Search

Far‐ultraviolet‐C (far‐UVC) light emitting diodes (LED) emitting at an emission wavelength of 226 nm with different n‐AlGaN contact layers, quantum well barriers, and quantum well numbers are compared regarding their emission power, operation voltage, and lifetime. Electroluminescence measurements show higher emission power but also an increased operation voltage with increasing Al mole fraction in the n‐AlGaN contact layer. Furthermore, it is found that both the mean emission power and the device lifetime decrease with increasing Al mole fraction (82–89%) of the quantum well barriers and therefore with increasing barrier height. Finally, 226 nm LEDs with 6 and 9 quantum wells are compared. It is observed that the sample with 9 quantum wells shows an around 30% lower mean emission power but, in contrast, the L70 lifetime of these LEDs is higher by a factor of around five. Based on these optimizations, 226 nm LEDs with a maximum external quantum efficiency of 0.28% (wall plug efficiency of 0.18%) as well as an emission power of 2.1 mW and an operation voltage of 9.6 V at 200 mA are realized. [ABSTRACT FROM AUTHOR]

The effect of the InGaN channel on the performance of high‐electron‐mobility transistors (HEMTs) through the Silvaco Atlas simulator is investigated in detail. It is shown that the 2D electron gas (2DEG) density and carrier confinement of the device can be enhanced by replacing the GaN channel with the InGaN channel. The higher 2DEG density significantly increases the saturation drain current density, thus improving the current drive capability of the device. Meanwhile, better carrier confinement alleviates the short channel effects (SCEs) and traps state‐related current collapse in the GaN buffer, effectively improving the reliability of the device. Better carrier confinement also increases the current gain cutoff frequency (fT) and maximum oscillation frequency (fmax) to 133 and 226 GHz, while the fT and fmax of conventional GaN channel HEMTs are 104 and 167 GHz, respectively. These results indicate that AlInGaN/InGaN HEMTs achieve better performance in direct current (DC) and radio frequency (RF). [ABSTRACT FROM AUTHOR]

Herein, the electron–hole wave function overlaps as well as the carrier confinement are both improved by an inversely graded Al‐composition design in the multiple‐quantum‐well (MQW) active region of deep‐ultraviolet light‐emitting diodes (DUV–LEDs). Simulation results show that at a current of 250 mA, the light output power (LOP) of the DUV–LEDs with graded composition MQWs has achieved a remarkable enhancement of 38.7% as compared to that with conventional MQWs, and the efficiency droop is significantly reduced from 32.2% to 9.3%. The enhanced performance is attributed to the increased wave function overlap of the electrons and holes due to the alleviated polarization electric field. Furthermore, the depth of quantum wells (QWs) is increased by the increased polarization‐induced charges and results in a better carrier confinement in the well layers. In addition, the LOP is further enhanced by 20.5% and the efficiency droop is reduced to 6.2% by engineering the last quantum barrier in the graded MQWs, which is attributed to the further reduction in the electron leakage. The proposed structure provides a valuable guideline for the high‐efficiency DUV–LEDs. [ABSTRACT FROM AUTHOR]

In this work, the InGaN/AlGaN multiple-quantum-well (MQW) near-ultraviolet (UV) light-emitting diodes (LEDs) with different aluminum compositions in the barrier layers are investigated and fabricated. The aluminum compositions of LED I, II, and III are 0, 2.5, and 3.85%, respectively. The light output powers of LED I, II, and III at an injection current of 350 mA are 95.46, 135.48 mW, and 179.54 mW, respectively. The light output power measured from LED III was 88% larger than that of LED I. The peak external quantum efficiency was enhanced from 9.24 to 17.26%. This result was attributed to the improvement of carrier confinement in the active region by using AlGaN-based barrier layers. The hot-cold effect of LEDs as functions of junction temperature currently is a very important key issue for actual application to LEDs. As the temperature increased, the injected carriers became excited and easily escaped from the active layer. Thus, the light output power of the LED decreased as the temperature increased. Compared with LED I and LED II, the light output power of LED III with better carrier confinement was decreased more slowly with increasing temperature. [ABSTRACT FROM AUTHOR]