Search

We have demonstrated BiFeO3 (BFO) as a potential bilayer electrolyte for 650 °C low temperature solid oxide fuel cell application. The stoichiometric perovskite BFO is synthesized by wet chemistry, calcined at 500 °C and sintered at 850 °C. The crystalline structure is confirmed by X-ray diffraction spectroscopy, the atomic ratios (Bi : Fe) of 1.02 and 1.00 are determined by X-ray energy dispersive spectroscopy and inductively coupled plasma-mass spectroscopy, respectively. The X-ray photoelectron spectroscopy analysis indicates the presence of oxygen vacancies which can partially reduce Fe3+ and result in relatively high dielectric constant (6252 at 100 kHz) and ionic conductivity (>10−2 S cm−1 at 650 °C). The BFO is coated with an yttria-stabilized zirconia (YSZ) protective layer to avoid hydrogen reduction of BFO. This bilayer electrolyte exhibits a 1.6 times increase in maximum power density as compared with pure YSZ when a Ni–YSZ anode and lanthanum strontium cobalt ferrite (LSCF) cathode are used in the fuel cell at 650 °C.

High refractive index transparent nanocomposites have been developed by in situ polymerization of a precursor that contains functional monomers and surface modified anatase TiO2 nanoparticles for optoelectronic applications. The monomers are in the liquid form, so environmentally friendly solventless precursors can be prepared. The precursor can be processed into various shapes or thick films (>50 microns) of the nanocomposite. The relationships of the chemical structure of the organic matrix, nanoparticle content and dispersity with the refractive index, transparency, mechanical and thermal properties are systematically investigated. The refractive index, and mechanical and thermal properties of the nanocomposite are increased with increasing TiO2 content and aromatic structure in the organic matrix due to their rigid characteristics. The transparency of the nanocomposite is increased with increasing TiO2 content and dispersity. At the same loading of nanoparticles, the higher dispersity and the better transparency are due to the less extent of Rayleigh scattering. At 18 vol% (60 wt%) of TiO2, the acetic acid modified TiO2/poly(4-vinyl benzyl alcohol) nanocomposite has a refractive index of 1.73 and excellent transparency (>85% from 500 nm to 800 nm). The refractive index of the nanocomposite can be further increased to 1.77 by replacing aliphatic acetic acid modified TiO2 with aromatic phenyl acetic acid modified TiO2. The results of this work provide new knowledge and a new pathway to design a polymer based high refractive index material.

Conjugated polymers are promising materials for oxygen sensing owing to their specific interaction with oxygen molecules and also advantages of low cost, easy processing and room temperature operation. The present work for the first time demonstrates an oxygen sensing material of poly(3-hexylethiophene) (P3HT)–TiO2 nanorod hybrid thin film which reveals considerable improvement of sensing response as compared to the pristine P3HT film. The effects of hybrid composition and film thickness on sensing performance were systematically investigated. Kelvin probe force microscopy (KPFM) was employed to understand the mechanism of oxygen sensing including the control of surface morphologies and electronic properties by TiO2 incorporation. The hybrid material developed in this study is helpful in the advancement of room temperature oxygen sensing technology.

The poly(3-hexyl thiophene):TiO2 nanorod (P3HT:TiO2) solar cell has a better thermal stability than the P3HT:PCBM solar cell; however, the former has a lower power conversion efficiency (PCE) than the latter. We would like to enhance the PCE of P3HT:TiO2 solar cell by improving the electron mobility of anatase TiO2 nanorods. Two novel approaches: (1) ripening and (2) boron doping for TiO2 nanorods were explored. TiO2 nanorods were synthesized first by sol–gel process in the presence of an oleic acid surfactant at 98 °C for 10 h. The size of the TiO2 nanocrystal is about 35 nm in length and 5 nm in diameter. The insulating oleic acid on the TiO2 nanorods was replaced by pyridine (as-synthesized TiO2) for good compatibility and charge transport between P3HT and TiO2 in the application of hybrid P3HT:TiO2 nanorod solar cells. The crystallinity of the as-synthesized TiO2 nanorods was increased through ripening (120 °C, 24 h) by using an autoclave reactor while the size of the nanocrystals was not significantly changed. Boron doped TiO2 nanorods (B-doped TiO2) were synthesized using the same sol–gel process of as-synthesized TiO2 nanorods but by replacing 0.7 at.% Ti with B using boron n-butoxide instead of titanium tetraisopropoxide. The UV-Vis spectroscopy and X-ray photoelectron spectroscopy (XPS) analyses indicate the B is present in TiO2 nanorods as substitutional defects which can be either Ti–O–B or O–Ti–B bonding, with a B 1 s binding energy of 192.1 eV. The ripening process is more effective at increasing the crystallinity of TiO2 nanorods than boron doping, as shown by XRD and Raman spectroscopy. The electron mobility of the TiO2 nanorods is improved from 6.21×10−5 to 2.33×10−4 (cm2 V−1 s) and 5.27×10−4 (cm2 V−1 s) for ripened TiO2 and B-doped TiO2, respectively, as compared with as-synthesized TiO2. The PCE of P3HT:TiO2 solar cells was increased by 1.31 times and 1.79 times under A. M. 1.5 illumination for ripened and B-doped TiO2, respectively, as compared with as-synthesized TiO2. The B-doped TiO2 has the highest mobility and PCE, mainly due to the presence of partially reduced Ti4+ by boron atom with delocalized electrons.