Search

We examine numerically the uniaxially compressed stability of triaxially woven fabric (TWF) composites employing a proposed geometrically nonlinear finite composite plate element model with volume segmentation ABD constitutive relation, taking advantage of greatly reduced degrees of freedom. From satisfactory agreement with results from literature, numerous boundary conditions are explored for various aspect ratios in the buckling analysis. High dependencies of post-buckling patterns on plate aspect ratios are observed, from which a computationally time-saving characteristic equations have been defined before the occurrence of post-buckling state for practical convenience, best described on the basis of logarithmic critical buckling load and stiffness factor. These buckling characteristics have a direct general correlation to TWF’s aspect ratios and boundary rigidities. [ABSTRACT FROM AUTHOR]

Stacking sequence design is indispensable to make efficient use of the material properties of laminated composite materials. These laminated composites are usually fabricated from unidirectional plies of given thickness with fiber orientations limited to a small set of angles (e.g., 0°, +45°, –45°, and 90°). This leads to a combinatorial optimisation problem, which is rather complex to solve. In this paper, a new multi-population-based harmony search algorithm with dynamic interaction of populations, hybridised with a customised neighborhood algorithm to solve the layup sequence design problem of laminate composite plate is presented. Numerical experiments have been carried out by first considering the buckling and failure load optimisation of a laminate composite plate and later studies have been carried out using hybrid laminate plates for maximisation of buckling load and fundamental frequency with varied levels of hybridisation and for various plate aspect ratios. Numerical studies carried out in this paper clearly indicate that proposed dynamic hybrid adaptive harmony search algorithm is an effective combinatorial optimisation tool for stacking sequence optimisation of laminate composite structures and the computational performance is found to be superior when compared to other popular implementations of harmony search algorithm. [ABSTRACT FROM PUBLISHER]

Advanced grid stiffened composite cylindrical shell is widely adopted in advanced structures due to its exceptional mechanical properties. Buckling is a main failure mode of advanced grid stiffened structures in engineering, which calls for increasing attention. In this paper, the buckling response of advanced grid stiffened structure is investigated by three different means including equivalent stiffness model, finite element model and a hybrid model (H-model) that combines equivalent stiffness model with finite element model. Buckling experiment is carried out on an advanced grid stiffened structure to validate the efficiency of different modeling methods. Based on the comparison, the characteristics of different methods are independently evaluated. It is arguable that, by considering the defects of material, finite element model is a suitable numerical tool for the buckling analysis of advanced grid stiffened structures. [ABSTRACT FROM PUBLISHER]

In this study, the buckling and compressive failure of adhesively-bonded stepped-lap joints (with/without composite patches) composed of pultruded glass fiber-reinforced polymer composite laminates was investigated experimentally and numerically. Two-component epoxy adhesive was used for bonding purposes. Composite patches were woven glass-epoxy layer. They were added onto the conventional stepped-lap joints so that additional load transfer paths were created and localized stress concentrations near joint edge were reduced. The axial compression tests were performed and the results revealed that the buckling and failure load of new stepped lap composite joints with composite patches were significantly higher than the conventional stepped lap joints. The influence of the overlap length was evaluated. For both types of joints, a small increase was observed in failure loads by increase of the overlap length. Numerical results showed a very good agreement with experimental results. [ABSTRACT FROM AUTHOR]

A novel approach to the optimization of flexible columns against buckling is presented. The problem of determining the shape of the column that has possibly the largest critical buckling load of columns of a given length and volume is solved for composite materials. The objective of this study was to develop and design an optimized composite column against buckling. Determining what shape of column has the largest possible buckling load of composite column of a given length and volume was considered. Clamped-clamped supported column is an important limit case because it caused debate in many publications. Moreover, in this study, the optimization problem of the clamped-clamped column under buckling load, which was previously dealt with by Tadjbakhsh and Keller [5], Olhoff and Rasmussen [6] and Masur [7] is reinvestigated. It is also proved that the solutions of Tadjbakhsh and Keller, Olhoff and Rasmussen and Masur are not optimum for columns with clamped ends. The present model formulation considers columns for which crush is taken into account in the formulation of the column optimization problem, allowing for bimodal optimum solution. This leads to the necessity for both stability and crush criterion formulation of the optimization problem. The new proposed optimum model solution has been verified with numerical analysis using ANSYS and experimental data for columns with clamped-clamped ends. It was shown that the new proposed model was given the optimum solution for the clamped-clamped case. Detailed results are presented and discussed for clamped-clamped columns having circular cross-sectional configuration. As a result of this study, it was shown that results obtained in previous studies of variation optimum cross-sectional area for columns under compressive forces clamped-clamped ends were erroneous. The corrected optimum form was obtained and results checked by numerical calculations and experimental tests of composite columns. [ABSTRACT FROM AUTHOR]

The buckling of laminated metal-matrix composite (MMC) plates with a central square cutout were analyzed under compressive biaxial loading using the finite element approach. The MMC plates displayed some interesting buckling patterns and initial buckling shapes when subjected to different combination of hole sizes and boundary conditions. In the case of anti-symmetric, free-free boundary conditions, the MMC plates with central square cutout resist higher buckling loads as the hole size increased. Two laminated stacking sequences [90/0/0/90]2 and [45/-45/-45/45]2 were used in this study. For the same hole size, plate aspect ratio, and boundary conditions, the results showed that the critical buckling behavior of the plates were primarily influenced by the edge boundary conditions rather than by the laminated stacking sequences. The overall critical buckling analysis indicated that plates with clamped boundary conditions will take higher compressive loads than that of simply supported boundary conditions by a ratio of 2 to 1. [ABSTRACT FROM AUTHOR]