Search

A kite‐shaped low‐band (LB) element loaded with mushroom‐shaped structure is proposed. The element has a bandpass characteristic for the electromagnetic wave within the frequency range of 3.4–3.8 GHz and can reduce the influence on the high‐band (HB) antenna in the dual‐band coaperture antenna. The LB elements operating in the 0.698–0.96 GHz frequency band are embedded in the massive multiple input, multiple output (MIMO) antenna. One prototype of the coaperture antenna is fabricated for demonstration. The measured results show that the pattern distortion of most of the antenna ports of the HB antenna is very small after adding the LB antenna. The maximum gain deviation of the traffic beam scanning within the range of ±60° is less than 0.57 dB, indicating that the LB element can effectively suppress scattering and is suitable for multiband coaperture base‐station antenna. [ABSTRACT FROM AUTHOR]

Reproductive traits of dairy cattle are bound to the actual efficiency of farm operation, which therefore show great economic importance. Among them, some traits were deemed to be simultaneously affected by service sire and mating cow. Service sires are proved to play an important role in reproduction process of cows. However, limited study explored the genetic effect of service sire (GESS), let alone the genomic prediction of this effect. In the present study, 2244 genotyped bulls together with phenotypic records were used to predict the GESS on conception rate, 56‐day non‐return rate, calving ease, stillbirth and gestation length. The feasibilities of multi‐step genomic best linear unbiased predictor (msGBLUP) and single‐step genomic best linear unbiased predictor (ssGBLUP) were investigated under different scenarios, that is, different marker densities and validation population. The predictive accuracies and unbiasedness for GESS ranged from 0.159 to 0.647 and from 0.202 to 2.018, respectively, when validated on young bulls, while the accuracies and unbiasedness ranged from 0.409 to 0.802 and 0.333 to 1.146 when validated on random split data sets. It is feasible to predict GESS on reproductive traits by using a linear mixed model and genomic data, and high‐density marker panel had limited contribution to the prediction. This research investigated the potential factors that influence the genomic prediction of GESS on reproductive traits and indicated the possibility of genomic selection on GESS, both in ideal and practical circumstances. [ABSTRACT FROM AUTHOR]

Integrating the single‐nucleotide polymorphisms (SNPs) significantly affecting target traits from imputed whole‐genome sequencing (iWGS) data into the genomic prediction (GP) model is an economic, efficient, and feasible strategy to improve prediction accuracy. The objective was to dissect the genetic architecture of intramuscular fat content (IFC) by genome wide association studies (GWAS) and to investigate the accuracy of GP based on pedigree‐based BLUP (PBLUP) model, genomic best linear unbiased prediction (GBLUP) models and Bayesian mixture (BayesMix) models under different strategies. A total of 482 Suhuai pigs were genotyped using an 80 K SNP chip. Furthermore, 30 key samples were selected for resequencing and were used as a reference panel to impute the 80 K chip data to the WGS dataset. The 80 K data and iWGS data were used to perform GWAS and test GP accuracies under different scenarios. GWAS results revealed that there were four major regions affecting IFC. Two important functional candidate genes were found in the two most significant regions, including protein kinase C epsilon (PRKCE) and myosin light chain 2 (MYL2). The results of the predictions showed that the PBLUP model had the lowest reliability (0.096 ± 0.032). The reliability (0.229 ± 0.035) was improved by replacing pedigree information with 80 K chip data. Compared with using 80 K SNPs alone, pruning iWGS SNPs with the R‐squared cutoff of linkage disequilibrium (0.55) led to a slight improvement (0.006), adding significant iWGS SNPs led to an improvement of reliability by 0.050 when using a one‐component GBLUP, a further increase of 0.033 when using a two‐component GBLUP model. For BayesMix models, compared with using 80 K SNPs alone, adding additional significant iWGS SNPs into one‐ or two‐component BayesMix models led to improvements of reliabilities for IFC by 0.040 and 0.089, respectively. Our results may facilitate further identification of causal genes for IFC and may be beneficial for the improvement of IFC in pig breeding programs. [ABSTRACT FROM AUTHOR]

Mo2NiB2 is a kind of cermet with excellent mechanical properties, stable chemical properties, and excellent corrosion resistance and is often used in wear‐resistant application fields, such as injection molding machine parts, can making tools and hot copper extruding dies. The brittleness of Mo2NiB2‐based cermets limits their wide application. Mo2NiB2‐based cermets were prepared by the vacuum sintering method, the effect of SiC whiskers (SiCw) on the microstructure and mechanical properties of cermets was investigated, and the toughening mechanism of SiCw on cermets was further discussed. The results indicate that with increasing SiCw content, the indentation fracture toughness (KIC), transverse fracture strength (TRS), and Vickers hardness (HV) of the cermets first increase and then decrease. The HV, TRS, and indentation fracture toughness of Mo2NiB2‐based cermets with 0.5 wt% SiCw are 1 113 HV, 1 620 MPa, and 27.97 MPa·m1/2, respectively, which are 16.8%, 22.7%, and 25% higher than those without SiCw. In the sliding friction tests, Mo2NiB2‐based cermets with 0.5 wt% SiCw have the smallest friction coefficient, low wear rate, and high wear resistance. SEM observation and analysis of the crack path and fracture surface showed that the toughening mechanism is whisker bridging, crack deflection, microcrack toughening, and whisker pull‐out. The results indicate that the addition of 0.5 wt% SiCw can effectively improve the mechanical properties of Mo2NiB2‐based cermets and further expand the application space of Mo2NiB2‐based cermets. [ABSTRACT FROM AUTHOR]

Rationale: Pyrotinib is an irreversible EGFR/HER2 inhibitor that has shown antitumor activity and tolerance in the treatment of breast cancer. Studies focused on its metabolic pathways and major metabolites are insufficient. In the evaluation of drug safety and therapeutic use, metabolite characterization is critical. The metabolism of pyrotinib in vitro was studied utilizing rat, dog and human hepatocytes in this study. Methods: Pyrotinib (10 μM) was incubated with hepatocytes in Williams' E medium. The metabolites were examined and profiled using ultrahigh‐performance liquid chromatography coupled with quadrupole/orbitrap high‐resolution mass spectrometry. The metabolite structures were deduced by comparing their precise molecular weights, fragment ions and retention times with those of the parent drug. Results: A total of 16 metabolites, including 6 novel ones, were discovered and structurally described under the present conditions. Oxidation, demethylation, dehydrogenation, O‐dealkylation and glutathione (GSH) conjugation were all involved in the metabolism of pyrotinib in hepatocytes. The most predominant metabolic route was identified as GSH conjugation (M5). Conclusions: This study generated valuable metabolite profiles of pyrotinib in several species, which will aid in the understanding of the drug's disposition in various species and in evaluating the contribution of metabolites to overall effectiveness and toxicity of pyrotinib. [ABSTRACT FROM AUTHOR]

The hardness and toughness of regenerated cemented carbides, in general, are contradictory. Therefore, it is critical to explore regenerated cemented carbides with both high hardness and high toughness. In this study, regenerated WC‐8‐wt% Co cemented carbide with SiC nanowhisker were prepared by low‐pressure sintering. The influence of SiCw contents on the microstructure and mechanical properties of regenerated WC‐8‐wt% Co cemented carbide was investigated. The results indicated that the hardness, density, flexural strength, and fracture toughness of regenerated cemented carbide first increased and then decreased with the addition of SiCw. The Vickers hardness, density, flexural strength, and fracture toughness could reach 1575 HV, 14.6 g/cm3, 2204 MPa, 16.85 MPa·m1/2, respectively, with SiCw content 0.5 wt%, which were increased by 14.4%, 0.7%, 12.2%, and 17.3%, respectively, when compared with the regenerated cemented carbide without SiCw. The lowest friction coefficient and the best wear resistance could be also reached when 0.5‐wt% SiCw was added. The fracture mechanism of the regenerated cemented carbide contained both transgranular and intergranular fracture through the microscopic observation of fracture surface via scanning electron microscope. [ABSTRACT FROM AUTHOR]

Impurity elements such as Fe, Ni, Zn, and Ca introduced in the recycling process of regenerated cemented carbide affect the structure and mechanical properties of the regenerated cemented carbide. Unlike other impurity elements, Fe and Co belong to group VIII elements and have similar chemical and physical properties. The nature of Fe is closely related to the size and type of waste cemented carbide during recycling and pollution observed during production. Waste cemented carbide is processed via zinc melting to obtain WC, and the regenerated YG10 cemented carbide was prepared via low‐pressure sintering in this study. The effects of impurity element Fe on the microstructure and mechanical properties of a regenerated cemented carbide were studied via X‐ray diffraction, scanning electron microscopy, magnetic property tests, and mechanical property tests. This study demonstrates that an increase in the Fe content leads to a decrease in the bending strength and hardness; further, the mechanism of grain growth caused by the increase in Fe content is revealed. In addition, the mechanism of decreasing wear resistance of the regenerated YG10 cemented carbide with increasing Fe content was discussed. The introduction of Fe as an impurity has evident adverse effects on the mechanical properties of the alloy. To satisfy the production requirements, the Fe content in the mixed powder must to be retained within 0.5%. [ABSTRACT FROM AUTHOR]

The aim of the present study was to develop a liquid chromatography/electrospray ionization tandem mass spectrometry (LC–ESI–MS/MS) method for the determination of olaparib in rat plasma. The plasma samples were processed using one‐step protein precipitation with acetonitrile and then separated on Waters Acquity BEH C18 column (50 × 2.1 mm, particle size 1.7 μm) using water containing 0.1% formic acid and acetonitrile as mobile phase with optimized gradient elution. Mass spectrometric detection was carried out by selective reaction monitoring mode via positive ESI mode with precursor‐to‐product transitions of m/z 435.3 > 367.1 and m/z 443.1 > 375.2 for olaparib and 2H8‐olaparib (internal standard). The method was linear over the concentration range 0.1–2000 ng/ml with correlation coefficient >0.9987. The lower limit of quantitation was 0.1 ng/ml. The method showed excellent accuracy and precision, negligible matrix effect and high extraction recovery. The validated method was subsequently utilized to determine the concentration of olaparib in rat plasma and further applied to the pharmacokinetic study of olaparib in rat plasma. Our results demonstrated that olaparib showed gender‐dependent pharmacokinetics in rats. Compared with that in males, olaparib showed high plasma exposure, long half‐life, low clearance and high bioavailability in females. [ABSTRACT FROM AUTHOR]

This paper investigates the effect of turning process on surface quality and corrosion behaviors of laser cladded coatings on the 1045 steel. Corrosion resistance of the 1045 steel is improved by laser cladded Fe−Cr−Ni coatings. The as‐cladded coating behaves nobler and more resistant to corrosion compared to the 1045 steel substrate. By using turning as a finish process, surface roughness Ra of the laser cladded coating is decreased to 0.517 µm to meet the surface roughness requirement (i.e., Ra ≤ 0.8 µm) of a single‐telescopic hydraulic column. Also, surface defects including laps, cavities, and adhered material particles occur on the cladded coatings after machining. The machined coatings exhibit comparable polarization resistance compared to the as‐cladded condition, and the polarization resistance of the machined surface increases with feed rate increasing. The corrosion pits show sensitivity on feed marks induced by machining. This concentrated distribution of corrosion pits is a result of the fluctuation of local electron work function (EWF), which promotes the formation of local corrosion cells in adjacency to feed marks. [ABSTRACT FROM AUTHOR]

The distribution of Asian ancestry in the genome of Danish Duroc pigs was investigated using whole‐genome sequencing data from European wild boars, Danish Duroc, Chinese Meishan and Bamaxiang pigs. Asian haplotypes deriving from Meishan and Bamaxiang occur widely across the genome. Signatures of selection on Asian haplotypes are common in the genome, but few of these haplotypes have been fixed. By defining 50‐kb windows with more than 50% Chinese ancestry, which did not exhibit extreme genetic differentiation between Meishan and Bamaxiang as candidate regions, the enrichment of quantitative trait loci in candidate regions supports that Asian haplotypes under selection play an important role in contributing genetic variation underlying production, reproduction, meat and carcass, and exterior traits. Gene annotation of regions with the highest proportion of Chinese ancestry revealed genes of biological interest, such as NR6A1. Further haplotype clustering analysis suggested that a haplotype of Chinese origin around the NR6A1 gene was introduced to Europe and then underwent a selective sweep in European pigs. Besides, functional genes in candidate regions, such as AHR and PGRMC2, associated with fertility, and SAL1, associated with meat quality, were identified. Our results demonstrate the contribution of Asian haplotypes to the genomes of European pigs. Findings herein facilitate further genomic studies such as genomewide association study and genomic prediction by providing ancestry information of variants. [ABSTRACT FROM AUTHOR]

Number of inseminations to conception (NINS), an important fertility trait, requires appropriate approaches for genetic evaluation due to its non-normal distribution and censoring records. In this study, we analyzed NINS in 474 837 Danish Holstein cows at their first lactation by using seven models which deal with the categorical phenotypes and censored records in different manners, further assessed these models with regard to stability, lack of bias and accuracy of prediction. The estimated heritability from four models based on original NINS specified as a linear Gaussian model, categorical threshold model, threshold linear model and survival model were similar (0.031-0.037). While for the other three models based on the binary response derived from NINS, referred as threshold model (TM), logistic and probit models (LOGM and PROM), the heritability were estimated as 0.027, 0.063 and 0.027, respectively. The model comparison concluded that different models could lead to slightly different sire rankings in terms of breeding values; a more complicated model led to less stability of prediction; the models based on the binary response derived from NINS (TM, LOGM and PROM) had slightly better performances in terms of unbiased and accurate prediction of breeding values. [ABSTRACT FROM AUTHOR]