Search

'Smart' bandages based on multimodal wearable devices could enable real-time physiological monitoring and active intervention to promote healing of chronic wounds. However, there has been limited development in incorporation of both sensors and stimulators for the current smart bandage technologies. Additionally, while adhesive electrodes are essential for robust signal transduction, detachment of existing adhesive dressings can lead to secondary damage to delicate wound tissues without switchable adhesion. Here we overcome these issues by developing a flexible bioelectronic system consisting of wirelessly powered, closed-loop sensing and stimulation circuits with skin-interfacing hydrogel electrodes capable of on-demand adhesion and detachment. In mice, we demonstrate that our wound care system can continuously monitor skin impedance and temperature and deliver electrical stimulation in response to the wound environment. Across preclinical wound models, the treatment group healed ~25% more rapidly and with ~50% enhancement in dermal remodeling compared with control. Further, we observed activation of proregenerative genes in monocyte and macrophage cell populations, which may enhance tissue regeneration, neovascularization and dermal recovery. A wireless 'smart' bandage stimulates wound healing. [ABSTRACT FROM AUTHOR]

Triboelectric nanogenerators (TENGs) utilize the phenomena of contact electrification and electrostatic induction to harvest mechanical energy from the environment. A good match between the motion frequency and the circuit characteristic frequency is critical for the effective power generation of a TENG. However, most TENGs have a time-dependent inherent capacitance (TIC-TENG), which hinders an optimal design for efficient energy conversion. Here, we propose a novel structure of a TENG with a constant inherent capacitance (CIC-TENG) and a mathematical model is established to provide analytical expressions of key output parameters of the device, which gives numerical simulation results that are in good agreement with the experimentally obtained results. Figures of merit and an optimization strategy are also given as guidelines for the optimization of material selection, geometry design, etc. Furthermore, a disk-formed CIC-TENG (DCIC-TENG) with polarity-switched triboelectric pairs is constructed to harvest unidirectional mechanical energy continuously, achieving an output power density of 55 mW/m2. The effects of the motion frequency, the number of electrodes and triboelectric pairs on the charge transfer efficiency of the DCIC-TENG are assessed and a preferred design strategy is given. Finally, the CIC-TENG demonstrates approximately two-fold advantages in power transfer efficiency over the TIC-TENG, and a DCIC-TENG-based self-powered anemometer was fabricated to measure wind speed in real time. [ABSTRACT FROM AUTHOR]

Neurotransmitters play essential roles in regulating neural circuit dynamics both in the central nervous system as well as at the peripheral, including the gastrointestinal tract1–3. Their real-time monitoring will offer critical information for understanding neural function and diagnosing disease1–3. However, bioelectronic tools to monitor the dynamics of neurotransmitters in vivo, especially in the enteric nervous systems, are underdeveloped. This is mainly owing to the limited availability of biosensing tools that are capable of examining soft, complex and actively moving organs. Here we introduce a tissue-mimicking, stretchable, neurochemical biological interface termed NeuroString, which is prepared by laser patterning of a metal-complexed polyimide into an interconnected graphene/nanoparticle network embedded in an elastomer. NeuroString sensors allow chronic in vivo real-time, multichannel and multiplexed monoamine sensing in the brain of behaving mouse, as well as measuring serotonin dynamics in the gut without undesired stimulations and perturbing peristaltic movements. The described elastic and conformable biosensing interface has broad potential for studying the impact of neurotransmitters on gut microbes, brain–gut communication and may ultimately be extended to biomolecular sensing in other soft organs across the body.NeuroString, a tissue-like biological interface created by laser patterning of polyimide into a graphene/nanoparticle network embedded in an elastomer, is introduced, allowing in vivo real-time detection of neurotransmitters in the brain and gut. [ABSTRACT FROM AUTHOR]

Next-generation light-emitting displays on skin should be soft, stretchable and bright1–7. Previously reported stretchable light-emitting devices were mostly based on inorganic nanomaterials, such as light-emitting capacitors, quantum dots or perovskites6–11. They either require high operating voltage or have limited stretchability and brightness, resolution or robustness under strain. On the other hand, intrinsically stretchable polymer materials hold the promise of good strain tolerance12,13. However, realizing high brightness remains a grand challenge for intrinsically stretchable light-emitting diodes. Here we report a material design strategy and fabrication processes to achieve stretchable all-polymer-based light-emitting diodes with high brightness (about 7,450 candela per square metre), current efficiency (about 5.3 candela per ampere) and stretchability (about 100 per cent strain). We fabricate stretchable all-polymer light-emitting diodes coloured red, green and blue, achieving both on-skin wireless powering and real-time displaying of pulse signals. This work signifies a considerable advancement towards high-performance stretchable displays.A material design strategy and fabrication process is described to produce all-polymer light-emitting diodes with high brightness, current efficiency and good mechanical stability, with applications in skin electronics and human–machine interfaces. [ABSTRACT FROM AUTHOR]

Skin-like intrinsically stretchable soft electronic devices are essential to realize next-generation remote and preventative medicine for advanced personal healthcare1–4. The recent development of intrinsically stretchable conductors and semiconductors has enabled highly mechanically robust and skin-conformable electronic circuits or optoelectronic devices2,5–10. However, their operating frequencies have been limited to less than 100 hertz, which is much lower than that required for many applications. Here we report intrinsically stretchable diodes—based on stretchable organic and nanomaterials—capable of operating at a frequency as high as 13.56 megahertz. This operating frequency is high enough for the wireless operation of soft sensors and electrochromic display pixels using radiofrequency identification in which the base-carrier frequency is 6.78 megahertz or 13.56 megahertz. This was achieved through a combination of rational material design and device engineering. Specifically, we developed a stretchable anode, cathode, semiconductor and current collector that can satisfy the strict requirements for high-frequency operation. Finally, we show the operational feasibility of our diode by integrating it with a stretchable sensor, electrochromic display pixel and antenna to realize a stretchable wireless tag. This work is an important step towards enabling enhanced functionalities and capabilities for skin-like wearable electronics.A stretchable anode, cathode, semiconductor and current collector have been developed to create stretchable diodes that can operate at megahertz frequencies for use in wirelessly operated, skin-like wearable electronics. [ABSTRACT FROM AUTHOR]

Skin-like electronics that can adhere seamlessly to human skin or within the body are highly desirable for applications such as health monitoring, medical treatment, medical implants and biological studies, and for technologies that include human-machine interfaces, soft robotics and augmented reality. Rendering such electronics soft and stretchable-like human skin-would make them more comfortable to wear, and, through increased contact area, would greatly enhance the fidelity of signals acquired from the skin. Structural engineering of rigid inorganic and organic devices has enabled circuit-level stretchability, but this requires sophisticated fabrication techniques and usually suffers from reduced densities of devices within an array. We reasoned that the desired parameters, such as higher mechanical deformability and robustness, improved skin compatibility and higher device density, could be provided by using intrinsically stretchable polymer materials instead. However, the production of intrinsically stretchable materials and devices is still largely in its infancy: such materials have been reported, but functional, intrinsically stretchable electronics have yet to be demonstrated owing to the lack of a scalable fabrication technology. Here we describe a fabrication process that enables high yield and uniformity from a variety of intrinsically stretchable electronic polymers. We demonstrate an intrinsically stretchable polymer transistor array with an unprecedented device density of 347 transistors per square centimetre. The transistors have an average charge-carrier mobility comparable to that of amorphous silicon, varying only slightly (within one order of magnitude) when subjected to 100 per cent strain for 1,000 cycles, without current-voltage hysteresis. Our transistor arrays thus constitute intrinsically stretchable skin electronics, and include an active matrix for sensory arrays, as well as analogue and digital circuit elements. Our process offers a general platform for incorporating other intrinsically stretchable polymer materials, enabling the fabrication of next-generation stretchable skin electronic devices. [ABSTRACT FROM AUTHOR]

In this study, the discharge voltage behavior of electric double-layer capacitors (EDLCs) during high- g impact is studied both theoretically and experimentally. A micro-scale dynamic mechanism is proposed to describe the physical basis of the increase in the discharge voltage during a high- g impact. Based on this dynamic mechanism, a multi-field model is established, and the simulation and experimental studies of the discharge voltage increase phenomenon are conducted. From the simulation and experimental data, the relationship between the increased voltage and the high- g acceleration is revealed. An acceleration detection range of up to 10,000 g is verified. The design of the device is optimized by studying the influences of the parameters, such as the electrode thickness and discharge current, on the outputs. This work opens up new avenues for the development of autonomous sensor systems based on energy storage devices and is significant for many practical applications such as in collision testing and automobile safety. [ABSTRACT FROM AUTHOR]

Parasitic capacitance is an unavoidable and usually unwanted capacitance that exists in electric circuits, and it is the most important second-order non-ideal effect that must be considered while designing a triboelectric nanogenerator (TENG) because its magnitude is comparable to the magnitude of the TENG capacitance. This paper investigates the structure and performance optimization of TENGs through modeling and simulation, taking the parasitic capacitance into account. Parasitic capacitance is generally found to cause severe performance degradation in TENGs, and its effects on the optimum matching resistance, maximum output power, and structural figures-of-merit (FOMs) of TENGs are thoroughly investigated and discussed. Optimum values of important structural parameters such as the gap and electrode length are determined for the different working modes of TENGs, systematically demonstrating how these optimum structural parameters change as functions of the parasitic capacitance. Additionally, it is demonstrated that the parasitic capacitance can improve the height tolerance of the metal freestanding-mode TENGs. This work provides a theoretical foundation for the structure and performance optimization of TENGs for practical applications and promotes the development of mechanical energy-harvesting techniques. [ABSTRACT FROM AUTHOR]

The process of charge transfer based on triboelectrification (TE) and contact electrification (CE) has been recently utilized as the basis for a new and promising energy harvesting technology, i.e., triboelectric nanogenerators, as well as selfpowered sensors and systems. The electrostatic charge transfer between two surfaces can occur in both the TE and the CE modes depending on the involvement of relative sliding friction. Does the sliding behavior in TE induce any fundamental difference in the charge transfer from the CE? Few studies are available on this comparison because of the challenges in ruling out the effect of the contact area using traditional macro-scale characterization methods. This paper provides the first study on the fundamental differences in CE and TE at the nanoscale based on scanning probe microscopic methods. A quantitative comparison of the two processes at equivalent contact time and force is provided, and the results suggest that the charge transfer from TE is much faster than that from CE, but the saturation value of the transferred charge density is the same. The measured frictional energy dissipation of ∼11 eV when the tip scans over distance of 1 Å sheds light on a potential mechanism: The friction may facilitate the charge transfer process via electronic excitation. These results provide fundamental guidance for the selection of materials and device structures to enable the TE or the CE in different applications; the CE mode is favorable for frequent moderate contact such as vibration energy harvesting and the TE mode is favorable for instant movement such as harvesting of energy from human walking. [ABSTRACT FROM AUTHOR]

Human biomechanical energy is characterized by fluctuating amplitudes and variable low frequency, and an effective utilization of such energy cannot be achieved by classical energyharvesting technologies. Here we report a high-efficient self-charging power system for sustainable operation of mobile electronics exploiting exclusively human biomechanical energy, which consists of a high-output triboelectric nanogenerator, a power management circuit to convert the random a.c. energy to d.c. electricity at 60% efficiency, and an energy storage device. With palm tapping as the only energy source, this power unit provides a continuous d.c. electricity of 1.044mW (7.34Wm ― 3) in a regulated and managed manner. This self-charging unit can be universally applied as a standard ‘infinite-lifetime’ power source for continuously driving numerous conventional electronics, such as thermometers, electrocardiograph system, pedometers, wearable watches, scientific calculators and wireless radio-frequency communication system, which indicates the immediate and broad applications in personal sensor systems and internet of things. [ABSTRACT FROM AUTHOR]

The piezoelectric characteristics of nanowires, thin films and bulk crystals have been closely studied for potential applications in sensors, transducers, energy conversion and electronics. With their high crystallinity and ability to withstand enormous strain, two-dimensional materials are of great interest as high-performance piezoelectric materials. Monolayer MoS2 is predicted to be strongly piezoelectric, an effect that disappears in the bulk owing to the opposite orientations of adjacent atomic layers. Here we report the first experimental study of the piezoelectric properties of two-dimensional MoS2 and show that cyclic stretching and releasing of thin MoS2 flakes with an odd number of atomic layers produces oscillating piezoelectric voltage and current outputs, whereas no output is observed for flakes with an even number of layers. A single monolayer flake strained by 0.53% generates a peak output of 15 mV and 20 pA, corresponding to a power density of 2 mW m−2 and a 5.08% mechanical-to-electrical energy conversion efficiency. In agreement with theoretical predictions, the output increases with decreasing thickness and reverses sign when the strain direction is rotated by 90°. Transport measurements show a strong piezotronic effect in single-layer MoS2, but not in bilayer and bulk MoS2. The coupling between piezoelectricity and semiconducting properties in two-dimensional nanomaterials may enable the development of applications in powering nanodevices, adaptive bioprobes and tunable/stretchable electronics/optoelectronics. [ABSTRACT FROM AUTHOR]

MoO nanobelts (NBs) having different properties have been synthesized via a physical vapor deposition (PVD) method. The crystallographic structures and morphologies of the NBs were characterized by X-ray diffraction, transmission electron microscopy and scanning electron microscopy. Electrical measurements were performed and the profound piezoresistive effect in MoO experimentally studied and verified. Factors that influence the gauge factor, such as NB size, doping concentration and atmosphere composition, are discussed and analyzed. Gas sensing performance was also tested in devices and it was demonstrated that by applying strain to the gas sensor, its sensing performance could be effectively tuned and enhanced. This study provides the first demonstration of significant piezoresistivity in MoO NBs and the first illustration of a generic mechanism by means of which this effect can be coupled with other electronic modulation measures to afford better device performance and broader material functionality. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

Emulation of the sensation of touch through high-resolution electronic means could become important in future generations of robotics and human-machine interfaces. Here, we demonstrate that a nanowire light-emitting diode-based pressure sensor array can map two-dimensional distributions of strain with an unprecedented spatial resolution of 2.7 µm, corresponding to a pixel density of 6,350 dpi. Each pixel is composed of a single n-ZnO nanowire/p-GaN light-emitting diode, the emission intensity of which depends on the local strain owing to the piezo-phototronic effect. A pressure map can be created by reading out, in parallel, the electroluminescent signal from all of the pixels with a time resolution of 90 ms. The device may represent a major step towards the digital imaging of mechanical signals by optical means, with potential applications in artificial skin, touchpad technology, personalized signatures, bio-imaging and optical microelectromechanical systems. [ABSTRACT FROM AUTHOR]