Search

The demand for dissimilar joining of steel grades, namely austenitic stainless steels to low-alloy steels, may increase in near future owing to the fact that the storing of LNG is currently becoming a necessity, particularly in Europe, due to the shortage of supply or interruptions in the supply. Therefore, successful dissimilar joining of steel grades using traditional fusion welding techniques in such applications is required. In this study, butt-welded joints of AISI 316L austenitic steel and low-alloy steel plates (containing 9% Ni) of 10 mm thickness were fabricated by gas tungsten arc welding employing a Ni-based filler wire. The microstructure and mechanical properties of the weldment were examined by detailed optical microscopy, extensive micro-hardness measurements, and tensile tests. Further, fracture toughness of the joint at cryogenic temperatures (− 196 °C) was also determined by Charpy impact test. The dissimilar joint exhibited a high tensile strength of 633 MPa, which is higher than that of the lower-strength AISI 316L base plate (about 600 MPa), while its elongation (21%) was much lower due to confined plasticity. The lowest impact energy was displayed by HAZ-F notched specimens, namely about 62.6 J (0.83 J/mm2). However, it is still reasonably above the minimum impact energy specified for the LNG storage tanks, i.e., 0.75 J/mm2. [ABSTRACT FROM AUTHOR]

The aim of this work is to investigate the mechanical properties and microstructures of friction-stir welded (FSWed) St52 structural steel joints. In this study, St52 steel plates with a thickness of 4 mm were butt-welded by friction-stir welding (FSW) using a tungsten carbide tool having a conical pin. The microstructure of the welded zone consists of equiaxed fine ferrite, grain boundary ferrite, Widmanstatten ferrite, and aggregates of ferrite + cementite. The microhardness measurements showed that the hardness of the welded zone was significantly higher than that of the base metal. The FSWed St52 joint exhibited a significant strength overmatching in the weld region and a strength performance similar to or slightly higher than that of the base plate. [ABSTRACT FROM AUTHOR]

The mass saving potential of light-weight materials, such as Al alloys, is beneficial for fuel economy and reducing CO emissions. However, the wide-spread use of these alloys has been long hindered due to the difficulty in fusion joining as well as their high cost. Welding of Al alloys, which are considered to be difficult to weld through conventional arc welding, is now possible by either of low heat input arc welding, high-power density fusion joining, such as laser beam welding and electron beam welding, or friction stir welding. Particularly, friction stir welding can be successfully applied to these materials owing to the fact that no melting takes place in the weld nugget. The aim of this overview is to summarize the developments in the joining of Al alloys over the recent years. This study is also intended to provide guidance for the industry and researchers dealing with joining of these alloys. [ABSTRACT FROM AUTHOR]

In this study, dissimilar AA7075-O/6061-O and AA7075-T6/6061-T6 butt joints were produced by friction stir welding (FSW), and postweld heat treatment (PWHT) was applied to the joints obtained. The effects of initial temper condition and PWHT on the microstructure and mechanical properties of the dissimilar joints were thus investigated. It was demonstrated that sound dissimilar joints can be produced for both temper conditions. A hardness increase in the joint area ( i.e., strength overmatching) was obtained in the joints produced in the O-temper condition, whereas a hardness loss was observed in the joint area of the joints obtained in the T6 temper condition. It was also well demonstrated that PWHT could be used in order to improve the joint properties for both O and T6 joints provided that the joint is defect-free prior to subsequent heat treatment. [ABSTRACT FROM AUTHOR]

The diversity and never-ending desire for a better life standard result in a continuous development of the existing manufacturing technologies. In line with these developments in the existing production technologies the demand for more complex products increases, which also stimulates new approaches in production routes of such products, e.g., novel welding procedures. For instance, the friction stir welding (FSW) technology, developed for joining difficult-to-weld Al-alloys, has been implemented by industry in manufacturing of several products. There are also numerous attempts to apply this method to other materials beyond Al-alloys. However, the process has not yet been implemented by industry for joining these materials with the exception of some limited applications. The microstructures and mechanical properties of friction stir welded Al-alloys existing in the open literature will be discussed in detail in this review. The correlations between weld parameters used during FSW and the microstructures evolved in the weld region and thus mechanical properties of the joints produced will be highlighted. However, the modeling studies, material flow, texture formation and developments in tool design are out of the scope of this work as well as the other variants of this technology, such as friction stir spot welding (FSSW). [ABSTRACT FROM AUTHOR]

In this study, the effect of post-weld heat treatment (PWHT) on the microstructure and mechanical properties of friction stir butt-joined AA6061 Al-alloy plates both in O and T6-temper conditions was investigated by detailed microstructural investigations and microhardness measurements, in combination with transverse tensile testing. It was determined that the PWHT might result in abnormal grain growth (AGG) in the weld zone particularly in the joints produced in O-temper condition depending on the weld parameters used during friction stir welding. The PWHT generally led to an improvement in the mechanical properties even if AGG took place. Thus, the post-weld heat-treated joints exhibited mechanical properties much higher than those of respective as-welded plates and comparable to those of the respective base plates. [ABSTRACT FROM AUTHOR]

In this study, AA7075-O and AA7075-T6 Al alloy plates were friction stir butt welded using two sets of weld parameters in order to investigate the effects of temper condition prior to joining and post weld heat treatment on microstructure and mechanical properties of the joints. Another goal of the work is to determine the possibility of restoring the loss of strength in the joint area experienced in welding of this alloy in the age-hardened condition by subsequent heat treatment. The study revealed that the friction stir welding resulted in a strength undermatching when the alloy joined in T6 condition while a significant strength overmatching was obtained in the joints produced in O temper condition. The post weld heat treatment led to a significant recovery in the strength of the joints produced in T6 condition, thus a significant increase in the joint performance. On the other hand, it led to a decrease in the joint performance value of the joints produced in O temper condition although the strength was increased. Furthermore, the post weld heat treatment resulted in abnormal grain growth in the joint area the degree of which depends on weld parameters used and the prior temper condition. [ABSTRACT FROM AUTHOR]