Search

The effects of UV-induced bleaching of deep traps on Harshaw thermoluminescent (TL) LiF:Mg,Cu,P and LiF:Mg,Ti materials were investigated. During a normal heating cycle, LiF:Mg,Cu,P is limited to a maximum temperature of 240 °C. LiF:Mg,Ti can be read to higher temperatures; however, encapsulation in polytetrafluoroethylene limits the maximum readout temperature to 300 °C. Generally, for both materials, these respective temperatures are sufficient for emptying traps corresponding to the main dosemetric peaks. However, when the dosemeters are subjected to a high dose level, such as 1 Gy (much higher than individual monitoring dose levels), higher temperature traps are filled that cannot be emptied without exceeding the above-mentioned maximum temperatures. These high temperature traps tend to be unstable during normal readout and can significantly increase the residual TL signal. The purpose of this study was to investigate the applicability of a UV-induced bleaching technique for emptying higher temperature traps following high-dose applications. In addition, in the case of LiF:Mg,Cu,P, where the maximum readout temperature is significantly lower, we investigated the possibility of reducing the residual signal using the application of repeated readout cycles. The optical bleaching approach was found to be effective in the case of LiF:Mg,Ti; however, for LiF:Mg,Cu,P, no reduction in the residual signal was observed. For this latter material, the application of repeatable readout cycles is very effective and residual signals equivalent to dose levels as low as 0.01 mGy were observed following an initial dose of 5 Gy. To the best of our knowledge, this work is the first attempt to apply an 'optical annealing' technique to the Harshaw thermoluminescent dosemeter (TLD) materials.

Genetic diversity within and among 11 geographic populations of the beet webworm Loxostege sticticalis across five provinces in the northern part of China were evaluated using amplified fragment length polymorphism (AFLP) analysis. Five AFLP primer combinations were used on 88 L. sticticalis samples from different locations, detecting a total of 384 polymorphic and 27 monomorphic fragments. Although extensive genetic diversity occurs among individuals from different geographic populations (P = 93.4%, h = 0.398, I = 0.572), the majority of the genetic diversity is within populations and not between populations (G(ST) = 0.196), which agrees well with the results of analysis of molecular variance (84% of the total genetic variation is within populations), indicating high gene flow (N(M) = 2.046) among natural populations, which are not genetically differentiated. L. sticticalis in northeastern China, northern China, and northwestern China are part of a single large metapopulation. Cluster analyses based on AFLP data were preformed to graphically show groupings between individuals and between populations. Individuals from the same region were not grouped together very well. Eleven subpopulations were clustered into six broad groups, and there was no significant correlation between geographic distance and genetic dissimilarity (r = 0.1236, P = 0.8512). Principle component analysis also indicated a lack of genetic differentiation between the 11 populations. These results indicated that, although high genetic variability existed among individuals, there was little genetic differentiation among geographic populations, which can be explained by the effects of long distance migration of the beet webworm in China and consequent gene flow.

The sensitive stage for switching migrant oriental armyworm, Mythimna separata (Walker), into residents was determined under the stresses of starvation and cold (5 degrees C) in a laboratory population. Presumed migrants developing from gregarious larvae oviposited significantly earlier when adults were starved or shocked by cold only during the first 24 h after emergence. In contrast, preoviposition periods for migrants starved or cooled on days 2-6 of adult life were not significantly affected. The preresponse period of male migrants starved on day 1 of adult life was also significantly shortened, whereas those treated on following days were not significantly influenced. Similarly, total lifetime fecundity of migrants, which were starved or cooled on day 1 after emergence, was significantly increased; however, the same effect was not observed in migrants that were stressed later. Although preoviposition periods of presumed residents, developing from solitary larvae, starved or shocked by cold during the first several days of adulthood were significantly prolonged, this delay was not related to migratory strategy, because lifetime fecundity was not significantly reduced. The results suggest that the first day of adult life in this species is a sensitive stage during which migrants can shift into residents, although residents cannot shift to migrants. Thus, starvation and cold experienced in this stage induces migrants to modify their developmental path into reproduction and residency.

Genetic diversity within and among three wild-type natural populations and one melanic laboratory population of Mythimna separata (Walker) (Lepidoptera: Noctuidae) were evaluated using amplified fragment length polymorphism (AFLP) analysis. Although extensive genetic diversity occurs among individuals from different geographic populations (P = 54.5%, h = 0.209, I = 0.305), the majority of the genetic diversity is within populations and not between populations (G(ST) = 0.172), indicating high gene flow (N(M) = 2.403) and suggesting that M. separata in northern China are a part of a single large metapopulation. Genetic diversity in the natural populations was significantly higher than that in the melanic laboratory population (with P = 43.4% versus P = 25.9%, h = 0.173 versus h = 0.086, and I = 0.251 versus I = 0.127), suggesting that the melanic laboratory population is narrowly genetic-based and genetically uniform. Genetic similarities based on AFLP data were calculated, and cluster analysis was preformed to graphically display groupings between individuals and populations. Individuals from the same region were not grouped together in cluster analysis of three natural populations, whereas melanic individuals from laboratory population were grouped together very well. Four subpopulations were clustered into two broad groups. Melanic laboratory population became a single group, which had apparent differentiation from the other group in which three natural subpopulations were included. These results indicated that although high genetic variability existed among the individuals of natural populations, there was little genetic differentiation among three geographic populations that could be explained by the effects of the long distance migration of the oriental armyworm in China enhanced the level of gene flow. Influences of migration on the genetic polymorphism and differentiations that make a significant contribution to evolution in this insect are reviewed.

Melanism in the oriental armyworm Mythimna separata (Walker) is characterized by a black color in adults instead of the normal body color of off-white. Because inheritance of melanism in this moth follows Mendel's law, with the melanic allele (t) recessive to the normal allele (T) at a single autosomal locus, a backcrossing procedure was used to develop near isogenic lines (NILs) for melanic (NILs-tt) and typical forms (NILs-TT) of this moth. Melanic males (tt) and typical females (TT) were crossed in the laboratory, their progeny (F(1)) were interbred, and F(2) melanic males were backcrossed to typical female offspring of the parallel line. This cycle was repeated five times to create NILs for melanic and typical forms of this moth. The effects of the melanic allele on relative fitness were evaluated in terms of developmental and reproductive characteristics. Life tables of the NILs were constructed to determine net reproductive rate (R(0)). Results indicated that NILs-tt possessed apparent developmental and reproductive advantages, including shorter immature development time, higher larval and pupal survival, a shorter adult preoviposition period, and more eggs laid per female compared with the NILs-TT.

The Harshaw TLD system has three key calibration procedures: the Reader, the Dosemeter and the Algorithm. These functions must be properly calibrated for the system to achieve the optimum results. For the conventional reader and dosemeter calibration, Harshaw TLD recommends a pre-fade and a post-fade of 24-48 h when calibrating the system for LiF:Mg,Ti type dosemeter. It is also recommended that keeping the fade time consistent is important to maintain the quality of the system performance. In recent years, new calibration features have been introduced into the Harshaw TLD models 6600 and 8800 operating systems. These new features are Auto Calibration, Auto QC and Auto Blank, and they give the user the ability to set up the clear-expose-read process to be performed automatically in a sequence for each dosemeter. This saves processing time and keeps the fade time the same. However, since the fade time is near zero, will it affect the TLD system calibration factors? What should the user expect? This paper presents a study of the effect of Auto Calibration/Auto QC to the TLD operation.

A new type of extremity dosemeter, which incorporates the Harshaw TLD EXTRAD dosemeter element into a PVC finger stall, has been developed. The dosemeter uses high-sensitivity lithium fluoride, (7)LiF:Mg,Cu,P (TLD-700H) in a thin 7 mg cm(-2) layer, with alternative coverings of PVC at 10 mg cm(-2) and aluminised polyester at 3.2 mg cm(-2). Results are presented of the type testing of both versions of the finger stall dosemeter against published standards.

One of the advantages of LiF based thermoluminescent (TL) materials is its tissue-equivalent property. The Harshaw TLD-100H (LiF:Mg,Cu,P) material has demonstrated that it has a near-flat photon energy response and high sensitivity. With the optimized dosemeter filters built into the holder, the Harshaw TLD-100H two-element dosemeter can be used as a whole body personnel dosemeter for gamma, X ray and beta monitoring without the use of an algorithm or correction factor. This paper presents the dose performance of the Harshaw TLD-100H two-element dosemeter against the ANSI N13.11-2001 standard and the results of tests that are required in IEC 1066 International Standard.

Harshaw TLD-700H (7LiF:Mg,Cu,P) was previously characterised for low- to high-dose ranges from 1 microGy to 20 Gy. This paper describes the studies and results of dose-response and linearity at much higher doses. TLD-700H is a near perfect dosimetric material with near tissue equivalence, flat energy response, and the ability to measure beta, gamma and X rays. These new results extend the applicability of Harshaw TLD-700H into more dosimetric measurement environments. The simple glow curve structure provides insignificant fade, eliminating special oven preparation methods experienced by other materials. The work presented in this paper quantifies the performance of Harshaw TLD-700H in extended ranges.

The glow curve shape of LiF:Mg,Cu,P (MCP) material is studied in this research. The study is focused on the effects of the heating rate on the dosimetric peaks. Different configurations of dosemeters (chips, cards and powder) are studied. The shifting of the dominant dosimetric peak is observed and analysed. The curves are deconvoluted using the new Harshaw Glow Curve Analyser (GCA) program. Results of the study are presented, as well as possible explanations as to the observed effects.

LiF:Mg,Cu,P is starting to replace LiF:Mg,Ti in a variety of personnel dosimetry applications. LiF:Mg,Cu,P has superior characteristics as compared to LiF:Mg,Ti including, higher sensitivity, improved energy response for photons, lack of supralinearity and insignificant fading. The use of LiF:Mg,Cu,P in large scale dosimetry programs is of particular interest due to the extreme sensitivity of this material to the maximum readout temperature, and the variety of different dosimetry aspects and details that must be considered for a successful implementation in routine dosimetry. Here we discuss and explain the various aspects of large scale LiF:Mg,Cu,P based dosimetry programs including the properties of the TL material, new generation of TLD readers, calibration methodologies, a new generation of dose calculation algorithms based on the use of artificial neural networks and the overall uncertainty of the dose measurement. The United States Navy (USN) will be the first US dosimetry processor who will use this new material for routine applications. Until June 2002, the Navy used two types of thermoluminescent materials for personnel dosimetry, CaF2:Mn and LiF:Mg,Ti. A program to upgrade the system and to implement LiF:Mg,Cu,P, started in the mid 1990s and was recently concluded. In 2002, the new system replaced the LiF:Mg,Ti and is scheduled to start replacing the CaF2:Mn system in 2006. A pilot study to determine the dosimetric performance of the new LiF:Mg,Cu,P based dosimetry system was recently completed, and the results show the new system to be as good or better than the current system in all areas tested. As a result, LiF:Mg,Cu,P is scheduled to become the primary personnel dosimeter for the entire US Navy in 2006.

The Harshaw Model 6600 Plus is a reader with a capacity for 200 TLD cards or 800 extremity cards. The new unit integrates more functionality, and significantly automates the QC and calibration process compared to the Model 6600. The Model 6600 Plus was tested against the IEC 61066 (1991-2012) procedures using Harshaw TLD-700H and TLD-600H, LiF:Mg,Cu,P based TLD Cards. An overview of the type testing procedures is presented. These include batch homogeneity, detection threshold, reproducibility, linearity, self-irradiation, residue, light effects on dosemeter, light leakage to reader, voltage and frequency, dropping and reader stability. The new TLD reader was found to meet all the IEC criteria by large margins and appears well suited for whole body, extremity and environmental dosimetry applications, with a high degree of dosimetric performance.

Evaluation of a new extremity dosemeter is presented. The dosemeter is a passive device that is easy to wear and features a permanent individual numerical ID with barcode, a watertight case, an automatic TLD reader and database management software. Two dosemeters were studied: the first consists of a 100 mg x cm(-2) 7LiF:Mg,Ti (TLD-700) chip and a 42 mg x cm(-2) cap, the other consists of a 7 mg x cm(-2) layer of 7LiF:Mg,Cu,P (TLD-700H) powder and a 5 mg x cm(-2) cap. Sensitivity, repeatability, lower limit detection, angular responses and energy responses for these dosemeters are studied and presented. The dose calculation algorithm is developed and its dosimetric performance accuracy is compared with the standard ANSI N13.32-1995, Performance Testing of Extremity Dosemeters.