Search

Methanol as a green and renewable resource can be used to generate hydrogen by reforming, i.e., its catalytic oxidation with water. In combination with a fuel cell this hydrogen can be converted into electrical energy, a favorable concept, in particular for mobile applications. Its realization requires the development of novel types of structured catalysts, applicable in small scale reactor designs. Here, three different types of such catalysts were investigated for the steam reforming of methanol (SRM). Oxides such as TiO2 and CeO2 and mixtures thereof (Ce1Ti2Ox) were deposited inside a bulk nanoporous gold (npAu) material using wet chemical impregnation procedures. Transmission electron and scanning electron microscopy reveal oxide nanoparticles (1–2 nm in size) abundantly covering the strongly curved surface of the nanoporous gold host (ligaments and pores on the order of 40 nm in size). These catalysts were investigated in a laboratory scaled flow reactor. First conversion of methanol was detected at 200 °C. The measured turn over frequency at 300 °C of the CeOx/npAu catalyst was 0.06 s−1. Parallel investigation by in situ infrared spectroscopy (DRIFTS) reveals that the activation of water and the formation of OHads are the key to the activity/selectivity of the catalysts. While all catalysts generate sufficient OHads to prevent complete dehydrogenation of methanol to CO, only the most active catalysts (e.g., CeOx/npAu) show direct reaction with formic acid and its decomposition to CO2 and H2. The combination of flow reactor studies and in operando DRIFTS, thus, opens the door to further development of this type of catalyst. [ABSTRACT FROM AUTHOR]

Pulsed field gradient (PFG) NMR was applied to measure tortuosity factors for carbon dioxide diffusion in the Knudsen and gas regimes inside monoliths of a samaria–alumina aerogel catalyst, a high porosity material containing micropores in addition to meso- and macropores. The apparent tortuosity factor obtained from PFG NMR measurements for the Knudsen diffusion in the meso- and macropores of the catalyst has an unexpectedly large value of approximately 6 if carbon dioxide adsorption in the micropores and other types of surface adsorption sites of the catalyst is ignored. At the same time, the corresponding apparent tortuosity factor in the gas regime was found to be around 2. Application of a proposed model which describes fast molecular exchange between the surface adsorption sites and the main pore volume of the catalyst yields corrected tortuosity factors which depend only on the pore system geometry. Using this model, the corrected tortuosity factors were found to be around 2 for both diffusion regimes, in agreement with the expectations based on a high porosity of the studied catalyst. [ABSTRACT FROM AUTHOR]

The structural changes of a (111) oriented CeO2 film grown on a Si(111) substrate covered with a hex-Pr2O3(0001) interface layer due to post deposition annealing are investigated. X-ray photoelectron spectroscopy measurements revealing the near surface stoichiometry show that the film reduces continuously upon extended heat treatment. The film is not homogeneously reduced since several coexisting crystalline ceria phases are stabilized due to subsequent annealing at different temperatures as revealed by high resolution low energy electron diffraction and X-ray diffraction. The electron diffraction measurements show that after annealing at 660 °C the ι-phase (Ce7O12) is formed at the surface which exhibits a UGRAPHIC DISPLAY="INLINE" ID="UGT1" SRC="UGT1"/ structure. Furthermore, a UGRAPHIC DISPLAY="INLINE" ID="UGT2" SRC="UGT2"/ surface structure with a stoichiometry close to Ce2O3 is stabilized after annealing at 860 °C which cannot be attributed to any bulk phase of ceria stable at room temperature. In addition, it is shown that the fully reduced ceria (Ce2O3) film exhibits a bixbyite structure. Polycrystalline silicate (CeSixOy) and crystalline silicide (CeSi1.67) are formed at 850 °C and detected at the surface after annealing above 900 °C. [ABSTRACT FROM AUTHOR]

Using colloidally synthesized nanoparticles for the preparation of supported catalysts offers several advantages (e.g.precise control of particle size and morphology) when compared to traditional preparation techniques. Although such nanoparticles have already been very successfully used for catalytic applications in the liquid phase, applications in heterogeneous gas phase catalysis are still scarce. One aspect, usually considered as a problem, is organic stabilizers typically employed during the nanoparticle synthesis since they or their decomposition products are supposed to block catalytically active sites on the nanoparticle surface. Thus, in many studies so far, the removal of the organic ligands prior to use in gas phase catalysis has been proposed. In this perspective article, however, we will discuss a number of benefits such ligand shells may have for heterogeneous gas phase catalysis, including the protection against chemical modification, prevention of sintering and tuning of SMSI effects. [ABSTRACT FROM AUTHOR]

Microporous networks of Pt nanoparticles (NP) interlinked by aromatic diamines have recently shown prospects of application as hydrogen combustion catalysts in H 2 gas microsensors. In particular with respect to long-term sensor performance, they outperformed plain Pt NP as catalysts. In this paper, electron microscopy and Fourier transform infrared (FTIR) spectroscopy data on the stability of p -phenylene diamine (PDA) and of the PDA-linked Pt NP network structure during catalyst activation and long-term sensor operation at elevated temperature (up to 120-180 °C) will be presented. For the first time, all data were collected directly from microsensor catalysts, and FTIR was performed in operando , i.e. , during activation and sensor operation. While the data confirm high long-term catalyst activity far superior to that of plain Pt NP over 5 days of testing, they reveal that PDA fully decomposed during long-term sensor operation and that the network of discrete Pt nanoparticles changed to a sponge-like Pt nanostructure already during catalyst activation. These findings are at variance with previous work which assumed that stability of the PDA-linked Pt NP network is prerequisite for catalyst stability and performance., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (This journal is © The Royal Society of Chemistry.)

The rich surface chemistry of gold at the nanoscale has made it an important catalyst for low-temperature applications. Recent studies point to the possible role of self-organized structures formed by chemisorbed O atoms on the surface of gold catalysts for their catalytic activity and/or deactivation. In this study, we investigate the reactivity of a double O chain running along a step on a Au(221) surface with oxygen vacancies as a prototypical model of a 1D surface gold oxide. We compare CO and O 2 adsorption on such a chain with the oxygen-free Au(221) surface model. A systematic study of the reactivity of the double chain with O vacancies was done with respect to the regular Au(221) surface using CO as a probe. The CO oxidation was investigated assuming dissociative and associative mechanisms. Remarkably, O 2 adsorbs stronger on the double oxygen vacancy than on the regular Au(221) surface, and its dissociation barrier reduces significantly from 1.84 eV to 0.87 eV, whereas the CO adsorption energy is similar on these surfaces. Calculations suggest that CO oxidation should occur more efficiently on the double O vacancy than on the regular Au(221) surface due to stronger adsorption of O 2 and a low activation barrier for O 2 + CO surface reaction.

Dealloyed nanoporous metals hold great promise in the field of heterogeneous catalysis; however their tendency to coarsen at elevated temperatures or under catalytic reaction conditions sometimes limit further applications. Here, we report on a highly stable nanoporous gold catalyst (npAu) functionalized with praseodymia-titania mixed oxides as synthesized by a sol-gel method. Specifically, we used aberration-corrected transmission electron microscopy to study the morphology and the interface between the oxide deposits and the npAu substrate at the atomic level. Based on electron energy loss spectroscopy (EELS), it is concluded that Pr-TiOx mixed oxides form a solid solution. Flow reactor tests reveal that the Pr-TiOx functionalized nanoporous gold is not only highly active but also very stable for the water gas shift reaction in a large temperature range (180-400 °C). Our results demonstrate the potential of engineering the compositions of oxides coatings on npAu for advanced functional systems.

Bimetallic PtSn nanoparticles (NPs) of well-defined size and metal composition were prepared by means of colloidal methods. The mean particle diameter was about 2 nm for all samples irrespective of the Pt/Sn-ratio, which enables a systematic study of the influence of the composition on the catalytic properties while excluding particle size effects. The hydrogenation of crotonaldehyde was investigated as a reaction for which chemoselectivity is known to be a challenging task. Already very low atomic Sn contents (≈10%) were found to lead to a significantly improved activity which may be attributed to an electronic effect of Sn on Pt. For further increasing tin contents the activity decreased gradually. This trend was accompanied by a steady increase in selectivity towards the desired product (crotylalcohol). The results show that the highest crotylalcohol time yields can be obtained by using catalysts with an atomic Sn content of approximately 23%. In contrast, maximum crotylalcohol selectivities are achieved by using catalysts with a high tin content (>50%).

Rare earth praseodymium and cerium oxides have attracted intense research interest in the last few decades, due to their intriguing chemical and physical characteristics. An understanding of the correlation between structure and properties, in particular the surface chemistry, is urgently required for their application in microelectronics, catalysis, optics and other fields. Such an understanding is, however, hampered by the complexity of rare earth oxide materials and experimental methods for their characterisation. Here, we report recent progress in studying high-quality, single crystalline, praseodymium and cerium oxide films as well as ternary alloys grown on Si(111) substrates. Using these well-defined systems and based on a systematic multi-technique surface science approach, the corresponding physical and chemical properties, such as the surface structure, the surface morphology, the bulk-surface interaction and the oxygen storage/release capability, are explored in detail. We show that specifically the crystalline structure and the oxygen stoichiometry of the oxide thin films can be well controlled by the film preparation method. This work leads to a comprehensive understanding of the properties of rare earth oxides and highlights the applications of these versatile materials. Furthermore, methanol adsorption studies are performed on binary and ternary rare earth oxide thin films, demonstrating the feasibility of employing such systems for model catalytic studies. Specifically for ceria systems, we find considerable stability against normal environmental conditions so that they can be considered as a "materials bridge" between surface science models and real catalysts.

Different mono- and bifunctional amine ligands have been used to stabilize Pt NPs for catalytic H2 gas sensing. Depending on the chemical structure and properties of the ligand, the catalysts show different overall sensor performances, activation periods, and long-term stabilities. These sensor characteristics are put into relation with chemical processes like cleaning of the surface, degradation processes of the ligands and nanoparticle (NP) sintering. It has been found that during activation free adsorption sites are formed primarily due to desorption of synthetic residues. Furthermore, partial desorption of the ligands followed by their degradation may occur. For monoamines the latter process results in destabilization of the NPs followed by catalyst deactivation through particle sintering. The use of bifunctional ligands that link individual NPs shows significantly enhanced stabilities which can be related to the reduction of the ligand desorption rates and degradation. Besides the functionality of the ligands it was observed that the chemical nature of their hydrocarbon skeleton affects the catalyst stability: aromatic substructures remain intact upon H2 oxidation, while alkyl fragments undergo oxidation and decomposition. The advantages of bifunctionality and an aromatic hydrocarbon skeleton can be combined by the use of para-phenylenediamine (PDA) as a linking ligand. Networks formed by this ligand were indeed found to be stable under the applied catalytic conditions for more than 24 h.

A colloidal synthesis approach is presented that allows systematic studies of the properties of supported proton exchange membrane fuel cell (PEMFC) catalysts. The applied synthesis route is based on the preparation of monodisperse nanoparticles in the absence of strong binding organic stabilizing agents. No temperature post-treatment of the catalyst is required rendering the synthesis route ideally suitable for comparative studies. We report work concerning a series of catalysts based on the same colloidal Pt nanoparticle (NP) suspension, but with different high surface area (HSA) carbon supports. It is shown that for the prepared catalysts the carbon support has no catalytic co-function, but carbon pre-treatment leads to enhanced sticking of the Pt NPs on the support. An unwanted side effect, however, is NP agglomeration during synthesis. By contrast, enhanced NP sticking without agglomeration can be accomplished by the addition of an ionomer to the NP suspension. The catalytic activity of the prepared catalysts for the oxygen reduction reaction is comparable to industrial catalysts and no influence of the particle size is found in the range of 2-5 nm.

Recently, several forms of unsupported gold were shown to display a remarkable activity to catalyze oxidation reactions. Experimental evidence points to the crucial role of residual silver present in very small concentrations in these novel catalysts. We focus on the catalytic properties of nanoporous gold (np-Au) foams probed via CO and oxygen adsorption/co-adsorption. Experimental results are analyzed using theoretical models represented by the flat Au(111) and the kinked Au(321) slabs with Ag impurities. We show that Ag atoms incorporated into gold surfaces can facilitate the adsorption and dissociation of molecular oxygen on them. CO adsorbed on top of 6-fold coordinated Au atoms can in turn be stabilized by co-adsorbed atomic oxygen by up to 0.2 eV with respect to the clean unsubstituted gold surface. Our experiments suggest a linking of that most strongly bound CO adsorption state to the catalytic activity of np-Au. Thus, our results shed light on the role of silver admixtures in the striking catalytic activity of unsupported gold nanostructures.

Nanostructured materials are governed by their surface chemical properties. This is strikingly reflected by np-Au. This material can be generated by corrosion of bulk Ag-Au alloys. Based on a self-organisation process, a 3 dimensional sponge like gold structure evolves with ligaments in the range of only a few tens of nanometers. Due to its continuous porosity, the material can be penetrated by gases which then adsorb and interact with the surface. In this perspective we will review potential applications of np-Au resulting from this effect, namely heterogeneous gas phase catalysis, surface chemistry driven actuation, and adsorbate controlled stability of the nanostructure. We will summarize the current knowledge about the low temperature oxidation of CO as well as the highly selective oxidation of methanol. Furthermore, we will address the question how surface chemistry can influence the material properties itself. In particular, we will deal with (a) the actuation of np-Au by the reversible oxidation of its surface using ozone and (b) the adsorbate controlled coarsening of ligaments, using annealing experiments under ozone or inert gas atmosphere.

We investigated the decomposition and (partial) oxidation of methanol on Pd based catalysts in an integrated attempt, simultaneously bridging both the pressure and the materials gap. Combined studies were performed on well-defined Pd model catalysts based on ordered Al(2)O(3) and Fe(3)O(4) thin films, on well-defined particles supported on powders and on Pd single crystals. The interaction of Pd nanoparticles and Pd(111) with CH(3)OH and CH(3)OH/O(2) mixtures was examined from ultrahigh vacuum conditions up to ambient pressures, utilizing a broad range of surface specific vibrational spectroscopies which included IRAS, TR-IRAS, PM-IRAS, SFG, and DRIFTS. Detailed kinetic studies in the low pressure region were performed by molecular beam methods, providing comprehensive insights into the microkinetics of the reaction system. The underlying microscopic processes were studied theoretically on the basis of specially designed 3-D nanocluster models containing approximately 10(2) metal atoms. The efficiency of this novel modelling approach was demonstrated by rationalizing and complementing pertinent experimental results. In order to connect these results to the behavior under ambient conditions, kinetic and spectroscopic investigations were performed in reaction cells and lab reactors. Specifically, we focused on (1) particle size and structure dependent effects in methanol oxidation and decomposition, (2) support effects and their relation to activity and selectivity, (3) the influence of poisons such as carbon, and (4) the role of oxide and surface oxide formation on Pd nanoparticles.