Search

OBJECTIVE To systematically evaluate the effect of microwave disinfection on the dimensional stability of denture base acrylic resins. BACKGROUND Microwave disinfection has been considered as an alternative method for disinfecting complete dentures to help prevent and treat denture stomatitis. However, data on the impact of microwave disinfection on the dimensional stability of acrylic resins are still scarce. METHODS The PubMed/Medline, SCOPUS and EMBASE databases were searched in order to assess articles published in English up to January 2021 (CRD42021212267). We included studies that have assessed the effect of microwave disinfection, on the dimensional stability of acrylic resins, comparing them with negative or positive controls. RESULTS A total of seven in vitro studies were included. The qualitative synthesis demonstrated that, in general, microwave disinfection produced more distortion on the materials than do immersion in sodium hypochlorite, chloride solution, chlorhexidine, and water immersion. However, considering the dimensional stability of the specimens, microwave disinfection at 500 W for 3 minutes, and at 450 W for 5 minutes, produced similar or better outcomes than did control groups. CONCLUSION In general, microwave disinfection promotes changes in the dimensional stability of denture base acrylic resins, and should thus be used with caution. However, microwave disinfection protocols at lower power settings (500 and 450 W) and exposure times (3 and 5 minutes) produces similar or less distortion than chemical disinfection. More studies are still required in order to evaluate the clinical and long-term implications of microwave disinfection.

Purpose This study aimed to evaluate the repair strength of a newly introduced repair technique involving zero-gap repair width. Materials and methods A total of 36 rectangular prism specimens with dimensions of 64 × 10 × 3.3 mm were prepared from heat-polymerized acrylic resin. Nine specimens were kept intact. The other specimens were sectioned into halves and modified to create repair gaps of 2.5-mm beveled (2.5B) as control, 0-mm beveled (ZB), and 0-mm inverse bi-beveled (ZIBB). The ZIBB group was prepared with a V-shaped internal groove on both halves (repair tunnel), while the intaglio and cameo surfaces were kept intact except for two small holes at the cameo surface for repair resin injection. The 2.5B and ZB groups were repaired conventionally while the ZIBB group was repaired by injecting repair resin into the tunnel through one of the holes until excess material oozed from the other hole. Repaired specimens were thermally cycled at 5 and 55°C for 10,000 cycles with 1 min dwell time. A 3-point bending test was conducted using a universal testing machine for flexural strength and elastic modulus measurement. Kruskal-Wallis/Mann-Whitney tests and ANOVA/post hoc Tukey tests were applied for data analysis (α = 0.05). Results The flexural strength of repaired specimens was substantially lower than that of intact specimens, and significant differences were present between repaired groups (p ˂ 0.05). ZB and ZIBB had higher flexural strength (p ˂ 0.001) and elastic modulus (p ˂ 0.05) than 2.5B. Among the ZB and ZIBB groups, ZB showed the highest flexural strength, and ZIBB had the highest elastic modulus. Conclusion The closed repair technique improved the flexural strength and elastic modulus of repaired acrylic denture base.

Background Candida biofilm is a major cause of denture stomatitis. We aimed to compare the efficacy of low-molecular-weight chitosan solutions against Candida albicans biofilm on polymethyl methacrylate (PMMA) resin. Methods Various types of chitosan were tested for anti-Candida activity by broth dilution. Two types were selected for further testing on 24-hour C.albicans biofilm formed on PMMA specimens. Specimens were randomly distributed among experimental groups, including 0.1% and 0.2% acetic acid, 3 and 6 mg/mL of oligomer chitosan and 30 kDa chitosan solutions, effervescent tablet (Polident), and 0.2% chlorhexidine, and immersed for 5 min to 12 h. The viability of C. albicans after cleansing were determined by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assays. Remaining viability was calculated into percentage relative to respective controls and analyzed using ANOVA with Tukey post-hoc tests. Live/dead fluorescence microscopy was also performed. Results Chitosan solutions had high efficacy against C. albicans biofilm on PMMA. The mean relative viability compared to control after 12-h immersion was 6.60 ± 4.75% and 12.72 ± 6.96% for 3 and 6 mg/mL oligomer, respectively, and 11.68 ± 4.81% and 18.08 ± 6.20% for 3 and 6 mg/mL 30 kDa chitosan, respectively. Conclusions Low-molecular-weight chitosan solution is an effective antifungal denture cleanser that can significantly reduce C. albicans viability in biofilm on PMMA.

Background The purpose of this study was to compare the displacement of tooth arrangement in dentures fabricated by additive manufacturing (AM) and heat curing. Methods Three-dimensional (3D) scanning was performed for edentulous jaw models. After the teeth were arranged, 3D scanning for the wax denture was performed. Heat-cured dentures were fabricated with heat-cure polymer resin. Based on data obtained by subtracting the model data from wax denture data, AM dentures were fabricated from ultraviolet-cured acrylic resin. Accuracy was verified by superimposing heat-cured and AM dentures on the tooth region data from the wax dentures and measuring displacement of the tooth arrangement. Results In the maxillary dentures, the amount of tooth displacement for the heat-cured dentures and for the AM dentures ranged from -0.08 to +0.06 mm and from -0.25 to +0.06 mm respectively. A significant difference was observed between two dentures. In the mandibular dentures, the amount of tooth displacement for the heat-cured dentures and for the AM dentures ranged from -0.09 to +0.07 mm and from -0.03 to +0.07 mm respectively. No significant difference was observed between two dentures. Conclusions The artificial teeth of the maxillary dentures fabricated by AM showed a greater displacement compared to those by heat curing.

OBJECTIVE This study aimed to systematically review the literature regarding the surface roughness of polymethylmethacrylate (PMMA) for denture bases, disinfected with different chemical agents and analyse the outcomes of the included studies. BACKGROUND Various chemical disinfection protocols to clean the removable dental prosthesis are reported in the literature, however systematic reviews analysing the outcomes in the surface roughness of the PMMA are lacking. METHODS The Preferred Reporting Items for Systematic Review and Meta-Analyses (PRISMA) checklist was used to structure this systematic review. The inclusion criteria were as follows: clinical trials, in vitro studies, studies in English and studies comparing the effects of chemical disinfection products on the surface roughness of PMMA. An electronic search was performed in the following databases: PubMed/MEDLINE, Scopus and Web of Science.; we also conducted a manual search for articles published in specific journals of dental prostheses and dental materials. RESULTS Thirteen in vitro studies in this systematic review and meta-analysis. According to the meta-analysis, the effects of 0.5% (P = .32; MD: 0.06; CI: -0.05 to 0.17; heterogeneity: P

Purpose To evaluate the fatigue survival, fracture loads and failure modes of monolithic lithium disilicate screw-retained crowns, attached to titanium insert, and cement-retained crowns. Materials and methods Internal tapered connection implants, embedded in acrylic resin at 30° inclination, were restored with lithium disilicate restorations, simulating a maxillary premolar (n = 20), with different designs: screw-retained titanium base abutment-crowns, and cement-retained crowns. The specimens were submitted to cyclic mechanical loading (1.2 × 106 cycles with a load of 0-250 N at 2 Hz). Surviving specimens were subjected to single load to fracture in a universal testing machine and failure modes were determined with the aid of an optical microscope. Maximum load values were analyzed statistically using the t-test and differences in failure modes were analyzed using the chi-squared test (α = 0.05). Results All specimens survived the cyclic mechanical loading. Fracture load was significantly higher for screw-retained crowns (821.69 ±196.71 N) than the cement-retained crowns (577.03 ± 137.75 N) (p = 0.005). Ceramic failure was the predominant mode, with no statistical difference between groups. Conclusions Screw-retained and cement-retained lithium disilicate crowns survived the cyclic mechanical loading. The use of titanium inserts to support a monolithic restoration enhances the fracture strength of the crown/abutment system.

Background There is insufficient evidence for the efficacy of silicone soft reliner on the obturator prosthesis after maxillectomy for oral malignant tumors. Objective To verify the efficacy of silicone soft reliner on the obturator prosthesis after maxillectomy, by evaluating masticatory performance and quality of life (QoL). Methods This was a single‐arm prospective interventional study, verifying the efficacy of silicone soft reliner (GC RELINE II®) on the maxillary obturator prosthesis. Data were obtained from a comparison of the endpoints after 14 days of continuous use of acrylic and silicone soft‐lined prostheses. The primary endpoint was masticatory performance. The secondary endpoints were occlusal performance and oral health‐related QoL (OHRQoL). The masticatory performance, occlusal performance, and OHRQoL were assessed by glucose concentration, maximum bite force, and the Japanese version of Oral Health Impact Profile (OHIP‐J49), respectively. Results This study included five patients (two males, three females), aged between 71 and 88 years, with a median of 74 years. The median of glucose concentration indicated a statistically significant improvement between the acrylic resin (99.6 mg/dL) and silicone soft reliner (126.0 mg/dL) obturator prosthesis (p = .043). There was no significant difference in the median of maximum bite force between the acrylic resin (302.0 N) and silicone soft reliner (250.0 N) obturator prosthesis (p = .893). Functional limitations domain of the OHIP‐J49 indicated a statistically significant improvement between the acrylic resin and silicone soft reliner obturator prosthesis (p = .043). Conclusions This study indicated that an obturator relined with soft silicone improved masticatory performance and the OHRQoL post‐maxillectomy.

PURPOSE: The additions of zirconium oxide nanoparticles (nano-ZrO2 ) to denture base materials have produced nanocomposites with satisfactory properties, although there is a lack of research investigating the effects of denture cleansers on these materials. This study aimed to evaluate the effect of denture cleansers on the flexural strength of denture base materials modified with nano-ZrO2 . MATERIALS AND METHODS: A total of 270 specimens were fabricated from pure and nano-ZrO2 reinforced acrylic resins at 2.5% and 5%, resulting in 3 main groups. The groups were further divided into subgroups (n=10) according to immersion solution (distilled water, Corega, sodium hypochlorite, and Renew) and immersion duration. Flexural strength was measured at baseline (T0 ) in distilled water and after 180 and 365 days of immersion (T1 and T2 ) in denture cleansers. Data were collected and analyzed using repeated measure ANOVA and Bonferroni post hoc tests (α=0.05). RESULTS: The flexural strength of the nano-ZrO2 modified denture base material decreased significantly after immersion in different denture cleansers at different immersion durations in comparison to baseline (T0 ) (P

PURPOSE To evaluate the effect of protective coatings on the surface roughness, contact angle, and Candida albicans (C. albicans) adhesion to polymethyl methacrylate (PMMA) denture base materials. MATERIAL AND METHODS A total of 560 rectangular heat- and autopolymerized acrylic resin specimens were fabricated and divided into 5 groups (n = 14/group) according to coating agent. Uncoated specimens were used as control. Coating materials were: nano-coat, Optiglaze, nano-silica, or cyanoacrylate. Surface roughness (Ra ) was evaluated using a profilometer. Contact angle measurements were performed using the sessile drop method. C. albicans adhesion was evaluated using direct culture and slide count methods. ANOVA and Tukey's post hoc tests were used for data analysis (α = 0.05). RESULTS Nano-coat and Optiglaze coating of heat-polymerized acrylic significantly decreased Ra (p < 0.001). No significant effect was seen with nano-silica coating while Ra significantly increased with cyanoacrylate (p < 0.001). For autopolymerized acrylic, nano-coat, Optiglaze, and nano-silica coatings significantly decreased Ra in comparison to control group (p < 0.001) while no significant difference was seen between control and cyanoacrylate coating (p = 0.45). In comparison to control group, nano-coat, Optiglaze, and nano-silica coating for both denture base materials significantly decreased contact angle, and C. albicans adhesion (p < 0.001) while cyanoacrylate significantly increased C. albicans adhesion (p = 0.002) with no effect on contact angle for heat- (p = 1.00) and autopolymerized resins (p = 0.83). CONCLUSION Coating of removable prosthesis with nano-coat, Optiglaze, or nano-silica is an effective method to reduce C. albicans adhesion.

PURPOSE To evaluate and compare the effects of glass fiber (GF), Zirconium oxide nanoparticles (nano-ZrO2 ), and silicon dioxide nanoparticles (nano-SiO2 ) addition on the flexural strength and impact strength of repaired denture base material. MATERIALS AND METHODS Heat-polymerized acrylic resin specimens were fabricated. All specimens were sectioned centrally and beveled creating 2.5 mm repair gap except for 10 controls. Specimen grouping (n = 10/group) was done according to filler concentration of 0%, 0.25%, 0.5%, and 0.75% of auto-polymerized acrylic powder. Modified resin was mixed, packed in the repair gap, polymerized, finished and polished. Three-point bending test and Charpy type impact testing were done. Data were analyzed using one-way-ANOVA and Post-Hoc Tukey test (α = 0.05). RESULTS All additives significantly increased flexural strength and impact strength (p < 0.05). Within the modified subgroups, no significant differences were found for GF. Significant increase for nano-ZrO2 and significant decrease for nano-SiO2 as the concentration of additive increased were noted for both flexural strength and impact strength. Highest flexural strength was found with 0.75%-nano-ZrO2 (69.59 ± 2.52MPa) and the lowest was found with 0.75%-nano-SiO2 (53.82 ± 3.10MPa). The 0.25%-nano-SiO2 showed the highest impact strength value (2.54 ± 0.21 kJ/m2 ) while the lowest impact strength value was seen with 0.75%-nano-SiO2 (1.54 ± 0.17 kJ/m2 ). CONCLUSION Nano-filler effect was concentration dependent and its addition to repair resin increased the flexural and impact strengths. The incorporation of 0.75%-ZrO2 or 0.25%-SiO2 into repair resin proved to be a promising technique to enhance repair strength and avoid repeated fractures.

PURPOSE To investigate the influence of nonthermal plasma (NTP) treatment on the tensile bond strength between heat-polymerized acrylic resin for ocular prostheses and silicone reliner, with and without the use of an adhesive primer. MATERIALS AND METHODS One-hundred and sixty-four acrylic resin specimens were fabricated and randomly distributed into four groups according to the type of surface treatment: Sofreliner Primer, NTP, Sofreliner Primer + NTP, and NTP + Sofreliner Primer. Two specimens interposed with relining material (Sofreliner) formed one test sample to perform the tensile bond strength tests, before (initial) and after storage (final) in saline solution (37°C, 90 days, n = 10). Surface characterization was performed by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The failure type was classified as cohesive, adhesive, or mixed. The data were analyzed statistically using the two-way ANOVA and Tukey test, as well as the chi-squared test (α = 0.05), Bonferroni correction (α = 0.005), and Spearman correlation coefficient (α = 0.05). RESULTS The SEM and EDS analyses showed the presence of a thin, homogenous organic film in the groups treated with NTP. The NTP + Sofreliner Primer group presented the largest bond strength mean values in the initial period (p < 0.05). Sofreliner Primer and NTP + Sofreliner Primer groups presented the first and second largest tensile bond strength mean values in the final period (p < 0.05), respectively. NTP + Sofreliner Primer group also had the largest number of cohesive (70%, initial) and mixed (90%, final) failures. CONCLUSIONS The NTP treatment performed before the primer application enhanced the bond between the acrylic resin ocular prosthesis and the Sofreliner silicone-based reliner, even after 90 days of immersion in saline solution.

Purpose To evaluate the effect of the addition of low concentration of silicon-dioxide nanoparticles (nano-SiO2 ) to poly(methylmethacrylate) (PMMA) denture base material on Candida albicans adhesion, surface roughness, contact angle, hardness, and translucency. Materials and methods A total of 150 acrylic disks were fabricated from heat-polymerized acrylic resin and specimens were divided into 3 groups of 50 per test. They were further subdivided into 5 subgroups (n = 10) according to the concentration of nano-SiO2 : control (no addition) and four tested groups modified with 0.05, 0.25, 0.5, and 1.0 wt% nano-SiO2 of acrylic powder. Slide count and direct culture methods were used to measure C. albicans count (CFU/mL). The surface roughness values (Ra ; μm) were determined using a profilometer. The contact angle (o ) measurement was performed by a goniometer using the sessile drop method. Vickers hardness was used to analyze surface hardness. Translucency was measured using a spectrophotometer. Data analysis was conducted through analysis of variance and Tukey's post hoc tests (α = 0.05). Results Compared to the control group, direct culture and slide count methods illustrated a significant decrease in C. albicans count (p ˂ 0.001) with the addition of nano-SiO2 , and this decrease was correlated with the concentration of nano-SiO2 . The addition of nano-SiO2 significantly decreased the contact angle (p ˂ 0.001), whereas hardness and surface roughness significantly increased (p ˂ 0.001). The addition of nano-SiO2 significantly decreased translucency (p ˂ 0.001), and this decrease was concentration dependent. Conclusion Addition of low concentration of nano-SiO2 decreased C. albicans adhesion to PMMA denture base resin. Also, low additions of nano-SiO2 have positive effects on contact angle and hardness, whereas surface roughness and translucency were adversely affected at high concentrations.

PURPOSE Metal removable partial dentures (RPDs) are often considered long-term treatment options for partially edentulous patients, while acrylic resin RPDs are considered interim treatments. The aim of this review was to compare metal and acrylic resin RPDs regarding patient-reported outcomes for partially edentulous individuals. MATERIALS AND METHODS Four databases (MEDLINE, EMBASE, CENTRAL, and Web of Science) were systematically searched for observational studies and randomized controlled trials comparing patient-reported outcomes between metal and acrylic resin RPDs. The primary outcome was patient satisfaction. Included studies were assessed for risk of bias using the Cochrane risk of bias in nonrandomized studies of interventions tool (ROBINS-I) and the Cochrane Collaboration Risk of Bias Tool for Randomized Controlled Trials. The level of evidence was evaluated using Oxford Center for Evidence-based Medicine tool. A random-effects model was used to analyze the data. RESULTS A total of 15 studies were included in the systematic review; 10 in the meta-analysis. The pooled effect size for patient satisfaction and oral health-related quality of life showed no statistical significant difference between metal and acrylic resin dentures (0.22, 95% confidence interval -0.01, 0.45, p = 0.06; 1.45, 95% confidence interval -2.43, 5.33, p = 0.46, respectively). Compliance with using RPDs was significantly higher in patients with metal compared to patients with acrylic resin dentures (pooled odds ratio = 0.57, 95% confidence interval 0.45, 0.73, p < 0.001). Most studies had critical to serious risk of bias and low level of evidence. CONCLUSIONS The reviewed studies showed that there was no significant difference between metal and acrylic resin RPDs in patient satisfaction and oral health-related quality of life. Metal dentures were associated with higher patient compliance rates and were preferred more by patients compared to acrylic resin dentures. However, the reviewed studies had low levels of evidence and therefore, high-quality randomized controlled trials are needed to conclusively address the question of this review.

Purpose To assess the effect of addition of different concentrations of nanodiamonds (NDs) on flexural strength, impact strength, and surface roughness of heat-polymerized acrylic resin. Materials and methods 120 specimens were fabricated from heat-polymerized acrylic resin. They were divided into a control group of pure polymethylmethacrylate (PMMA; Major.Base.20) and three tested groups (PMMA-ND) with 0.5%wt, 1%wt, and 1.5%wt of added ND to PMMA. Flexural strength was determined using the three-point bending test. Impact strength was recorded by using a Charpy type impact test. Surface roughness test was performed using a Contour GT machine. One-way ANOVA and Tukey's post-hoc analysis (p ≤ 0.05) were used for statistical analysis. Results Acrylic resin reinforced with 0.5% ND displayed significantly higher flexural strength than the unreinforced heat-polymerized specimens, acrylic resin reinforced with 1% ND and the 1.5% ND (p 0.05). The addition of 0.5% ND and 1% ND significantly decreased the surface roughness in comparison to both control and the 1.5% ND groups (p 0.05) were reported. Nano-composite material (0.5% ND) showed significantly lower surface roughness when compared to other specimens. Conclusions The addition of NDs to acrylic denture base improved the flexural strength and surface roughness at low concentrations (0.5%), while the impact strength was decreased with ND addition.

Objective The aim of this study was to evaluate surface changes on dental implant systems and ions release after immersion in fluoride and hydrogen peroxide. Methods Ten implant-abutment assemblies were embedded in acrylic resin and cross-sectioned along the implant vertical axis. Samples were wet ground and polished. Delimited areas of groups of samples were immersed in 1.23% sodium fluoride gel (F) or in 35% hydrogen peroxide (HP) for 16 min. Gels (n = 3) were collected from the implant surfaces and analyzed by inductively coupled plasma mass spectrometry (ICP-MS), to detect the concentration of metallic ions released from the implant systems. Selected areas of the abutment and implant (n = 15) were analyzed by atomic force microscopy (AFM) and scanning electron microscopy (SEM). Results SEM images revealed surface topographic changes on implant-abutment joints after immersion in fluoride. Implants showed excessive oxidation within loss of material, while abutment surfaces revealed intergranular corrosion after immersion in fluoride. ICP-MS results revealed a high concentration of Ti, Al, V ions in fluoride after contact with the implant systems. Localized corrosion of implant systems could not be detected by SEM after immersion in hydrogen peroxide although the profilometry showed increase in roughness. ICP-MS showed the release of metallic ions in hydrogen peroxide medium after contact with dental implants. Conclusion Therapeutical substances such as fluorides and hydrogen peroxide can promote the degradation of titanium-based dental implant and abutments leading to the release of toxic ions.

PURPOSE To evaluate the effect of addition of different concentrations of thymoquinone (TQ) on the flexural strength, elastic modulus, surface roughness, and hardness of PMMA denture base material. MATERIALS AND METHODS A total of 160 rectangular specimens were prepared from heat-polymerized acrylic resin, with dimensions of 65 × 10 × 2.5 mm3 for flexural strength testing and 10 × 20 × 3 mm3 for surface property testing. The specimens were divided into eight groups of 20 specimens: one control group without addition of TQ and seven test groups prepared by adding TQ to acrylic powder in concentrations of 0.5, 1, 1.5, 2, 2.5, 3, and 5 wt%. The polymer was added to the monomer before being mixed, packed, and processed using the conventional water bath method. A universal testing machine was used to measure flexural strength and elastic modulus. A profilometer and a Vickers hardness tester were used to measure surface roughness and hardness, respectively. One-way ANOVA and the Tukey-Kramer multiple-comparison test were used for statistical analysis, with statistical significance at p ≤ 0.05. RESULTS Addition of TQ to PMMA denture base material significantly decreased flexural strength and elastic modulus at high concentrations (p < 0.01), while no significant differences were observed at low concentrations (0.5%, 1% TQ) in comparison with the control group. At high TQ concentrations, surface roughness increased while hardness decreased (p < 0.0001), and no significant differences were observed at low concentrations (0.5%, 1% TQ) in comparison with the control group. The most favorable addition values were 0.5% and 1% TQ in all TQ groups. CONCLUSIONS Addition of TQ did not affect the flexural and surface properties of PMMA denture base material at low concentrations (0.5%, 1% TQ) and could be incorporated into PMMA denture base material as an antifungal agent.

Background More research is needed on the study of new materials for fixed prosthetic implant-supported rehabilitations. Purpose The purpose of this study was to report the short-term outcome of full-arch implant-supported fixed hybrid polyetheretherketone (PEEK)-acrylic resin prostheses and the all-on-four concept. Materials and methods This prospective cohort clinical study included 37 patients (29 women, eight men) with an average age of 60 years (range: 38-78 years) with 49 full-arch hybrid PEEK-acrylic resin prosthesis supported by implants through the all-on-four concept. Primary outcome measures were prosthetic survival. Results Two patients with two maxillary prostheses were lost to follow-up. One patient with a double full-arch rehabilitation fractured the mandibular PEEK framework, rendering a 98% prosthetic survival rate. No implants were lost. The average (SD) marginal bone remodeling after 1 year of follow-up was 0.37 mm (0.58 mm). Technical complications concerning the veneer adhesion occurred in six patients and were resolved in all patients (with exception of the patient with prosthetic failure) through the creation of mechanical retentions and changing the bonding primer. Mechanical complications occurred in three patients and five prostheses consisting in prosthetic screw loosening (n = 2 patients) and fracture of the acrylic resin teeth (the patient with a prosthetic failure). Conclusions Within the limitations of this study, the results suggest that hybrid polymer (PEEK)-acrylic resin prostheses supported by implants for full-arch rehabilitation may represent a valid treatment option, still requiring longer-term validation.

Background This study aimed to fabricate a denture base resin (DBR) containing phytoncide microcapsules (PTMCs) and determine the mechanical properties of the resin and antifungal activity. Methods Fifty‐four heat cured rectangular DBR specimens (64 x 10 x 3.3 ± 0.2 mm) containing nine concentrations of PTMC between 0 ‐ 5% (wt/wt) were fabricated and subjected to a three‐point bending test. A phytoncide release bioassay was developed using DBR containing 0% and 2.5% PTMCs (wt/wt) in a 24 well‐plate assay with incubation of Porphyromonas gingivalis at 37°C for 74 h. The antifungal activity of PTMCs against Candida albicans, in a pH 5.5 acidic environment was determined in a plate assay. Results Flexural strength decreased with increasing PTMC concentration from 97.58 ± 4.79 MPa for the DBR alone to 53.66 ± 2.46 MPa for DBR containing 5.0% PTMC. No release of phytoncide from the PTMCs in the DBR was detected at pH 7.4. The PTMCs had a minimal inhibitory concentration of 2.6% (wt/vol) against C. albicans at pH 5.5. Conclusions PTMCs can be added to DBR 2.5% (wt/wt) without adversely affecting flexural strength. PTMCs released the antimicrobial agent at pH 5.5 at concentrations sufficient to inhibit the growth of the C. albicans.

PURPOSE To evaluate the pullout resistance of CAD/CAM implant-supported crowns cemented with provisional and definitive cements on Ti-base implant abutments. MATERIALS AND METHODS Sixty crowns were milled for use in Ti-base implant abutments and divided (n = 15/group) according to material, as follows: (a) [Pr] Temporary acrylic resin; (b) [Co-Cr] Cobalt-Chromium alloy; (c) [Zr] polycrystalline zirconia; and (d) [Ti] titanium. The cementation was performed with RelyX Temp NE (RxT) cement or RelyX U200 self-etching resin cement, under a 50 N (5 kg) load for 10 minutes. Twenty-four hours after cementation, the crowns were subjected to the pullout test in a universal test machine, at a 1.0 mm/min crosshead speed. The tests were performed first without cement to evaluate frictional resistance (Baseline), then with provisional cement (RelyX Temp NE without cement again (Baseline After RxT), and finally with resin cement (U200). The results were analyzed by ANOVA and Tukey test (p < 0.05). RESULTS Data evaluation as a function of cement type demonstrated the superiority of resin-based cements relative to provisional and baseline groups (p < 0.01). While Co-Cr crowns presented the highest pullout strength values, Pr showed the lowest values (data collapsed over cement) (p < 0.001). Retentiveness data as a function of both factors demonstrated similar pullout resistance between groups without cement (p < 0.001), except Zr baseline. Also, Co-Cr presented higher pullout strength compared to other materials. CONCLUSIONS Self-adhesive resin cement exhibited superior retention compared to temporary cement, regardless of crown material. Co-Cr and titanium presented higher levels of retention to Ti-base abutment after being cemented.

Background Acrylates and methacrylates are acrylic resin monomers that are known to induce skin sensitization as a result of their presence in different materials, such as nail cosmetics, dental materials, printing inks, and adhesives. Allergic contact dermatitis resulting from the use of modern wound dressings containing them has only rarely been reported. Objectives To describe 2 patients who developed allergic contact dermatitis caused by acrylic-based modern medical dressings and/or adhesives. Methods The medical charts of patients consulting since 1990 were retrospectively reviewed for (meth)acrylate allergy resulting from contact with such materials, and their demographic characteristics and patch test results were analysed. Results Two patients were observed in 2014 and 2016 who had presented with positive patch test reactions to several acrylic-based dressings and/or adhesive materials, and to several (meth)acrylates, that is, hydroxyethyl acrylate, hydroxyethyl methacrylate, ethyleneglycol dimethacrylate, bisphenol A-glycidyl methacrylate/epoxy-acrylate, urethane diacrylate, and/or penta-erythritol acrylate. Conclusions Allergic contact dermatitis needs to be considered in patients with eczematous reactions or delayed healing following the use of acrylic-based modern dressings or adhesives. However, identification of the culprit allergen is hampered by poor cooperation from the producers, so adequate labelling of medical devices is an urgent necessity.

Purpose Acrylic resin properties are susceptible to change over the duration of use, thereby decreasing prosthesis longevity. To make the material less susceptible to the action of external agents such as stain-causing liquids and cleaning solutions, polishing procedures are recommended. A specific mechanical polishing procedure performed regularly was evaluated regarding the biofilm adhesion, surface roughness (Ra), color stability (ΔE), and mass changes in acrylic resin artificial teeth. Materials and methods Sixty artificial teeth divided into two groups (n = 30) were immersed in distilled water (WT) and coffee (CF). These groups were then subdivided (n = 10) according to the type of polishing procedure administered: no polishing, biweekly polishing (once every 2 weeks) (pol 1), or monthly polishing (once a month) (pol 2), using aluminum oxide paste and a felt polishing wheel attached to an electric motor at a speed of 3000 rpm. Properties were evaluated at baseline and after 4, 8, 12, and 24 months of simulated immersion. At the end, the adhesion of Candida albicans and Streptococcus mutans multispecies biofilm in all groups was assessed. Results The CF group showed an increased Ra and weight, and a significantly greater ΔE compared to the WT group. The polishing procedure reduced Ra and minimized the stains caused by coffee, without losing mass, with the biweekly regime more effective than the monthly regime. Also, polishing reduced the adhesion of biofilm in the CF groups, again with the biweekly regime the most effective. Conclusions When performed regularly, the mechanical polishing procedure tested reduces the changes in artificial teeth subjected to immersion in coffee, with the biweekly frequency most effective regarding the properties evaluated.

PURPOSE To investigate the influence of food-simulating agents on the shear bond strength between direct hard liners and denture base acrylic resin. In addition, mode of failure was evaluated. MATERIALS AND METHODS One hundred fifty cylindrical columns of denture base resin were fabricated and bonded to three types of hard reline materials (Hard GC Reline, Tokuyama Rebase II Fast, TDV Cold Liner Rebase). Specimens of each reline material were divided into five groups (n = 10) to undergo 12-day immersion in distilled water, 0.02 N citric acid aqueous solution, heptane, and 40% ethanol/water solution at 37°C. The control group was not immersed in any solution. The shear bond strength test was performed, and the failure mode was determined. Statistics were analyzed with two-way ANOVA and chi-square test (α = 0.05). RESULTS Significant interaction was found between the hard liners and food simulating agents (p < 0.001). The shear bond strength of Tokuyama in 40% ethanol and TDV in heptane decreased significantly (p = 0.001, p < 0.001 respectively); however, none of the solutions could significantly affect the shear bond strength of Hard GC Reline (p = 0.208). The mixed failure mode occurred more frequently in Hard GC Reline compared with the other liners (p < 0.001) and was predominant in specimens with higher bond strength values (p = 0.012). CONCLUSIONS Food simulating agents did not adversely affect the shear bond strength of Hard GC Reline; however, ethanol and heptane decreased the bond strength of Tokuyama and TDV, respectively. These findings may provide support to dentists to recommend restricted consumption of some foods and beverages for patients who have to use dentures relined with certain hard liners.

Purpose To verify whether 0.1% and 0.2% sodium hypochlorite (NaOCl), and 8% Ricinus communis (RC) were able to remove denture biofilm without causing deleterious effects to acrylic resin. Background Previous data show that denture cleansers are effective in reducing biofilm; however, they can change acrylic resin properties. Methods In a crossover trial, 47 denture wearers brushed and soaked their dentures (20 min/14 d): control, 0.85% saline; SH1, 0.1% NaOCl; SH2, 0.2% NaOCl and RC. Denture biofilm on the intaglio surface was stained, photographed and quantified (Image Tool® ). Furthermore, 80 rectangular and 80 disc-shaped specimens (Lucitone 550) were assigned into tested solutions (n = 20), simulating 5 years of daily short immersions (20 minutes). A colorimeter and the National Bureau of Standards units (NBS) determined colour data (ΔE). Surface roughness and flexural strength were measured using rugosimeter and universal testing machine, respectively. Data were compared by the Friedman test (α = .05) followed by Wilcoxon, corrected by Bonferroni (α = .005) (clinical) and Kruskal-Wallis followed by the Dunn test (α = .05) (laboratorial). Results SH2 (MR=1.77) showed lower biofilm coverage; SH1 (MR = 2.37) and RC (MR = 2.74) presented intermediated values. RC (1.10 [0.96:1.75]) revealed higher colour alteration than SH1 (0.71 [0.62:0.80]) and SH2 (0.74 [0.58:0.85]); however, NBS classified all solutions as "trace" (0.0-0.5). There was no statistical significance for surface roughness (P = .760) and flexural strength (P = .547). Conclusions The 0.2% NaOCl showed the best clinical performance and did not cause adverse effects on acrylic resin on laboratory analyses.

PURPOSE The apical seal provided by a root canal filling may be breached via coronal leakage. This study aimed to compare the teeth restored with custom-made cast metal posts and cores cemented with different luting agents in terms of coronal microleakage after thermocycling. MATERIALS AND METHODS This in vitro study was conducted on 32 extracted single-canal teeth. Root canals were prepared by step-back technique and filled with gutta percha and sealer. The coronal 7 mm of gutta percha was removed, and post space was prepared using peeso reamers #2 and #3 consecutively. After fabricating the acrylic resin patterns of the posts and cores, they were cast using Ni-Cr metal alloy. The specimens were divided into 4 groups in which the castings were cemented using one of the following luting agents: zinc phosphate (ZP), glass ionomer (GI), Panavia F 2.0, and Speed CEM. After cementation, the teeth were immersed in distilled water and incubated for 7 days. Then, the teeth were subjected to thermocycling, immersed in silver nitrate for 6 hours, and finally sectioned. The degree of dye penetration into the coronal part of the specimens was measured using a stereomicroscope. Data were analyzed using Kruskal-Wallis and Mann-Whitey U tests with significance level of 0.05. RESULTS The median microleakage in ZP, Speed CEM, GI, and Panavia were 171.89, 114.76, 26.51, and 20.02 μm, respectively. Pairwise comparisons among GI and ZP, GI, and Speed CEM, ZP and Panavia, ZP and Speed CEM, and Panavia and Speed CEM groups yielded significant differences (p

PURPOSE To evaluate the accuracy of a digital implant impression technique using a TRIOS 3Shape intraoral scanner (IOS) compared to conventional implant impression techniques (pick-up and transfer) in clinical situations. MATERIALS AND METHODS Thirty-six patients who had two implants (Implantium, internal connection) ranging in diameter between 3.8 and 4.8 mm in posterior regions participated in this study after signing a consent form. Thirty-six reference models (RM) were fabricated by attaching two impression copings intraorally, splinted with autopolymerizing acrylic resin, verified by sectioning through the middle of the index, and rejoined again with freshly mixed autopolymerizing acrylic resin pattern (Pattern Resin) with the brush bead method. After that, the splinted assemblies were attached to implant analogs (DANSE) and impressed with type III dental stone (Gypsum Microstone) in standard plastic die lock trays. Thirty-six working casts were fabricated for each conventional impression technique (i.e., pick-up and transfer). Thirty-six digital impressions were made with a TRIOS 3Shape IOS. Eight of the digitally scanned files were damaged; 28 digital scan files were retrieved to STL format. A coordinate-measuring machine (CMM) was used to record linear displacement measurements (x, y, and z-coordinates), interimplant distances, and angular displacements for the RMs and conventionally fabricated working casts. CATIA 3D evaluation software was used to assess the digital STL files for the same variables as the CMM measurements. CMM measurements made on the RMs and conventionally fabricated working casts were compared with 3D software measurements made on the digitally scanned files. Data were statistically analyzed using the generalized estimating equation (GEE) with an exchangeable correlation matrix and linear method, followed by the Bonferroni method for pairwise comparisons (α = 0.05). RESULTS The results showed significant differences between the pick-up and digital groups in all of the measured variables (p < 0.001). Concerning the transfer and digital groups, the results were statistically significant in angular displacement (p < 0.001), distance measurements (p = 0.01), and linear displacement (p = 0.03); however, between the pick-up and transfer groups, there was no statistical significance in all of the measured variables (interimplant distance deviation, linear displacement, and angular displacement deviations). CONCLUSIONS According to the results of this study, the digital implant impression technique had the least accuracy. Based on the study outcomes, distance and angulation errors associated with the intraoral digital implant impressions were too large to fabricate well-fitting restorations for partially edentulous patients. The pick-up implant impression technique was the most accurate, and the transfer technique revealed comparable accuracy to it.

PURPOSE To evaluate the in vitro activity of 8% rosemary, 2% castor oils, and 12% propolis glycolic extract against Candida albicans, as well as the physical changes of properties in colorless and pink acrylic resins after immersion in these liquids. MATERIALS AND METHODS Colorimetric, roughness, and Knoop microhardness assays were evaluated in 25 specimens distributed into five groups (3 test groups and 2 control groups - distilled water and hypochlorite 1%), totaling five specimens per group for each acrylic resin (colorless and pink). The specimens were individually immersed for 30 minutes in 10 mL of these liquids, washed, and dried once a week. They were maintained in distilled water at 37°C between processes during all experiments. The analyses were performed before immersion and in the 4th and/or 12th month. In vitro, 18 acrylic resins were exposed to C. albicans and, after a process of 30 minutes in immersion in the five groups cited and oil vehicle control of vesicle (liquid Vaseline), the specimens were washed and incubated for 24 hours in 37°C. The growth was determined by colony counting. For comparisons between the groups in each trial and the disinfection test, paired Student's t-tests and ANOVA with post hoc Tukey were performed by the SPSS program, considering α = 0.05. RESULTS None of the liquids altered the microhardness, but all the natural compounds and 1% sodium hypochlorite (control) altered color and roughness after the 12th month of immersion in these agents. In the colorless specimens, 8% rosemary oil caused a color change similar to water, and less color and roughness alterations when compared to 2% castor oil and 1% sodium hypochlorite, respectively. There was no growth of yeast colonies after immersion in rosemary oil, propolis glycolic extract, and 1% sodium hypochlorite. CONCLUSION Eight percent rosemary oil has the potential to be used as an acrylic resin disinfectant.

A modified polyetheretherketone (PEEK) framework material in combination with heat-polymerized denture base acrylic resin was used for the fabrication of an overlay prosthesis for a patient sensitive to base metals. High noble metal was used for the fabrication of the post/coping/ball attachment assemblies to promote retention and stability. These protruding attachments into the acrylic resin could result in stress concentration; therefore, a framework is often used to strengthen the prosthesis. PEEK frameworks could be a treatment alternative to high noble or Ti frameworks since they combine good mechanical properties with biocompatibility, reduced cost, and common laboratory procedures.

OBJECTIVE To perform an in situ evaluation of surface roughness and micromorphology of two soft liner materials for dentures at different time intervals. BACKGROUND The surface roughness of materials may influence the adhesion of micro-organisms and inflammation of the mucosal tissues. The in situ evaluation of surface roughness and the micromorphology of soft liner materials over the course of time may present results different from those of in vitro studies, considering the constant presence of saliva and food, the changes in temperature and the pH level in the oral cavity. MATERIALS AND METHODS Forty-eight rectangular specimens of each of the two soft liner materials were fabricated: a silicone-based material (Mucopren Soft) and an acrylic resin-based material (Trusoft). The specimens were placed in the dentures of 12 participants (n = 12), and the materials were evaluated for surface roughness and micromorphology at different time intervals: 0, 7, 30 and 60 days. Roughness (Ra) was evaluated by means of a roughness tester. Surface micromorphology was evaluated by scanning electron microscopy. RESULTS Analysis of variance for randomised block design and Tukey's test showed that surface roughness values were lower in the groups using the silicone-based material at all the time intervals (P

Purpose To determine the shear bond strength (SBS) between zirconium framework and resin cements after different surface conditioner methods and after application of 10-methacryloyloxydecyl dihydrogen phosphate (MDP) based silane and a bonding agent mix. Materials and Methods 128 disc-shaped zirconium-oxide specimens were prepared. Specimens were placed in autopolymerizing acrylic resin. The bonding surface of specimens was smoothed consecutively with 600-, 800-, and 1200-grit silicon carbide papers under water cooling. Eight groups were prepared: CJ, Co-Jet; N, Nd-YAG laser; E, Er-YAG laser; NS, Nd-YAG laser + silane; ES, Er-YAG laser + silane; CJB, Co-Jet + bonding agent; NSB, Nd-YAG laser + silane + bonding agent; ESB, Er-YAG laser + silane + bonding agent. SEM analysis was performed under 2000× magnification. Dual- and self-cured resin cements were bonded to specimens, and shear force was applied. Data were analyzed with one-way ANOVA and Tukey's multiple comparison test (p < 0.05). Results The SBS values differed from each other among the groups. While the CJB group showed the highest values, the N group showed the lowest. The treatment with MDP-based silane and bonding agent mix increased SBS values of each cement belonging to each group. SB values of dual-cure resin cement were higher than those of self-cure resin cements. Conclusion Different surface conditioner methods exhibit an important effect on the SBS of resin cements to zirconium. The application of MDP-based silane and bonding agent mix enhanced SB values.

Objective Autopolymerized poly methyl methacrylate (PMMA) resin is commonly used for the construction of interim restorations; however, it has less than optimal mechanical properties. In this article, we evaluated the reinforcing effect of adding untreated zirconia nanoparticles on the flexural strength and surface hardness of this resin. Methods A total of 80 specimens were fabricated. Forty each were used for the flexural strength test and for the surface hardness test. The specimens were categorized into four groups of 10 specimens each as follows: pure PMMA, PMMA with 1%, PMMA with 2.5%, and PMMA with 5% weight of untreated zirconia nanofillers. The flexural strength of the specimens was evaluated by the three-point bending test, and the surface hardness was assessed by micro Vickers hardness test. The data obtained from these tests were statistically analyzed using one-way ANOVA and Tukey tests. In addition, the fracture surface characteristics were assessed using scanning electron microscopy. Results Flexural strength testing showed a significant increase in the group with 2.5% zirconia nanofillers, but not in the groups with 1% and 5% nanofillers. Surface hardness was also significantly increased in the groups with 2.5% and 5% nanofillers, but not in the 1% group. The SEM images showed a highly brittle fracture in the pure PMMA group and noticeably less brittle fracture in the group with PMMA with 2.5% weight of zirconia nanofillers. Several cracks and void were also observed in the group with 5% weight of nanofillers. Conclusion Reinforcement of the autopolymerized acrylic resin with 2.5% weight of untreated zirconia nanofillers significantly increased its flexural strength and surface hardness. Clinical significance The interim restorations play an important role in protection of hard and soft oral tissue and providing the critical function and esthetics before the final restoration replacing. Temporary restorations must have sufficient flexural strength to resist deformation during mastication force. Moreover, sufficient surface hardness is also necessary to resist abrasion. The color stability of materials is considered as an important clinical criterion, specifically in esthetics zone. Several materials have been applied to improve ‏the flexural strength and surface hardness for representing clinical success. Zirconia nanoparticles show desirable features, such as high hardness, biocompatibility, and favorable color because of its white color. ‏It seems that the addition of the nano zirconia to acrylic resins can be the appropriate method for improving interim restoration.

Acrylic coatings were modified by adding silica nanoparticles to obtain transparent, non-yellowing and chemically stable coatings, having also good corrosion resistance. Low carbon steel sheets were used as substrate. Pre-formed nano-silica particles, prepared by sol-gel chemistry from methyltriethoxysilane (MTES) and methacryloxypropyltrimethoxysilane (MPTMS) precursors, were dispersed into acrylic resin matrix. Unfilled coating was also produced for comparison. The uniformity of the coatings and the dispersion of nanoparticles in the polymeric matrix were investigated using transmission electron microscopy (TEM) and atomic force microscopy (AFM). The performance of the coatings was evaluated in terms of their UV resistance, optical properties, and corrosion resistance. The corrosion protection performance of the coatings was evaluated using potentiodynamic polarization technique and electrochemical impedance spectroscopy (EIS) in 3.5 wt% NaCl solution at room temperature. TEM studies indicate that silica nanoparticles were homogeneously dispersed through the polymer matrix. The polarization curves, corrosion resistance as measured by the Nyquist plots as well as salt spray tests suggest that the acrylic coating with homogeneously-dispersed nanoparticles offer the best protection against corrosion.

Purpose To evaluate in vitro the effect of the size of the unfilled space of the abutment screw access hole on the amount of extruded excess cement and the retention of zirconia copings. Materials and Methods Twelve dental implant replicas were attached to the corresponding abutments and embedded in acrylic resin blocks. A total of 36 CAD/CAM zirconia copings were fabricated by one technician using the standard technique. Abutments were divided into group I: the entire screw access channel was completely filled (nonspaced); group II: 1-mm-spaced; and group III: 2-mm-spaced. The copings were air-abraded and temporarily cemented under constant load of 60 N for 10 minutes. The excess cement was calculated as the difference between the post-cementation and post-excess-removal weights using a digital scale. Retention test was performed by a universal testing machine at a 0.5 mm/min crosshead speed. The ultimate force and tensile strength required for separation were recorded. One-way ANOVA and Tukey's test were used for statistical analysis at p ˂ 0.05. Results The average amount of extruded cement in groups 1, 2, and 3 was 33.48 ± 1.55, 23.05 ± 5.48, and 15.58 ± 5.98 mg, respectively. Multiple comparisons showed significant differences in the amount of extruded excess cement between the three groups (p ˂ 0.001). The maximum load at decementation in groups 1, 2, and 3 was 98.8, 87.5, and 88.6 N, respectively. Groups 1, 2, and 3 separated at 6.90 ± 1.2, 6.12 ± 0.7, and 6.21 ± 0.9 MPa, respectively, with no significant differences between them. Conclusions The amount of extruded excess cement was reduced by more than half when a 2-mm space of the screw access hole was left unfilled in comparison to the nonspaced counterpart. The retention of zirconia copings was not affected by the reported technique.

Summary In the formulation of acrylic coatings, monomer blends are required to cure in situ using a peroxide initiator. Curing accelerators (typically alkyl anilines) are added to the blend in order to initiate the curing process at room temperature. This was proved to cause a process safety issue related to the presence of accelerators that increase the possibility of runaway reactions especially at industrial scale. In this paper, the polymerization of methyl methacrylate containing different curing accelerators has been studied. Based on Differential Scanning Calorimetry tests, a simplified kinetic model for the polymerization process has been developed, describing the induction time due to the presence of stabilizers, the global kinetic rate, and the influence of diffusion phenomena, based on a free volume theory approach specifically modified for the free radical polymerization of methyl methacrylate added with different types of accelerators.

Acrylic resins for automotive coatings are produced in nonaqueous dispersions (NAD) of nanometer size. These must be sterically stabilized by oligomeric dispersants, which are complex reactive oligomers possessing vinyl and hydroxyl functionalities, controlling the size of the nanocolloid. Hence, we have developed a kinetic Monte Carlo (kMC) model to improve the molecular structure of 2-hydroxyethyl methacrylate-functionalized poly (butyl methacrylate) (pBMA) dispersants of ca. 6,000 g/mol produced via semi-batch cobalt chain transfer polymerization (CCTP). The kMC-predicted degree of functionalization is benchmarked against a novel analytic expression suitable for oligomers. Stepwise adjustment of the semi-batch feed program illustrates the successive improvement in molecular structure of the dispersant product, finally arriving at a functionalization degree close to the theoretical maximum for CCTP.

WOS: 000471710100014, PubMed: 30298558, Purpose To evaluate the effect of adding Al2O3, SiO2, and TiO2 nanoparticles in ratios of 1, 3, and 5 wt% to different acrylic resins on flexural strength. Materials and Methods A total of 210 specimens were prepared in 30 groups (n = 7/group) (Control, 1% Al2O3, 3% Al2O3, 5% Al2O3, 1% SiO2, 3% SiO2, 5% SiO2, 1% TiO2, 3% TiO2, 5% TiO2). The specimens were polished with 200-, 400-, and 600-grit abrasive paper to provide a standard surface before testing and then suspended in distilled water for 30 days. Flexural strength was measured via three-point bending tests. Subsequently, SEM analysis was performed for one specimen from each group. Homogeneity of data was assessed by Kolmogov-Smirnov test followed by two-way ANOVA and Tukey HSD tests (alpha = 0.05). Results There was a significant increase in the flexural strength of polymethylmethacrylate (PMMA) after addition of 1% nanoparticles in both heat-polymerized and autopolymerized acrylic resins (p < 0.05). The flexural strength values of the groups to which Al2O3 and TiO2 nanoparticles were added exceeded those of the group with SiO2 addition (p < 0.05). The electron microscopy images revealed that the nanoparticles were more homogeneously dispersed in PMMA with higher flexural strength. Conclusions The mechanical properties of PMMA can be improved by the addition of nanoparticles to PMMA; however, the flexural strength values of PMMA decrease with the addition of nanoparticles at higher percentages (3-5%). Hence, the ideal filler ratio corresponds to 1%., Selcuk University Scientific Research ProjectsSelcuk University [16102013], This study was supported by Selcuk University Scientific Research Projects (project number 16102013).

Purpose To evaluate how hydrophobic nanoparticle silica and prepolymer affect the flexural strength, surface hardness, surface roughness, and resilience of a denture base acrylic resin. Materials and Methods A total of 40 denture base acrylic resin specimens with dimensions 65 × 10 × 3 mm3 were fabricated in this study. Specimens were divided into five experimental groups (n = 8) according to surface-treated silica and prepolymer concentration incorporated into the acrylic resin (weight %) prior to polymerization: G1 acted as control, no fillers were used in this group. G2: 1 wt% 12 nm silica nanoparticles; G3: 5 wt% 12 nm silica nanoparticles; G4: 1 wt% 12 nm prepolymer nanoparticles; G5: 5 wt% 12 nm prepolymer nanoparticles were added into the acrylic mixture. Acrylic specimens were polymerized according to the manufacturer's instructions. Three-point bending test was performed to evaluate the flexural strength and the resilience of the specimens. Then, a digital profilometer was used to determine the surface roughness of the specimens. Surface hardness was conducted by a digital Shore D hardness testing machine. Surface analysis of one specimen in each group was performed with a scanning electron microscopy (SEM) to observe the fracture surfaces of specimens. ANOVA and Tukey tests were used for the statistical analysis (p

A parametric study was carried out to investigate the effects of process parameters on the properties of opaque and/or colored polymer pigment. The core was synthesized using methyl methacrylate (MMA), methacrylic acid (MAA), and ethylene glycol dimethacrylate, and the shell from styrene. The surfactant/water (S/W) ratio was changed between 0.56 and 1.46, and the best ratio was determined to be 0.97. The increase in the amount of MAA and the pH of the medium increases the diameter of the swollen particles. The hollows could form only when the fraction of MAA in the monomer mixture was above 10%, and pH ≥ 10. The opaque pigment with the largest diameter could be obtained at the S/W ratio of 0.97 and the MAA content of 20%, as 350 nm. It gave an opacity value of 93.8% when mixed with an acrylic resin at 50% by volume. The colored opaque polymer pigments were synthesized by adding copper phthalocyanine into the monomer mixture. The addition of 2% copper phthalocyanine yielded a green-blue color but 3% yielded blue color. The latter yielded a change in the lightness (ΔL*) by a value of −31.49, and a total color difference (ΔE*) of 30.05 compared with that of white opaque polymer pigment. POLYM. ENG. SCI., 57:913–920, 2017. © 2016 Society of Plastics Engineers

Fiber-reinforced thermoplastic composite materials can find numerous applications in the transportation sector and replace thermoset composites. However, they have to comply with strict standards, particularly with those concerning their fire behavior. In this frame, composites based on an acrylic resin Elium ® (Arkema), a woven fiberglass, (taffetas tissue Chomarat G-Weave 600 P/A) and Exolit OP930 (Clariant) as fire retardant were prepared using three processes. The thermal stability and fire behavior was studied by means of thermogravimetric analysis and cone calorimetry. The obtained results allowed to highlight the drawbacks of each processing method and to select the most appropriate. The improvement of the fire behavior by combining post-curing of the composites, addition of a cross-linking agent and addition of aluminum trihydroxide (ATH) was also investigated.

A systematic investigation of the effect of the presence of acrylate resin on polysulfone-based membranes was performed with the aim of obtaining chemically stable crosslinked membranes without affecting their flux performances. The membranes were prepared via UV curing of the polymer dope followed by a non-solvent-induced phase separation process. Two different acrylic monomers were investigated and their amount was varied in the polymer dope, to study the influence of concentration on final results. High crosslinking degrees were achieved by irradiating the solution for one minute. Morphological investigations of the active surface and of the cross-sections of the fabricated membranes showed that the typical porosity of ultrafiltration membranes was obtained starting from solutions containing a low amount of crosslinker (10 wt%), which is consistent with the water flux values which were comparable to that of the pristine polysulfone membrane. High concentrations of crosslinker resin in the initial polymer dope produced denser membranes with lower permeability. High rejection of 27 nm particles (>90%) was measured for all samples having measurable flux. The addition of the crosslinker allowed one to obtain stability in various solvents without affecting the flux and rejection performance of the porous membranes. © 2016 Society of Chemical Industry

To evaluate the effect of chlorhexidine (CHX) on fracture resistance of roots treated with different concentrations of ethylenediaminetetraacetic acid (EDTA).One hundred and twenty intact single-rooted premolar teeth were sectioned below the cementum-enamel junction to standardize the length of the teeth to 12 mm. The canals of one hundred specimens were instrumented with ProTaper Universal rotary instruments up to size F4 and were randomly divided into five groups (n = 20) according to the final irrigating solutions: Group 1: distilled water (DW); Group 2: 5% EDTA and 2.5% NaOCl; Group 3: 17% EDTA and 2.5% NaOCl; Group 4: 5% EDTA, 2.5% NaOCl, DW and 2% CHX; Group 5: 17% EDTA and 2.5% NaOCl, DW and 2% CHX. Root canals were filled with gutta-percha and epoxy resin-based root canal sealer using a single-cone technique. Twenty teeth served as negative controls and were not instrumented nor root filled (Group 6). All specimens were embedded in self-curing acrylic resin and loaded vertically at 0.5 mm minGroup 1 (only DW) had the lowest vertical fracture strength, followed by Group 3 (17% EDTA and 2.5% NaOCl; P 0.05). Group 6 (negative control group) had the highest fracture resistance. Final irrigation with CHX following irrigation with 17% EDTA or 5% EDTA and 2.5% NaOCl (groups 4 and 5) significantly increased the fracture resistance of roots (P 0.05). However, the difference between Group 4 and Group 5 was not significant (P 0.05).Intracanal CHX rinse of EDTA/NaOCl-treated root dentine enhanced the fracture resistance of roots filled with AH Plus.

Purpose To assess the effects of terpenic denture cleanser on denture biofilm removal using scanning electron microscopy (SEM). Materials and Methods The internal surface biofilm of four maxillary dentures was elucidated with Caristop-revelador Dual Tone, and 40 blue-stained specimens (0.6 cm × 0.4 cm × 2 mm) were obtained. These specimens were randomly assigned to one of the following four groups of 10 specimens each: control, Eci Clean, Fitty Dent, and terpenic denture cleanser. The period of immersion in each solution was 12 hours. Biofilm removal was evaluated using SEM, and morphologically varying areas of the SEM images were quantified with Imaris software. The data were analyzed using Kolmogorov-Smirnov, t-tests, ANOVA, and Tamhane's tests (p = 0.05). Results Data revealed that terpenic denture cleanser removed significantly more biofilm than any other treatment examined in this study. The t-tests revealed significant differences in the clean area that resulted from the use of the terpenic cleanser compared with the clean area that resulted from the use of Eci Clean (p = 0.013). Fitty Dent was the least effective and left dirty acrylic resin. The average areas with few removed layers were 59.3%, 43.3%, and 9.5% in Fitty Dent, Eci Clean, and terpenic cleanser groups, respectively. Tamhane's tests indicated that the Eci Clean and Fitty Dent groups were significantly different from the 0.5% terpenic cleanser group (p = 0.008). Conclusion The terpenic denture cleanser was effective in removing denture biofilm.

Purpose Dental prosthetic and orthodontic appliances are transported from the clinic to the laboratory for additions and repairs. These appliances, containing microbes from the oral flora, are a high risk for cross-contamination. The aim of this study was to evaluate the effect of chemical and ultrasound disinfection against two in vitro biofilms and an in vivo formed biofilm grown on unprepared and polished polymethyl methacrylate (PMMA) surfaces. Materials and Methods Rough and polished self-curing PMMA surfaces were infected with strains of both Candida albicans and Streptococcus oralis. After incubation, the samples were treated with different disinfection methods, including ultrasound treatment for both 15 and 30 seconds, and immersion in glutaraldehyde and alcohol-based chemical disinfectants (MD520 and Minuten, respectively). The disinfecting efficacy was assessed by colony forming units (CFU) analysis and by scanning electron microscopy (SEM). Furthermore the adequacy of bacterial elimination of application of 30-second ultrasound and MD520 was assessed on PMMA retrieved from ten volunteers by CFU analyses. ANOVA with p = 0.05 followed by the Tukey post hoc test and the Student t-test was used to analyze the data. Results The ultrasound treatment for 30 seconds, MD520, and Minuten were the most effective disinfectant methods as they reduced the microbial counts compared to the control (p < 0.05) as shown in the in vitro analyses. S. oralis adhered more to rough acrylic resin surfaces (p < 0.05). Ultrasound treatment was the most effective way to reduce microbial counts on PMMA exposed to oral flora (p = 0.043). Conclusion Ultrasound treatment for 30 seconds was effective against C. albicans, S. oralis, and the oral flora as shown by testing microbial growth on agar plates and SEM.

In this study, the efficacy of creating cellular hydrogel coatings on warm tissue surfaces through the minimally invasive, sprayable delivery of thermoresponsive liquid solutions was investigated. Poly(N-isopropylacrylamide)-based (pNiPAAm) thermogelling macromers with or without addition of crosslinking polyamidoamine (PAMAM) macromers were synthesized and used to produce in situ forming thermally and chemically gelling hydrogel systems. The effect of solution and process parameters on hydrogel physical properties and morphology was evaluated and compared to poly(ethylene glycol) and injection controls. Smooth, fast, and conformal hydrogel coatings were obtained when pNiPAAm thermogelling macromers were sprayed with high PAMAM concentration at low pressure. Cellular hydrogel coatings were further fabricated by different spraying techniques: single-stream, layer-by-layer, and dual stream methods. The impact of spray technique, solution formulation, pressure, and spray solution viscosity on the viability of fibroblast and osteoblast cells encapsulated in hydrogels was elucidated. In particular, the early formation of chemically crosslinked micronetworks during bulk liquid flow was shown to significantly affect cell viability under turbulent conditions compared to injectable controls. The results demonstrated that sprayable, in situ forming hydrogels capable of delivering cell populations in a homogeneous therapeutic coating on diseased tissue surfaces offer promise as novel therapies for applications in regenerative medicine. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 2383-2393, 2016.

Objective The purpose of this study was to evaluate the marginal fit of different zirconia and metal frameworks and compare them with each other on different finish line configurations. Materials and methods 20 stainless steel dies 10 with shoulder and 10 with chamfer finish line including 6 mm preparation height and 3 degree axial angle simulating a 6 degree total occlusal covergence of the prepared tooth were produced. After embedding the each group of die into the arch-shaped acrylic resin blocks, impressions were made using silicone based impression material and 120 casts were prepared subsequently. The dies were divided into six groups each having 20 specimens (10 with shoulder, 10 with chamfer finish line). Group CM consisted of Co-Cr produced by conventional casting procedure, group MM of Co-Cr prepared by metal milling, group LM of Co-Cr prepared by direct laser metal sinterization (DLMS), group ZZ of Zirkonzahn (Zirkonzahn GmbH, Gais, Italy), group LZ of Lava Zirconia (3 M ESPE Dental AG, Seefeld, Germany) and group DZ of DC-Zirkon (DCS Dental AG, Allschwil, Switzerland). Stereomicroscope were used to evaluate the marginal fit of frameworks and marginal gap values obtained from the images were analyzed using Mann-Whitney U Test and Kruskal-Wallis H Test with Bonferroni correction. Results The lowest value of marginal gap was identified in the samples from the LZ group and the highest value was identified in those from ZZ in both finish lines. The effect of finish lines was not significant for most groups but CM frameworks with chamfer finish lines and the DZ frameworks with shoulder finish lines showed significantly lower marginal gap values. Conclusion The marginal gaps of the various tested zirconia and metal framework were within the range of clinical acceptability (120 µm). Clinical significance The results of this in vitro study suggest that margin preparation design and type of zirconia and metal framework materials for various CAD-CAM systems have a significant effect on marginal fit of the resulting restorations. (J Esthet Restor Dent 28:238-246, 2016).

PURPOSE Denture tooth debonding is a common complication for denture wearers; however, the effect of complete denture disinfection on bonding between denture teeth and acrylic resin remains unclear. The aim of this study was to evaluate the effect of disinfection methods on the bond strength between denture teeth and microwave-cured acrylic resin denture base. MATERIALS AND METHODS Three commercial brands of denture teeth (Trilux, Biolux, Vipi Dent Plus) and one microwave-cured acrylic resin denture base were tested. Each brand of denture teeth was divided into seven groups (n = 6; estimated by partial Eta squared). The specimenss of groups H and Cl were immersed in 1% sodium hypochlorite and 4% chlorhexidine digluconate for 7 days, respectively. In group Br, the specimens were subjected to toothbrush simulation under 200 g of force for 20,000 cycles. In groups Br-H and Br-Cl, the specimens were brushed and further disinfected with 1% sodium hypochlorite and 4% chlorhexidine digluconate, respectively. In control groups 1 (Co1) and 2 (Co2), the specimens were stored in distilled water for 50 ± 2 hours and 7 days, respectively. Shear bond strength testing was performed at the resin/tooth interface in a universal testing machine at a 1 mm/min crosshead speed. The failure pattern was quantified and classified into adhesive, cohesive, or mixed. Data were analyzed using two-way ANOVA and Tukey HSD test (α = 0.05). RESULTS Disinfection with 1% sodium hypochlorite (p = 0.031), brushing (p 0.05). The failure pattern was predominantly adhesive independent of the disinfection method and denture tooth brand. CONCLUSIONS Disinfection with sodium hypochlorite, brushing, and the association of mechanical and chemical methods reduced the bond strength between denture tooth and microwave-cured acrylic resin denture base.

Purpose To assess the effect of brushing with different solutions on the abrasion resistance of two types of acrylic resin teeth. Materials and Methods Maxillary premolars from two types of acrylic teeth (Biotone and Biotone IPN) were divided into six groups (n = 12), according to the solution used during brushing: distilled water (control), coconut soap, or dentifrice. A mechanical brushing machine was used to simulate approximately 1 year of brushing (11,000 strokes). The weight loss (WL) of teeth was obtained from the difference between the initial (IW) and final weight (FW) of each specimen, and the mean of percentage of weight loss (PWL) was calculated for each group. Data were analyzed using the Kruskal-Wallis test, followed by Bonferroni's post-test comparison (α = 0.05). Results A statistically significant difference was found for the factor solution (p < 0.001). Brushing using dentifrice caused the highest values of weight loss (–0.50%), in comparison with the groups brushed with coconut soap (0.00%) or distilled water (0.00%). Conclusions For both types of artificial teeth, brushing with dentifrice produced higher abrasion than brushing with coconut soap or water.

Purpose To evaluate a solution based on Ricinus communis (Castor oil) for denture cleansing, comparing it to sodium hypochlorite (NaOCl) for the surface roughness of heat-polymerized acrylic resin. Materials and Methods Forty polished and unpolished resin specimens (90 × 30 × 4 mm) were evaluated before and after their exposure to protocol hygiene: brushing the specimens with a specific denture brush and mild soap for 3 minutes, three times a day, and immersing them in hygiene solutions (0.25% NaOCl—S1 and 0.5% NaOCl—S2; 10% R. communis—S3; saline—S4: control) for 20 minutes. Surface roughness was evaluated by rugosimeter and scanning electron microscopy (SEM) before and after the protocol. For evaluation of surface roughness, polished and unpolished surfaces were used. Results The roughness of the polished surface was not affected by time (p = 0.062), but was affected by solutions (p < 0.0001) and the interaction between factors (p = 0.005). For S1 and S4, the period did not influence the roughness. For S2, there was a change after 7 days, remaining stable after 14 days. For S3, there were changes, and stabilization occurred after 14 days. After 7 and 14 days, S2 and S3 promoted major changes, but after 21 days, there were no differences among solutions, except saline. The unpolished surface was not influenced by factors: period (p = 0.115), solution (p = 0.120), and their interaction (p = 0.382). SEM analysis showed similar results on the evaluation of surface roughness. Conclusions The polished surface of the prosthesis was more susceptible to changes when exposed to hygiene solutions, and although the 0.5% NaOCl solution promoted an increase in the surface roughness compared with the same solution at 0.25% and R. communis at 10%, the values are clinically acceptable.