Search

Sodium‐ion hybrid capacitors (SIHCs) are considered a prospective alternative to lithium‐ion batteries (LIBs) since there are rich and available sodium reserves. Here, nitrogen‐doped carbon tubes (N‐MJ) derived from metaplexis japonica fluff are prepared by using a facile method of etching and peeling the fluff with urea to prepare a Na+ storage anode. With prominent traits in terms of structure and a high nitrogen content (11.08 %), N‐MJ exhibits exceptional Na+ storage performance with a high reversible capacity (390.9 mAh g−1 at 50 mA g−1) and excellent long‐term circulation (208.1 mAh g−1 after 2650 cycles at 1 A g−1). Systemic kinetic analysis manifests that the extraordinary performance is responsible for the large‐scale capacitance control. Furthermore, the SIHCs assembled by using N‐MJ and activated carbon (AC) presents a maximum energy density of 111.4 Wh kg−1 (at 445.8 W kg−1) and power density of 2455.2 W kg−1 (at 34.1 Wh kg−1). Notably, the developed SIHCs maintain a 100 % capacity retention rate at 1 A g−1 after 5000 cycles. Overall, our work not only provides a good choice for storage Na+ anode materials, but also supplies a feasible method for the recycling of waste biomass. [ABSTRACT FROM AUTHOR]

Molybdenum trioxide (MoO3) has recently aroused intensive interest as a renowned conversion‐type anode of Li‐ion batteries (LIBs). Nevertheless, the inferior rate capability, sluggish reaction kinetics, and fast capacity decay during a long‐term charge/discharge process seriously inhibits large‐scale commercial application. Herein, abundant oxygen vacancies and MXene nanosheets are elaborately introduced into MoO3 nanobelts through hydrazine reduction and electrostatic assembly to accelerate the ionic and electronic diffusion/transport kinetics for LIBs. Benefitting from the accelerated ion diffusion kinetics, enhanced electrical conductivity, and additional active sites induced by oxygen vacancies as well as the robust interfacial contact, the prepared MoO3−x/MXene heterostructure exhibits excellent lithium‐ion storage performances. First‐principles calculations indicate that the adsorption of Li+ ion and the electrical conductivity are significantly enhanced for the MoO3−x/MXene heterostructure. Thus, the composite exhibits high reversible capacity of 1258 mAh g−1 at 0.1 A g−1 for Li‐ion storage and retains 474 mAh g−1 at 10 A g−1, remarkably higher than those of the previously reported MoO3‐based anode materials. More importantly, the composite is fabricated with commercial LiFePO4 into a full LIB, which displays an unparalleled energy density of 330 Wh kg−1. [ABSTRACT FROM AUTHOR]

2D MXene materials have attracted intensive attention in energy storage application. However, MXene usually undergoes serious face‐to‐face restacking and inferior stability, significantly preventing its further commercial application. Herein, to suppress the oxidation and self‐restacking of MXene, an efficient and fast self‐assembly route to prepare a 3D porous oxidation‐resistant MXene/graphene (PMG) composite with the assistance of an in situ sacrificial metallic zinc template is demonstrated. The self‐assembled 3D porous architecture can effectively prevent the oxidation of MXene layers with no evident variation in electrical conductivity in air at room temperature after two months, guaranteeing outstanding electrical conductivity and abundant electrochemical active sites accessible to electrolyte ions. Consequently, the PMG‐5 electrode possesses a striking specific capacitance of 393 F g−1, superb rate performance (32.7% at 10 V s−1), and outstanding cycling stability. Furthermore, the as‐assembled asymmetric supercapacitor possesses a pronounced energy density of 50.8 Wh kg−1 and remarkable cycling stability with a 4.3% deterioration of specific capacitance after 10 000 cycles. This work paves a new avenue to solve the two long‐standing significant challenges of MXene in the future. [ABSTRACT FROM AUTHOR]

Potassium‐ion hybrid capacitors have attracted increasing attention due to good energy density, high power density, and low cost. Ti3C2Tx‐MXene is considered as a promising anode material for K ion storage. However, undesirable stacking issues decrease its exposed area and breeds sluggish K ion transport. Herein, a facile spray‐lyophilization strategy is proposed to construct stacking‐resistant Ti3C2Tx with 3D structures. As‐prepared Ti3C2Tx hollow spheres/tubes present stack resistance, a large specific surface area, and a short ion diffusion pathway. When serving as an anode material, it shows enhanced capacity and thickness‐independent rate performance compared to 2D Ti3C2Tx. After 10 000 cycles, a specific capacity of 122 mAh g−1 is obtained at 1 A g−1. Systematic kinetics analyses demonstrate the significance of concentration polarization on the electrode's rate ability. Furthermore, a 3D Ti3C2Tx‖hierarchical porous activated carbon (HPAC) K‐ion hybrid capacitor is assembled and displays remarkable energy and power densities with energy retention of 100% after 10 000 cycles at 1 A g−1. Following this strategy, other 3D structures from nanosheets can also be obtained, such as 3D Ti3C2Tx microtubes and graphene oxide nanoscrolls. This study provides a viable approach to solve the stacking issues of 2D nanosheets to promote the application of 2D materials. [ABSTRACT FROM AUTHOR]

Developing advanced supercapacitors with both high areal and volumetric energy densities remains challenging. In this work, self‐supported, compact carbon composite electrodes are designed with tunable thickness using 3D printing technology for high‐energy‐density supercapacitors. The 3D carbon composite electrodes are composed of the closely stacked and aligned active carbon/carbon nanotube/reduced graphene oxide (AC/CNT/rGO) composite filaments. The AC microparticles are uniformly embedded in the wrinkled CNT/rGO conductive networks without using polymer binders, which contributes to the formation of abundant open and hierarchical pores. The 3D‐printed ultrathick AC/CNT/rGO composite electrode (ten layers) features high areal and volumetric mass loadings of 56.9 mg cm−2 and 256.3 mg cm−3, respectively. The symmetric cell assembled with the 3D‐printed thin GO separator and ultrathick AC/CNT/rGO electrodes can possess both high areal and volumetric capacitances of 4.56 F cm−2 and 10.28 F cm−3, respectively. Correspondingly, the assembled ultrathick and compact symmetric cell achieves high areal and volumetric energy densities of 0.63 mWh cm−2 and 1.43 mWh cm−3, respectively. The all‐component extrusion‐based 3D printing offers a promising strategy for the fabrication of multiscale and multidimensional structures of various high‐energy‐density electrochemical energy storage devices. The all‐graphene‐oxide (GO)‐based symmetric supercapacitor is assembled with a thin GO separator and compact active carbon/carbon nanotube/reduced graphene oxide composite electrodes with tunable thickness, which are fabricated using the advanced extrusion‐based 3D printing technology. The 3D‐printed ultrathick and compact symmetric supercapacitor with a high mass loading can achieve both high areal and volumetric energy densities. [ABSTRACT FROM AUTHOR]