Search

For better blast furnace performance, there has always been a need for better quality raw materials like sinter, lump ore, and pellets. Among these raw materials the usage of sinter in blast furnace is at higher side compared to other iron bearing materials. As the quality of sinter product improves, its usage in blast furnaces also increases. Iron ore fines are the main source for sinter making. To improve the sinter properties it is necessary to provide good quality of iron ore fines. Due to depletion of high grade iron ore resources, goethite and limonitic ore content in iron ore fines is expected to increase gradually. Usually limonitic and goethite ore are associated with higher alumina and LOI. The conventional sintering process is one of the well established processes for high quality hematite ore. It does not fully respond to the low grade iron ore associated with goethite and limonite. This has led to deterioration in sinter properties and productivity. In recent years the improvement in the quasi-particle structure with the granulation process is an effective method for improving sinter quality and productivity. To improve the sinter quality and productivity for low grade iron ore fines, different granulation processes like the conventional one, and other two advanced granulation processes like coke breeze, and flux & coke breeze coating granulation were studied in detail by conducting laboratory pot grate sintering experiments. From the test results it was found that sinter productivity, physical and metallurgical properties of the sinter improved with flux & coke breeze coating granulation process compared to conventional and coke breeze coating granulation process. Proper selection of the granulation time is very important to achieve the desired sinter properties. In the present work detailed laboratory experiments have been carried out by varying the coating time from 30s to 110s to study the influence of flux & coke breeze coating granulation time on mineralogy, productivity, physical, and metallurgical properties of sinter. With a coating granulation time of 50s, higher productivity, higher yield, and stronger sinter (higher T.I) with lower RDI and -5mm size sinter were achieved. [ABSTRACT FROM AUTHOR]

Iron ore fluxed sinter is the main ferrous burden of Jindal south west steel limited (JSWSL) blast furnaces. In sinter plant fluxes including limestone and dolomite are added to improve the sinter properties of iron ore and to provide an appropriate slag composition of the blast furnace. The raw material grain size affects the sinter process considerably because the sinter productivity and quality are strongly dependent on the green permeability of the bed, which is determined by the particle size distribution of the raw materials, the granulation effectiveness and by the sintering process itself. It is well-known that in fluxed sinter, the size of limestone affects productivity and physical and metallurgical properties of the sinter. It is therefore necessary to understand the role of limestone particle size on sinter properties and productivity. In the present work laboratory sintering experiments have been carried out with different levels of limestone mean particle size (from 0.14 to 1.83mm) to understand the influence of limestone particle size on mineralogy, productivity, physical and metallurgical properties of the sinter. Sinter productivity increased with increasing limestone mean particle size due to improved sinter bed permeability. Sinter with limestone mean particle size of 1.25 to 1.52 mm yielded better sinter strength and lower RDI compared to sinter with smaller or larger limestone mean particle size. Higher sinter strength is due to better and uniform distribution of limestone particles, and better bed permeability enabled easy assimilation and effective distribution of calcium ferrite phases. The improvement in sinter RDI is due to change in mineralogy of the sinter compared to coarser and finer limestone mean particle size. [ABSTRACT FROM AUTHOR]

The article presents a study on the impact of iron ore pellet size on its properties and microstructure. It cites that pellets properties and microstructure depend on raw material mix proportion. Also, reduction and oxidation process occur under various conditions due to pellet size differences. Pellets size from +eight to -12 mm have good strength with lower reduction degradation index (RDI) which are significantly affected by hematite, magnetite, porosity, pore density and size and slag phase.

The article presents on a study on the effect of alumina in iron ore on sinter properties and productivity in the conventional and selective granulation sintering process. The selective granulation process was used with ore fines of different alumina levels while the conventional granulation process was used with the same levels. It was revealed that increase in alumina levels also increase the pore size and number of pores in both process but the conventional pore shape become more irregular.