Search

Stretchable conductive silicone rubber (SR) composites are important in wearable electronic devices and the crosslinking of SR composites is necessary for their applications. But the effect of the crosslinking reaction on the electrical conductivity of SR composites is rarely reported. In this article, the effect of crosslinking reaction on the electrical conductivity of SR composites filled with conductive carbon black, carbon nanotubes, and graphene are studied. The crosslink density of SR composites increases with increasing curing time, but the electrical conductivity decreases sharply at the early stage of crosslinking, especially for SR/conductive carbon black composite, which is ascribed to the reaggregation of conductive nanofillers in SR during the crosslinking process. The elastic modulus of the three SR composites gradually increases while the elongation at break decreases with increasing curing time, and the SR/carbon black composite shows ultra‐high elongation at break (1578%). In addition, SR/graphene composite is more sensitive to the extension strain than SR/carbon black and SR/carbon nanotubes composites, and its gauge factor is 414 at the strain ranges of 3–25%. This research work brings a new method to optimize the crosslinking structure of conductive SR composites. [ABSTRACT FROM AUTHOR]

Although direct formic acid fuel cells and direct methanol fuel cells have attracted a lot of interest owing to their high energy‐conversion efficiency and low pollutant emissions, their large‐scale commercial applicability is limited by lack of suitable catalysts that exhibit high activity and are cheap. Here, a synergistic morphology and defect engineering strategy for the "clean" synthesis of multiple‐twinned Pd nanoparticles on nitrogen‐doped low‐defect graphitic carbon nanosheets (Pd/NL‐GCN) without using a template or surfactant are presented. The unique grain‐boundary‐enriched multiple‐twinned Pd nanoparticles provide a large number of catalytically active sites, while the graphitic carbon frameworks with a modulated electronic structure afford high electron conductivity as well as strong poison tolerance. Consequently, the Pd/NL‐GCN hybrid shows outstanding catalytic performance with respect to the oxidation of formic acid and methanol, exhibiting a large electrochemically active surface area, high mass activity, and good long‐term durability. Moreover, the catalyst outperforms conventional Pd‐nanoparticle‐based catalysts supported on carbon black, carbon nanotubes, and graphene materials. [ABSTRACT FROM AUTHOR]

An 'abiotic' biofuel cell composed of catalytic electrodes modified with inorganic nanostructured species was used to activate a pacemaker. The catalytic nanoparticles of various compositions, Au xPt y, deposited on carbon black (CB) were prepared and extensively characterized to select the species with selectivity for glucose oxidation and oxygen reduction. Then two kinds of 3D-electrode materials with different morphology, buckypaper composed of carbon nanotubes (ca. 50 nm diameter) and carbon paper made of carbon fibers (ca. 7 µm diameter), were used in a combination with different catalytic species. Finally, Au/CB nanospecies deposited on buckypaper were selected for catalyzing glucose oxidation (composing the biofuel cell anode) and Au60Pt40/CB species deposited on carbon paper were selected for catalyzing oxygen reduction (composing the biofuel cell cathode). The catalytic electrodes were characterized by cyclic voltammetry in an aqueous buffer solution and the polarization function for the biofuel cell was studied in a human serum solution. The open circuit voltage, Voc, short circuit current density, jsc, and maximum power produced by the biofuel cell, Pma x, were found as 0.35 V, 0.65 mA cm−2 and 104 µW, respectively (in human serum at 5.4 mM glucose). The biofuel cell produced the steady state open circuit voltage over 10 hours with its slow decrease over 50 hours originating from the glucose depletion and slow mass-transport within the 3D-electrode. The voltage produced by the biofuel cell was amplified with an energy harvesting circuit and applied to a pacemaker resulting in its proper operation. The present study continues the research line where different implantable (enzyme-based or abiotic) biofuel cells are used for the activation of biomedical electronic devices, e.g., pacemakers. [ABSTRACT FROM AUTHOR]

Herein, we examine the influence of adding functionalized graphene (FG), distinct expanded graphites and carbon nanofillers such as carbon black and multiwall carbon nanotubes on mechanical properties, morphology, pyrolysis, response to small flame and burning behavior of a V-2 classified flame-retarded polypropylene (PP). Among carbon fillers, FG and multilayer graphene (MLG) containing fewer than 10 layers are very effectively dispersed during twin-screw extrusion and account for enhanced matrix reinforcement. In contrast to the other fillers, no large agglomerates are detected for PP-FR/FG and PP-FR/MLG, as verified by electron microscopy. Adding FG to flame-retardant PP prevents dripping due to reduced flow at low shear rates and shifts the onset of thermal decomposition to temperatures 40°C higher. The increase in the onset temperature correlates with the increasing specific surface areas (BET) of the layered carbon fillers. The reduction of the peak heat release rate by 76% is attributed to the formation of effective protection layers during combustion. The addition of layered carbon nanoparticles lowers the time to ignition. The presence of carbon does not change the composition of the evolved pyrolysis gases, as determined by thermogravimetric analysis combined with online Fourier-transformed infrared measurements. FG and well-exfoliated MLG are superior additives with respect to spherical and tubular carbon nanomaterials. Copyright © 2013 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]