Search

In this paper, a 12-bit high resolution, power and area efficiency hybrid digital pulse width modulator (DPWM) with process and temperature (PT) calibration has been proposed for digital controlled DC-DC converters. The hybrid structure of DPWM combines a 6-bit differential tapped delay line ring-mux digital-to-time converter (DTC) schema and a 6-bit counter-comparator DTC schema, resulting in a power and area saving solution. Furthermore, since the 6-bit differential delay line ring oscillator serves as the clock to the high 6-bit counter-comparator DTC, a high frequency clock is eliminated, and the power is significantly saved. In order to have a simple delay cell and flexible delay time controllability, a voltage controlled inverter is adopted to build the deferential delay cell, which allows fine-tuning of the delay time. The PT calibration circuit is composed of process and temperature monitors, two 2-bit flash ADCs and a lookup table. The monitor circuits sense the PT (Process and Temperature) variations, and the flash ADC converts the data into a digital code. The complete circuits design has been verified under different corners of CMOS 0.18um process technology node.

Conventional synchronous design circuits cannot only satisfy the timing requirement of the low voltage digital systems, but also they may generate wrong outputs under the influence of PVT variations and aging effects. Therefore, in this paper, a NCL (Null Convention Logic) design as an asynchronous design method has been proposed, where the NCL method doesn`t require any timing analysis, and it has a very simple design methodology. Base on the NCL method, a new low power reliable ALU has been designed and implemented using MagnaChip-SKhynix 0.18um CMOS technology. The experimental results of the proposed NCL ALU have been compared to those of a conventional pipelined ALU in terms of power consumption and speed.

As CMOS technology is scaled down more aggressively, the reliability mechanism (or aging effect) caused by the diffusion of metal atoms along the conductor in the direction of the electron flow, also called electromigration (EM), has become a major reliability concern. With the present of EM, it is difficult to control the current flows of the MOSFET device and interconnect. In addition, nanoscale CMOS circuits suffer from increased gate leakage current and power consumption. In this paper, the EM effects on current of the nanoscale CMOS circuits are analyzed. Finally, this paper introduces an on-chip current measurement method providing lifetime electromigration management which are designed using 45-nm CMOS predictive technology model.

Ultra low-power design and energy harvesting applications require digital systems to operate under extremely low voltages approaching the point of balance between dynamic and static power consumption which is attained in the sub-threshold operation mode. Delay variations are extremely large in this mode. Therefore, in this paper, a new low-power logic design methodology using asynchronous NCL circuits is proposed to reduce power consumption and not to be affected by various technology variations in nanoscale MOSFET technology. The proposed NCL is evaluated using various benchmark circuits at 0.4V supply voltage, which are designed using 45nm MOSFET predictive technology model. The simulation results are compared to those of conventional synchrouns logic circuits in terms of power consumption and speed.

This paper presents the impact of time dependent dielectric breakdown (TDDB, also called as gate oxide breakdown) failure on nanoscale digital CMOS Circuits. Recently, TDDB for ultra-thin gate oxides has been considered as one of the critical reliability issues which can lead to performance degradation or logic failures in nanoscale CMOS devices. Also, leakage power in the standby mode can be increased significantly. In this paper, TDDB aging effects on large CMOS digital circuits in the 45nm technology are analyzed. Simulation results show that TDDB effect on MOSFET circuits can result in more significant increase of power consumption compared to delay increase.

This paper proposes a new input pattern generator for minimal leakage power in the nanometer CMOS technology considering all the leakage current components (sub-threshold leakage, gate tunneling leakage, band-to-band tunneling leakage). Using the accurate macro-model, a heuristic algorithm is developed to generate a input pattern for the minimum leakage. The algorithm applies to ISCAS85 benchmark circuits, and the results are compared with the results of Hspice. The simulation result shows that our method"s accuracy is within a 5% difference of the Hspice simulation results. In addition, the simulation time of our method is far faster than that of the Hspice simulation.

Ubiquitous network and wireless sensor networks is being applied in various fields. Located at target areas, node of wireless sensor network uses batteries as a power source. Batteries have a limited energy in sensor network applications. Also, before use, the battery must be charged and It is difficult to replace the battery. Therefore, energy harvesting technology is being researched and being developed for long life of sensor node. Especially, sola energy is being extensively researched. because that can have great amounts of energy than other environmental energy in a short time. In this study, we tested battery charging and recharging, operation of sensor node using Solar Cell. Also, monitoring data gathering and voltage Analysis showed energy harvesting time of Sola Cell battery for sensor node and operation of sensor node.