Search

Mixed-matrix membranes (MMMs) with metal-organic frameworks (MOFs) as additives (fillers) exhibit enhanced gas permeabilities and possibly also selectivities when compared to the pure polymer. Polyimides (Matrimid®) and polysulfones are popular polymer matrices for MOF fillers. Presently investigated MOFs for MMMs include [Cu(SiF(6))(4,4'-BIPY)(2)], [Cu(3)(BTC)(2)(H(2)O)(3)] (HKUST-1, Cu-BTC), [Cu(BDC)(DMF)], [Zn(4)O(BDC)(3)] (MOF-5), [Zn(2-methylimidazolate)(2)] (ZIF-8), [Zn(purinate)(2)] (ZIF-20), [Zn(2-carboxyaldehyde imidazolate)(2)] (ZIF-90), Mn(HCOO)(2), [Al(BDC)(μ-OH)] (MIL-53(Al)), [Al(NH(2)-BDC)(μ-OH)] (NH(2)-MIL-53(Al)) and [Cr(3)O(BDC)(3)(F,OH)(H(2)O)(2)] (MIL-101) (4,4'-BIPY = 4,4'-bipyridine, BTC = benzene-1,3,5-tricarboxylate, BDC = benzene-1,4-dicarboxylate, terephthalate). MOF particle adhesion to polyimide and polysulfone organic polymers does not represent a problem. MOF-polymer MMMs are investigated for the permeability of the single gases H(2), N(2), O(2), CH(4), CO(2) and of the gas mixtures O(2)/N(2), H(2)/CH(4), CO(2)/CH(4), H(2)/CO(2), CH(4)/N(2) and CO(2)/N(2) (preferentially permeating gas named first). Permeability increases can be traced to the MOF porosity. Since the porosity of MOFs can be tuned very precisely, which is not possible with polymeric material, MMMs offer the opportunity of significantly increasing the selectivity compared to the pure polymeric matrix. Additionally in most of the cases the permeability is increased for MMM membranes compared to the pure polymer. Addition of MOFs to polymers in MMMs easily yields performances similar to the best polymer membranes and gives higher selectivities than those reported to date for any pure MOF membrane for the same gas separation. MOF-polymer MMMs allow for easier synthesis and handability compared to pure MOF membranes.

Copolyimide membranes are established materials for the separation of gaseous and liquid mixtures. Cross-linking of the polymer strands improves the physical and chemical stability. The photo-cross-linking of a 6FDA-ODA/6FDA-DABA 4 : 1 copolyimide membrane containing maleimide side groups as linker was investigated by FTIR spectroscopy. IR absorption spectra of the copolyimide backbone, 3-hydroxypropyldimethyl maleimide and the copolyimide functionalized with 3-hydroxypropyldimethyl maleimide were measured before and after different irradiation times and compared to each other. For band assignment a normal mode analysis was performed. The backbone of the polymer and the maleimide linker can be well distinguished due to their different spectral band positions. Only the films containing a maleimide moiety perform a photoreaction, the polymer backbone does not interfere. Based on the difference spectra and the results of the DFT calculations it was shown that the trans- and the cis-cycloadduct as well as the previously suggested 2-2'-adduct without a cyclobutane ring are formed upon UV irradiation. Evidence for an oxetane-like photoproduct was not found. Different time constants for the increase of the product bands were observed. The cycloadduct accumulates with a shorter time constant (τ = 2 to 5 min) than the 2-2'-adduct (τ = 75 min). The yield of the photo-cross-linking reaction was determined by spectral deconvolution and kinetic fitting of several marker bands. For the copolyimide synthesized in this work, a maximum value of 6% was reached. The stiffness of the copolyimide backbone inhibits further photo-cross-linking.

Water-stable MIL-101 microcrystals adhere well to polysulfone (PSF) and yield a very robust mixed-matrix MIL-101-PSF membrane for the O(2)/N(2) separation with a selectivity of 5-6 and an unsurpassed O(2) permeability increase by a factor of four to above 6 barrer for MIL-101 loadings of 24%., (This journal is © The Royal Society of Chemistry 2012)