Search

The production of paper is a key component for global civilization. Around 300 million tonnes of paper are produced every day globally, with matured pulpwood being the major contributor. Due to rising demand for paper and the depletion of available wood resources, researchers are now focused on finding alternative non-wood resources that are suitable for pulp and paper production. The current study aims to produce eco-friendly and biodegradable paper using a combination of Eichhornia crassipes (water hyacinth) and dried flowers. Water hyacinth is considered as a lignocellulose plant which contains 57% lignocellulose, and dried flower contains 40% cellulose, which is the prime source for paper production. Various sections of water hyacinth, including wet and dry petiole, leaves, and root, were blended with dried flowers through the soda process. Then, the physical properties and FTIR analysis was carried out to identify the quality of the paper produced. The paper produced from root and dried petiole has a lower thickness (1.0 mm and 0.5 mm) than other mix proportions. The opacity of the leaves was found to be 0.5% (light passing) and for the root 0.7% (light passing). Also, the dry petiole and root paper have a good dry tensile strength of 1.30Kpa and 1.20Kpa, respectively. Hence, paper made from dry petiole and root was found to be efficient and suitable for the paper industry. [ABSTRACT FROM AUTHOR]

The study describes the preparation of nanocellulose from organosolv hemp pulp and its application in the production of food packaging paper as an alternative to petroleum products. OHP was obtained from renewable plant materials hemp fibers by extraction with NaOH solution and cooking using a mixture of acetic acid and hydrogen peroxide. A stable transparent nanocellulose gel was extracted from OHP by acid hydrolysis followed by ultrasonic treatment. It was found that an increase in the consumption of sulfuric acid, temperature and duration of the OHP hydrolysis process improved the quality indicators of hemp nanocellulose. A linear dependence of the tensile strength and transparency of nanocellulose films on their density has been established. Morphological (SEM), structural (FTIR and XRD) and thermal analysis (TGA) of hemp fibers, OHP and nanocellulose were carried out. Nanocellulose films had a density of up to 1.56 g/cm3, a tensile strength of up to 66.7 MPa, a transparency of up to 87.3%. Atomic force microscopy method showed that the transverse dimension of nanocellulose particles is from 8 to 23 nm. Hemp nanocellulose had a higher crystallinity index (87.2%) than OHP (72.0%), but lower thermal stability. The positive effect of adding nanocellulose from hemp on improving all quality parameters of paper for food packaging has been shown. The addition of 2% hemp nanocellulose makes it possible to obtain paper that exceeds the breaking force requirements of premium grade paper by 40%, and the breaking length increases by 42% compared to paper without chemical additives. [ABSTRACT FROM AUTHOR]

Superhydrophobic and strong cellulosic paper was fabricated in a two-step process consisting of heavy refining and dip coating with PDMS (trimethylsiloxy-terminated poly (dimethylsiloxane)) and Hf-SiO2 (hydrophobic fumed silica) solution. Results showed that the heavy refining produced extensive fibrillated fibers, which significantly increased the tensile strength. Meanwhile, the density of the paper sheet increased, and the porosity decreased. Benefiting from these changes, the subsequent dip coating operation was improved, producing paper with a very high water contact angle (WCA), yet with a low up-take of the hydrophobic solution. Finally, superhydrophobic paper sheets were fabricated with 155o WCA and 1o sliding angle (SA). At the same time, its tensile strength increased by 12.7 fold (from 0.85 MPa of the original paper to 10.8 MPa), with additional benefits, such as high transparency (75% at 550 nm). The superhydrophobic and strong paper is highly desirable for high value-added utilization of fiber. [ABSTRACT FROM AUTHOR]

This contribution focuses on understanding of paper wet-strength properties, by taking a closer look at the spatial distribution of wet-strengthening polymers inside the cellulosic fiber network deposited under different treatment conditions using confocal laser scanning microscopy as in situ imaging tool. We compare the behavior of paper samples treated with a photochemically cross-linkable copolymer using an impregnation process employing three different solvents, namely water, 2-propanol (IPA) and 1-butanol (BuOH), respectively. As these solvents swell paper fibers to quite different extents, the deposition of the polymer, on, in or in-between the cellulosic fibers varies quite strongly, as is shown by in-depth analysis using confocal laser scanning microscopy. The difference in accessibility of distinct surface sites exclusively on or also in and between the fibers controls the macroscopic tensile strength under both dry and wet conditions. [ABSTRACT FROM AUTHOR]

The influence of strain during drying is known to have a large effect on its mechanical properties like tensile strength, Young's modulus and hygroexpansion. In this study we investigate free and restrained dried paper and investigate the relation between the paper microstructure and its mechanical properties. The first part of the work investigates the development of the mechanical properties as well as paper internal stresses and strains (elastic-, inelastic- and hygrostrain) at different moisture contents during the drying process. Emphasis is put on the changes of hygrostrains and the paper hygroexpansion coefficient during drying. One main finding was that in constrained drying the drying stresses are considerably below the yield stress and, as a consequence, the deformations are mainly inelastic (creep) and only marginally elastic. In the second part we are analyzing the microstructure of free and restrained dried sheets by X-ray microtomography (μ -CT). From the μ -CT analysis relevant network parameters such as number of contact points, fiber bond area, free fiber length and fiber curl were extracted. Also a novel method to investigate the interface angle of the fibers in the vicinity of the bond sites was established. The results showed that the major difference from the drying procedure manifests itself in the out-of-plane curl of the fibers. Statistically number of contact points, bond area and in-plane curl were not different whereas in-plane curl and free fiber length were different. The interface angle appears to be slightly affected by the drying procedure but is overall very low. [ABSTRACT FROM AUTHOR]

In this work, tension and fracture behaviors of cellulose nanopaper (CNP) made from two different preparation approaches are comparatively studied. The CNP are prepared by casting (or C-CNP) and filtration (or F-CNP) of CNF suspension. The resulting CNP are mechanically characterized using the vision-based full-field optical method of Digital Image Correlation. Tension tests show that F-CNP has a higher strength and greater nonlinearity than the C-CNP. The crack initiation and growth characteristics of the two types of CNP are investigated using optical measurements. The data are analyzed under small-scale-yielding conditions to quantify the fracture parameters such as stress intensity factors and energy release rates at crack initiation as well as during crack growth. The results indicate that both C-CNP and F-CNP show significant crack growth resistance in the post-crack initiation regime. The F-CNP particularly offers substantial resistance to crack growth relative to the C-CNP demonstrating that filtration is the preferred method to make CNP with higher tensile strength and better fracture properties. [ABSTRACT FROM AUTHOR]

To protect forest resources and increase the value of agro-industrial residues, it would be helpful to produce paper-based materials from non-woody or recycled fiber resources. This study investigated the reinforcement mechanism of bacterial cellulose (BC) on paper sheets made from different sources including softwood, hardwood, sugarcane bagasse, bamboo, wheat straw, and recycled fiber, which represent a selection of high quality, medium quality, and low quality fibers. The results showed that by maintaining BC addition at a low level of 0.5-1.5% (total paper dry weight), the paper sheets made from high and medium quality fibers have the maximum tensile index improvement, with 5-25%. The tensile index of low quality fiber including wheat straw pulp and recycled fiber pulp increased slightly and gradually with the level of BC addition; at 5% BC addition, the tensile indexes increased by 9 and 40%, respectively. To investigate the BC reinforcement mechanism, different fiber characteristics, SEM images of BC reinforced paper, BC retention rate on paper, and the effects of dispersant addition were evaluated. It was found that high BC addition or retention rate in paper sheets do not necessarily result in good BC reinforcement effects but that proper dispersion of BC is important. [ABSTRACT FROM AUTHOR]

Chemically modified cellulose micro- and nanofibrils were successfully used as paper strength additives. Three different kinds of cellulose nanofibrils (CNFs) were studied: carboxymethylated CNFs, periodate-oxidised carboxymethylated CNFs and dopamine-grafted carboxymethylated CNFs, all prepared from bleached chemical fibres of dissolving grade, and one microfibrillated cellulose from unbleached kraft fibres. In addition to mechanical characterization of the final paper sheets the fibril retention, sheet density and sheet morphology were also studied as a function of addition of the four different cellulose fibrils. In general, the cellulose fibrils, when used as additives, significantly increased the tensile strength, Young's modulus and strain-at-break of the paper sheets. The effects of the different fibrils on these properties were compared and evaluated and used to analyse the underlying mechanisms behind the strengthening effect. The strength-enhancing effect was most pronounced for the periodate-oxidised CNFs when they were added together with polyvinyl amine (PVAm) or poly(dimethyldiallylammonium chloride) (pDADMAC). The addition of periodate-oxidised CNFs, with pDADMAC as retention aid, resulted in a 37% increase in tensile strength at a 2 wt% addition and an 89% increase at a 15 wt% addition (from 67 to 92 and 125 kNm/kg, respectively) compared to a reference with only pDADMAC. Wet-strong sheets with a wet tensile index of 30 kNm/kg were also obtained when periodate-oxidised CNFs and PVAm were combined. This significant increase in wet strength is suggested to be the result of a formation of cross-links between the aldehyde groups, introduced by the periodate oxidation, and hydroxyl groups on the lignocellulosic fibres and the primary amines of PVAm. Even though less significant, there was also an increase in wet tensile strength when pDADMAC was used together with periodate-oxidised fibrils which shows that the aldehyde groups are able to increase the wet strength without the presence of the primary amines of the PVAm. As an alternative method to strengthen the fibre network, carboxymethylated CNFs grafted with dopamine, by an ethyl dimethylaminopropyl carbodiimide coupling, were used as a strength additive. When used as an additive, these CNFs showed a strong propensity to form films on and around the fibres and significantly increased the mechanical properties of the sheets. Their addition resulted in an increase in the Young´s modulus by 41%, from 5.1 to 7.2 GPa, and an increase in the tensile strength index of 98% (from 53 to 105 kNm/kg) with 5 wt% retained dopamine-grafted CNFs. [ABSTRACT FROM AUTHOR]

In industrial applications, such as paper and nonwovens, cellulose fibers are used in the form of a network where the fibers are oriented more or less in the sheet-plane direction. However, in many biological systems, fibers are instead oriented in a three-dimensional (3D) space, creating a wide variety of functionalities. In this study we created a 3D-oriented fiber network on the laboratory scale and have identified some unique features of its structure and mechanical properties. The 3D fiber network sheets were prepared by using foam-forming as well as modifying consolidation and drying procedures. The fiber orientation and tensile/compression behavior were determined. The resulting sheets were extremely bulky (above 190 cm/g) and had extremely low stiffness (or high softness) compared to the reference handsheets. Despite this high bulk, the sheets retained good structural integrity. We found that a 3D-oriented fiber network requires much less fiber-fiber contact to create a connected ('percolated') network than a two-dimensionally oriented network. The compression behavior in the thickness direction was also unique, characterized by extreme compressibility because of its extreme bulk and a long initial increase in the compression load as well as high strain recovery after compression because of its fiber reorientation during compression. [ABSTRACT FROM AUTHOR]

In the present work the evolution of physical and mechanical properties of papers and nanopapers is studied. Handsheets made of eucalyptus fibres reinforced with 0, 25, 50, 75 and 100 wt% of nanofibrillated cellulose (NFC) content were fabricated using a Rapid Köthen-like equipment. The obtained papers and nanopapers were physical- and mechanically-characterized. The results showed a significant increase in density and a reduction of porosity in the samples during their transition from paper to nanopaper; besides, nanopapers were more transparent and smoother than normal papers. These physical changes where more evident with increasing amounts of NFC. Regarding mechanical properties, nanopapers with a 100 wt% content of NFC improved their strength and rigidity in 228 and 317 %, respectively, in comparison with normal papers. The evolution of strength and rigidity from paper to nanopaper was linear in relation to the amount of NFC, which means that the ultimate tensile strength was mainly dependant on nanofibril failure. [ABSTRACT FROM AUTHOR]

Microfibrillated cellulosic fibrous product was successfully obtained from Korean white pine ( Pinus koraiensis Sieb. et Zucc.) by using two alternative pretreatments (steam and ozone treatments) followed by disk milling (DM). The steam and ozone treatments were effective in extracting some of the hemicelluloses and degrading lignin, respectively, with both types of treatment resulting in the improvement of mechanical fibrillation as a result of loosening of the cell wall structure. The obtained products showed nanoscopic fibrous morphology even though hemicelluloses and lignin components remained. The specific surface area and filtration time were increased using the DM treatment after both treatments, and the values increased further with longer periods of DM. The paper sheets of the fibrillated products after both the alternative treatments had higher tensile properties at the same DM time scale than the sheets of the products obtained without treatment. Tensile strength was further increased by increasing sheet density showing the highest tensile strength and modulus of 125 MPa and 20 GPa, respectively. [ABSTRACT FROM AUTHOR]

Effect of silver nanoparticles on MMA/HEMA behavior in enhancing and restoring the lost chemical bonds of paper was estimated in the current study through the study of mechanical strengths (tensile and elongation), infrared spectrum and environmental microscopic examination. The results of tensile strength and elongation rate showed the effectiveness of nanoparticles in supporting paper properties under the influence of accelerated aging via the bond at 1630 cm−1 that is responsible for the bonds of silver ions and cellulose. Simultaneously, the micrographs showed that the type of fiber walls impacted the effectiveness of the copolymer where the completely pure cellulose cells absorbed the copolymer, while the presence of lignin reduced the absorption which helped create interface cross-links between fibers via the adsorbed copolymer on the surface. [ABSTRACT FROM AUTHOR]