Search

Introduction: The utilization of metal shields in intensity-modulated brachytherapy (IMBT) enables the modulation of the dose, resulting in improved conformance to the tumor while simultaneously reducing the doses to organs at risk (OARs). Utilizing higher-energy sources like 60 Co in IMBT for cervical and vaginal cancers has consistently posed challenges. This study evaluates the dosimetric aspects of modified applicators designed for IMBT using 60 Co and 192 Ir sources., Materials and Methods: GATE, a Geant4-based simulation code, was utilized to model and simulate four distinct applicators. The clinical applicators were redesigned to place the structure of the source tube and the shield while keeping the general characteristics unchanged. These shields were evaluated by calculating transmission factors (TFs) and the dose homogeneities were also determined., Result: Transmission factors for the IMBT technique in redesigned intrauterine applicators and tungsten shields for iridium and cobalt sources were at least 12.8 and 65.4%, and these values were obtained for the intravaginal applicator at 0.2 and 7.0%, respectively. The dose homogeneities for all combinations of radionuclide-shield were within a 15% range of the non-IMBT applicators., Conclusion: This study has quantitatively evaluated the dosimetric effect of tungsten shields in the IMBT technique for cervical and vaginal cancer using cobalt sources. 192 Ir compared to 60 Co resulted in higher effectiveness for the designed intrauterine and intravaginal shields. while implementing tungsten shields in the redesigned applicators against the 60 Co source may not offer complete protection, it does show promising results in reducing the dose to organs at risk., (© 2024. The Author(s).)

Purpose Objective(s): Manual contouring of the prostate region in planning computed tomography (CT) images is a challenging task due to factors such as low contrast in soft tissues, inter- and intra-observer variability, and variations in organ size and shape. Consequently, the use of automated contouring methods can offer significant advantages. In this study, we aimed to investigate automated male pelvic multi-organ contouring in multi-center planning CT images using a hybrid convolutional neural network-vision transformer (CNN-ViT) that combines convolutional and ViT techniques., Materials/methods: We used retrospective data from 104 localized prostate cancer patients, with delineations of the clinical target volume (CTV) and critical organs at risk (OAR) for external beam radiotherapy. We introduced a novel attention-based fusion module that merges detailed features extracted through convolution with the global features obtained through the ViT., Results: The average dice similarity coefficients (DSCs) achieved by VGG16-UNet-ViT for the prostate, bladder, rectum, right femoral head (RFH), and left femoral head (LFH) were 91.75%, 95.32%, 87.00%, 96.30%, and 96.34%, respectively. Experiments conducted on multi-center planning CT images indicate that combining the ViT structure with the CNN network resulted in superior performance for all organs compared to pure CNN and transformer architectures. Furthermore, the proposed method achieves more precise contours compared to state-of-the-art techniques., Conclusion: Results demonstrate that integrating ViT into CNN architectures significantly improves segmentation performance. These results show promise as a reliable and efficient tool to facilitate prostate radiotherapy treatment planning., (© 2024. The Author(s).)

Analyzing municipal wastewater for the presence of Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2) helps to evaluate the efficacy of treatment systems in mitigating virus-related health risks. This research investigates wastewater treatment plants' (WWTPs) performance in the reduction of SARS-CoV-2 from municipal wastewater in Tehran, Iran. SARS-CoV-2 RNA was measured within sewers, at the inlets, and after the primary and secondary treatment stages of three main WWTPs. Within sewers, the average virus titer stood at 58,600 gc/L, while at WWTP inlets, it measured 38,136 gc/L. A substantial 67% reduction in virus titer was observed at the inlets, accompanied by a 2-log reduction post-primary treatment. Remarkably, the biological treatment process resulted in complete virus elimination across all plants. Additionally, a notable positive correlation (r > 0.8) was observed between temperature and virus titer in wastewater. Using wastewater-based epidemiology (WBE) technique and the estimated SARS-CoV-2 RNA shedding rates, the infection prevalence among populations served by WWTPs found to be between 0.128% to 0.577%. In conclusion, this research not only advances our understanding of SARS-CoV-2 dynamics within wastewater treatment systems but also provides practical insights for enhancing treatment efficiency and implementing the feasibility of WBE strategies in Tehran. These implications contribute to the broader efforts to protect public health and mitigate the impact of future viral outbreaks., Competing Interests: Conflict of interestThe authors declare that they have no competing interests or any personal relationships that could have appeared to influence the content of this paper., (© The Author(s), under exclusive licence to Tehran University of Medical Sciences 2024. Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.)

Groundwater is one of the major sources of exploitation in arid and semiarid regions. Spatial and temporal quality distribution is an important factor in groundwater management. Thus for protecting groundwater quality, data production on spatial and temporal distribution is essential. The present study has applied multiple linear regression (MLR) techniques to predict the fitness of groundwater quality in Kermanshah province, west of Iran. The parameters examined were Total dissolved solids (TDS), Total hardness (TH), Sodium adsorption ratio (SAR). the quality variables were modelled by MLR. Finally, the performance of the models was assessed using the coefficient of determination (R 2 ). The relationship between parameters by MLR showed that TDS and water quality parameters in semi-deep wells and aquifers had a strong positive correlation (r = 0.94, r = 0.98) and there was a strong positive significant correlation between SAR and water quality parameters in deep wells and aquifers (r = 0.98, r = 0.99). Also, TH and water quality parameters in all water sources had a strong positive correlation (r = 1). The MLR model could serve as an alternative and cost-effective tool for groundwater quality prediction where there is limitation in laboratory facilities, trained expertise or time. Consequently, the usefulness of these linear regression equations in predicting the groundwater quality is an approach, which can be applied in any other locations., Competing Interests: Conflict of interestThe authors declare that They have no conflict of interest., (© The Author(s), under exclusive licence to Tehran University of Medical Sciences 2022, Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.)

Purpose: Bisphenol A (BPA), as endocrine-disrupting compound (EDC), is extensively used as an important chemical in the synthesis of polycarbonate polymers and epoxy resins. BPA absorption into the body can result in the development of metabolic disorders such as low sex-specific neurodevelopment, immune toxicity, neurotoxicity and interference of cellular pathway. Therefore, the presence of BPA in the body and the environment can create hazards that must reach standards before being discharged into the environment., Methods: In this study, bismuth ferric nanomagnetic (BFO NMPs) were successfully synthesized via sol-gel method and developed as photocatalysts for BPA removal under visible light irradiation. FE-SEM, TEM, PL, XRD, UV-Vis DRS, VSM, EDX, and FTIR were used to characterize the BFO NMPs., Results: RSM model (R 2  = 0.9745) showed a good correlation between experimental and predicted removal efficiency of BPA. The investigation of four independent variables indicated that pH had the most significant positive effect on the degradation of BPA. Under optimal conditions (pH = 4.042, catalyst dose = 7.617 mg, contact time = 122.742 min and BPA concentration = 15.065 mg/L), maximum degradation was calculated to be 98.7%. After five recycles, the removal of BPA remained >82%, which indicated the proper ability to reuse the catalyst., Conclusion: In conclusion, it can be stated like BPA, the prepared BFO NMPs is a promising photocatalyst for practical application in organic pollutant decomposition., Competing Interests: Conflict of interestAll authors certify that they have no affiliations with or involvement in any organization or entity with any financial interest or non-financial interest in the subject matter or materials discussed in this manuscript., (© The Author(s), under exclusive licence to Tehran University of Medical Sciences 2022.)

Background: ZAK protein is a member of the MLK family proteins defined as mediators in the cell cycle. A survey of ZAK gene expression in gastric antral epithelial cells (GAECs) of gastritis and gastric adenocarcinoma patients with Helicobacter pylori genotypes infection can elucidate carcinogenesis of H. pylori genotypes., Methods: In a case-control study, ZAK gene expression was evaluated in GAECs biopsy samples of gastritis and gastric adenocarcinoma patients with (n 23, 21) and without H. pylori infection (n 27, 32), respectively. Total RNA was extracted from each gastric antral biopsy samples and cDNA synthesized by using Takara kits. H. pylori virulence genes֝ cDNA were detected by traditional PCR and specific primers. The ZAK gene expression was measured using the relative Real-Time RT PCR., Results: The prevalence of gastric adenocarcinoma was the highest in man and 61-85 aged groups (p < .05). There was no significant correlation between the prevalence of H. pylori infection and patients' demographic groups. This study showed that ZAK gene overexpression gradually increases with increasing age and tumor grade among gastric adenocarcinoma patients. The gastric antral biopsy samples with H. pylori vacA s1m2 genotype infection showed a weak correlation with ZAK gene overexpression (p < .1)., Conclusion: ZAK gene expression was higher in GAECs of gastritis cancer than in gastric adenocarcinoma, indicating the protective effect of ZAK against gastric cancer (p < .005). Reducing ZAK gene expression shows the negative correlations with H. pylori infection and gastric adenocarcinoma., (© 2021. Springer Science+Business Media, LLC, part of Springer Nature.)

Diazinon is a widely used pesticide that can be effectively degraded in aqueous solutions via photocatalytic oxidation. This quantitative systematic review was conducted to shed light on the various aspects of photocatalytic diazinon removal based on evidence. A systematic search was performed in Scopus, PubMed, Web of Science, Embase, and Ovid databases with keywords including diazinon, photocatalysis, and their equivalents. The search was limited to original articles in English published between January 1, 2010, and March 25, 2021. The results were expressed by descriptive statistics including mean, SD, median, and percentiles, among others. The initial electronic and manual search retrieved 777 articles, among which 41 studies comprising 49 trials were qualified for data synthesis. The reported diazinon degradation rate ranged from 2 to 100%, with a mean ± SD of 59.17 ± 28.03%. Besides, ZnO/UV, WO 3 /UV, TiO 2 /UV, and TiO 2 /Vis, in sequence, were the most widely used processes with the highest efficacies. Solution pH in the range of 5-8, catalyst dose below 600 mg/L, diazinon initial concentration below 40 mg/L, and contact time of 20-140 min could be the optimum conditions. Diazinon degradation obeyed the first-order kinetic model with k obs between 0.0042 and 1.86 min -1 and consumed energy of 38.93-350.36 kWh/m 3 . Diazoxon and IMP were the most detected by-products of diazinon degradation although bioassay data were scarce. Based on the results, photocatalytic processes are very efficient in removing diazinon from aqueous solutions although more elaborate studies are needed to assess the mineralization rate and effluent toxicity., (© 2022. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Water quality is one of the most important indices for public health especially for drinking water consumptions. This study was conducted to survey the presence of heavy metals in drinking water resources of Iran using a systematic review and meta-analysis. The literature search was conducted in data bases of PubMed, Web of Science, EMBASE, Scopus, Google Scholar, and some Persian databases up to 31 July 2018. Of all the articles reviewed (1151 articles), 61 papers were eligible for systematic review. Results indicated variable heterogeneity between studies for different pollutants (I 2 between 0 and 100). A subgroup analysis was performed for three different types of water resources such as drinking water, groundwater, and surface water to find the possible source of the heterogeneity. The pooled mean concentration level of iron was the highest at 255.8 (95% CI = 79.48-432.13 μg/l) and vanadium the lowest at 3.21 (95% CI = 1.45-4.98 μg/l). The sequence of metal concentration (μg/l) in descending order is as follows: Fe (255.8) > B (159.81) > Al (158.5) > Zn (130.73) > As (85.85) > Mn (51.61) > Cu (47.98) > Se (42.68) > Pb (37.22) > Co (22.76) > Mo (18.92) > Ni (16.79) > Cr (13.47) > Hg (4.49) > Cd (4.19) > V (3.21). The mean pooled concentration level of Al, As, Se, Pb, and Cd was higher than the WHO guideline and Iran Standard, and the rest of the metals had lower mean pooled concentration level. Pb and Cd were the common heavy metals that existed in all subgroups. As a recommendation, the relationship assessment of water parameters and heavy metals could be addressed in future studies of Iran's water resources.

This study aimed to identifying the presence of SARS-CoV-2 RNA in raw and treated wastewater during the COVID-19 outbreak in Tehran, Qom and Anzali cities (Iran). From three wastewater treatment plants (WWTPs), 28 treated and untreated wastewater composite samples were collected from April 4 to May 2, 2020. In this study, polyethylene glycol 6000 (PEG 6000) was used through one-step real-time quantitative reverse transcriptase-polymerase chain reaction (qRT-PCR) for identification of RNA viruses. SARS-CoV-2 RNA was elicited from wastewater composite samples in all inlet samples taken from the three above mentioned cities. The results of outlet samples were as follows: 1) Results from Qom and East Anzali outlets showed no trace of SARS-CoV-2 RNA despite the difference in treatment disinfection method used (chlorine vs. ultraviolet (UV) disinfection). 2. In Tehran, SARS-CoV-2 RNA was not detected in any of the outlet samples taken from the modules disinfected by UV. Out of the four samples taken from the modules disinfected by chlorine, two were positive for the SARS-CoV-2 RNA which could have been caused by deficiencies in operation and maintenance. It can be concluded that meeting the standards of operation and maintenance (O&M) in WWTPs can considerably ensure that wastewater does not act as one of the roots of transmission for the disease., Competing Interests: Conflict of interestThe authors declare that they have no conflict of interest., (© Springer Nature Switzerland AG 2021.)

In Ahwaz, a city in west southern Iran, the majority of households are using Point of Use (PoU) water treatment units. The heterotrophic plate count (HPC) bacteria were isolated from these units while they were mounted on water distribution system in order to determine the variations in HPC and diversity of the bacterial population using polymerase chain reaction (PCR). Results showed that bacterial population regrowth in PoU units could increase HPC exceeding the limit of the 500 CFU/mL in outlet water. In around 70% of the input water samples, the HPC was less than 500 CFU/ml with a mean of 226.7 (CI 95%: 28.1-425.3). HPC in output treated water samples had an increasing trend from the start of the unit operation with a mean of 2416.4 (CI 95%: 1074.9-3757.9). Out of 49 detected bacterial strains, 20 strains were Gram-negative and 29 Gram-positive. Bacillus was the most frequent genes detected in inlet and outlet water samples. Most of the identified bacterial strains were opportunistic pathogens potentially dangerous for immunocompromised population. HPC population in PoU units significantly can be increased during a one-month period of operation, so replacement of the filters must be done regularly., Competing Interests: Conflict of interestThe authors declare that they have no conflict of interests., (© Springer Nature Switzerland AG 2021.)

This study surveys the possibility to optimally produce active chlorine from synthetic saline solutions using electrolysis by Response Surface Methodology (RSM). Various operating parameters, such as sodium chloride concentration, electrical potential and electrolysis time were evaluated. Central composite design (CCD) was applied to determine the optimal experimental factors for chlorine production. The experimental design, statistical analysis of the data and optimization were performed using R 3.5.3 software. The results showed that the optimum value of electrical efficiency (42 mg Cl 2 /kj) was obtained at the electrical voltage of 15.73 V during 15.63 min in the presence of 63.42 g/l of sodium chloride. The optimum point for current efficiency was 38.40%, which was obtained at the electrical voltage of 10.76 V during 6.70 min in the presence of 34.65 g/l of sodium chloride. Moreover, generated active chlorine was optimized based on energy consumption, which was 77 mg/l for the energy consumption of 0.2 kWh/l at a current density of 2000 mA/cm 2 . The electrochemical production of the chlorine gas from saline or brine water can be extensively used for water disinfection., Competing Interests: Conflict of interestThe authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© Springer Nature Switzerland AG 2020.)

Purpose: To advance knowledge about childhood neurodevelopmental disorders and study their environmental determinants, we conducted a study in Tehran, Iran to assess the feasibility of prospective birth cohort study., Methods: We evaluated participation of pregnant women, feasibility of sampling biological material, and health care services availability in Tehran in four steps: (1) first trimester of pregnancy; (2) third trimester of pregnancy; (3) at delivery; and (4) two to three months after delivery. We collected related data through questionnaires, also various biological samples were obtained from mothers (blood, urine, milk and nails-hands and feet) and newborns (umbilical cord blood, meconium, and urine samples) from February 2016 to October 2017., Results: overall 838 eligible pregnant women were approached. The participation rate was 206(25%) in our study and about 185(90%) of subjects were recruited in hospitals. Out of 206 participants in the first trimester, blood, urine, hand nail, and foot nail samples were collected from 206(100%),193(93%), 205(99%), and 205(99%), respectively. These values dropped to 65(54%), 83(69%), 84(70%), and 84(70%) for the remaining participants 120(58%) in the third trimester, respectively. Also, we gathered milk samples from 125(60%) of mothers at two to three months after delivery., Conclusion: Our findings suggest that hospitals were better places for recruitment of subjects in a birth cohort in Tehran. We further concluded that birth cohort study recruitment can be improved by choosing appropriate gestational ages. Obtaining the newborn's urine, meconium, and umbilical cord blood were challenging procedures and require good collaboration between hospital staff and researchers., (© Springer Nature Switzerland AG 2020.)

Purpose: Open flames of gas and charcoal can induce polycyclic aromatic hydrocarbons (PAHs) in cooked meat. The current study aimed to compare the effect of gas and charcoal open flames on the induction of PAHs in cooked meat using a meta-analysis approach., Methods: A systematic review of the literature was conducted electronically based on the PRISMA guidelines. Experimental studies comparing the PAHs content of cooked meat over open flames of gas and charcoal were searched using the appropriate keywords until June 2018., Results: Of 1137 papers retrieved, 7 with a total sample size of 474 meat samples were used in the meta-analysis. The mean difference (MD) between the gas and charcoal cooking methods in the induction of each PAH was 2.053 μg/Kg. (95%CI: 1.022-3.085 μg/Kg; P  < 0.001). The subgroup analysis of 17 trials indicated the difference between the two cooking methods increases when red meat rather than white meat is cooked (MD in red meat: 3.499 μg/Kg; 95%CI: 2.030-4.967; P  < 0.0001 vs. MD in white meat: 3.319 μg/Kg; 95% CI: 1.689-4.950; P < 0.0001). Interestingly, studies that analyzed meat samples for fewer PAHs (cut-off ≤7) found a much wider difference between gas and charcoal-cooked meat (MD: 5.106 μg/Kg; (95% CI: 2.162-8.049; P  < 0.001 in studies with ≤7 PAHs vs. MD: 1.447 μg/Kg; 95% CI: 0.628-2.266; P < 0.001 in studies with >7 PAHs)., Conclusions: It is necessary to avoid open flames of charcoal as the heat source or change the geometry of charcoal-fired cookstoves to prevent fat dripping on the fire and thus, excessive PAHs induction., Competing Interests: Conflict of interestsNone declared., (© Springer Nature Switzerland AG 2020.)

Ketoconazole is an imidazole fungicide which is commonly used as pharmaceutical and healthcare products. Residual amount of this compound can cause adverse ecological health problems. The present study investigated ketoconazole photocatalytic degradation using Ag 3 PO 4 /graphene oxide (GO). Ag 3 PO 4 /GO and Ag 3 PO 4 as visible light-driven photocatalysts was synthesized using the in situ growth method. Degradation of ketoconazole at the concentration of 1-20 mg/L in aqueous solutions was optimized in the presence of Ag 3 PO 4 /GO nanocomposite with the dosage of 0.5-2 g/L, contact time of 15-20 min, and pH of 5-9 using response surface methodology. A second-order model was selected as the best fitted model with R 2 value and lack of fit as 0.935 and 0.06, respectively. Under the optimized conditions, the Ag 3 PO 4 /GO catalyst achieved a photocatalytic efficiency of 96.53% after 93.34 min. The photocatalytic activity, reaction kinetics, and stability were also investigated. The results indicated that the Ag 3 PO 4 /GO nanocomposite exhibited higher photocatalytic activity for ketoconazole degradation, which was 2.4 times that of pure Ag 3 PO 4 . Finally, a direct Z-scheme mechanism was found to be responsible for enhanced photocatalytic activity in the Ag 3 PO 4 /GO nanocomposite. The high photocatalytic activity, acceptable reusability, and good aqueous stability make the Ag 3 PO 4 /GO nanocomposite a promising nanophotocatalyst for photocatalytic degradation of azoles contaminants.

Background: The most common method of combating insects in low-income communities and developing countries, is the use of insecticides. The use of organophosphate insecticides is increasing due to their low prices and availability on the market. Chlorpyrifos is a medium-risk insecticide for human. The widespread use of organophosphorus insecticides, especially chlorpyrifos, in residential homes has undoubtedly created many health concerns. Babies have a high sensitivity to pesticides and environmental contaminants because of their evolutionary status. On the other hand, the main source of infants' exposure who are breast-fed exclusively to environmental pollutants is through breast milk and oral contact with objects that are covered with dust and particles., Methods: In this cross-sectional study, the concentration of chlorpyrifos in breast milk and its metabolite in urine samples of mothers and their under six months infants, feeding exclusively by breast milk in north of Iran have been investigated. The demographic data was collected through interviewing with selected mothers and completion of prepared data collecting forms. The data were statistically analyzed to investigate the relationships between exposure of mothers and their infants to chlorpyrifos., Results: The mean concentration of chlorpyrifos and its metabolite in mothers' urine and milk samples and infant's urines were 1.3 ± 0.6, 2.1 ± 1.4 and 1.4 ± 0.7 μg/L, respectively. Also, the mean concentration of chlorpyrifos in the dust on the house floors was73.4 ± 49 ng/g. There are good correlations between the mean values of chlorpyrifos concentrations and its metabolite in mother's milk and urine (r = 0.872, p  = 0.001), and the mother's milk and infant's urine (r = 0.722, p = 0.001). Also, there was a significant correlation between the concentration of chlorpyrifos in floor dust and its metabolites in the infant's urine (r = 0.554, p  = 0.001)., Conclusion: Our study suggests that the infants are the recipient of concentrated forms of chlorpyrifos residues through breast milk and house dust and it is quite well known that OP pesticides are toxic and have different kinds of adverse health effects. However, further research needs to be done to determine what these chemicals are doing to our children., Competing Interests: Conflict of interestThe authors declare that there is no conflict of interest., (© Springer Nature Switzerland AG 2019.)

Trihalomethanes (THMs) have been proven to be potentially genotoxic and mutagenic for human. The aim of this study was to characterize the THMs spatiotemporal distribution and its carcinogenic risk potential in Ardabil water distribution system. Water samples were collected over consecutive months from twenty-six points in the city of Ardabil from April 2016 to March 2017. The potential carcinogenic risk assessment of THMs was evaluated quantitatively with uncertainty assessment based on Monte-Carlo simulation technique. The results showed that the mean concentrations of bromodichloromethane, Chloroform, dibromochloromethane and Bromoform in water consumed by residents were 101.97 ± 58.51, 85.18 ± 47.79, 51.67 ± 29.57 and 11.89 ± 6.64 μg/L, respectively, during the sampling period. According to the result of this study, the concentrations of THMs were higher in summer in comparison with other seasons. The mean values of lifetime cancer risks for residents through ingestion, inhalation and dermal contact are 2.85×10-4, 6.46×10-7, and 1.26×10-7, respectively. The lifetime cancer risks for residents through ingestion was found to be 285 times more than the minimum or negligible level set by US.EPA (1.0×10-6) and for dermal contact and inhalation lower than the minimum or negligible level set by US.EPA. The results of the present research may contribute to inform the decision makers of drinking water supply system about the role of water quality in the health of consumers., (© Springer Nature Switzerland AG 2019.)

The aim of this systematic review study was to investigate the causal relationship between environmental factors and gastric cancer (GC) in Iran. In a narrow definition, the environment includes water, soil, air, and food. This definition was the main criterion for the inclusion of articles in this study. In addition, exposure to radiation and geographical conditions were considered as less investigated environmental factors in the literatures. International (PubMed, Web of Science, ScienceDirect, Scopus, and Cochran) and national (Scientific Information Database) databases were searched for articles on GC and environmental risk factors in Iran. Twenty-six articles were found to meet the inclusion criteria after title, abstract, and full text review. Risk factors identified for GC include consumption of red meat; high fat, fried, and salted meat; smoked, salted, and fried foods; some dairy products; roasted and fried seeds; strong and hot tea; and un-piped and unchlorinated drinking water, as well as exposure to radiation, loess sediment, soft and grassy soil, soil containing low concentration of molybdenum, and proximity to volcanos. Fresh fruits and vegetable, fresh fish, and honey consumption were recognized as protective agents. Given the risk factors identified, strategies to prevent GC would be educating people to choose a healthy diet and to cook and store food properly, providing access to safe drinking water, taking into account topographical and geographical conditions in choosing a right location to build residential areas, and regulating the use of radiation-emitting devices.

Background: Gastric cancer (GC) is the first leading cause of cancer-related deaths in Iran. GC is a multifactorial disease and is caused by the interaction of genetic and environmental factors. The aim of this study was to assess the exposure and risk of nitrate intake through fruits and vegetables (F&V) in high-risk area (HRA) and low-risk area (LRA) of GC in Iran., Methods: Twenty nine species of F&V were examined for nitrate by reverse-phase HPLC (RP-HPLC) method. Food frequency questionnaire (FFQ) data of 2000 adults participating in Persian cohort were applied to determine consumption patterns of F&V in those areas. A point-estimate daily intake was applied to compare two areas in terms of nitrate intake. Monte-Carlo simulation technique was applied to estimate chronic daily intake (CDI) of nitrate., Results: The results showed that point-estimate daily intake of nitrate for subjects participated in the study was 2.02 ± 1.02 mg kg -1  day -1 in HRA and 1.98 ± 1.05 mg kg -1  day -1 in LRA. 6.53% of the participants in the HRA, and 5.9% of the participants in the LRA had an unacceptable point-estimate daily intake compared with an acceptable limit of 3.7 mg kg -1  day -1 established by FAO/WHO. CDI of nitrate in HRA was 1.94 ± 0.95 mg kg -1  day -1 and in the LRA was 1.93 ± 1.06 mg kg -1  day -1 ., Conclusion: The results showed that there is no difference between HRA and LRA in terms of nitrate intake through F&V., Competing Interests: Conflict of interestThe authors declare no conflict of interest.

Background: Application of the point-of-use water treatment (POU-WT) systems has consistently increased during the last decade in Iran. In this study, the qualitative performances of reverse osmosis-based POU devices in selected cities of Iran were investigated., Methods: This applied- descriptive study was conducted in three cities of Tehran, Rasht, and Ahvaz in 2016 (selected based on the level of POU devices sale index in three phases). After choosing the most popular five brands of six stages POU devices, 360 water sampling zones and POU consumer households of the selected cities were measured. Also, the awareness of the consumers about POU-WT systems selection and performance was investigated through a designed questionnaire., Results: The qualitative parameters in the three cities were acceptable ( p  < 0.05) for tap water (except for EC in Ahvaz), the output water were as follows: pH = 6.05-7.5, EC = 49.8-58.2 μs/cm, TOC = 0.01-0.23 mg/L and Nitrate = 0.52-4.5 mg/LNO 3 (lower or within the range of regulatory limits), Total Hardness = 33-41.5 mg/L and Fluoride = 0.01-0.23 mg/L (which were lower than the admissible limit, with p  < 0.05), HPC values were in the range of 543-676 CFU/mL, which exceeded the regulatory level. Results of ANOVA analysis showed significant differences between the selected cities. The results of the questionnaire survey showed that the dissatisfaction of tap water quality and health-related concerns were the two main reasons for household POU-WT systems; awareness levels of 64% of these households about the performances of their POU systems were weak. Also, social media were mostly used by POU-WT users for brand selected., Conclusion: Based on the results of the tap-water quality application of POU-WT systems are not recommended in Tehran and Rasht, and regarding the outputs of these systems, side effects of softened water, lack of Fluoride and a remarkable increase of the number of bacteria should be considered. In Ahvaz, application of POU-WT systems can decrease the health-related problems and it is necessary to increase the access to read POU-WT efficiency information for the consumers., Competing Interests: Compliance with ethical standardsThe authors declare that there are no conflicts of interests.

Background: Antibiotic residues are being constantly identified in environmental waters at low concentration. Growing concern has been expressed over the adverse environmental and human health effects even at low concentration. Hence, it is crucial to develop a multi-residues analytical method for antibiotics to generate a considerable dataset which are necessary in the assessment of aquatic toxicity of environmental waters for aquatic organisms and human health. This work aimed to develop a reliable and sensitive multi-residue method based on high performance liquid chromatography coupled with quadrupole-linear ion trap tandem mass spectrometry (HPLC-MS-MS). The method was optimized and validated for simultaneous determination of four classes of antibiotics including, β-lactam, macrolide, fluoroquinolone and nitro-imidazole in treated, ground and surface water matrices., Methods: In order to optimize the solid phase extraction process, main parameters influencing the extraction process including, pH, the volume of elution solvent and the amount of Na 4 EDTA were evaluated. The optimization of extraction process was carried out by response surface methodology using central composite design. Analysis of variance was performed for nine target antibiotics using response surface methodology., Results: The extraction recoveries were found to be sensitive to the independent variables of pH, the volume of elution solvent and the amount of Na 4 EDTA. The extraction process was pH-dependent and pH was a significant model term in the extraction process of all target antibiotics. Method validation was performed in optimum operation conditions in which the recoveries were obtained in the range of 50-117% for seven antibiotics in spiked treated and ground water samples and for six antibiotics in spiked river water samples. Method validation parameters in terms of method detection limit were obtained in the range of 1-10 ng/L in treated water, 0.8-10 ng/L in the ground water and 0.8-25 ng/L in river water, linearity varied from 0.95 to 0.99 and repeatability in term of relative standard deviation values was achieved less than 10% with the exception for metronidazole and ceftriaxone. The developed method was applied to the analysis of target antibiotics in treated, ground and surface water samples., Conclusions: Target antibiotics were analyzed in different water matrices including treated, ground and river water. Seven out of nine antibiotics were detected in Kan River and Firozabad Ditch water samples, although none of them were detected in treated water and ground water samples.

Background: Polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDFs) are highly toxic persistent organic pollutants (POPs), which can cause various health outcomes, such as cancer. As a part of the National and Sub-national Burden of Disease Study (NASBOD), we aimed to estimate dioxins and furans national emissions, identify their main sources, estimate daily intake doses, and assess their trend from 1990-2010 in Iran., Methods: The Toolkit for Identification and Quantification of Releases of Dioxins, Furans and Other Unintentional POPs, which is developed by the United Nations Environment Programme (UNEP 2013), was used to estimate the emissions of PCDD/PCDFs from several sources into the air, water, land, residue, and other products. The daily intake doses were estimated using a linear regression of estimated emissions by UNEP Toolkit and average intake doses in other countries. Finally, the trend of PCDD/PCDFs emissions and daily intake doses were explored from 1990-2010., Results: The total emissions were estimated as 960 g Toxic Equivalents (g TEQ) for 1990 and 1957 g TEQ for 2010 (18.2 and 26.8 g TEQ per million capita, respectively). The estimations suggest that albeit contribution of open burning to PCDD/PCDFs emissions has been declining from 1990 to 2010, it remained the major source of emissions in Iran contributing to about 45.8% out of total emissions in 1990 to 35.7% in 2010. We further found that PCDD/PCDFs are mostly emitted into the ambient air, followed by residue, land, products, and water. The daily intake doses were estimated to be 3.1 and 5.4 pg TEQ/kg bw/day for 1990 and 2010, respectively. We estimated an increasing trend for PCDD/PCDFs emissions and intake doses in Iran from 1990-2010., Conclusions: The high levels of emissions, intake doses, and their increasing trend in Iran may pose a substantial health risk to the Iranian population. Further studies with more rigorous methods are recommended but this should not circumvent taking appropriate policy actions against these pollutants. Currently, Iran has no standard for dioxins and furans. Adaptation of the World Health Organization recommended guidelines might be an appropriate starting point to control dioxins and furans emissions.

In this research, probable arsenic contamination in drinking water in the city of Ardabil was studied in 163 samples during four seasons. In each season, sampling was carried out randomly in the study area. Results were analyzed statistically applying SPSS 19 software, and the data was also modeled by Arc GIS 10.1 software. The maximum permissible arsenic concentration in drinking water defined by the World Health Organization and Iranian national standard is 10 μg/L. Statistical analysis showed 75, 88, 47, and 69% of samples in autumn, winter, spring, and summer, respectively, had concentrations higher than the national standard. The mean concentrations of arsenic in autumn, winter, spring, and summer were 19.89, 15.9, 10.87, and 14.6 μg/L, respectively, and the overall average in all samples through the year was 15.32 μg/L. Although GIS outputs indicated that the concentration distribution profiles changed in four consecutive seasons, variance analysis of the results showed that statistically there is no significant difference in arsenic levels in four seasons.

Background: Atrazine is a herbicide that is widely used to control broadleaf and grassy weeds for growing many crops especially in maize production. It is a frequently detected herbicide in many groundwater resources. This study aimed to assess the feasibility of using ultraviolet radiation UV and fortified nanoparticles of titanium dioxide (TiO 2 ) doped with trivalent iron to remove atrazine from aqueous phase and determin the removal efficiency under the optimal conditions., Results: The results of this study demonstrated that the maximum atrazine removal rate was at pH = 11 in the presence of Fe + 3 -TiO 2 catalyst =25 mg/L and the initial concentration of atrazine equal to 10 mg/L. As the reaction time increased, the removal rate of herbicide increased as well. Atrazine removal rate was enhanced by the effect of UV radiation on catalyst activation in Fe +3 -TiO 2 /UV process. It was also revealed that pH has no significant effect on atrazine removal efficiency ( p  > 0.05)., Conclusion: Based on the data obtained in this study, atrazine removal efficiency was increased by increasing pH, initial atrazine concentration, catalyst, and contact time. The results also showed Fe +3 -TiO 2 /UV process was an appropriate method to reduce atrazine in contaminated water resources. In conclusion, Fe +3 -TiO 2 /UV process may enhance the rate of atrazine reduction in highly polluted water resources (more than 99%).

Background: In Iran, re-refinery industry has been developed many years ago based on the acid-clay treatment. Acidic sludge with high concentration of total petroleum hydrocarbon (TPH) is the final products of some facilities. In this study removal of TPH by aerated in-vessel composting was investigated., Methods: In order to microorganisms seeding and nutrient providing, urban immature compost was added as an amendment to acidic sludge. The ratios of acidic sludge (AS) to compost were, 1:0 (as control), 1:5, 1:8, 1:10, 1:15, 1:20, 1:30, 1:40, 1:50, 1:75 and 1:100 (as dry basis) at a C: N: P ratio of 100:5:1 and 45-65% moisture content for 70 days., Results: The removal efficiency in all reactors was more than 48%. The highest and lowest TPH removal was observed in 1:5 (71.56%) and 1:100 (48.53%) mixing ratios, respectively. The results of the control reactors showed that biological treatment was the main mechanism for TPH removal. Experimental data was fitted second order kinetic model ( R 2  > 0.8006). Degradation of TPH in 1:5 mixing ratio (k 2  = 0.0038 gmg -1 d -1 ; half-life = 3.08d) was nearly three times faster than 1:100 mixing ratio (k 2  = 0.0238; half-life = 8.96d). The results of the control reactors showed that biological treatment was the main mechanism for TPH removal., Conclusion: The results of this study revealed in-vessel composting with immature urban compost as the amendment maybe recommended as an effective method for TPH remediation.

Background: In this work, the magnetite (Fe 3 O 4 ) nanoparticles (MNPs) and silica-coated magnetite nanoparticles (SMNPs) were synthesized as adsorbents for removing humic acid (HA) from water resources., Methods: The adsorption processes were performed in batch experiments with which the influence of pH, reaction time, adsorbent dosage, initial concentrations of HA and temperature were investigated. Specific techniques were applied to characterize the features of both adsorbents (i. e. TECHNIQUES) (SEM, XRD, TEM, BET, EDX and VSM)., Results: The maximum saturation magnetization for SMNPs was 30.2 emu/g, which made its separation from the solution by a magnetic field to be easier and faster. The HA adsorption process onto the both adsorbents were best described by the Freundlich isotherm and pseudo-second-order kinetic models. Highest adsorption efficiency of HA by MNPs an d SMNPs occurred at acidic conditions (pH ≈ 3). The mechanisms of adsorption process involved with a physisorption process such as (i. e. hydrogen bonding and electrostatic interaction). The predicted maximum monolayer adsorption capacities obtained by Langmuir isotherm model for MNPs and SMNPs were 96.15 and 196.07 mg/g, respectively., Conclusion: Higher amount of HA adsorption onto the surfaces of SMNPs than MNPs surfaces was observed, reflecting that silica impregnated on MNPs enhances the efficiency of the adsorbent in removing HA.

The occurrences of Cryptosporidium and Giardia in surface sources of drinking water in Tehran were monitored, using US EPA method 1623.1. The prevalence ratios (PR) of positive samples among other media (animal's stools, vegetables, and human's stools) were also estimated from literature data. The density of Giardia and Cryptosporidium in water samples were 0.129 ± 0.069 cysts/L and 0.005 ± 0.002 oocysts/L, respectively. Estimated PR in vegetables, animal stools, surface waters, and human stools were 6.65, 20.42, 21.05, and 4.28 % for Cryptosporidium and 6.46, 17.13, 73.68, and 15.65 % for Giardia, respectively. These reveal the importance of surface waters' and animal stools' roles in the prevalence of cryptosporidiosis and giardiasis in Tehran's population. Giardia's prevalence in untreated surface waters in Tehran was found 3.5 times as much as Cryptosporidium while this found 2.3 times on a global scale. Moreover, the prevalence of giardiasis to cryptosporidiosis infections in Tehran's human population was 3.65. These values could be a clue to attribute the infections to the occurrence of parasites in surface waters. Significant (p < 0.05) associations were observed between rainfalls and presence of Giardia (r = 0.62) and Cryptosporidium (r = 0.60) in surface waters. In autumn, rainfalls can increase the parasites occurrences in surface waters. Significant (p < 0.05) difference on the density of parasites was found between some seasons using Kruskal-Wallis and multiple comparison tests. A significant correlation (r = 0.86) between Giardia and Cryptosporidium densities also confirms the common sources of pollution in surface waters. Findings suggest that untreated surface waters in Tehran may be a potential route of human exposure to protozoan parasites.

Background: Antibiotics have been increasingly used for veterinary and medical purposes. The overuse of these compounds for these purposes can pollute the environment, water resources in particular. Tetracycline, among other forms of antibiotics, is one of the most applied antibiotic in aquaculture and veterinary medicine. The present study aimed to tack the traces of tetracycline in the effluents of municipal and hospital wastewater treatment plants, surface and groundwater resources and finally the drinking water provided from these water resources., Methods: The samples were taken from Fasha-Foyeh Dam, wells located at Varamin Plain, and Yaftabad; and also, wastewater samples were collected from the wastewater treatment plant effluents of Emam Khomeini Hospital and a municipal wastewater treatment plant which its effluent is being released to the surface water of the area covered in this work. 24 samples were collected in total during July 2012 to December 2012. The prepared samples were analyzed using high-performance liquid chromatography., Results: Based on the results, mean tetracycline levels in surface and ground water at nearby of animal farms was found to vary from 5.4 to 8.1 ng L(-1). Furthermore, the maximum TC concentration of 9.3 ng L(-1) was found to be at Yaft-Abad sampling station. Although tetracycline traces could not be detected in any investigated Hospital WWTP effluents, it was tracked in MWWTP effluent samples, in the concentration range of 280 to 540 ng l(-1)., Conclusion: The results showed that the concentration of TC in water resource near the animal farms is higher than the other sampling stations. This is related to the usage of antibiotic for animals. In fact, it caused the contamination of water resources and could contribute to radical changes in the ecology of these regions.

Background: Un-doped and N-doped TiO2 nano-particles with different nitrogen contents were successfully synthesized by a simple sol-gel method, and were characterized by X-ray diffraction, field emission scanning electron microscopy, Energy dispersive X-ray analysis and UV-visible diffuse reflectance spectra techniques. Then enhancement of sonocatalytic degradation of humic acid by un-doped and N-doped TiO2 nano-particles in aqueous environment was investigated. The effects of various parameters such as initial concentration of humic acid, N-doping, and the degradation kinetics were investigated., Results: The results of characterization techniques affirmed that the synthesis of un-doped and N-doped TiO2 nano-particles was successful. Degradation of humic acid by using different nano-particles obeyed the first-order kinetic. Among various nano-particles, N-doped TiO2 with molar doping ratio of 6 % and band gap of 2.92 eV, exhibited the highest sonocatalytic degradation with an apparent-first-order rate constant of 1.56 × 10(-2) min(-1)., Conclusions: The high degradation rate was associated with the lower band gap energy and well-formed anatase phase. The addition of nano-catalysts could enhance the degradation efficiency of humic acid as well as N-doped TiO2 with a molar ratio of 6 %N/Ti was found the best nano-catalyst among the investigated catalysts. The sonocatalytic degradation with nitrogen doped semiconductors could be a suitable oxidation process for removal of refractory pollutants such as humic acid from aqueous solution.

Background: Magnetic graphene oxide (Fe3O4@SiO2-GO) nanocomposite was fabricated through a facile process and its application as an excellent adsorbent for lead (II) removal was also demonstrated by applying response surface methodology (RSM)., Methods: Fe3O4@SiO2-GO nanocomposite was synthesized and characterized properly. The effects of four independent variables, initial pH of solution (3.5-8.5), nanocomposite dosage (1-60 mg L(-1)), contact time (2-30 min), and initial lead (II) ion concentration (0.5-5 mg L(-1)) on the lead (II) removal efficiency were investigated and the process was optimized using RSM. Using central composite design (CCD), 44 experiments were carried out and the process response was modeled using a quadratic equation as function of the variables., Results: The optimum values of the variables were found to be 6.9, 30.5 mg L(-1), 16 min, and 2.49 mg L(-1) for pH, adsorbent dosage, contact time, and lead (II) initial concentration, respectively. The amount of adsorbed lead (II) after 16 min was recorded as high as 505.81 mg g(-1) for 90 mg L(-1) initial lead (II) ion concentration. The Sips isotherm was found to provide a good fit with the adsorption data (KS = 256 L mg(-1), nS = 0.57, qm = 598.4 mg g(-1), and R(2) = 0.984). The mean free energy Eads was 9.901 kJ/mol which confirmed the chemisorption mechanism. The kinetic study determined an appropriate compliance of experimental data with the double exponential kinetic model (R(2) = 0.982)., Conclusions: Quadratic and reduced models were examined to correlate the variables with the removal efficiency of Fe3O4@SiO2-GO. According to the analysis of variance, the most influential factors were identified as pH and contact time. At the optimum condition, the adsorption yield was achieved up to nearly 100 %.

Pharmaceuticals are becoming widely distributed in waters and wastewaters and pose a serious threat to public health. The present study aimed to analyze non-steroidal anti-inflammatory drugs (NSAIDs) in surface waters, drinking water, and wastewater in Tehran, Iran. Thirty-six samples were collected from surface waters, tap water, and influent and effluent of municipal and hospital wastewater treatment plants (WWTP). A solid-phase extraction (SPE) followed by liquid chromatography-tandem mass spectrometry method was used for the determination of pharmaceuticals, namely ibuprofen (IBP), naproxen (NPX), diclofenac (DIC), and indomethacin (IDM). IBP was found in most of the samples and had the highest concentration. The highest concentrations of NSAIDs were found in the municipal WWTP influents and hospital WWTP effluents. In the municipal WWTP influent samples, the concentrations of IBP, NPX, DIC, and IDM were 1.05, 0.43, 0.23, and 0.11 μg/L, respectively. DIC was found only in one river sample. All NSAIDs were detected in tap water samples. However, their concentration was very low and the maximum values for IBP, NPX, DIC, and IDM were 47, 39, 24, and 37 ng/L, respectively, in tap water samples. Results showed that the measured pharmaceuticals were detected in all rivers with low concentrations in nanograms per liter range, except DIC which was found only in one river. Furthermore, this study showed that the aforementioned pharmaceuticals are not completely removed during their passage through WWTPs. A potential environmental risk of selected NSAIDs for the urban wastewater has been discussed. However, given their low measured concentrations, no ecotoxicological effect is suspected to occur.

This study aimed to characterize the effects of ethanol on the monopolar electrochemical process to remove Bacillus subtilis spores from drinking water. In particular, spores' destruction was tested by applying 20-100 mA current for 15-60 min to B. subtilis spores (10(2)-10(4) CFU/mL density), with stainless steel electrodes. The experimental results showed electrochemical removal of spores in the presence of 0.4 M ethanol at 15, 45, and 60 min and 5 mA/cm(2) current density. However, the use of ethanol or the electrochemical process alone did not eliminate B. subtilis spores at these time points. Overall, this study suggests that adding ethanol to the electrochemical process successfully removes B. subtilis spores from drinking water.

Background: In this study, a central composite design (CCD) was used for modeling and optimizing the operation parameters such as pH, initial tetracycline and persulfate concentration and reaction time on the tetracycline degradation using sono-activated persulfate process. The effect of temperature, degradation kinetics and mineralization, were also investigated., Results: The results from CCD indicated that a quadratic model was appropriate to fit the experimental data (p < 0.0001) and maximum degradation of 95.01 % was predicted at pH = 10, persulfate concentration = 4 mM, initial tetracycline concentration = 30.05 mg/L, and reaction time = 119.99 min. Analysis of response surface plots revealed a significant positive effect of pH, persulfate concentration and reaction time, a negative effect of tetracycline concentration. The degradation process followed the pseudo-first-order kinetic. The activation energy value of 32.01 kJ/mol was obtained for US/S2O8 (2-) process. Under the optimum condition, the removal efficiency of COD and TOC reached to 72.8 % and 59.7 %, respectively. The changes of UV-Vis spectra during the process was investigated. The possible degradation pathway of tetracycline based on loses of N-methyl, hydroxyl, and amino groups was proposed., Conclusions: This study indicated that sono-activated persulfate process was found to be a promising method for the degradation of tetracycline.

Monte Carlo techniques are widely employed in internal dosimetry to obtain better estimates of absorbed dose distributions from irradiation sources in medicine. Accurate 3D absorbed dosimetry would be useful for risk assessment of inducing deterministic and stochastic biological effects for both therapeutic and diagnostic radiopharmaceuticals in nuclear medicine. The goal of this study was to experimentally evaluate the use of Geant4 application for tomographic emission (GATE) Monte Carlo package for 3D internal dosimetry using the head portion of the RANDO phantom. GATE package (version 6.1) was used to create a voxel model of a human head phantom from computed tomography (CT) images. Matrix dimensions consisted of 319 × 216 × 30 voxels (0.7871 × 0.7871 × 5 mm(3)). Measurements were made using thermoluminescent dosimeters (TLD-100). One rod-shaped source with 94 MBq activity of (99m)Tc was positioned in the brain tissue of the posterior part of the human head phantom in slice number 2. The results of the simulation were compared with measured mean absorbed dose per cumulative activity (S value). Absorbed dose was also calculated for each slice of the digital model of the head phantom and dose volume histograms (DVHs) were computed to analyze the absolute and relative doses in each slice from the simulation data. The S-values calculated by GATE and TLD methods showed a significant correlation (correlation coefficient, r(2) ≥ 0.99, p < 0.05) with each other. The maximum relative percentage differences were ≤14% for most cases. DVHs demonstrated dose decrease along the direction of movement toward the lower slices of the head phantom. Based on the results obtained from GATE Monte Carlopackage it can be deduced that a complete dosimetry simulation study, from imaging to absorbed dose map calculation, is possible to execute in a single framework.

Background: Nowadays, study and application of modified membranes for water treatment have been considered significantly. The aim of this study was to prepare and characterize a polysulfone (PSF)/graphene oxide (GO) nanocomposite membrane and to evaluate for arsenate rejection from water., Materials and Methods: The nanocomposite PSF/GO membrane was fabricated using wet phase inversion method. The effect of GO on the synthesized membrane morphology and hydrophilicity was studied by using FE-SEM, AFM, contact angle, zeta potential, porosity and pore size tests. The membrane performance was also evaluated in terms of pure water flux and arsenate rejection., Results: ATR-FTIR confirmed the presence of hydrophilic functional groups on the surface of the prepared GO. FE-SEM micrographs showed that with increasing GO content in the casting solution, the sub-layer structure was enhanced and the drop like voids in the pure PSF membrane changed to macrovoids in PSF/GO membrane along with increase in porosity. AFM images indicated lower roughness of modified membrane compared to pure PSF membrane. Furthermore, contact angle measurement and permeation experiment showed that by increasing GO up to 1 wt%, membrane hydrophilicity and pure water flux were increased. For PSF/GO-1, pure water flux was calculated about 50 L/m(2)h at 4 bar. The maximum rejection was obtained by PSF/GO-2 about 83.65 % at 4 bar. Moreover, it was revealed that arsenate rejection depended on solution pH values. It was showed that with increasing pH, the rejection increased., Conclusions: This study showed that application of GO as an additive to PSF casting solution could enhance the membrane hydrophilicity, porosity, flux and arsenate rejection.

Background: Mercury is considered as a toxic heavy metal in aquatic environments due to accumulation in bodies of living organisms. Exposure to mercury may lead to different toxic effects in humans including damages to kidneys and nervous system., Materials and Methods: Multi-walled carbon nanotubes (MWCNTs) were selected as sorbent to remove mercury from aqueous solution using batch technique. ICP instrument was used to determine the amount of mercury in solution. Moreover, pH, contact time and initial concentration of mercury were studied to determine the influence of these parameters on the adsorption conditions., Results: Results indicate that the adsorption strongly depended on pH and the best pH for adsorption is about 7. The rate of adsorption process initially was rapid but it was gradually reduced with increasing of contact time and reached the equilibrium after 120 min. In addition, more than 85 % of initial concentration of 0.1 mg/l was removed at 0.5 g/l concentration of sorbent and contact time of 120 min. Meanwhile, the adsorption process followed the pseudo second-order model and the adsorption isotherms could be described by both the Freundlich and the Langmuir models., Conclusion: This study showed that MWCNTs can effectively remove inorganic mercury from aqueous solutions as adsorbent.

Hierarchical distance-based fuzzy multi-criteria group decision making was served as a tool to evaluate the drinking water supply systems of Qom, a semi-arid city located in central part of Iran. A list of aspects consisting of 6 criteria and 35 sub-criteria were evaluated based on a linguistic term set by five decision-makers. Four water supply alternatives including "Public desalinated distribution system", "PET Bottled Drinking Water", "Private desalinated water suppliers" and "Household desalinated water units" were assessed based on criteria and sub-criteria. Data were aggregated and normalized to apply Performance Ratings of Alternatives. Also, the Performance Ratings of Alternatives were aggregated again to achieve the Aggregate Performance Ratings. The weighted distances from ideal solution and anti-ideal solution were calculated after secondary normalization. The proximity of each alternative to the ideal solution was determined as the final step. The alternatives were ranked based on the magnitude of ideal solutions. Results showed that "Public desalinated distribution system" was the most appropriate alternative to supply the drinking needs of Qom population. Also, "PET Bottled Drinking Water" was the second acceptable option. A novel classification of alternatives to satisfy the drinking water requirements was proposed which is applicable for the other cities located in semi-arid regions of Iran. The health issues were considered as independent criterion, distinct from the environmental issues. The constraints of high-tech alternatives were also considered regarding to the level of dependency on overseas.

In this study vertically aligned carbon nanotubes (VA-CNT) was grown on anodized aluminum oxide (AAO) substrate. The synthesized AAO-CNT membrane was characterized using Raman spectroscopy, field emission scanning electron microscopy (FESEM), contact angle and BET. The pure water flux, humic acid (HA) (as representative of natural organic matters) rejection and fouling mechanism were also evaluated. The fabricated membrane has pore density of 1.3 × 10(10) pores per cm(2), average pore size of 20 ± 3 nm and contact angle of 85 ± 8(o). A significant pure water flux of 3600 ± 100 L/m(2).h was obtained at 1 bar of pressure by this membrane due to the frictionless structure of CNTs. High contact angle exhibited the hydrophobic property of the membrane. It was revealed that HA is primarily rejected by adsorption in the membrane pores due to hydrophobic interactions with HA. Flux decline occurred rapidly through both cross flow and dead end filtration of the HA. Based on the blocking laws, internal pore constriction is dominant fouling mechanism in which HA adsorbs in membrane pores results in pores blockage and flux decline.

The amount of wastewater characteristics loading is one of the main parameters in the design of wastewater collection and treatment systems. The generation per capita per day (GPCD) of wastewater characteristics was estimated by analyzing the monthly data of nine wastewater treatment plants in Tehran, capital city of Iran. GPCD values were calculated from measured collected wastewater flow, the population and concentration data. The results indicated the values of 32.96 ± 1.91, 49.25 ± 2.49, 37.31 ± 2.44, 6.77 ± 0.53, 1.96 ± 0.11, 92.23 ± 5.68, 2.07 ± 0.39 and 128.96 ± 6.69 g/d.cap of GPCD for BOD5, COD, TSS, TKN, P, TDS, ON and TS, respectively, for Tehran's wastewater. The per capita estimated for the wastewater production and treatment were determined to be 186.06 ± 7.85 and 136.72 ± 5.43 L/d.cap, respectively. It is estimated that about 504 m(3)/d and 346 m(3)/d of sludge, will be produced and waste as excrement raw sludge, respectively, in Tehran. Simple regression models were presented the relationships such as the change of collected and treated wastewater with population and changes of GPCD parameters with each other. It was revealed that the Tehran's wastewater may be classified as highly degradable, but during recent decades its Biodegradability Index (BI) has been reduced up to 15%. The new suggested revised per capita parameters can be used for design purposes in Tehran, and possibly, in areas with similar characteristics, substituting the classical values obtained from foreign textbooks. These values could help in designing more accurate treatment systems and may lower the required capacity for the treatment of wastewater up to 40% in Tehran.

Bioremediation has shown its applicability for removal of polycyclic aromatic hydrocarbons (PAHs) from soil and sediments. In the present study, the effect of biostimulation on phenanthrene removal from contaminated soil via adding macro and/or micronutrients and trace elements was investigated. For these purposes three macro nutrients (as N, P and K), eight micronutrients (as Mg, S, Fe, Cl, Zn, Mn, Cu and Na) and four trace elements (as B, Mo, Co and Ni) in 11 mineral salts (MS) as variables were used. Placket-Burman statistical design was used to evaluate significance of variables (MS) in two levels of high and low. A consortium of adapted microorganisms with PAHs was used for inoculation to the soil slurry which was spiked with phenanthrene in concentration of 500 mg/kg soil. The optimal reduction resulted when a high level of macro nutrient in the range of 67-87% and low level of micro nutrient in the range of 12-32% were used with the nitrogen as the dominant macronutrient. The Pareto chart showed that NH4NO3 was the most effective variable in this experiment. The effect of elements on phenanthrene biodegradation showed following sequence as N > K > P > Cl > Na > Mg. Effectiveness of the other elements in all runs was less than 1%. The type and concentration of nutrient can play an important role in biodegradation of phenanthrene. Biostimulation with suitable combination of nutrient can enhance bioremediation of PAHs contaminated soils.

Background: Use of earthworm to eliminate the phenanthrene from the soil (bioaccumulation) is developed as an economical method. Bioaugmentation of microorganism was used for promotion of bioaccumulation by earthworm. The aim of this study was to determine the bioaccumulation or biodegradation of phenanthrene by Eisenia fetida and bacterial consortium in polluted soil., Methods: The amount of 0.4 kg of the polluted soil in the ratio of 10 and 30 mg phenanthrene per kg of dry soil was transferred into each pot. Afterwards, bacteria and earthworms were added to each pot in separate and combination. The samples were kept under field conditions, and the retention concentrations of phenanthrene were analyzed after 8 weeks., Results: Results showed that the Eisenia fetida was able to significantly remove phenanthrene from the polluted soil samples. Bioaccumulation and bioaugmentation alone have the removal efficiency of 60.24% and 50.3%, respectively. In the combined mode, phenanthrene removal efficiency was 63.81%., Conclusions: The current study indicated that the use of earthworms, could improve both phenanthrene bioavailability and microbial activity, which led to enhancing removal of carbon-based pollutants.

Background: In this Research, oyster shell supported zero valent iron nanoparticles were prepared and applied for the removal of natural organic matters (NOMs) from aqueous solutions under different experimental conditions., Methods: The nanoadsorbents prepared by wet impregnation method, then characterized using Scanning Electron Microscopy, Energy Dispersive Spectroscopy, X-Ray Fluorescence and BET analysis. Adsorption test was done in a batch reactor and the effects of different parameters such as initial adsorbate concentration, adsorbent dose, adsorption kinetic, pH, and temperature on removal of NOMs (humic acid as the indicator) were studied., Results: Results showed that particle size of nanoadsorbent was in the range of 60-83 nm, and surface area and micropore volume as 16.85 m(2)/g and 0.021 m(3)/g, respectively; the main elements of adsorbent were Ca, O, Fe and Na and lime, as high as about 94.25% was the main structural component of the total weight. Produced nanoadsorbent was not soluble in water. It was also shown that by increasing the nanoadsorbent dose from 0.5 to 5 g/100 ml, the removal of humic acid increased from 62.3% to 97.4%. An inverse relationship was found between initial concentration and adsorption capacity, so that a decreasing rate of 33% for humic acid removal was observed by increasing pH from 5 to 10. Temperature increase from 25°C to 40°C, resulted in an increase in humic acid removal from 76.8% to 91.4% and its adsorption on the adsorbent could be better described by Freundlich isotherm (n = 0.016, Kf = 0.013 and R(2) = 0.74). The most fitted adsorption kinetic model was pseudo-second order model., Conclusions: The chemical structure of nanoadsorbent was proper and free from harmful substances. Despite the relative good condition of the effective surface, due to the large size of the shell, the overall micropore volume was low. Hence the qualitative characteristics the adsorbent caused the absorption capacity of humic acid to be low (0.96 mg/g).

In this study Fe (III)-doped TiO2 nanoparticles were synthesized by sol-gel method at two atomic ratio of Fe/Ti, 0.006 and 0.034 percent. Then the photoactivity of them was investigated on degradation of phenol under UV (<380 nm) irradiation and visible light (>380 nm). Results showed that at appropriate atomic ratio of Fe to Ti (% 0.034) photoactivity of Fe(III)-doped TiO2 nanoparticles increased. In addition, the effects of various operational parameters on photocatalytic degradation, such as pH, initial concentration of phenol and amount of photocatalyst were examined and optimized. At all different initial concentration, highest degradation efficiency occurred at pH = 3 and 0.5 g/L Fe(III)-doped TiO2 dosage. With increase in initial concentration of phenol, photocatalytic degradation efficiency decreased. Photoactivity of Fe (III)-doped TiO2 under UV irradiation and visible light at optimal condition (pH = 3 and catalyst dosage = and 0.5 g/L) was compared with P25 TiO2 nanoparticles. Results showed that photoactivity of Fe(III)-doped TiO2 under visible light was more than P25 TiO2 photoactivity, but it was less than P25 TiO2 photoactivity under UV irradiation. Also efficiency of UV irradiation alone and amount of phenol adsorption on Fe(III)-doped TiO2 at dark condition was investigated.

In this work, synthetic nanoscale zerovalent iron (NZVI) stabilized with two polymers, Starch and Carboxymethyl cellulose (CMC) were examined and compared for their ability in removing As (III) and As (V) from aqueous solutions as the most promising iron nanoparticles form for arsenic removal. Batch operations were conducted with different process parameters such as contact time, nanoparticles concentration, initial arsenic concentration and pH. Results revealed that starch stabilized particles (S-nZVI) presented an outstanding ability to remove both arsenate and arsenite and displayed ~ 36.5% greater removal for As (V) and 30% for As (III) in comparison with CMC-stabilized nanoparticles (C-nZVI). However, from the particle stabilization viewpoint, there is a clear trade off to choosing the best stabilized nanoparticles form. Removal efficiency was enhanced with increasing the contact time and iron loading but reduced with increasing initial As (III, V) concentrations and pH. Almost complete removal of arsenic (up to 500 μg/L) was achieved in just 5 min when the S-nZVI mass concentration was 0.3 g/L and initial solution pH of 7 ± 0.1. The maximum removal efficiency of both arsenic species was obtained at pH = 5 ± 0.1 and starched nanoparticles was effective in slightly acidic and natural pH values. The adsorption kinetics fitted well with pseudo-second-order model and the adsorption data obeyed the Langmuir equation with a maximum adsorption capacity of 14 mg/g for arsenic (V), and 12.2 mg/g for arsenic (III). It could be concluded that starch stabilized Fe(0) nanoparticles showed remarkable potential for As (III, V) removal from aqueous solution e.g. contaminated water.

Background: Anomalous use of antibiotics and their entrance into the environment have increased concerns around the world. These compounds enter the environment through an incomplete metabolism and a considerable amount of them cannot be removed using conventional wastewater treatment. Therefore, the main objectives of this research are evaluation of the feasibility of using ultraviolet radiation (UV-A) and fortified nanoparticles of titanium dioxide (TiO2) doped with Fe+3 to remove penicillin G (PENG) from aqueous phase and determining the optimum conditions for maximum removal efficiency., Results: The results showed that the maximum removal rate of penicillin G occurred in acidic pH (pH = 3) in the presence of 90 mg/L Fe+3-TiO2 catalyst. In addition, an increase in pH caused a decrease in penicillin G removal rate. As the initial concentration of penicillin G increased, the removal rate of antibiotic decreased. Moreover, due to the effect of UV on catalyst activation in Fe+3-TiO2/UV-A process, a significant increase was observed in the rate of antibiotic removal. All of the variables in the process had a statistically significant effect (p < 0.001)., Conclusion: The findings demonstrated that the antibiotic removal rate increased by decreasing pH and increasing the amount of catalyst and contact time. In conclusion, Fe+3-TiO2/UV-A process is an appropriate method for reducing penicillin G in polluted water resources.

In this study, a new strategy in catalytic ozonation removal method for degradation of phenol from industrial wastewater was investigated. Magnetic carbon nano composite as a novel catalyst was synthesized, characterized and then used in the catalytic ozonation process (COP) and compared with the single ozonation process (SOP). The influential parameters were all investigated. The results showed that the removal efficiency of phenol and COD (chemical oxygen demand) in COP (98.5%, 69.8%) was higher than those of SOP (78.7%, 50.5%) and the highest catalytic potential was achieved at optimal neutral pH. First order modeling demonstrated that the reactions were dependent on the concentration of catalyst, with kinetic constants varying from 0.023 1/min (catalyst = 0 g/L) to 0.071 1/min (catalyst = 4 g/L), whereby the optimum dosage of catalyst was found to be 2 g/L. Furthermore, the catalytic properties of the catalyst remained almost unchanged after 5-time reuse. The results regarding the biodegradability of the effluent showed that a 5-min reaction time in COP reduced the concentrations of phenol and COD to the acceptable levels for the efficient post-treatment in the SBR in a 4-h cycle period. Finally, this combined system is proven to be a technically effective method for treating phenolic contaminants.

Background: Mono aromatic hydrocarbons (BTEX) are a group of hazardous pollutants which originate from sources such as refineries, gas, and oil extraction fields, petrochemicals and paint and glue industries.Conventional methods, including incineration, condensation, adsorption and absorption have been used for removal of VOCs. None of these methods is economical for removal of pollutants of polluted air with low to moderate concentrations. The heterogeneous photocatalytic processes involve the chemical reactions to convert pollutant to carbon dioxide and water. The aim of this paper is a comparison of Benzene & Toluene removal from synthetic polluted air using a Nano photocatalytic TiO2/ ZNO process., Results: The X-ray diffraction (XRD) patterns showed that Nano crystals of TiO2 and ZNO were in anatase and rutile phases. Toluene & benzene were decomposed by TiO2/ ZNO Nano photocatalyst and UV radiation. Kruskal-wallis Test demonstrated that there are significant differences (pvalue < 0.05) between pollutant concentrations in different operational conditions., Conclusions: Degradation of toluene & benzene increases with increasing UV intensity and decreasing initial concentrations. Effect of TiO2/ZNO Nano photocatalyst on benzene is less than that on toluene. In this research, Toluene & benzene removal by TiO2/ZNO and UV followed first-order reactions.

Background: Low cost 2,4-Dichlorophenolyxacetic acid (2,4-D) widely used in controlling broad-leafed weeds is frequently detected in water resources. The main objectives of this research were focused on evaluating the feasibility of using granular activated carbon modified with acid to remove 2,4-D from aqueous phase, determining its removal efficiency and assessing the adsorption kinetics., Results: The present study was conducted at bench-scale method. The influence of different pH (3-9), the effect of contact time (3-90 min), the amount of adsorbent (0.1-0.4 g), and herbicide initial concentration (0.5-3 ppm) on 2,4-D removal efficiency by the granular activated carbon were investigated. Based on the data obtained in the present study, pH of 3 and contact time of 60 min is optimal for 2,4-D removal. 2,4-D reduction rate increased rapidly by the addition of the adsorbent and decreased by herbicide initial concentration (63%). The percent of 2,4-D reduction were significantly enhanced by decreasing pH and increasing the contact time. The adsorption of 2,4-D onto the granular activated carbon conformed to Langmuir and Freundlich models, but was best fitted to type II Langmuir model (R2 = 0.999). The second order kinetics was the best for the adsorption of 2,4-D by modified granular activated carbon with R2 > 0.99. Regression analysis showed that all of the variables in the process have been statistically significant effect (p < 0.001)., Conclusions: In conclusion, granular activated carbon modified with acid is an appropriate method for reducing the herbicide in the polluted water resources.

The use of plants to remove Poly-aromatic-hydrocarbons (PAHs) from soil (phytoremediation) is emerging as a cost-effective method. Phytoremediation of contaminated soils can be promoted by the use of adding microorganisms with the potential of pollution biodegradation (bioaugmentation). In the present work, the effect of bacterial consortium was studied on the capability of Sorghum and Onobrychis sativa for the phytoremediation of soils contaminated with phenanthrene and pyrene. 1.5 kg of the contaminated soil in the ratio of 100 and 300 mg phenanthrene and/or pyrene per kg of dry soil was then transferred into each pot (nine modes). The removal efficiency of natural, phytoremediation and bioaugmentation, separately and combined, were evaluated. The samples were kept under field conditions, and the remaining concentrations of pyrene and phenanthrene were determined after 120 days. The rhizosphere as well as the microbial population of the soil was also determined. Results indicated that both plants were able to significantly remove pyrene and phenanthrene from the contaminated soil samples. Phytoremediation alone had the removal efficiency of about 63% and 74.5% for pyrene and phenanthrene respectively. In the combined mode, the removal efficiency dramatically increased, leading to pyrene and phenanthrene removal efficiencies of 74.1% and 85.02% for Onobrychis sativa and 73.84% and 85.2% for sorghum, respectively. According to the results from the present work, it can be concluded that Onobrychis sativa and sorghum are both efficient in removing pyrene and phenanthrene from contamination and bioaugmentation can significantly enhance the phytoremediation of soils contaminated with pyrene and phenanthrene by 22% and 16% respectively.