Search

Purpose: This study investigated the effects of the contact percentage (BMC%) of three-dimensional (3D) bone-to-miniscrew specimens in relation to host bone quality on initial miniscrew stability. Furthermore, their correlations were evaluated. Methods: Orthodontic miniscrews (1.6 mm in diameter and 11 mm in length) were inserted into four types of artificial bones to measure the maximum insertion torque value (ITV). The miniscrew and artificial foam bone specimens were also scanned using microcomputed tomography, and the obtained images were imported into Mimics software to reconstruct the 3D models and calculate the BMC%. The Kruskal–Wallis test, Wilcoxon rank-sum test with Bonferroni adjustment, and Spearman correlations were applied for statistical and correlation analyses. Results and Conclusions: Inserting the orthodontic miniscrew into artificial foam bone exhibiting higher bone quality resulted in higher maximum ITV and BMC%. The initial implant stability, quantified using ITV, was strongly positively (r = 0. 9 7) and correlated with BMC%, as measured from microcomputed tomography images. [ABSTRACT FROM AUTHOR]

This study evaluated the effect of the cyclic stretching speed on the force degradation of orthodontic elastics. Forty-five natural rubber bands (3M Unitek™) were stretched at different speeds in three groups: (1) static stretching test, (2) cyclic stretching test at a speed of 80 mm/min, and (3) cyclic stretching at a speed of 160 mm/min. A material tester and customized strain gauge were used to measure the residual force of the elastics in 37°C artificial saliva at different times. One-way repeated-measure analysis of variance followed by Scheffe's post-hoc comparison and t-test were used for statistical analysis. In Group 1, the force of the elastics degraded with time, with two separate phases being observed - distinctive degradation after 15 min and stabilization after 120 min. The cyclic stretching in Group 2 produced a significant deviation in the residual force and the initial force from the first minute, and stabilization after 300 min. After 1,440 min, 60% of the bands had snapped. Under accelerated stretching, no areas of relative stability were observed between the start of stretching to the start of breaking. After 1,440 high-speed stretches, 87% of the elastics in Group 3 snapped. These results indicate that the stretching speed affects the stability of the residual force of elastics. Cyclic stretching at high speed immediately induces a rapid degradation of the elastic's force and increases its probability of breakage. [ABSTRACT FROM AUTHOR]

In orthodontic treatment, the efficiency of tooth movement is affected by the frictional force between the archwire and bracket slot. This study evaluated the static and kinetic frictional forces produced in different combinations of orthodontic archwires and brackets. Three types of archwires [stainless steel, nickel-titanium (NiTi) alloy, and beta-titanium (TMA) alloy] and two types of brackets (stainless steel and self-ligating) were tested. Both static and kinetic frictional forces of each archwire-bracket combination were measured 25 times using a custom-designed apparatus. The surface topography and hardness of the archwires were also evaluated. All data were statistically analyzed using two-way analysis of variance and Tukey's test. The experiments indicated that the static frictional force was significantly higher than the kinetic frictional force in all archwire-bracket combinations not involving TMA wire. TMA wire had the highest friction, followed by NiTi wire, and then stainless steel wire when using the stainless steel bracket. However, there was no difference between NiTi and stainless steel archwires when using the self-ligating bracket. For TMA wire, the friction was higher when using the stainless steel bracket than when using the self-ligating bracket. Scanning electron microscopy indicated that stainless steel wire exhibited the smoothest surface topography. The hardness decreased in the order of stainless steel wire > TMA wire > NiTi wire. This study demonstrates that the frictional forces of brackets are influenced by different combinations of bracket and archwire. The reported data will be useful to orthodontists. [ABSTRACT FROM AUTHOR]