Search

The effects of variable food supply on growth rate and feeding behaviour in two coexisting intertidal gastropods were examined through field and laboratory experiments involving mark and recapture procedures, growth experiments under controlled food supply and video observations of feeding. All cohorts of both Japeuthria species grew most in summer, with the highest growth rate being achieved by the youngest cohort of both sexes. In contrast, almost all cohorts (except the youngest one) showed zero to negative growth in winter. The growth rates of Japeuthria species clearly varied depending on feeding frequencies and the initial size of individuals. Females of both species had a significantly higher growth rate than males, though the difference became less marked with decreasing food supply. The total time spent on feeding and the length of the first feeding bout generally increased as the duration of the interval between meals was increased across treatments. From both the field growth experiment and the observations of feeding behaviour it is clear that J. ferrea had a higher frequency of feeding than J. cingulata in the field; 1- to 3-d intervals of feeding frequency in the former and 3- to 6-d intervals in the latter. Most notably, the two species showed a reversal in growth rates with changing conditions of food supply. When food was relatively abundant J. ferrea achieved better growth than J. cingulata, but J. cingulata grew better than J. ferrea under low food supply. In view of the fact that J. ferrea seems to be competitively superior to J. cingulata under normal levels, the present observation that J. cingulata can perform better than J. ferrea when food availability is low gives an important advantage to the latter in terms of its coexistence with the former.

The South American sun star Heliaster helianthus exhibits the unusual capability of foraging out of the water for the two mussel species on which it feeds. It schedules its foraging activities between five to four hours before high tide and ends at three to four and a half hours before high tide. Thus, foraging activity may last from 20 to 190 minutes and averages at 62 minutes. In addition, the sun-star does not vary its foraging behavior according to the extent of the mussel bed or the distance of the mussel bed from the water, and relies only upon the length of time it can stay out of the water without drying up from exposure to the sun.

Monitoring phycotoxin accumulation in marine products such as edible shellfish is a regulatory requirement in many countries. Therefore, a simple and rapid onsite quantification method is sought. Herein, we present a fluorescence polarization immunoassay (FPIA), a well-known one-step immunoassay, using a portable fluorescence polarization analyzer for domoic acid (DA), widely referred to as the primary toxin of amnesic shellfish poisoning (ASP). To establish FPIA for DA, the matrix effect of methanol, which is widely used to extract DA from shellfish, on FPIA was investigated. To validate this method, we performed a spike recovery test using oysters containing DA at a concentration equivalent to the regulatory limits of North America and the European Union (20 mg/kg). The recovery rate was found to be 79.4-114.7%, which is equivalent to that of the commercially available enzyme-linked immunosorbent assay (ELISA). We expect that this FPIA system will enable the quantitative onsite analysis of DA and significantly contribute to the safety of marine products., (© 2023. The Author(s).)

In this study, we developed an electrochemical sensor for ochratoxin A (OTA) by using an aptamer having a dithiol-based anchor, which exhibited higher stability on a gold electrode than a monothiol-based aptamer because of its two anchors. The sensor was also based on a signal-on scheme that produces a signal current resulting from structure-switching of the aptamer upon interaction with OTA. For simple fabrication of this sensor, the non-covalent interaction of methylene blue with the aptamer was also employed as an electrochemical indicator. In this study, the performance of the sensor, including the dissociation constant of the aptamer-OTA complex, was characterized. The proposed sensor exhibited high reproducibility and enough sensitivity to detect the minimum amount of OTA required for the analysis of real food samples with a limit of detection of 113 pM.

We report on the effects of fabrication methods, photolithography, wax printing, screen printing, and craft cutting, on selected properties of microfluidic paper-based analytical devices (μPADs): cost, fabrication precision, wicking rate, and analytical accuracy. Photolithography requires numerous fabrication steps, and an oxygen plasma treatment is necessary when using an aqueous solution. Although the boundary between the hydrophobic and hydrophilic areas in the μPAD is sharpest, the obtained K-scale intensity in measuring of protein concentrations is lower than those of the devices by other methods. Wax printing offers the simplest and fastest fabrication, although solution leakage measures should be taken to improve the wicking rate and to prevent cross-contamination. Screen printing also offers easy fabrication. The screen-printed μPAD has a good wicking performance and shows a high detection intensity. Craft cutting allows automated fabrication of many μPADs at once. The craft cut μPAD has the fastest wicking rate among the four μPADs due to bare cellulose fibers. We consider that the detection intensity of this μPAD can be raised by optimizing the evaporation rate.

Recently, we developed a label-free detection method based on optical diffraction, and implemented it in on our fabricated micro- and nanofluidic device. This detection method is simple and useful for detecting biomolecules, but the device fabrication consists of complicated processes. In this paper, we propose a simple method for fabricating the micro- and nanofluidic device; the fabrication combines laser interference lithography with conventional photolithography. The performance of a device fabricated by the proposed method is comparable to the performance of the device in our previous study.

In this study, we developed an integrated, low-cost microfluidic cell culture system that is easy to use. This system consists of a disposable polystyrene microchip, a polytetrafluoroethylene valve, an air bubble trap, and an indium tin oxide temperature controller. Valve pressure resistance was validated with a manometer to be 3 MPa. The trap protected against bubble contamination. The temperature controller enabled the culture of Macaca mulatta RF/6A 135 vascular endothelial cells, which are difficult to culture in glass microchips, without a CO2 incubator. We determined the optimal coating conditions for these cells and were able to achieve stable, confluent culture within 1 week. This practical system is suitable for low-cost screening and has potential applications as circulatory cell culture systems and research platforms in cell biology.

We report on the colorimetric oxidation of 3,3',5,5'-tetramethylbenzidine (TMB) by hydrogen peroxide using horseradish peroxidase on photolithography-fabricated (P-PAD) and wax-printed (W-PAD) paper-based analytical devices. Fabricating PADs via photolithography exposes the hydrophilic areas to polymers (photoresists) and solvents, not only reducing the hydrophilicity, but also affecting the TMB-H2O2 assay system with an unavoidable incomplete elimination of photoresist during fabrication. Detection signals are then observed in the presence of photoresist residues on the P-PAD, even at a blank HRP concentration.

This review summarizes two microfluidic-based protein crystallization methods, protein crystallization behavior in the microfluidic devices, and their applications for X-ray crystal structure analysis. Microfluidic devices provide many advantages for protein crystallography; they require small sample volumes, provide high-throughput screening, and allow control of the protein crystallization. A droplet-based protein crystallization method is a useful technique for high-throughput screening and the formation of a single crystal without any complicated device fabrication process. Well-based microfluidic platforms also enable effective protein crystallization. This review also summarizes the protein crystal growth behavior in microfluidic devices as, is known from viewpoints of theoretical and experimental approaches. Finally, we introduce applications of microfluidic devices for on-chip crystal structure analysis.

We demonstrated a rapid immunoassay for detection of cat cystatin C (cCys-C) which is an important marker for chronic kidney disease in cats, using immuno-pillar chips. The required amount of reagent solution is 200 times smaller than that for the conventional ELISA in the 96-well microplate (0.5 μL versus 100 μL). In addition, the total assay time in the proposed method is more than 12 times shorter than in the conventional method (20 min versus 240 min). The limit of detection in the new method of 3 ng mL -1 is comparable to that of the conventional method (1 ng mL -1 ) and it is in the clinically relevant range.

Development of polymeric microfluidic devices has played an important role in the recent, rapid progress of biomedical research. Here we report a fabrication method for micropillars on poly(methyl methacrylate) (PMMA) substrates for separation of microscale objects. The fabricated micropillars enable continuous separation of microparticles only by introducing fluids. The present method offers a new strategy to fabricate polymeric prototype devices for R&D work.

A compact and lightweight liquid chromatography system is presented with overall dimensions of 26 cm width × 18 cm length × 21 cm height and weight of 2 kg. This system comprises a battery-operated compact electroosmotic pump, a manual injector, a microfluidic chip device containing a packed column and an electrochemical detector, and a USB bus-powered potentiostat. The pumping system was designed for microfluidic-based reversed-phase liquid chromatography in which an electroosmotically generated water stream pushes the mobile phase via a diaphragm for the output. The flow rate ranged from 0 to 10 μL/min and had a high degree of precision. The pumping system operated continuously for over 24 h with dry batteries. The column formed in the microfluidic device was packed with 3-μm ODS particles with a length of 30 mm and a diameter of 0.8 mm. The results presented herein demonstrate the performance of the pumping system and the column using alkylphenols, catecholamine, catechin, and amino acids.

A microchip-based real-time polymerase chain reaction (PCR) device has been developed for the genetic tug-of-war (gTOW) method that provides quantitative data for research on biorobustness and systems biology. The device was constructed of a silicon glass chip, a temperature controlling Peltier element, and a microscope. A parallel real-time amplification process of target genes on the plasmids and the housekeeping genes in a model eukaryote Saccharomyces cerevisiae were detected simultaneously, and the copy number of the target genes were estimated. The device provides unique quantitative data that can be used to augment understanding of the system-level properties of living cells.

We developed a confocal microscopic method for a quantitative evaluation of the mixing performance of a three-dimensional microfluidic mixer. We fabricated a microfluidic baker's transformation (MBT) mixer as a three-dimensional passive-type mixer for the efficient mixing of solutions. Although the MBT mixer is one type of ideal mixers, it is hard to evaluate its mixing performance, since the MBT mixer is based on several cycles of complicated three-dimensional microchannel structures. We applied the method developed here to evaluate the mixing of water and a fluorescein isothiocyanate (FITC; diffusion coefficient, 4.9 × 10(-10) m(2) s(-1)) solution by the MBT mixer. This method enables us to capture vertical section images for the fluid distributions of FITC and water at different three-dimensional microchannel structures of the MBT device. These images are in good agreement with those of mixing images based on numerical simulations. The mixing ratio could be calculated by the fluorescence intensity at each pixel of the vertical section image; complete mixing is recognized by a mixing ratio of more than 90%. The mixing ratios are measured at different cycles of the MBT mixer by changing the flow rate; the mixing performance is evaluated by comparisons with the mixing ratio of the straight microchannel without the MBT mixer.

We have realized a cloned enzyme donor immunoassay (CEDIA) on a microchip in 96 s. CEDIA is a homogeneous immunoassay, based on the bacterial enzyme beta-galactosidase, which was genetically engineered into two inactive fragments: an enzyme donor and an enzyme acceptor. A model analyte was theophylline, and the detectable concentration range was from 0 to 40 microg mL(-1). Our CEDIA using a microfluidic device was very simple and rapid, unlike microchip-based heterogeneous immunoassays and CEDIA on a well-type microchip.

Poly(methylmethacrylate) (PMMA) microchip electrophoresis of sodium dodecyl sulfate-protein complexes (SDS-PC) using linear-poly(acrylamide) (L-PA) as a separation matrix was investigated. Prior to electrophoresis, channel walls of PMMA were modified with methylcellulose (MC) to prevent adsorption between channel walls and SDS-PC. Size-based protein separation (SBPS) was successfully performed using the MC-coated microchips with Ferguson plot-fittings. The entangled L-PA solution provided high resolution of peaks of SDS-PC when the concentration of L-PA was increased. Some investigations into the separation mechanism, such as the plot of the logarithm of mobility of each SDS-PC versus the logarithm of the molecular weight of the complex exhibiting linear behavior, indicated that the separation mechanism was dependent on mass discrimination, in accordance with Ogston model.

We have developed a new method for a fast and precise analysis of circle-to-circle amplification (C2CA) product for specific gene detection by microchip electrophoresis. In this method, we have added a new enzymatic step to the C2CA reaction, which could be carried out isothermally at 37 degrees C. Compared to the original single-stranded DNA, the double-stranded DNA that is produced by this enzymatic reaction is more reliable for analysis by microchip electrophoresis. C2CA product was detected within 55 s with high reproducibility by this method which was successfully applied to the detection of 10-ng genomic DNA of the pathogenic bacteria Vibrio. cholerae within 110 s. Purification was found to be an indispensable step for the analysis of the C2CA product of genomic DNA samples.

We have developed a fluorescence resonance energy transfer (FRET) probe based on the conjugation of a quantum dot (QD) with dye (YOYO-3) intercalated DNA. The FRET-inducing electrostatic coupling of DNA and the QD made structural changes to the QD-DNA conjugates, which significantly prevented an enzymatic reaction between the DNA and a conventional restriction endonuclease (EcoRI).

The emerging nanomaterial, quantum dots or QDs, offers numerous potential applications in the biological area. As cell labeling probes, QDs become now an alternative of existing organic fluorescent dyes and fluorescent proteins. In this short review, we cover typical and successful applications of QDs as fluorescent probes in cell labeling and genomic diagnosis. As a future important application, biomolecular detection at a single molecule level utilizing QDs is also discussed.

A detection and fixation method of single and multiple gold nanoparticles on the wall of a microfluidic channel is demonstrated. A thermal lens microscope (TLM) with continuous-wave excitation (wavelength, 532 nm) and probe (wavelength, 670 nm) laser beams was used to realize the sensitive detection of heat generated by light absorption of individual gold nanoparticles (50 nm in diameter); fixation of the individual nanoparticles was realized simultaneously. The fixation mechanism was investigated and attributed to an absorption-based optical force. In addition to single nanoparticle detection, multiple-nanoparticle detection and fixation was demonstrated. An acceleration of fixation was observed when the number of fixed particles was increased. TLM is expected to be a powerful tool for both the quantitative detection and precise fixation of individual nanoparticles.

We developed a fabrication method and a liquid filling method for a nano chemical reactor that used Y-shaped nanochannels specially designed for mixing and reacting. In order to reduce the pressure loss and to utilize the characteristics of the nanochannel, inlet microchannels were fabricated just beside the nanochannels. We investigated an initial liquid filling method into the nanochannels that ensured there were no air bubbles that could cause a flow stack due to the capillary pressure. In our method, the micro- and nanochannels were filled with carbon dioxide and any remaining air during the initial liquid introduction was dissolved utilizing the high solubility of carbon dioxide. We propose that chemical reactions in nanospaces can be realized by utilizing these fabrication and liquid introduction techniques.

This paper presents a capillary-to-microchip connection, which can be used as an interface for coupling capillary electrophoresis (CE) with a thermal lens microscope (TLM). It is difficult to directly apply TLM to samples in a capillary with a curved surface, and such an interface chip at the end of a CE separation column is needed for reliable TLM measurements. The dependence of the TLM signal intensity on the TLM detection point in the interface chip and the dependence of the theoretical plate number of CE separation on the channel dimensions of the interface chip were investigated and optimized with a mixture of 4-dimethylaminoazobenze-4'-sulfonyl (DABSYL)-derivatized amino acids (glycine, alanine, methionine, and proline) as a model sample. By using an optimized interface chip, theoretical plate numbers of DABSYL-glycine, -methionine, -alanine, and -proline were obtained to be 104000, 95000, 104000, and 95000, respectively.

This review focuses on the integration of chemical and biochemical analysis systems into glass microchips for general use. By combining multiphase laminar flow driven by pressure and micro unit operations, such as mixing, reaction, extraction and separation, continuous-flow chemical processing systems can be realized in the microchip format, while the application of electrophoresis-based chip technology is limited. The performances of several analysis systems were greatly improved by microchip integration because of some characteristics of microspace, i.e., a large specific interface area, a short molecular diffusion time, a small heat capacity and so on. By applying these concepts, several different analysis systems, i.e., wet analysis of cobalt ion, multi-ion sensor, immunoassay, and cellular analysis, were successfully integrated on a microchip. These microchip technologies are promising for meeting the future demands of high-throughput chemical processing.

We utilized microchip technology and found that the multilayer flow of liquids can be formed in microchannels. Liquid/liquid interfaces were formed parallel to the side wall of the microchannels, because the surface tension and friction force are stronger than the force of gravity. A water/ethylacetate/water interface was formed in a 70-microm-wide and 30-microm-deep channel. The interface was observed to be quite stable and to be maintained for a distance of more than 18 cm. As an example of a multilayer flow application, we demonstrated the liquid/liquid extraction of Co-dimethylaminophenol complex in a microchannel. The solvent-extraction process of the complex into m-xylene in the multilayer flow was found to reach equilibrium in 4 s, while it took 60 s in a simple two-phase extraction.