Search

In order to fully reveal information about landslide displacement, it was necessary to extend a time series to a higher-dimensional state space for the characteristic of univariate time series. However, in order to control the expansion of noise, an appropriate embedded dimension of phase space reconstruction was not the bigger the better. In this paper, based on the displacement time series of landslide, the phase space theory was used to build displacement time series matrix and the entropy theory was used to get the entropy. The embedded dimension of phase space reconstruction could be adjusted according to the change of entropy and feedback of displacement prediction error and a support vector regression model was created via the support vector machine’s learning. The application on Baijiabao landslide indicates that the proposed method achieves a high accuracy and stability of prediction.

The components of a fermentation medium were optimized to produce cellulose from HDZK-BYTF620 (Aureobasidium pullulans) which is from the gut of termites and can produce cellulose under liquid state fermentation conditions by response surface methodology. By Plackett-Burman design screened out three major factors of strains HDZK-BYTF620 which affected production of the activity cellulose, immediately, CaCl2, MgSO4and CMC-Na. The fermentation conditions were optimized with Box-Behnken experiment and the largest regional of the activity of cellulase was approach with the steepest ascent experiment. The optimum composition of medium addition of CaCl2, MgSO4and CMC-Na was 0.77 g/L, 0.41 g/L and 21.88 g/L, respectively. Under the optimum fermentation medium conditions, the activity of cellulase was (598.00±2.56)×10-3IU/mL, increased 5.0 % to that of using initial medium.

Nonlinear equivalent spring resistance model and Coulomb friction model is used to construct a dynamic mathematical model for a multi-body system, which contains clearance. In the paper an internal combustion engine dynamic model has created for simulated analysis. It shows that joints accuracy and driver speed have obvious effects on crank slider dynamic disturbance. Also joints clearance and the increase of driver speed lead to lower positional accuracy, worse stability and reliability, which has very important theoretical significance and practical value on the analysis of the performance of internal combustion engine.

Sinusoidal signal generator is common electronic equipment. In this paper, the writer designed a kind of integrated CMOS sine signal generator, which generator uses wien bridge oscillation circuit.This generator circuit mainly constitutes by amplifier, leveled and low-pass filter circuit, which uses Cadence software to simulate and analysis its amplification circuit, in order to get a sine wave which has high performance accuracy and stability. Through simulating this generator, we can get a kind of sine wave which includes the frequency as the 1.109 kHz, the center potential as 2.5V, the amplitude as 2.58V, distortion is less than 2%, and this sine wave is more practical for the lower voltage supply system.

A design project of voltage controlled oscillator which is the central component of the low voltage phase locked loop (PLL) is proposed in this paper. The VCO adopted the folding differential voltage controlled oscillator.Simulation results in Cadence Hspice indicate that the VCO proposed behaves in good linearity, simple structure, small phase noise.The frequency range from 125 to 787 MHz, the power consumption of this oscillator is only 6mW at central frequency is 480MHz with 3V power supply.

In this paper, the author designed the model of instruction expert system based on improved genetic algorithm and described the realization of improving exercises in detail. In this system, the students can online learn through different modes and receive the guidance from the teacher, meanwhile the analysis to effect the parameter of intelligent tests generating will be produced. So the following exercises focus on the student’s weakness, this is useful to enhance the students’ the knowledge level and operation ability.

In this paper, the mechanical properties and permeability of the concrete with steel slag coarse aggregates were investigated by comparing with the concrete with crushed limestone coarse aggregates. Results show that the concrete with steel slag aggregates shows similar strength with the concrete with crushed limestone aggregates at the age of 28 days, but it shows a little higher strength especially splitting tensile strength at the age of 90 days. Steel slag coarse aggregates tend to have limited influence on the elastic modulus and permeability of concrete. The results at different water to cement ratios are similar.

The properties of the concrete with super-fine steel slag were compared with those of the pure cement concrete. Results show that the concrete with 20% super-fine steel slag has similar compressive strength, elastic modulus, and permeability with the pure cement concrete at the age of 28 and 90 days. The addition of super-fine steel slag tends to decrease the initial slump of concrete, but it has a good ability of prevention of slump loss. The concrete with super-fine steel slag has similar anti-carbonation capacity with the pure cement concrete. The concrete with 30% super-fine steel slag has lower compressive strength, lower elastic modulus, and higher permeability than the pure cement concrete.

Product design is successful or not, not only from the aspects of design concepts, ideas, manufacturability, cost and benefit considerations, the most important depends on the customer satisfaction after products is throw on the market. Many products only from the point of view of design are impeccable, but the user feedback is not good, in order to meet the demands of the market need, you need to constantly improve and innovate. For a certain brand rearview mirror product user feedback, the design of crank connecting part curvature has been modified using reverse technology.

Steel truss bridge is an important part of transportation hub and lifeline engineering, it recently has attracted more attention on dynamic performance of steel truss bridge. In this paper, the ANSYS software is used to perform the modal analysis of steel truss bridge, and we find that the main bridge are more sensitive to the vertical earthquake (i.e., Y direction). In the earthquake response spectrum analysis on Y direction, we find that the maximum deformation is at mid-span of steel truss bridge. In the transient analysis of seismic waves, under the action of horizontal and vertical earthquake accelerations, the structure displacement dynamic diagram and time-history displacement curve are obtained and some conclusions are drawn.

N, Fe co-doped TiO2 photocatalyst was synthesized by sol-gel method. The catalyst prepared was characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Ultraviolet and visible spectroscopy (UV-vis). The results showed that the N, Fe co-doped TiO2 prepared had the anatase structure. The absorption edge of the photocatalyst shifted to longer wavelength and photocatalytic activity for degradation of Methylene blue (MB) under Xe-lamp (350 W) was much more active than un-doped TiO2, N-TiO2 Fe-TiO2 and P-25.

The paper presents a simulation platform for the development of vehicle adaptive cruise control (ACC) systems. The simulation platform has the ability to simulate traffic driving conditions and critical driving conditions and covers software-in-the loop and hardware-in-the-loop test capabilities. First, the system architecture of the simulation platform is introduced. All components of the platform are defined. Those components build the basis for the entire simulation. Special emphasis is given to the interaction between the simulated vehicle and its traffic environment. Second, this paper provides a radar sensor model framework and a vision sensor model framework to establish virtual sensor models to enable high-fidelity simulation on environmental sensing and perception for virtual development, testing and validation of ACC system. Finally, this paper gives an example of ACC under traffic conditions to verify the simulation platform.

Ceramic materials has approximate color and translucency with natural tooth, which is unmatched by other restorative materials. Because of its beautiful appearance, good physical and chemical properties, all-ceramic crown restorations are more widely used. However, due to the brittleness of ceramics and the stress mismatch between different materials, failure phenomenon is often observed during the service period of all-ceramic crowns. The failure process and mechanism are not clear, in this paper, the force performance of all-ceramic crowns is analyzed using the RFPA (realistic failure process analysis) system. The crack initiation, propagation and failure process of all-ceramic crown can be clearly observed and the research results provide guidance for clinical application.

Cognitive Radio Networks is an effective technology and a hot research direction which can solve the problem of deficient resource and revolutionize utilization. In order to enhance the communication efficiency, secondary users are classified by some strategy. We exploit the queuing theory model to research on the communication performance of secondary users, considering primary user as the first grade user and secondary users as other grades users. The research results indicate that the users which have lower priority level are more sensitive than those have higher priority level when primary user appears. Under Primary User Emulation Attack (PUEA), if the number of secondary users reaches 300, the waiting time would larger than 15 minutes. And if the appearance rate of PUEA reaches 4, the break-out rate would be 80%, which is much harmful for CRN.

Many fundamental ecosystem properties and dynamics are monitored by plant water status, particularly in arid ecosystem where water is usually limiting. Although plant water status have been widely assessed using field measurements by ecological methods, approaches for remotely sensing plant water status are largely lacking, particularly diurnal water status. In arid ecosystem, WUE is a dynamic indicator for detecting water status, but also an integrated index for correlating to the plant photosynthesis. In our study, the experiments were conducted on native dominant desert shrub, Tamarix ramosissima, in their original habitats on the southern periphery of Gurbantonggut desert, China. We explored sensitive and useful hyperspectral indices for estimating diurnal WUE at a leaf scale based on diurnal measurements of hyperspectral reflectance, photosynthesis and micrometeorological variables. According to the statistical analysis of relationships between spectral indices and WUE estimation, SR type hyperspectral index is the sensitivity index for WUE estimation. Our results provide useful insights for monitoring desert shrubs diurnal and dynamic water status, using a wide range of available hyperspectral data.

T-shirt attracts a crowd of various consumers and endures worldwide popularity for both ever-changing style and colour-rich. In this article, it takes 42 men’s T-shirts as the objects, “fashionable” and “preferable” as emotional stimuli words were used from the point of view visual cognition. The aim of this paper is to provide concrete basis for the design of more fashionable and preferable emotion of men’s T-shirts to meet the needs of young consumers.

Electroplating was employed to prepare Cu films and Ni films on Ag substrates. The average internal stresses in Cu film and Ni film were measured in situ by cantilever beam test. The values of experimental internal stresses were compared with theoretical internal stresses. The results showed that the internal stresses of Cu film and Ni film decreased with the increase of the film thickness. The reduced gradient was faster. The values of experimental and theoretical internal stresses had the same variation trend with film thickness and the same characteristics (tensile stress). Theoretical calculation model of internal stress was of accuracy. The internal stress for the same substrate was in relation to the film material.

A bolometer with stress equilibrium based on α-Si and metal films is proposed in this paper. The sensitive and support material α-Si films are prepared by plasma enhanced chemical vapor deposition（PECVD）, their stress and deposition rate are studied, and the technological parameter of the low stress and higher temperature coefficient of resistance (TCR) α-Si film are obtained. The result shows that the stress of the α-Si films can be adjusted between positive and negative. Pt films are deposited by electron-beam evaporating equipment. Their square resistance, TCR and stress are tested by four point resistivity test system and film-stress interferometer. The result shows this material is a good heat-sensitive material, and at the same time it can balance the stress of α-Si film. Finally it is found that Pt film is in compressive stress state in the selected technological parameters, and α-Si thin film is in tensile stress state, so the stress of micro-bridge structure can be balanced by this method. In the final, 160×120 infrared micro-bridge array on the wafer and read out integrated circuit (ROIC) chip are successfully fabricated.