Search

Surface defects of metal halide perovskite nanocrystals (PNCs) substantially compromise the optoelectronic performances of the materials and devices via undesired charge recombination. However, those defects, mainly the vacancies, are structurally entangled with each other in the PNC lattice, necessitating a delicately designed strategy for effective passivation. Here, a synergistic metal ion doping and surface ligand exchange strategy is proposed to passivate the surface defects of CsPbBr 3 PNCs with various divalent metal (e.g., Cd 2+ , Zn 2+, and Hg 2+ ) acetate salts and didodecyldimethylammonium (DDA + ) via one-step post-treatment. The addition of metal acetate salts to PNCs is demonstrated to suppress the defect formation energy effectively via the ab initio calculations. The developed PNCs not only have near-unity photoluminescence quantum yield and excellent stability but also show luminance of 1175 cd m -2 , current efficiency of 65.48 cd A -1 , external quantum efficiency of 20.79%, wavelength of 514 nm in optimized PNC light-emitting diodes with Cd 2+ passivator and DDA ligand. The "organic-inorganic" hybrid engineering approach is completely general and can be straightforwardly applied to any combination of quaternary ammonium ligands and source of metal, which will be useful in PNC-based optoelectronic devices such as solar cells, photodetectors, and transistors., (© 2023 The Authors. Advanced Science published by Wiley-VCH GmbH.)

The limited conductivity of existing transparent conducting oxide (TCO) greatly restricts the further performance improvement of perovskite solar cells (PSCs), especially for large-area devices. Herein, buried-metal-grid tin-doped indium oxide (BMG ITO) electrodes are developed to minimize the power loss caused by the undesirable high sheet resistance of TCOs. By burying 140-nm-thick metal grids into ITO using a photolithography technique, the sheet resistance of ITO is reduced from 15.0 to 2.7 Ω sq -1 . The metal step of BMG over ITO has a huge impact on the charge carrier transport in PSCs. The PSCs using BMG ITO with a low metal step deliver power conversion efficiencies (PCEs) significantly better than that of their counterparts with higher metal steps. Moreover, compared with the pristine ITO-based PSCs, the BMG ITO-based PSCs show a smaller PCE decrease when scaling up the active area of devices. The parallel-connected large-area PSCs with an active area of 102.8 mm 2 reach a PCE of 22.5%. The BMG ITO electrodes are also compatible with the fabrication of inverted-structure PSCs and organic solar cells. The work demonstrates the great efficacy of improving the conductivity of TCO by BMG and opens up a promising avenue for constructing highly efficient large-area PSCs., (© 2023 Wiley-VCH GmbH.)

The severely insufficient operational lifetime of perovskite light-emitting diodes (LEDs) is incompatible with the rapidly increasing external quantum efficiency, even as it approaches the theoretical limit, thereby significantly impeding the commercialization of perovskite LEDs. In addition, Joule heating induces ion migration and surface defects, degrades the photoluminescence quantum yield and other optoelectronic properties of perovskite films, and induces the crystallization of charge transport layers with low glass transition temperatures, resulting in LED degradation under continuous operation. Here, a novel thermally crosslinked hole transport material, poly(FCA 60 -co-BFCA 20 -co-VFCA 20 ) (poly-FBV), with temperature-dependent hole mobility is designed, which is advantageous for balancing the charge injection of the LEDs and limiting the generation of Joule heating. The optimised CsPbI 3 perovskite nanocrystal LEDs with poly-FBV realise approximately a 2-fold external quantum efficiency increase over the LED with commercial hole transport layer poly(4-butyl-phenyl-diphenyl-amine) (poly-TPD), owing to the balanced carrier injection and suppressed exciton quenching. Moreover, because of the Joule heating control provided by the novel crosslinked hole transport material, the LED utilising crosslinked poly-FBV has a 150-fold longer operating lifetime (490 min) than that utilizing poly-TPD (3.3 min). The study opens a new avenue for the use of PNC LEDs in commercial semiconductor optoelectronic devices., (© 2023 Wiley-VCH GmbH.)

Metal halide perovskite based tandem solar cells are promising to achieve power conversion efficiency beyond the theoretical limit of their single-junction counterparts. However, overcoming the significant open-circuit voltage deficit present in wide-bandgap perovskite solar cells remains a major hurdle for realizing efficient and stable perovskite tandem cells. Here, a holistic approach to overcoming challenges in 1.8 eV perovskite solar cells is reported by engineering the perovskite crystallization pathway by means of chloride additives. In conjunction with employing a self-assembled monolayer as the hole-transport layer, an open-circuit voltage of 1.25 V and a power conversion efficiency of 17.0% are achieved. The key role of methylammonium chloride addition is elucidated in facilitating the growth of a chloride-rich intermediate phase that directs crystallization of the desired cubic perovskite phase and induces more effective halide homogenization. The as-formed 1.8 eV perovskite demonstrates suppressed halide segregation and improved optoelectronic properties., (© 2023 The Authors. Advanced Materials published by Wiley-VCH GmbH.)

Interfaces in thin-film photovoltaics play a pivotal role in determining device efficiency and longevity. In this work, the top surface treatment of mixed tin-lead (≈1.26 eV) halide perovskite films for p-i-n solar cells is studied. Charge extraction is promoted by treating the perovskite surface with piperazine. This compound reacts with the organic cations at the perovskite surface, modifying the surface structure and tuning the interfacial energy level alignment. In addition, the combined treatment with C 60 pyrrolidine tris-acid (CPTA) reduces hysteresis and leads to efficiencies up to 22.7%, with open-circuit voltage values reaching 0.90 V, ≈92% of the radiative limit for the bandgap of this material. The modified cells also show superior stability, with unencapsulated cells retaining 96% of their initial efficiency after >2000 h of storage in N 2 and encapsulated cells retaining 90% efficiency after >450 h of storage in air. Intriguingly, CPTA preferentially binds to Sn 2+ sites at film surface over Pb 2+ due to the energetically favored exposure of the former, according to first-principles calculations. This work provides new insights into the surface chemistry of perovskite films in terms of their structural, electronic, and defect characteristics and this knowledge is used to fabricate state-of-the-art solar cells., (© 2023 Wiley-VCH GmbH.)

Semiconducting lead halide perovskite nanocrystals (PNCs) are regarded as promising candidates for next-generation optoelectronic devices due to their solution processability and outstanding optoelectronic properties. While the field of light-emitting diodes (LEDs) and photovoltaics (PVs), two prime examples of optoelectronic devices, has recently seen a multitude of efforts toward high-performance PNC-based devices, realizing both devices with high efficiencies and stabilities through a single PNC processing strategy has remained a challenge.  In this work, diphenylpropylammonium (DPAI) surface ligands, found through a judicious ab-initio-based ligand search, are shown to provide a solution to this problem. The universal PNC ink with DPAI ligands presented here, prepared through a solution-phase ligand-exchange process, simultaneously allows single-step processed LED and PV devices with peak electroluminescence external quantum efficiency of 17.00% and power conversion efficiency of 14.92% (stabilized output 14.00%), respectively. It is revealed that a careful design of the aromatic rings such as in DPAI is the decisive factor in bestowing such high performances, ease of solution processing, and improved phase stability up to 120 days. This work illustrates the power of ligand design in producing PNC ink formulations for high-throughput production of optoelectronic devices; it also paves a path for "dual-mode" devices with both PV and LED functionalities., (© 2022 Wiley-VCH GmbH.)

Inverted-structure metal halide perovskite solar cells (PSCs) have attractive advantages like low-temperature processability and outstanding device stability. The two-step sequential deposition method shows the benefits of easy fabrication and decent performance repeatability. Nevertheless, it is still challenging to achieve high-performance inverted PSCs with similar or equal power conversion efficiencies (PCEs) compared to the regular-structure counterparts via this deposition method. Here, an improved two-step sequential deposition technique is demonstrated via treating the bottom organic hole-selective layer with the binary modulation system composed of a polyelectrolyte and an ammonium salt. Such improved sequential deposition method leads to the spontaneous refinement of up and buried interfaces for the perovskite films, contributing to high film quality with significantly reduced defect density and better charge transportation. As a result, the optimized PSCs show a large enhancement in the open-circuit voltage by 100 mV and a dramatic lift in the PCE from 18.1% to 23.4%, delivering the current state-of-the-art performances for inverted PSCs. Moreover, good operational and thermal stability is achieved upon the improved inverted PSCs. This innovative strategy helps gain a deeper insight into the perovskite crystal growth and defect modulation in the inverted PSCs based on the two-step sequential deposition method., (© 2022 Wiley-VCH GmbH.)

Optoelectronic properties are unraveled for formamidinium tin triiodide (FASnI 3 ) thin films, whose background hole doping density is varied through SnF 2 addition during film fabrication. Monomolecular charge-carrier recombination exhibits both a dopant-mediated part that grows linearly with hole doping density and remnant contributions that remain under tin-enriched processing conditions. At hole densities near 10 20 cm -3 , a strong Burstein-Moss effect increases absorption onset energies by ≈300 meV beyond the bandgap energy of undoped FASnI 3 (shown to be 1.2 eV at 5 K and 1.35 eV at room temperature). At very high doping densities (10 20 cm -3 ), temperature-dependent measurements indicate that the effective charge-carrier mobility is suppressed through scattering with ionized dopants. Once the background hole concentration is nearer 10 19 cm -3 and below, the charge-carrier mobility increases with decreasing temperature according to ≈T -1.2 , suggesting that it is limited mostly by intrinsic interactions with lattice vibrations. For the lowest doping concentration of 7.2 × 10 18 cm -3 , charge-carrier mobilities reach a value of 67 cm 2 V -1 s -1 at room temperature and 470 cm 2 V -1 s -1 at 50 K. Intraexcitonic transitions observed in the THz-frequency photoconductivity spectra at 5 K reveal an exciton binding energy of only 3.1 meV for FASnI 3 , in agreement with the low bandgap energy exhibited by this perovskite., (© 2018 The Authors. Published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Metal-halide perovskites offer great potential to realize low-cost and flexible next-generation solar cells. Low-temperature-processed organic hole-transporting layers play an important role in advancing device efficiencies and stabilities. Inexpensive and stable hole-transporting materials (HTMs) are highly desirable toward the scaling up of perovskite solar cells (PSCs). Here, a new group of aniline-based enamine HTMs obtained via a one-step synthesis procedure is reported, without using a transition metal catalyst, from very common and inexpensive aniline precursors. This results in a material cost reduction to less than 1/5 of that for the archetypal spiro-OMeTAD. PSCs using an enamine V1091 HTM exhibit a champion power conversion efficiency of over 20%. Importantly, the unsealed devices with V1091 retain 96% of their original efficiency after storage in ambient air, with a relative humidity of 45% for over 800 h, while the devices fabricated using spiro-OMeTAD dropped down to 42% of their original efficiency after aging. Additionally, these materials can be processed via both solution and vacuum processes, which is believed to open up new possibilities for interlayers used in large-area all perovskite tandem cells, as well as many other optoelectronic device applications., (© 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Perovskite solar cells have shown a meteoric rise of power conversion efficiency and a steady pace of improvements in their stability of operation. Such rapid progress has triggered research into approaches that can boost efficiencies beyond the Shockley-Queisser limit stipulated for a single-junction cell under normal solar illumination conditions. The tandem solar cell architecture is one concept here that has recently been successfully implemented. However, the approach of solar concentration has not been sufficiently explored so far for perovskite photovoltaics, despite its frequent use in the area of inorganic semiconductor solar cells. Here, the prospects of hybrid perovskites are assessed for use in concentrator solar cells. Solar cell performance parameters are theoretically predicted as a function of solar concentration levels, based on representative assumptions of charge-carrier recombination and extraction rates in the device. It is demonstrated that perovskite solar cells can fundamentally exhibit appreciably higher energy-conversion efficiencies under solar concentration, where they are able to exceed the Shockley-Queisser limit and exhibit strongly elevated open-circuit voltages. It is therefore concluded that sufficient material and device stability under increased illumination levels will be the only significant challenge to perovskite concentrator solar cell applications.

Novel nonspiro, fluorene-based, small-molecule hole transporting materials (HTMs) V1050 and V1061 are designed and synthesized using a facile three-step synthetic route. The synthesized compounds exhibit amorphous nature with a high glass transition temperature, a good solubility, and decent thermal stability. The planar perovskite solar cells (PSCs) employing V1050 generated an excellent power conversion efficiency of 18.3%, which is comparable to 18.9% obtained with the state-of-the-art Spiro-OMeTAD. Importantly, the devices based on V1050 and V1061 show better stability compared to devices based on Spiro-OMeTAD when aged without any encapsulation under uncontrolled humidity conditions (relative humidity around 60%) in the dark and under continuous full sun illumination.

The meteoric rise of the field of perovskite solar cells has been fueled by the ease with which a wide range of high-quality materials can be fabricated via simple solution processing methods. However, to date, little effort has been devoted to understanding the precursor solutions, and the role of additives such as hydrohalic acids upon film crystallization and final optoelectronic quality. Here, a direct link between the colloids concentration present in the [HC(NH 2 ) 2 ] 0.83 Cs 0.17 Pb(Br 0.2 I 0.8 ) 3 precursor solution and the nucleation and growth stages of the thin film formation is established. Using dynamic light scattering analysis, the dissolution of colloids over a time span triggered by the addition of hydrohalic acids is monitored. These colloids appear to provide nucleation sites for the perovskite crystallization, which critically impacts morphology, crystal quality, and optoelectronic properties. Via 2D X-ray diffraction, highly ordered and textured crystals for films prepared from solutions with lower colloidal concentrations are observed. This increase in material quality allows for a reduction in microstrain along with a twofold increase in charge-carrier mobilities leading to values exceeding 20 cm 2 V -1 s -1 . Using a solution with an optimized colloidal concentration, devices that reach current-voltage measured power conversion efficiency of 18.8% and stabilized efficiency of 17.9% are fabricated., (© 2017 The Authors. Published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Perovskite solar cells are considered a promising technology for solar-energy conversion, with power conversion efficiencies currently exceeding 20 %. In most of the reported devices, Spiro-OMeTAD is used for positive-charge extraction and transport layer. Although a number of alternative hole-transporting materials with different aromatic or heteroaromatic fragments have already been synthesized, a cheap and well-performing hole-transporting material is still in high demand. In this work, a two-step synthesis of a carbazole-based hole-transporting material is presented. Synthesized compounds exhibited amorphous nature, good solubility and thermal stability. The perovskite solar cells employing the newly synthesized material generated a power conversion efficiency of 16.5 % which is slightly lower than that obtained with Spiro-OMeTAD (17.5 %). The low-cost synthesis and high performance makes our hole-transport material promising for applications in perovskite-based optoelectronic devices., (© 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Metal halide perovskite thin films can be crystallized via a broad range of solution-based routes. However, the quality of the final films is strongly dependent upon small changes in solution composition and processing parameters. Here, this study demonstrates that a fractional substitution of PbCl 2 with PbI 2 in the 3CH 3 NH 3 I:PbCl 2 mixed-halide starting solution has a profound influence upon the ensuing thin-film crystallization. The presence of PbI 2 in the precursor induces a uniform distribution of regular quadrilateral-shaped CH 3 NH 3 PbI 3 perovskite crystals in as-cast films, which subsequently grow to form pinhole-free perovskite films with highly crystalline domains. With this new formulation of 3CH 3 NH 3 I:0.98PbCl 2 :0.02PbI 2 , this study achieves a 19.1% current-voltage measured power conversion efficiency and a 17.2% stabilized power output in regular planar heterojunction solar cells., (© 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Air-stable doping of the n-type fullerene layer in an n-i-p planar heterojunction perovskite device is capable of enhancing device efficiency and improving device stability. Employing a (HC(NH 2 ) 2 ) 0.83 Cs 0.17 Pb(I 0.6 Br 0.4 ) 3 perovskite as the photoactive layer, glass-glass laminated devices are reported, which sustain 80% of their "post burn-in" efficiency over 3400 h under full sun illumination in ambient conditions., (© 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

In this work, solar cells with a freshly made CH 3 NH 3 PbI 3 perovskite film showed a power conversion efficiency (PCE) of 15.4 % whereas the one with 50 days aged perovskite film only 6.1 %. However, when the aged perovskite was covered with a layer of Al 2 O 3 deposited by atomic layer deposition (ALD) at room temperature (RT), the PCE value was clearly enhanced. X-ray photoelectron spectroscopy study showed that the ALD precursors are chemically active only at the perovskite surface and passivate it. Moreover, the RT-ALD-Al 2 O 3 -covered perovskite films showed enhanced ambient air stability., (© 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.)

A robust and expedient gas quenching method is developed for the solution deposition of hybrid perovskite thin films. The method offers a reliable standard practice for the fabrication of a non-exhaustive variety of perovskites exhibiting excellent film morphology and commensurate high performance in both regular and inverted structured solar cell architectures., (© 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

V-shaped Tröger's base core has been investigated as a central linking unit in the synthesis of new charge-transporting materials for optoelectronic applications. The studied molecules have been synthesized in two steps from relatively inexpensive starting materials, and demonstrate high glass transition temperatures, good stability of the amorphous state, and comparatively high hole drift mobility (up to 0.011 cm(2)  V(-1)  s(-1) )., (© 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

A general strategy for the in-plane structuring of organic-inorganic perovskite films is presented. The method is used to fabricate an industrially relevant distributed feedback (DFB) cavity, which is a critical step toward all-electrially pumped injection laser diodes. This approach opens the prospects of perovskite materials for much improved optical control in LEDs, solar cells, and also toward applications as optical devices., (© 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

The mixed-halide perovskite FAPb(Bry I1-y )3 is attractive for color-tunable and tandem solar cells. Bimolecular and Auger charge-carrier recombination rate constants strongly correlate with the Br content, y, suggesting a link with electronic structure. FAPbBr3 and FAPbI3 exhibit charge-carrier mobilities of 14 and 27 cm(2) V(-1) s(-1) and diffusion lengths exceeding 1 μm, while mobilities across the mixed Br/I system depend on crystalline phase disorder., (© 2015 The Authors. Published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Dye-sensitized TiO2 can be used as the active layer of solar-cell devices without an additional hole-transporting material. In this architecture, holes are transported through the dye monolayer., (© 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Organic-inorganic perovskites are currently one of the hottest topics in photovoltaic (PV) research, with power conversion efficiencies (PCEs) of cells on a laboratory scale already competing with those of established thin-film PV technologies. Most enhancements have been achieved by improving the quality of the perovskite films, suggesting that the optimization of film formation and crystallization is of paramount importance for further advances. Here, we review the various techniques for film formation and the role of the solvents and precursors in the processes. We address the role chloride ions play in film formation of mixed-halide perovskites, which is an outstanding question in the field. We highlight the material properties that are essential for high-efficiency operation of solar cells, and identify how further improved morphologies might be achieved., (© 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

A self-adhesive laminate solar-cell electrode is presented based on a metal grid embedded in a polymer film (x-y conduction) and set in contact with the active layer using a pressure-sensitive adhesive containing a very low quantity (1.8%) of organic conductor, which self-organizes to provide z conduction to the grid. This ITO-free material performs in an identical fashion to evaporated gold in high-efficiency perovskite solar cells., (© 2014 The Authors. Published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

The field of solution-processed photovoltaic cells is currently in its second spring. The dye-sensitized solar cell is a widely studied and longstanding candidate for future energy generation. Recently, inorganic absorber-based devices have reached new record efficiencies, with the benefits of all-solid-state devices. In this rapidly changing environment, this review sheds light on recent developments in all-solid-state solar cells in terms of electrode architecture, alternative sensitizers, and hole-transporting materials. These concepts are of general applicability to many next-generation device platforms., (© 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Organolead trihalide perovskites are shown to exhibit the best of both worlds: charge-carrier mobilities around 10 cm2 V−1 s−1 and low bi-molecular charge-recombination constants. The ratio of the two is found to defy the Langevin limit of kinetic charge capture by over four orders of magnitude. This mechanism causes long (micrometer) charge-pair diffusion lengths crucial for flat-heterojunction photovoltaics.

Transient mobility spectroscopy (TMS) is presented as a new tool to probe the charge carrier mobility of commonly employed organic and inorganic semiconductors over the relevant range of charge densities. The charge density dependence of the mobility of semiconductors used in hybrid and organic photovoltaics gives new insights into charge transport phenomena in solid state dye sensitized solar cells., (Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Morphology control on the 10 nm length scale in mesoporous TiO(2) films is crucial for the manufacture of high-performance dye-sensitized solar cells. While the combination of block-copolymer self-assembly with sol-gel chemistry yields good results for very thin films, the shrinkage during the film manufacture typically prevents the build-up of sufficiently thick layers to enable optimum solar cell operation. Here, a study on the temporal evolution of block-copolymer-directed mesoporous TiO(2) films during annealing and calcination is presented. The in-situ investigation of the shrinkage process enables the establishment of a simple and fast protocol for the fabrication of thicker films. When used as photoanodes in solid-state dye-sensitized solar cells, the mesoporous networks exhibit significantly enhanced transport and collection rates compared to the state-of-the-art nanoparticle-based devices. As a consequence of the increased film thickness, power conversion efficiencies above 4% are reached., (Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)