Search

Introduction: We hypothesized that engineering a combined lymph node/melanoma organoid from the same patient would allow tumor, stroma, and immune system to remain viable for personalized immunotherapy screening. Methods: Surgically obtained matched melanoma and lymph node biospecimens from the same patient were transferred to the laboratory and washed with saline, antibiotic, and red blood cell lysis buffer. Biospecimens were dissociated, incorporated into an extracellular matrix (ECM)-based hydrogel system, and biofabricated into three dimensional (3D) mixed melanoma/node organoids. Cells were not sorted, so as to preserve tumor heterogeneity, including stroma and immune cell components, resulting in immune-enhanced patient tumor organoids (iPTOs). Organoid sets were screened in parallel with nivolumab, pembrolizumab, ipilimumab, and dabrafenib/trametinib for 72 h. LIVE/DEAD staining and quantitative metabolism assays recorded relative drug efficacy. Histology and immunohistochemistry were used to compare tumor melanoma cells with organoid melanoma cells. Lastly, node-enhanced iPTOs were employed to activate patient-matched peripheral blood T cells for killing of tumor cells in naïve PTOs. Results: Ten biospecimen sets obtained from eight stage III and IV melanoma patients were reconstructed as symbiotic immune/tumor organoids between September 2017 and June 2018. Successful establishment of viable organoid sets was 90% (9/10), although organoid yield varied with biospecimen size. Average time from organoid development to initiation of immunotherapy testing was 7 days. In three patients for whom a node was not available, it was substituted with peripheral blood mononuclear cells. iPTO response to immunotherapy was similar to specimen clinical response in 85% (6/7) patients. In an additional pilot study, peripheral T cells were circulated through iPTOs, and subsequently transferred to naïve PTOs from the same patient, resulting in tumor killing, suggesting a possible role of iPTOs in generating adaptive immunity. Conclusion: Development of 3D mixed immune-enhanced tumor/node organoids is a feasible platform, allowing individual patient immune system and tumor cells to remain viable for studying of personalized immunotherapy response. [ABSTRACT FROM AUTHOR]

To support the increasing translational use of transplanted cells, there is a need for high-throughput cell encapsulation technologies. Microfluidics is a particularly promising candidate technology to address this need, but conventional polydimethylsiloxane devices have encountered challenges that have limited their utility, including clogging, leaking, material swelling, high cost, and limited scalability. Here, we use a rapid prototyping approach incorporating patterned adhesive thin films to develop a reusable microfluidic device that can produce alginate hydrogel microbeads with high-throughput potential for microencapsulation applications. We show that beads formed in our device have high sphericity and monodispersity. We use the system to demonstrate effective cell encapsulation of mesenchymal stem cells and show that they can be maintained in culture for at least 28 days with no measurable reduction in viability. Our approach is highly scalable and will support diverse translational applications of microencapsulated cells. [ABSTRACT FROM AUTHOR]

Introduction: We have hypothesized that biofabrication of appendiceal tumor organoids allows for a more personalized clinical approach and facilitates research in a rare disease.Methods: Appendiceal cancer specimens obtained during cytoreduction with hyperthermic intraperitoneal chemotherapy procedures (CRS/HIPEC) were dissociated and incorporated into an extracellular matrix-based hydrogel system as three-dimensional (3D), patient-specific tumor organoids. Cells were not sorted, preserving tumor heterogeneity, including stroma and immune cell components. Following establishment of organoid sets, chemotherapy drugs were screened in parallel. Live/dead staining and quantitative metabolism assays recorded which chemotherapies were most effective in killing cancer cells for a specific patient. Maintenance of cancer phenotypes were confirmed by using immunohistochemistry.Results: Biospecimens from 12 patients were applied for organoid development between November 2016 and May 2018. Successful establishment rate of viable organoid sets was 75% (9/12). Average time from organoid development to chemotherapy testing was 7 days. These tumors included three high-grade appendiceal (HGA) and nine low-grade appendiceal (LGA) primaries obtained from sites of peritoneal metastasis. All tumor organoids were tested with chemotherapeutic agents exhibited responses that were either similar to the patient response or within the variability of the expected clinical response. More specifically, HGA tumor organoids derived from different patients demonstrated variable chemotherapy tumor-killing responses, whereas LGA organoids tested with the same regimens showed no response to chemotherapy. One LGA set of organoids was immune-enhanced with cells from a patient-matched lymph node to demonstrate feasibility of a symbiotic 3D reconstruction of a patient matched tumor and immune system component.Conclusions: Development of 3D appendiceal tumor organoids is feasible even in low cellularity LGA tumors, allowing for individual patient tumors to remain viable for research and personalized drug screening. [ABSTRACT FROM AUTHOR]

The field of regenerative medicine has progressed tremendously over the past few decades in its ability to fabricate functional tissue substitutes. Conventional approaches based on scaffolding and microengineering are limited in their capacity of producing tissue constructs with precise biomimetic properties. Three-dimensional (3D) bioprinting technology, on the other hand, promises to bridge the divergence between artificially engineered tissue constructs and native tissues. In a sense, 3D bioprinting offers unprecedented versatility to co-deliver cells and biomaterials with precise control over their compositions, spatial distributions, and architectural accuracy, therefore achieving detailed or even personalized recapitulation of the fine shape, structure, and architecture of target tissues and organs. Here we briefly describe recent progresses of 3D bioprinting technology and associated bioinks suitable for the printing process. We then focus on the applications of this technology in fabrication of biomimetic constructs of several representative tissues and organs, including blood vessel, heart, liver, and cartilage. We finally conclude with future challenges in 3D bioprinting as well as potential solutions for further development. [ABSTRACT FROM AUTHOR]