Search

In this article, we give out the formulations of the fields in a three-layer fiber. For a typical step-index single-mode fiber, we calculate propagation constants and mode field profiles of the cladding modes in it. Results show that the hybrid cladding modes, whose azimuthal quantum number is not zero, can also be rigorously divided into HE and EH modes. Comparison with the results of the two-layer geometry approximation indicates that when solving the cladding modes in a fiber the simplified model is unsuitable. [ABSTRACT FROM AUTHOR]

We successfully simulated the 10 × 40 Gbit/s soliton RZ-DPSK WDM signals over 1050 km with spectral efficiency approaching 0.4 bit/s/Hz using semiconductor optical amplifiers (SOAs) as in-line amplifier. The cross-gain saturation of SOA can be minimized by settling crosstalk at a lower level by decreasing the differential gain. This decrease in differential gain is in such a way that we get nil power penalty. The maximum transmission distance of 1050 km is possible with differential gain 210 atto cm 2 of SOA. The impact of amplification factor, ASE noise power, crosstalk, quality factor and bit error rate for different differential gain has been investigated. It has been shown that with the increase in differential gain of SOA, the transmission distance goes on decreasing. At high value of differential gain 2.5 × 10 -16 cm 2 for the transmission distance 1050 km, all channels produce inter channel crosstalk with bit error rate greater than 10 -6 . But for lower differential gain 190 atto cm 2 , the quality of all channel increases at the cost of large power penalty. With slight increase in differential gain 200 atto cm 2 , the maximum transmission distance observed is 4550 km with quality of received signal more than 15 dB and having nil power penalty. We observed clear eye diagrams and optical power spectra for received signal with transmission distance 1050 km and 4550 km using soliton RZ-DPSK system. The bit error rate for all channels increase more than 10 -10 with the increase in launched input power that is due to power saturation. [ABSTRACT FROM AUTHOR]

In this article, the simulation results have been presented for dispersive optical communication with different electrical drivers. The length of single-mode fiber has been put in a run that is compensated by dispersion-compensated fiber. The results have been presented and it is observed that of all the electrical drivers, the NRZ rectangular is best suited for dispersive optical communication systems. For this electrical driver, the parameters like BER remain constant and tow. For other drivers, the RER decreases more for RZ super-Gaussian. Similarly, the Q factor increases with runs for all types of drivers except for NRZ rectangular, for which it decreases. For all the drivers, it is clear that as the runs are varied, the eye opening penalty increases, that is, there is eye opening as the length of single-mode fiber is increased. It is also seen that the dispersion-compensated fiber compensates for the dispersion very effectively irrespective of the type of driver. Of the two formats, return to zero (RZ) and non-return to zero (NRZ), the earlier has more eye-opening penalty as the distortion is more and is clearly visible in all the rectangular, super-Gaussian, and raised cosine RZ formats. Of the three RZ formats, it is observed that RZ rectangular has the least eye-opening penalty. The non-return to zero format has less distortion and, of the two rectangular and raised cosine, the NRZ rectangular has less eye-opening penalty. [ABSTRACT FROM AUTHOR]

The coupling of light from a number of few or single-moded fibers into a single multi-mode fiber is analyzed using geometric optics, and simple results demonstrating mode conservation are derived. Coupling from multiple single-mode fibers into a multi-mode fiber is investigated in detail using the overlap integral to determine coupling into each mode of the output fiber as a function of the light phase in the inputs. As well as results with practical relevance to fiber tapped delay-line filters and optical CDMA, the analysis provides pedagogic insight into light propagation and the light-gathering properties of fiber. [ABSTRACT FROM AUTHOR]

The recent research and development results of the Photonic Engineering Group in the photonic sensing field are reported. This article includes a sample of contributions in several of the ongoing R&D lines: fiber sensing using Bragg grating technology; gas sensing, high temperature monitoring; optoelectronic instrumentation for laser welding monitoring; fiber active devices; and, finally, on sensing technology using plastic optical fiber. [ABSTRACT FROM AUTHOR]