Search

Abstract Antenna chambers are RF‐shielded enclosures which are required for antenna and radio performance measurements. Typically, anechoic chambers (ACs) are used for measuring directional metrics (e.g. antenna pattern, effective isotropic power etc.), while reverberation chambers (RCs) are widely used for non‐directional measurements (e.g. antenna efficiency, total radiated power etc.). When a device under test requires both types of measurements, testing needs to be conducted sequentially in an AC and an RC. This leads to significant time inefficiencies due to the need to set up and calibrate two separate measurement setups in two different chambers. To address these issues, this letter proposes a programmable chamber framework capable of electronically switching between AC and RC modes by programming the reflective intelligent surface‐enabled sidewalls. This framework is highly attractive for the industry as it supports both directional and non‐directional measurements within a single chamber. The letter outlines the conceptual framework, discusses design considerations, and presents preliminary experimental validation of reflective intelligent surface‐enabled sidewall with the designed phase‐setting configurations to emulate the radio absorber sidewall of an AC and the metal plate sidewall of an RC. The experimental results demonstrate the effectiveness and potential of the proposed approach.

Abstract Ever‐increasing bandwidth requirements from various industries drive the need for the ever‐increasing bandwidth of antennas used for testing. Broadband Double‐Ridged Guide Horn (DRGH) antennas are used extensively in antenna measurement and ElectroMagnetic Compatibility/Interference (EMC/I) testing. The current state‐of‐the‐art broadband DRGH antennas reported in the literature for use in measurement applications cover bandwidth ratios as large as 36:1 (0.5–18 GHz). This paper presents the design and realisation of a DRGH antenna with a 100:1 bandwidth ratio (0.5–50 GHz). To achieve such a wide bandwidth, the ridge gap, width and feed were optimised, and a novel coaxial‐to‐ridge waveguide launcher section based on a typical Vivaldi antenna was developed. Backward radiation was reduced using an absorber‐filled cavity. A prototype DRGH antenna was manufactured using additive manufacturing, also referred to as 3D printing. Simulated and measured results obtained in an anechoic chamber are presented.

Abstract Automotive antennas are gaining importance due to their increasingly important role for autonomous driving with the development of the Internet of Vehicles. However, over‐the‐air testing on automotive antennas is difficult owing to its large volume and complex body structure. Plane wave generators can approximate uniform plane waves in the near field of the device under test, which can greatly reduce the measurement distance and thereby decreasing the cost compared with direct far‐field solutions. This letter designs three plane wave generators for three quiet zone sizes selected according to the vehicle structure at 5.9 GHz, achieving quiet zone sizes of 1.45 m ×0.23 m, 2.9m ×0.56 m, and 3.9 m ×1.27 m, respectively. Within the three quiet zones, amplitude deviations of 0.82, 0.34, and 0.34 dB and phase deviations of 9.4∘, 6.72∘ and 1.42∘ are realized, respectively, according to the numerical simulations. Uncertainty analysis is further implemented to investigate the robustness of the designed PWGs proposed in this letter.

Abstract The integration of directive elements into a circular switched parasitic array at 868 MHz is presented. The typical usage of reflective parasitic monopoles is supplemented with additional, shorter monopole elements which are positioned closer to the central active monopole to induce directive behaviour. This allows for more degrees of freedom with the steering of the antennas beam and to increase the gain of the antenna. This leads to a greater flexibility of the system and enables power reduction of the amplifiers for enhanced battery life time. The design and configuration of a circular switched parasitic array with directive elements is shown and a prototype is built for validation.

Abstract Since the total number of the antenna elements can be up to hundreds in a massive multiple‐input multiple‐output (MIMO) system, subarray‐structured base station (BS) array configurations are widely adopted to achieve a good cell coverage and to reduce the required number of radio frequency chains at the same time. It is crucial for any BS product to ensure that the antenna elements perform correctly as expected. Therefore, the necessity of array diagnosis is evident, especially for large BS arrays. Furthermore, it is essential that the diagnosis can be achieved in a compact and cost‐effective setup with high measurement efficiency (i.e. only a few measurement samples are required). The principle of the diagnosis method presented in this article is to obtain the S‐parameters between the subarrays and the probe via solving linear equations. In the simulation, a BS array composed of 16 subarrays with each containing 3 elements is used to validate the diagnosis method at 3.5 GHz. An array composed of 4 subarrays with each containing 3 elements was used in the measurements to verify the diagnosis method with two different phase tuning matrices at 3 GHz. Successful diagnosis results have been achieved in both the simulations and the measurements.

Abstract An effective, probe‐compensated, phaseless Near‐Field‐Far‐Field (NF–FF) transformation technique with planar spiral scanning is presented. The phase retrieval problem is solved by a quadratic inverse process, whose data are the voltage squared amplitudes of the NF samples acquired on two scanning surfaces. The available information on the antenna under test and on the scanning geometry are used to provide efficient representations for both the unknowns and the data, thus improving the accuracy and reliability of the technique. Furthermore, disconnected apertures are dealt with by adopting two different sets of prolate spheroidal wave functions to represent the aperture fields. Experimental results are reported to assess the effectiveness of the proposed approach. A drastic reduction (about 90%) of the required NF samples, as compared to standard λ/4 measurements (λ being the wavelength), is observed. Aggregating the measurements on the two scanning surfaces, the technique uses less samples even when compared to the case of complex, λ/2 measurements performed on a single surface. Our approach exhibits an accuracy comparable to that achieved when adopting complex measurements with non‐redundant sampling or classical, λ/2 plane‐rectangular NF–FF transformations.

Abstract This letter presents a comprehensive analysis of the radiation behaviour exhibited by nine distinct on‐wafer radio‐freqeuncy (RF) probes used for device characterization in the mm‐wave bands of integrated circuits and antennas. The tested probes are sourced from two different manufacturers and feature various probe pitches. All probes are intended for use with the WR‐3.4 waveguide band ranging from 220 to 330 GHz. To the best of the authors' knowledge, such a detailed examination of RF probes operating in this band with respect to their radiation behaviour has not been demonstrated before.

Abstract In millimetre wave (mmWave) frequency band, radio resource management (RRM) performance is characterised in plane wave conditions using radiated over‐the‐air test method, which is a challenging combination of protocol and radio frequency performance measurement. This article presents a novel design of multiple lens‐based compact antenna test ranges (CATRs) to simulate multiple angles of arrival from different base‐stations in RRM measurement. Only four lens‐based CATRs are proposed to create plane wave conditions at the device under test with six different angles of arrival and capable of accurately constructing the wireless propagation condition and minimising the diffraction and scattering between adjacent CATRs. The lens‐based CATR is the key element in the RRM measurement system, which is composed of a metasurface lens for phase alignment and a 2 × 2 feed array antenna for the emission of electromagnetic signals. The function and capability of the proposed lens‐based CATR is validated through simulation and measurement, that the worst‐case amplitude variation in the quiet zone region is lower than ±0.8 dB at 26 GHz, and phase variation is lower than ±7.5° in the designed quiet zone, which could be used in the fifth‐generation mmWave RRM measurement.

The classic method of testing array antenna is measuring the beam pattern separately, which suffers from low efficiency. In this study, a fast measurement method used for received array antenna has been present. Firstly, the patterns of element antennas have been tested using multi-channel receiver. Then the entire pattern could be computed by weighting the information of elements. The information contains amplitude and phase, which could be obtained by theory or measurement.