms of engineering constants. Explicit formulas of the stiffness of chiral porous circular beams are presented and the effects of right and left chirality are discussed. [ABSTRACT FROM AUTHOR]

Purpose: Gas thrust foil bearings (GTFBs) are used to balance the axial load of engines. However, in some working conditions of large axial force, such as the use of single impeller air compressor, the load capacity of GTFBs is still insufficient. To solve this problem, the load capacity can be improved by increasing the stiffness of bump foil. The purpose of this paper is to explore a scheme to effectively improve the performance of thrust foil bearings. In the paper, the stiffness of bump foil is improved by increasing the thickness of bump foil and using double-layer bump foil. Design/methodology/approach: The foil deformation of GTFBs supported by three different types of bump foils, the relationship between friction power consumption and external force and the difference of limited load capacity were measured by experimental method. Findings: The variation of the foil deformation, bearing stiffness, friction power consumption with the external force at different speeds and limited load capacity are obtained. Based on experimental results, the selection scheme of bump foil thickness is obtained. Originality/value: This paper provides a feasible method for the performance optimization of GTFBs. [ABSTRACT FROM AUTHOR]

In this paper, the aim is to discuss the applicability of polyethylene terephthalate fiber-reinforced polymer (PET FRP) in DSTC structures. PET FRP can improve the strength and stability of structures by providing constraints for concrete. Herein, experimental and response surface analyses of the axial compressive properties of PET FRP–concrete–steel double-skin tubular stub columns (DSTCs) based on 26 DSTC specimens subjected to axial compression testing are presented. The height of each DSTC specimen is 600 mm, the outer diameter is between 305 and 315 mm, and the thickness of the added concrete is 43 mm. The main parameters are the number of layers on the PET FRP, the compressive strength of the concrete, and the thicknesses of the steel tubes. The experimental results show that the ultimate load and ultimate axial strain can be significantly increased by increasing the number of PET FRP layers, reaching 27.34% and 28.79%, respectively. When the compressive strength of the concrete increases from C30 to C40, the ultimate load and ultimate axial strain values of the DSTCs increase by 12.54% and 8.99%, respectively. In addition, as the thickness of the steel tube increases from 6 to 8 mm, the ultimate load and ultimate axial strain increase by 34.95% and 118.90%, respectively. These results indicate that the introduction of PET FRP significantly improves the overall performance of DSTCs. Increasing the number of PET FRP layers helps to limit the circumferential strain of DSTCs. P6-S8-C40 has the best ultimate load-bearing capacity and ultimate axial strain capacity, which reach 3356.18 kN and 0.1992, respectively. The main purpose of this paper is to study the influences of the PET FRP thickness (in different layers), steel tube thickness, and concrete strength on the properties, damage mode and damage process of DSTCs. [ABSTRACT FROM AUTHOR]

This paper aims to evaluate the seismic response of multitiered buckling-restrained braced frames (MT-BRBFs), assess the design provisions specified by the 2022 AISC Seismic Provisions for multitiered BRBFs, and propose improvements to these provisions. A set of 17 frames is first selected by varying bracing configuration, frame height, number of tiers, and tier height ratio. The frames are then designed in accordance with the 2010 and 2022 AISC Seismic Provisions. A numerical parametric study is performed under scaled ground motion accelerations. The results of the parametric study show that when the frames are designed to the 2010 provisions, the frame inelastic deformation tends to concentrate in the tier(s) undergoing tensile yielding due to their lower postyield stiffness, compared to BRBs yielding in compression, which creates unequal story shear, contributed by braces, in adjacent tiers with BRBs in tension and compression and engages column flexure to compensate for unbalanced brace story shears between tiers. Columns experience yielding and even buckling in several cases due to combined flexural and axial load demands. MT-BRBFs designed to the 2022 AISC Seismic Provisions exhibit a more uniform deformation response between tiers and relatively lower flexural demands in their columns. However, these provisions may overestimate column in-plane flexural demands (on the order of 3), resulting in potentially uneconomical design solutions. On the basis of the numerical simulations, modifications are proposed to compression BRBs' adjusted strength to better estimate column in-plane flexure and tier deformation while achieving an economical column design. The proposed improvements are validated using dynamic analyses. [ABSTRACT FROM AUTHOR]

The secondary air system of a gas turbine engine is a complex fluid network that is sensitive to geometric variations in the flow elements caused by manufacturing, assembly, and operating conditions. Geometric uncertainty of the flow elements is a major cause of secondary air system failure. To reduce the performance uncertainty due to geometric uncertainty, this paper constructs a probabilistic analysis method that couples the primary air system and the secondary air system and proposes a robust optimization mathematical model for the rotor axial bearing loads of the secondary air system, using the control of the rotor axial bearing loads as an example. A case study is presented to demonstrate the application of the proposed robust optimization method in controlling the scatter of axial bearing loads. Probabilistic analysis and sensitivity analysis are performed for the original design scheme and the robust optimization design scheme of the secondary air system. The results show that the standard deviation of the high-pressure axial bearing loads in the robust optimization design scheme is 72.9% lower than that in the original design scheme under the same uncertainty distribution of the labyrinth clearance. In addition, the sensitivity of the axial bearing loads to the labyrinth clearance is reduced. Thus, it is demonstrated that the proposed robust optimization method can effectively reduce the functional scatter and the sensitivity to geometric variations in the gas turbine secondary air system. [ABSTRACT FROM AUTHOR]

As the size of a layered structure scales down, the adhesive layer thickness correspondingly decreases from macro- to micro-scale. The influence of the material microstructure of the adhesive becomes more pronounced, and possible size effect phenomena can appear. This paper describes the mechanical behaviour of composites made of two solids, bonded together by a thin layer, in the framework of strain gradient and micropolar elasticity. The adhesive layer is assumed to have the same stiffness properties as the adherents. By means of the asymptotic methods, the contact laws are derived at order 0 and order 1. These conditions represent a formal generalization of the hard elastic interface conditions. A simple benchmark equilibrium problem (a three-layer composite micro-bar subjected to an axial load) is developed to numerically assess the asymptotic model. Size effects and non-local phenomena, owing to high strain concentrations at the edges, are highlighted. The example proves the efficiency of the proposed approach in designing micro-scale-layered devices. This article is part of the theme issue 'Non-smooth variational problems with applications in mechanics'. [ABSTRACT FROM AUTHOR]

This paper presents experimental results of combined cyclic load testing on a reinforced concrete (RC) column that was retrofitted with newly designed steel rods. The steel rods were installed around the column longitudinally and then anchored. The proposed steel rods utilize simple components and installation to enhance both the strength and ductility of RC columns. Cyclic lateral load tests were conducted on three specimens: one unreinforced specimen as reference, one specimen with the entire length of the column retrofitted, and one specimen with only the plastic hinge region of the column retrofitted. All specimens were tested under eccentric constant axial load and incrementally increasing lateral loading cycles with eccentricity. The implementation of steel rods resulted in significant improvement in ductility and an up to 60% increase in ultimate loading capacity. [ABSTRACT FROM AUTHOR]

This paper primarily presents an investigation into rectangular hollow section (RHS) cross- (or X-) connections with the branches fully laterally offset and loaded in axial tension. A set of 10 full-scale experimental specimens, carefully fabricated with noncritical welds, are tested in the laboratory, and the results are used to validate nonlinear finite-element models. To enhance the range of available data, the calibrated models are varied in an expanded parametric numerical study. A chord failure limit-state model based on a yield-line mechanism, which was identified in prior research on branch compression loading, is verified herein for branch tension loading. Furthermore, the limit state of branch failure is investigated by means of the combined experimental and numerical database produced. Design recommendations for laterally offset cross-connections loaded under branch tension, based on chord and branch failure modes, are presented. The application of current design recommendations for traditional cross-connections (with centered branches) to connections with full-width branches and laterally offset branches is also evaluated. [ABSTRACT FROM AUTHOR]

Three-dimensional (3D) concrete printing is increasingly becoming popular because it provides a powerful platform for the fabrication of structural components in freeform architectural shapes. Although manufacturing technology and material property improvement are advancing rapidly, the development of methods to predict the structural capacity of printed elements is lagging. This paper presents an experimental and numerical investigation to predict the axial load capacity of a printed concrete wall module. The module geometry contains two parallel thin wall sections connected by an internal sine wave. The thin wall section reduces the concrete consumption, and the internal sine wave provides lateral stability during printing and in the hardened state. It is a popular pattern printed by many researchers and in some real constructions. Two wall module specimens with the prescribed geometry were 3D-printed and tested under compression. The maximum loads of 2,890 and 2,924 kN were obtained for the first and second wall specimens, respectively. Additionally, samples were taken from different locations of a printed prototype to identify printed material characteristics. These experimental characteristics were then introduced to a finite-element numerical model for predicting the structural performance of the printed wall module under compression load. The results showed that the experimental maximum load and stiffness have 1% and 5% differences with numerical outputs, respectively. Based on such a validated model, the failure modes are discussed, and an analytical method is proposed for predicting the axial capacity for the prescribed geometry. [ABSTRACT FROM AUTHOR]

Pile foundations may be exposed to torsional loads caused by horizontal eccentric loads brought on waves, wind and earthquakes, as well as axial load brought on by supporting superstructures. This paper highlights a recent strategy to modify piles known as the finned pile. A series of experimental tests were conducted to increase the torsional capacity of a single pile with/without fins in sand under the influence of vertical loads (V), torsional loads (T) and combined loads (T → V), these experiments involved altering fins' length, width, shape, and number and knowing the effect of these variables on the piles' maximum torsional capacity. The vertical load-displacement response and the torsion-rotation response have been observed. The results showed that fins improve piles' torsional capacity. It also showed that on piles' maximum vertical capacity for independent vertical or torsional loads is different from that of piles under combined loading. It was found that fins' optimum geometry is that their length equal to 0.6 of the embedded pile's length and their width equal to the pile's diameter, where piles' maximum torsional capacity was (4.12 and 7.36) N.m for regular and finned piles, respectively. Fins increased piles' maximum torsional capacity by about 79%. [ABSTRACT FROM AUTHOR]

Full-scale axial load tests were performed on five screw injection piles founded in medium-dense to dense sand at a site in Delft, the Netherlands. Each pile was instrumented with distributed fiber-optic sensors along its full length, giving detailed insights into the shaft and base response under compression loading. The paper focuses on the pile base response and combines the test results with a newly compiled database of instrumented load tests on screw displacement piles in sand. Given the range of screw displacement piles on the market, the influence of different installation methods and pile geometries on the base resistance can be assessed through the database. In summary, the analysis showed that all screw displacement pile types tended to mobilize base capacities similar to bored or nondisplacement piles. Despite high variability in the database, no significant trend with pile geometry, such as length or diameter, was evident. [ABSTRACT FROM AUTHOR]

In this paper, an experimental, numerical and analytical study is conducted on a 2 × 1 bored pile group on saturated sand under combined loading. Initially, a single-degree-of-freedom system founded on the pile group is tested at the ETH Zurich drum centrifuge under vertical, lateral and pushover loading, gaining insights and deriving benchmark results for validation of finite-element (FE) models. The latter account for non-linear soil–pile interaction, using hypoplasticity for sand and appropriate modelling of interfaces and pile response. Combining centrifuge and FE modelling, the governing resistance mechanisms are identified and quantified. The transition from model to prototype scale is achieved after careful consideration of scale effects. The concrete damaged plasticity model is employed to model the non-linear response of the reinforced concrete (RC) piles, accounting for axial load dependency of bending moment capacity. The prototype problem is studied parametrically, deriving failure envelopes for different levels of vertical loading. Distinguishable failure modes are identified, and the contribution of different resistance mechanisms is quantified. Finally, analytical failure envelopes are derived based on limit equilibrium, expanding Broms' theory to pile groups under combined loading. Accounting for the axial load dependency of RC bending moment capacity, the proposed closed-form solutions provide a useful design tool for engineering practice. [ABSTRACT FROM AUTHOR]

Premature shear failure in reinforced concrete (RC) beam–column joints (BCJs) or at the top of columns can significantly compromise a building's seismic response, leading to major damage or global collapse, as observed in the aftermath of recent seismic events. Local strengthening solutions based on the employment of fiber-reinforced polymers (FRPs) are effective at increasing shear strength and preventing the failure of BCJs, and are also quick and easy to apply. This has led to their increased use in recent postearthquake reconstruction processes. However, large-scale plans to mitigate seismic risk require strengthening solutions that produce a minimum level of disruption and do not prevent the use of buildings. This can be achieved only by conducting work from a structure's exterior. This paper, therefore, proposes a novel FRP strengthening layout for exterior RC BCJs that combines the use of quadriaxial fabric and mechanical FRP spike anchors. In order to validate the proposed solution and quantify the effects of the number of layers and anchors, four full-scale BCJs are tested under a constant axial load and reversed cyclic displacement. The results are presented and discussed in relation to: global subassembly and local joint-panel response, energy dissipation, and the strain demand on the FRP fibers. A comparison with current available design formulations for anchored-FRP fabrics is made to produce preliminary design criteria. [ABSTRACT FROM AUTHOR]

Balanced fiber-reinforced rubber (FRR) pipes not only provide displacement compensation when transporting pressurized media but also prevent additional forces and displacements from being exerted on the connected pipeline system. Investigating the balanced performance of FRR pipes and the axial stiffness of balanced pipes is crucial for optimizing pipeline design and improving the reliability of pipeline systems. This paper develops a numerical model of FRR pipes that considers the nonlinearity of the rubber material and the interaction between the rubber matrix and fiber-reinforced layers. Using this model, the balanced performance of the pipe is calculated, and its axial stiffness under combined internal pressure and axial load is analyzed. Numerical results are compared with experimental data for validation. The results indicate that the pipe's balance is achieved through the combined effects of the elongation and rotation of the reinforcing fibers and the deformation of the rubber matrix, highlighting the significant impact of the rubber matrix on the mechanical performance of the FRR pipe. Furthermore, the pipe's balanced performance and axial stiffness are highly sensitive to the winding angle of reinforcing fibers. The proposed numerical model fills the gap in using numerical methods to evaluate the balanced performance of FRR pipes and provides valuable insights for their design and optimization. [ABSTRACT FROM AUTHOR]

This paper presents a comprehensive study focused on evaluating the strain generated within short concrete columns reinforced with glass-fiber-reinforced polymer (GFRP) bars and spirals under concentric compressive axial loads. This research was motivated by the lack of sufficient data in the literature regarding strain in such columns. Five full-scale RC columns were cast and tested, comprising four strengthened with GFRP reinforcement and one reference column reinforced with steel bars and spirals. This study thoroughly examined the influence of various test parameters, such as the reinforcement type, longitudinal reinforcement ratio, and spacing of spiral reinforcement, on the strain in concrete, GFRP bars, and spirals. The experimental results showed that GFRP–RC columns exhibited similar strain behavior to steel–RC columns up to 85% of their peak loads. The study also highlighted that the bearing capacity of the columns increased by up to 25% with optimized reinforcement ratios and spiral spacing, while the failure mode transitioned from a ductile to a more brittle nature as the reinforcement ratio increased. Additionally, it is preferable to limit the compressive strain in GFRP bars to less than 20% of their ultimate tensile strain and the strain in GFRP spirals to less than 12% of their ultimate strain to ensure the safe and reliable use of these materials in RC columns. This research also considers the prediction of the axial load capacities using established design standards permitting the use of FRP bars in compressive members, namely ACI 440.11-22, CSA-S806-12, and JSCE-97, and underscores their limitations in accurately predicting GFRP–RC columns' failure capacities. This study proposes an equation to enhance the prediction accuracy for GFRP–RC columns, considering the contributions of concrete, spiral confinement, and the axial stiffness of longitudinal GFRP bars. This equation addresses the shortcomings of existing design standards and provides a more accurate assessment of the axial load capacities for GFRP–RC columns. The proposed equation outperformed numerous other equations suggested by various researchers when employed to estimate the strength of 42 columns gathered from the literature. [ABSTRACT FROM AUTHOR]

In this paper, a novel T-shaped steel–concrete composite shear wall (TSCCW) is proposed. Low-cycle reciprocating tests were carried out on the TSCCW to investigate its performance in terms of its damage characteristics, hysteretic properties, energy dissipation capacity, stiffness degradation and ductility. A numerical model was established on the basis of the tests, and the correctness of the numerical model was verified. Afterwards, parameters such as shear span ratio, axial load ratio, rebar diameter, steel thickness, concrete strength grade and axial compression position were analyzed. The results show that the shear span ratio has a great influence on the performance of the TSCCW. A reduction in the shear span ratio from 2.1 to 1 reduces its stiffness by 333%. An increase in the axial load ratio will increase the load carrying capacity and stiffness of the TSCCW, and the deformation capacity will first increase and then decrease; it is recommended that the axial load ratio should be taken as 0.4. Increasing the steel thickness will improve the load carrying capacity, stiffness, deformation capacity and energy dissipation capacity of the TSCCW to a certain extent. Increasing the reinforcement diameter has less effect on the seismic performance of the TSCCW. [ABSTRACT FROM AUTHOR]

Soft hang-off is an emergency operation for drilling risers to survive under harsh environments. Buckling of the suspended riser and overstroke of the tensioner piston rod would probably occur. Conventional analysis methods usually ignored the dynamic interaction of the riser and tension fluctuation. This paper is devoted to developing an improved coupled model for the axial dynamic analysis of the riser under soft hang-off mode. In the developed model, the mathematical model of the tensioner was established considering gas state variations, internal friction and pressure loss, the mechanical model of the riser considering axial hydrodynamic load was developed, and the two models were coupled through the kinematic variables. A case study is carried out to analyse the axial dynamic characteristics of the riser under soft hang-off mode, and the comparison showed that the conventional tensioner models will underestimate the axial dynamic response of the riser in soft hang-off mode. [ABSTRACT FROM AUTHOR]

This paper presents an experimental study of the seismic behavior of concrete columns reinforced with glass fiber-reinforced polymer (GFRP) bars. Seven full-scale square columns were tested under sustained compressive axial loading combined with monotonic or cyclic lateral loading. The test program included two types of reinforcement (GFRP and steel bars) and different axial load levels (0, 20, and 33% of the axial capacity). The experiments showed that GFRP reinforcement could be used in concrete columns subjected to lateral loads, provided that ties are capable of properly confining the concrete core up to failure, thereby contributing to improving their deformation and energy dissipation capacity. Tests also confirmed the influence of the axial load level on the loadbearing capacity, deformation, and energy dissipation capacity of GFRP-reinforced concrete columns. [ABSTRACT FROM AUTHOR]

• Prior work through continuum finite-element studies on steel columns ([7]; [24]) demonstrates that the preceding findings are substantiated even in cases where axial load demands on steel columns remain low. Pertinent data for steel columns specifically on collapse have been presented in prior work ([6]; and the original paper), whereas for RC beams and columns the reader is referred to other pertinent work ([19]; [16]; [15]). Unlike prior testing programs on steel columns ([18]), the original paper considered as part of their testing program the fact that there is axial load deterioration due to redistribution of axial forces once an end column is damaged. [Extracted from the article]

The current paper explores a novel approach for determining temperature variations by integrating the modal parameters and AI techniques. The research focuses on the development of a comprehensive dataset for training an AI model encompassing an analytical method that considers thermal conditions and natural frequencies. Traditional methods of temperature measurement, like infrared and platinum resistance thermometers, often face limitations in terms of accuracy, especially in complex or dynamic environments having an uncertainty of ±3.6 °C [1], respectively ±0.2 °C [2]. In this study, we propose a methodology that harnesses the inherent relationship between axial loads caused by temperature variations and the change in natural frequencies of a double clamped steel beam. The measured natural frequency data is collected and fed into the AI model, specifically, for a robust temperature estimation, obtaining a maximum predicted temperature deviation of 0.386 °C. [ABSTRACT FROM AUTHOR]

Steel side-plate connections are reliable load path alternatives because they eliminate the fabrication challenges associated with continuity plates, especially for concrete-filled tubes (CFTs). In this paper, a new easy-to-fabricate moment connection for connecting I-beams to CFT columns using the monolithic side-plate technique is proposed. In this connection, the vertical side plates are entirely replaced by column webs to save steel material by eliminating the use of double steel plates in the connection panel zone and resolving the biaxial fabrication issues associated with the lack of welding access between the orthogonal side plates and the column. Four full-scale experimental tests consisting of two couples of relatively identical bolted and welded connections were conducted under a cyclic lateral displacement control loading protocol and a constant compressive axial load was applied to the column to evaluate the seismic performance of the connection. Furthermore, standard geometrical limitations, such as the column width and beam depth, were challenged. The results indicated that the new proposed connection exhibits sufficient stiffness and high level of ductility up to more than 4% of story drift without any strength degradation, implying that this new connection can be classified as a prequalified rigid moment connection to be used in special moment frames (SMFs) located in high seismic regions. In this paper, a monolithic side-plate connection is proposed and four full-scale specimens with oversized geometrical characteristics are experimentally investigated. The favorable results of this study show that this connection can be used as a prequalified rigid beam-to-column moment connection in intermediate and special steel moment frames consisting of box columns. The proposed easy-to-implement connection offers advantages such as decreased weight, fewer welding operations, and biaxial connection capability, which are not possible with conventional side plates. This connection is successfully implemented in an IMAX multicomplex building, with 151,676 m2 gross area and 82.32 m height. The proposed idea is applicable to any project with large box-shaped columns in high seismic regions and the achievements of this study can provide experimental support for the seismic design of these buildings. Critical factors in the connection performance are the column width and side-plate geometry, and considering other specific aspects of this connection, there is a lot of potential for further numerical and experimental investigations. Although not shown in this work, the proposed approach gives us the necessary flexibility to easily develop a biaxial moment connection, and further research is recommended in this case. [ABSTRACT FROM AUTHOR]

The dual-drive ball screw pair serves as a crucial element within the fixed gantry machine tool with cross-rail movement. When in service, the dual-drive ball screw pair experiences variations in axial load, impacting the contact load distribution of the ball screw pair. A calculation model for determining the axial load offset of the dual-drive ball screw pair is proposed to investigate the variation in axial load. The impact of the geometric error associated with the guide rail and the position of the slide are considered. This paper presents the contact load distribution model for the dual-drive ball screw pair. This study investigates the contact load and contact angle distribution of the dual-drive ball screw pair during the machine tool in service. Additionally, based on fractal theory, the stiffness models of individual micro-convex body and contact surfaces have been established. This study provides a comprehensive analysis of the contact stiffness of the ball screw pair, considering the influence of guide rail geometric error and slide position. In addition, the three-dimensional surface morphology of ball screw pair is obtained by experiments. This paper investigates the contact stiffness distribution of dual-drive ball screw pair during service. [ABSTRACT FROM AUTHOR]

This paper presents an improved design approach based on the direct strength method (DSM) in American Iron and Steel Institute (AISI) design specification S100 for cold-formed steel (CFS) built-up closed cross-section columns subjected to local, global, and local–global interaction buckling modes. Initially, the failure mode and load data corresponding to various design parameters such as intermediate fastener connection spacing, boundary conditions, material properties, slenderness, and cross sections from various researchers are collected, including the authors' test results. The design predictions using the current DSM design provisions are compared with the collected test results. The results show that the current DSM approach requires improvisation to adequately predict the axial compression load. The data are then analyzed to understand the behavioral features of the built-up closed cross-section column such as limit for interaction buckling, erosion of strength due to arrant interaction buckling, and increase in strength due to flange or web overlapping effect. The interpretation methods used to improve the current design approach are presented. The original DSM design procedure is improved by failure mode classification and modified slenderness to account for increase and erosion in strength. Finally, the safety (accuracy and reliability) of the design predictions from the improved DSM-based approach is assessed using the large amount of data collected. Since the introduction of the direct strength method to the North American Specification for the Design of Cold-Formed Steel Structural Members (AISI S100) in 2001, it has gained traction among design engineers due to its simplicity, advantages over other design methods, and specific design curves for individual buckling modes. To implement the DSM for CFS built-up members, several researchers have proposed different design approaches, and research is still happening. This study is also aimed toward the same objective but is specific to the local–global interaction in built-up members. It is demonstrated why the DSM prediction is unsafe for CFS built-up members with larger intermediate fastener connection spacing and excessively safe for CFS built-up members with closer intermediate fastener connection spacing. An intermediate fastener connection spacing limit that separates the local–global interaction buckling and element overlapping effect is determined. A design proposal for limiting the interaction buckling mode and considering the overlapping effect of elements in the DSM design method is suggested. More specifically, the proposed design method is in line with the current AISI approach so the designer need not confuse how to use this new design approach in practice. Therefore, for further ease of understanding, two design examples for built-up closed cross-section columns—(1) subjected to local–global interaction buckling; and (2) subjected to element overlapping effect—are included in this paper. It is also recommended that future research may focus on further classifying the AISI main specification sections, E2 and F2 (simple classifications based on the global failure modes), based on the interaction buckling modes in built-up cross-section members. [ABSTRACT FROM AUTHOR]

During an earthquake, the casualties and economic loss due to infrastructure failure, such as bridges, are prohibitive. In addition, the deterioration in the steel reinforcements in bridges due to corrosion issues leads to significant structural damage and maintenance costs. As a novel form of composite structural member, hybrid fiber-reinforced polymer (FRP)-concrete‐steel double-skin tubular columns (DSTCs), which consist of an inner steel tube, an outer FRP tube, and a sandwich concrete layer between the two tubes, with enhanced corrosion and seismic resistance, could be employed as bridge members (e.g., bridge piers) in harsh environments, seismic zones, or both, to enhance the seismic resistance, and extend the serviceable life of the bridges, achieve a lower maintenance cost, or both. This paper presents an experimental study on the behavior of DSTC-to-RC foundation connections that are subjected to a combination of axial compression and lateral cyclic loading, with the embedment depth of the column footing, axial load ratio of DSTCs, thickness of FRP tubes, and the additional anchoring measures within the foundation connections as the main parameters to be explored. Based on the test results, design suggestions, which include the critical embedment depth of the column footing and reliable structural measures, were proposed for DSTC-to-RC foundation connections. [ABSTRACT FROM AUTHOR]

In this paper, a numerical modeling was developed to study (on the basis of the Paris law) the fatigue propagation paths of eccentric external (outer) cracks in circumferentially cracked round bars (CCRB) subjected to a cyclic type of loading in the form of either remote tensile loading or imposed axial displacement. Results show how the eccentricity (in relation to the wire axis) of the circular resistant ligament increases with the growth of outer circumferential cracks by subcritical fatigue mechanisms. This phenomenon is more pronounced when the solicitation consists of a remote tensile loading than when it is an axial displacement, when the initial eccentricity of the ligament increases (for a given initial diameter), and when the Paris exponent characteristic of the material rises. The paper also analyzes in depth the different situations regarding contact between crack faces during subcritical cyclic fatigue propagation, covering a wide range of cases including no contact, partial contact, and full contact depending on the ligament diameter (during the process of fatigue crack advance) and the relative eccentricity of the annular crack that loses its axial symmetry in relation to the round bar (cylinder) axis. In addition to the fatigue crack path study, closed-form stress intensity factor (SIF) solutions for the considered geometry (a cylinder with an outer annular crack) are provided in the form of third-degree polynomial expressions as a function of the ligament diameter and the crack eccentricity (both in dimensionless terms). [ABSTRACT FROM AUTHOR]

Channel steel-reinforced brick column technology has gained significant popularity in rural China due to its convenience and cost effectiveness. However, current research on channel steel reinforcement is sparse, and engineering applications often rely solely on construction experience. This reliance leads to significant construction errors, inconsistent reinforcement effects, and, in some cases, tragedies such as the collapse of Changsha's "4.29" self-built houses. Therefore, in this paper, experimental and simulation studies on brick columns reinforced with external channel steel were conducted, and the results show that channel steel reinforcement can significantly enhance the axial load capacity of brick columns. However, increased initial stress levels and height-to-thickness ratios substantially reduce the reinforcement effect. Under axial pressure, the outer channel steel fails mainly through bending and buckling instability. Still, due to its good ductility, its failure occurs later than the brick column after being restrained by sufficient wall screws. Based on the experimental and simulation results, a method for calculating the axial compressive bearing capacity of the reinforced column is proposed, providing theoretical support and engineering guidance for applying this reinforcement method. [ABSTRACT FROM AUTHOR]

Concrete-filled steel tubular (CFST) columns have been widely used in multi-story and high-rise frame structures. During the service period, they may suffer vehicle impact due to traffic accidents or terrorist attacks. This paper numerically evaluates the performance of CFST columns under vehicle impact and investigates the effects of carbon FRP (CFRP) wrapping arrangements on performance improvement of the columns. Before that, a numerical model was developed to simulate the responses of CFST columns without and with FRP wrapping under vehicle impact and post-impact axial compression, and then calibrated by reported tests. Evaluation results show that the performance of CSFT columns under vehicle impact is divided into five levels, i.e., no repair required, rapid repair required, minor repair needed, major repair needed, and replacement needed. The performance level decreases with the increase in the vehicle weight or speed and increases with the increase in the column diameter or steel tube thickness. The column height has little effects on the performance level. A higher axial load ratio, e.g., 0.5, might reduce the performance level. Besides, a CFST column tends to fail in flexure mode when hit by F800 medium truck, while it may fail in flexure & shear mode when hit by C2500 pickup truck. Investigation results indicate that FRP wrapping with each layer orientation of 90° (i.e., in the longitudinal direction) and 0° (i.e., in the hoop direction) present the best performance improvement for a CFST column possibly undergoing flexure & shear and flexure failure, respectively. The increase of the number of FRP layers effectively improves the performance levels of CFST columns but the excessive demand may be not economical. It is not necessary to employ an FRP wrapping range of 100% for improving the vehicular impact performance level of a CFST column to the expected one. [ABSTRACT FROM AUTHOR]

An SHS-CFSHS X-joint is fabricated by welding two square hollow section (SHS) braces to a concrete-filled square hollow section (CFSHS) chord. In this paper, the stress concentration factors (SCFs) of SHS-CFSHS X-joints are investigated through experimental tests and finite element analysis (FEA), with the hot spot stress method serving as the analytical approach. Eight specimens are designed and manufactured, with FE models built in software ANSYS. These FE models are validated against the test results. The specimens are tested under brace axial tension to determine the SCFs of the X-joints. It shows that the concrete filled in the chord effectively reduces the SCFs of the X-joints. To further explore various load conditions and the influence of the parameters, FEA is carried out and a total of 64 FE models are built. Based on the FEA results, multiple regression analysis is used to obtain the SCF formulae of SHS-CFSHS X-joints under axial tension load and in-plane bending load in the brace, respectively. Comparison and analysis of the SCF results obtained from experimental tests, the proposed formulae, and FE simulations reveal that the formulae presented in this study are both conservative and suitable for predicting SCFs. [ABSTRACT FROM AUTHOR]

Elastomeric isolation bearings exhibit complex coupled horizontal-vertical behavior. Most existing macroscopic models simulate the quasistatic test results well but have deficiencies in simulating the dynamic behavior of bearings. In this paper, the experimental observations of previous dynamic bearing tests were investigated. The simulation capacity of existing macroscopic models was checked by comparison with the test data. The results show that the calculated axial load and hysteresis loops exhibit undesired oscillations under dynamic excitation. The intrinsic deficiency of existing models in simulating the dynamic response of a bearing was identified as the coupling or off-diagonal terms in the tangent stiffness matrix and the variation of vertical stiffness of the model. Motivated from this key observation, a new macroscopic model was developed to account for the dynamic behavior of bearings, followed by the suggestion of its numerical implementation. Through the introduction of a new axial load expression, the tangent stiffness matrix of the new model was semidecoupled, and the vertical stiffness of the new model remains unchanged, which reduced the interaction between the horizontal and vertical behavior. The simulation capacity of the new model was then validated by comparison with previous test data. The results show that the new model effectively captures the axial load variation and hysteresis loop of the bearings under dynamic excitations. Moreover, it was found that the consideration of the bearing height improved the simulation accuracy, and the size effect of the bearing is critical for isolated structures with large bearing-to-superstructure-height ratio, such as low- to medium-span bridges. [ABSTRACT FROM AUTHOR]

In order to explore the influence of different working conditions on the mechanical properties of dovetail joints, in this paper, the "Qing Dynasty Engineering Rules" of the Ministry of Qing Dynasty and "Wood Construction Technology of Ancient Chinese Buildings" were used as the weighing standards, using the results of wood properties tests conducted by other scholars as a reference, the numerical simulation of pseudo-static load was carried out on the dovetail joints of Qing Dynasty based on the finite element software ABAQUS. The influence of different angles outside the plane of tenon, different materials, different axial loads, and different load positions on the mechanical properties of dovetail tenon joints was investigated. The results showed that: 1) The hysteretic curves of dovetail mortise and tenon are all inverted z-shape. 2) The maximum bending moments at dovetail joints were 0.896, 0.914 kN·m and 0.979 kN·m when the lateral angles of the Fangs were 0°, 1.41° and 2.82°, respectively. When the axial load at the top of the column increases from 0 to 50 kN, the two-way maximum bending moments of dovetail joints change from 0.896 kN·m and 0.523 kN·m to 2.680 kN·m and 5.129 kN·m respectively. The two-way yield moment changed from 0.823 kN·m and 0.473 kN·m to 2.366 kN·m and 4.172 kN·m respectively. When the axial load at the top of the column increases from 50 kN to 100 kN, the changes of the two-way maximum bending moment and yield bending moment do not exceed 1%. 3) The peak viscous damping coefficients of dovetail joints corresponding to horizontal displacements of 0, 25 mm, and 50 mm applied on the beam side are 22.05%, 28.50%, and 29.38%, respectively. [ABSTRACT FROM AUTHOR]

The compressor serves as a crucial component that influences the performance of the gas turbine engine. Researchers have been endeavoring to explore compressor types that possess a high loading level and high-efficiency characteristics concurrently. In this study, tandem blade technology was applied to a transonic ultra-highly loaded axial compressor, and the Baseline single-blade rotor was replaced by a tandem rotor to take into account the loading level and compressor performance. Detailed investigations were carried out to identify the effects on the aerodynamic performance of the ultra-highly loaded stage and the fundamental flow mechanism within the tandem-rotor stage. This paper presents original design maps for the tandem-rotor stage, and the selection criteria for tandem parameters in tandem-rotor stage are refined. The results indicate that the peak efficiency improved by 0.83%, the stall margin increased by 2.16%, and the choke flow rate rose by 0.30% for the optimal tandem-rotor configuration. The meridional division position of the rotor primarily affects the ratio of loading of the front and rear blades, while the circumferential relative position of the tandem rotor mainly influences the channel types formed by the front and rear blades. Larger values for the meridional division position parameter and smaller values for circumferential relative position parameter should be selected for the tandem rotor design to optimize both the isentropic efficiency and total pressure ratio. This investigation offers the theoretical foundation for the design of a transonic ultra-highly loaded tandem-rotor compressor. [ABSTRACT FROM AUTHOR]

This paper focuses on the experimental investigation of the axial load capacity of CFT (concrete-filled steel tube) columns under actual construction conditions during building reconstruction. A total of four samples were loaded up to failure. The varied parameters were the column length and absence/presence of the concrete infill within the steel tube. Further, the analysis is extended to developing a numerical model in the finite element-based software ABAQUS version 6.9. This numerical model includes material and geometrical nonlinearities and was validated with the experimental results. The contribution of the concrete core to the column capacity and the concrete core confinement effect are discussed. Finally, the column capacity was calculated according to several design codes: the Eurocode 4 with and without considering the confinement effect, American specifications, Australian standards, the American Institute of Steel Construction, and the Architectural Institute of Japan. The Eurocode 4 considering the confinement effect provides the closest results to those obtained in the tests. [ABSTRACT FROM AUTHOR]

This paper experimentally and analytically investigated the damage and seismic behavior of concrete walls reinforced by low-bond ultra-high-strength (LBUHS) bars. To this end, four half-scale rectangular concrete walls were fabricated and tested under reversed cyclic loading and constant axial compression. The test variables were the shear span ratio and the axial load ratio. Based on the test results, the propagation of cracks on the wall surface, the maximum strain capacity of concrete, the hysteresis loops and envelope curves, the residual drifts, and the strain distributions of LBUHS rebars were presented and discussed. The experimental results showed that all the test walls could exhibit drift-hardening capability until at least a 2.0% drift ratio if LBUHS rebars were anchored by nuts at their ends. The test results also indicated that the maximum strain capacity of concrete was above 0.86%, much larger than the currently recommended 0.4%. After unloading from the transient drift ratios of 2.0% and 2.5% for the walls with shear span ratios of 1.5 and 2.0, respectively, the measured residual drift ratios were controlled below 0.4%, which is less than the critical drift ratio (0.5%) having 98% repairable probability recommended in the FEMA document (P-58) for general concrete structures. Furthermore, a numerical method was presented to evaluate the cyclic response of the test walls, and a comparison between the experimental and the calculated results verified the reliability and accuracy of the proposed numerical method. [ABSTRACT FROM AUTHOR]

As an effective measure to decrease the residual displacement under earthquakes, unbonded prestressed concrete (UBPRC) columns have been carefully investigated in previous research, while the influence of the complex characteristics of near-fault excitations on the residual displacement of UBPRC is less mentioned. This paper, therefore, focuses on the influence mechanism of the pulse effect and vertical effect of near-fault ground motions on the residual displacement of UBPRC columns. The residual displacement, at first, is formulated as a function of the coupled parameter T1-p (the ratio of the structural period to the pulse period). Then, the effect of near-fault vertical ground motion on the residual displacement is qualified based on the established mathematical model. Further, the model has been applied to investigate the effect of structural properties (dead load axial compression ratio, longitudinal reinforcement ratio, prestressing axial compression ratio, prestressing reinforcement ratio) on the residual displacement of UBPRC columns subjected to the joint action of horizontal and vertical ground motions. This research provides a quantitative methodology to quickly obtain the residual displacement spectra of the UBPRC columns under varying conditions combined with ground motion and structural parameters. [ABSTRACT FROM AUTHOR]

Featured Application: Inelastic analysis of RC slender beam elements under cyclic loading. The proposed mathematical model, described in detail in Part I of the present paper, aims to solve the common numerical problems that currently characterize classic fiber models when used with a moderate fiber grid for reasons of computational cost. To confirm these objectives, comparisons were made between analytical predictions of the model with experimental results of RC specimens and of a 2D scaled frame for a wide range of parameters that mainly concern slender specimens without significant influence of the bond slip phenomenon, different types of cross section shapes, and various loading histories. The agreement between analytical to experimental results was found to range from very good to excellent in some cases. [ABSTRACT FROM AUTHOR]