Search

This paper demonstrates multiphoton excited fluorescence imaging through a polarisation maintaining multicore fiber (PM-MCF) while the fiber is dynamically deformed using all-proximal detection. Single-shot proximal measurement of the relative optical path lengths of all the cores of the PM-MCF in double pass is achieved using a Mach-Zehnder interferometer read out by a scientific CMOS camera operating at 416 Hz. A non-linear least squares fitting procedure is then employed to determine the deformation-induced lateral shift of the excitation spot at the distal tip of the PM-MCF. An experimental validation of this approach is presented that compares the proximally measured deformation-induced lateral shift in focal spot position to an independent distally measured ground truth. The proximal measurement of deformation-induced shift in focal spot position is applied to correct for deformation-induced shifts in focal spot position during raster-scanning multiphoton excited fluorescence imaging.

We describe an angular multiplexed imaging technique for 3-D in vivo cell tracking of sparse cell distributions and optical projection tomography (OPT) with superior time-lapse resolution and a significantly reduced light dose compared to volumetric time-lapse techniques. We demonstrate that using dual axis OPT, where two images are acquired simultaneously at different projection angles, can enable localization and tracking of features in 3-D with a time resolution equal to the camera frame rate. This is achieved with a 200x reduction in light dose compared to an equivalent volumetric time-lapse single camera OPT acquisition with 200 projection angles. We demonstrate the application of this technique to mapping the 3-D neutrophil migration pattern observed over ~25.5 minutes in a live 2 day post-fertilisation transgenic LysC:GFP zebrafish embryo following a tail wound.

We investigate the potential of an instrument combining time-resolved spectrofluorometry and diffuse reflectance spectroscopy to measure structural and metabolic changes in cardiac tissue in vivo in a 16 week post-myocardial infarction heart failure model in rats. In the scar region, we observed changes in the fluorescence signal that can be explained by increased collagen content, which is in good agreement with histology. In areas remote from the scar tissue, we measured changes in the fluorescence signal (p < 0.001) that cannot be explained by differences in collagen content and we attribute this to altered metabolism within the myocardium. A linear discriminant analysis algorithm was applied to the measurements to predict the tissue disease state. When we combine all measurements, our results reveal high diagnostic accuracy in the infarcted area (100%) and border zone (94.44%) as well as in remote regions from the scar (> 77%). Overall, our results demonstrate the potential of our instrument to characterize structural and metabolic changes in a failing heart in vivo without using exogenous labels.

We describe a remote focal scanning technique for optical projection tomography (OPT) implemented with an electrically tunable lens (ETL) that removes the need to scan the specimen or objective lens. Using a 4× objective lens the average spatial resolution is improved by ∼46% and the light collection efficiency by a factor of ∼6.76, thereby enabling increased acquisition speed and reduced light dose. This convenient implementation is particularly appropriate for lower magnifications and larger sample diameters where axial objective scanning would encounter problems with speed and stability.

The editors introduce the Biomedical Optics Express feature issue "Optical Molecular Probes, Imaging, and Drug Delivery," which is associated with a Topical Meeting of the same name held at the 2013 Optical Society of America (OSA) Optics in the Life Sciences Congress in Waikoloa Beach, Hawaii, April 14-18, 2013. The international meeting focused on the convergence of optical physics, photonics technology, nanoscience, and photochemistry with drug discovery and clinical medicine. Papers in this feature issue are representative of meeting topics, including advances in microscopy, nanotechnology, and optics in cancer research.

We present an ex vivo study of temporally and spectrally resolved autofluorescence in a total of 47 endoscopic excision biopsy/resection specimens from colon, using pulsed excitation laser sources operating at wavelengths of 375 nm and 435 nm. A paired analysis of normal and neoplastic (adenomatous polyp) tissue specimens obtained from the same patient yielded a significant difference in the mean spectrally averaged autofluorescence lifetime -570 ± 740 ps (p = 0.021, n = 12). We also investigated the fluorescence signature of non-neoplastic polyps (n = 6) and inflammatory bowel disease (n = 4) compared to normal tissue in a small number of specimens.

We describe an angular multiplexing technique for optical projection tomography that improves resolution, signal-to-noise ratio, and imaging speed by ameliorating the trade-off between spatial resolution and depth of field and improving the light collection efficiency. Here we demonstrate that imaging at two orthogonal angular projections simultaneously, focused on shifted planes in the sample, improves the average spatial resolution by ~20% and the light collection efficiency by a factor of ~4, thereby enabling increased acquisition speed and reduced light dose.

We demonstrate two techniques to improve the quality of reconstructed optical projection tomography (OPT) images using the modulation transfer function (MTF) as a function of defocus experimentally determined from tilted knife-edge measurements. The first employs a 2-D binary filter based on the MTF frequency cut-off as an additional filter during back-projection reconstruction that restricts the high frequency information to the region around the focal plane and progressively decreases the spatial frequency bandwidth with defocus. This helps to suppress "streak" artifacts in OPT data acquired at reduced angular sampling, thereby facilitating faster OPT acquisitions. This method is shown to reduce the average background by approximately 72% for an NA of 0.09 and by approximately 38% for an NA of 0.07 compared to standard filtered back-projection. As a biological illustration, a Fli:GFP transgenic zebrafish embryo (3 days post-fertilisation) was imaged to demonstrate the improved imaging speed (a quarter of the acquisition time). The second method uses the MTF to produce an appropriate deconvolution filter that can be used to correct for the spatial frequency modulation applied by the imaging system.

We describe a new light transport model, which was applied to three-dimensional lifetime imaging of Förster resonance energy transfer in mice in vivo. The model is an approximation to the radiative transfer equation and combines light diffusion and ray optics. This approximation is well adopted to wide-field time-gated intensity-based data acquisition. Reconstructed image data are presented and compared with results obtained by using the telegraph equation approximation. The new approach provides improved recovery of absorption and scattering parameters while returning similar values for the fluorescence parameters.

We explore the diagnostic potential of imaging endogenous fluorophores using two photon microscopy and fluorescence lifetime imaging (FLIM) in human skin with two spectral detection channels. Freshly excised benign dysplastic nevi (DN) and malignant nodular Basal Cell Carcinomas (nBCCs) were excited at 760 nm. The resulting fluorescence signal was binned manually on a cell by cell basis. This improved the reliability of fitting using a double exponential decay model and allowed the fluorescence signatures from different cell populations within the tissue to be identified and studied. We also performed a direct comparison between different diagnostic groups. A statistically significant difference between the median mean fluorescence lifetime of 2.79 ns versus 2.52 ns (blue channel, 300-500 nm) and 2.08 ns versus 1.33 ns (green channel, 500-640 nm) was found between nBCCs and DN respectively, using the Mann-Whitney U test (p < 0.01). Further differences in the distribution of fluorescence lifetime parameters and inter-patient variability are also discussed.

When performing multiphoton fluorescence lifetime imaging in multiple spectral emission channels, an instrument response function must be acquired in each channel if accurate measurements of complex fluorescence decays are to be performed. Although this can be achieved using the reference reconvolution technique, it is difficult to identify suitable fluorophores with a mono-exponential fluorescence decay across a broad emission spectrum. We present a solution to this problem by measuring the IRF using the ultrafast luminescence from gold nanorods. We show that ultrafast gold nanorod luminescence allows the IRF to be directly obtained in multiple spectral channels simultaneously across a wide spectral range. We validate this approach by presenting an analysis of multispectral autofluorescence FLIM data obtained from human skin ex vivo.

Förster resonance energy transfer (FRET) is a powerful biological tool for reading out cell signaling processes. In vivo use of FRET is challenging because of the scattering properties of bulk tissue. By combining diffuse fluorescence tomography with fluorescence lifetime imaging (FLIM), implemented using wide-field time-gated detection of fluorescence excited by ultrashort laser pulses in a tomographic imaging system and applying inverse scattering algorithms, we can reconstruct the three dimensional spatial localization of fluorescence quantum efficiency and lifetime. We demonstrate in vivo spatial mapping of FRET between genetically expressed fluorescent proteins in live mice read out using FLIM. Following transfection by electroporation, mouse hind leg muscles were imaged in vivo and the emission of free donor (eGFP) in the presence of free acceptor (mCherry) could be clearly distinguished from the fluorescence of the donor when directly linked to the acceptor in a tandem (eGFP-mCherry) FRET construct.

We present an approach to laser scanning endomicroscopy that requires no moving parts and can be implemented with no distal scanners or optics, permitting extremely compact endoscopic probes to be developed. Our approach utilizes a spatial light modulator to correct for phase variations across a fiber imaging bundle and to encode for arbitrary wavefronts at the distal end of the fiber bundle. Thus, it is possible to realize both focusing and beam scanning at the output of the fiber bundle with no distal components. We present proof of principle results to illustrate three-dimensional scanning of the focal spot and exemplar images of a United States Air Force resolution test chart.

We demonstrate the application of fluorescence lifetime optical projection tomography (FLIM-OPT) to in vivo imaging of lysC:GFP transgenic zebrafish embryos (Danio rerio). This method has been applied to unambiguously distinguish between the fluorescent protein (GFP) signal in myeloid cells from background autofluorescence based on the fluorescence lifetime. The combination of FLIM, an inherently ratiometric method, in conjunction with OPT results in a quantitative 3-D tomographic technique that could be used as a robust method for in vivo biological and pharmaceutical research, for example as a readout of Förster resonance energy transfer based interactions.

Optical imaging of tissue autofluorescence has the potential to provide rapid label-free screening and detection of surface tumors for clinical applications, including when combined with endoscopy. Quantitative imaging of intensity-based contrast is notoriously difficult and spectrally resolved imaging does not always provide sufficient contrast. We demonstrate that fluorescence lifetime imaging (FLIM) applied to intrinsic tissue autofluorescence can directly contrast a range of surface tissue tumors, including in gastrointestinal tissues, using compact, clinically deployable instrumentation achieving wide-field fluorescence lifetime images of unprecedented clarity. Statistically significant contrast is observed between cancerous and healthy colon tissue for FLIM with excitation at 355 nm. To illustrate the clinical potential, wide-field fluorescence lifetime images of unstained ex vivo tissue have been acquired at near video rate, which is an important step towards real-time FLIM for diagnostic and interoperative imaging, including for screening and image-guided biopsy applications.

We report a three-dimensional time-resolved tomographic imaging technique for localizing protein-protein interaction and protein conformational changes in turbid media based on Förster resonant energy-transfer read out using fluorescence lifetime. This application of "tomoFRET" employs an inverse scattering algorithm utilizing the diffusion approximation to the radiative-transfer equation applied to a large tomographic data set of time-gated images. The approach is demonstrated by imaging a highly scattering cylindrical phantom within which are two thin wells containing cytosol preparations of HEK293 cells expressing TN-L15, a cytosolic genetically encoded calcium Förster resonant energy-transfer sensor. A 10 mM calcium chloride solution was added to one of the wells, inducing a protein conformation change upon binding to TN-L15, resulting in Förster resonant energy transfer and a corresponding decrease in the donor fluorescence lifetime. We successfully reconstruct spatially resolved maps of the resulting fluorescence lifetime distribution as well as of the quantum efficiency, absorption, and scattering coefficients.

Fluorescence lifetime imaging (FLIM) is used to quantitatively map the concentration of a small molecule in three dimensions in a microfluidic mixing device. The resulting experimental data are compared with computational fluid-dynamics (CFD) simulations. A line-scanning semiconfocal FLIM microscope allows the full mixing profile to be imaged in a single scan with submicrometer resolution over an arbitrary channel length from the point of confluence. Following experimental and CFD optimization, mixing times down to 1.3+/-0.4 ms were achieved with the single-layer microfluidic device.

We describe a simple implementation of a slit scanning confocal microscope to obtain an axial resolution better than that of a point-scanning confocal microscope. Under slit illumination, images of a fluorescent object are captured using an array detector instead of a line detector so that out-of-focus light is recorded and then subtracted from the adjacent images. Axial resolution after background subtraction is 2.2 times better than the slit confocal resolution, and out-of-focus image suppression is calculated to attenuate with defocus faster by 1 order of magnitude than in the point confocal case.

We demonstrate stimulated emission depletion (STED) microscopy implemented in a laser scanning confocal microscope using excitation light derived from supercontinuum generation in a microstructured optical fiber. Images with resolution improvement beyond the far-field diffraction limit in both the lateral and axial directions were acquired by scanning overlapped excitation and depletion beams in two dimensions using the flying spot scanner of a commercially available laser scanning confocal microscope. The spatial properties of the depletion beam were controlled holographically using a programmable spatial light modulator, which can rapidly change between different STED imaging modes and also compensate for aberrations in the optical path. STED fluorescence lifetime imaging microscopy is demonstrated through the use of time-correlated single photon counting.

We present a time-gated, optically sectioned, hyperspectral fluorescence lifetime imaging (FLIM) microscope incorporating a tunable supercontinuum excitation source extending into the UV. The system is capable of resolving the excitation spectrum, emission spectrum, and fluorescence decays in an optically sectioned image.

We present a time domain optically sectioned fluorescence lifetime imaging (FLIM) microscope developed for high-speed live cell imaging. This single photon excited system combines wide field parallel pixel detection with confocal sectioning utilizing spinning Nipkow disc microscopy. It can acquire fluorescence lifetime images of live cells at up to 10 frames per second (fps), permitting high-speed FLIM of cell dynamics and protein interactions with potential for high throughput cell imaging and screening applications. We demonstrate the application of this FLIM microscope to real-time monitoring of changes in lipid order in cell membranes following cholesterol depletion using cyclodextrin and to the activation of the small GTP-ase Ras in live cells using FRET.

The use of the time gating technique for lifetime reconstruction in the Fourier domain is a novel technique. Time gating provides sufficient data points in the time domain for reliable application of the Fourier transform, which is essential for the time deconvolution of the system of the integral equations employed in the reconstruction. The Fourier domain telegraph equation is employed to model the light transport, which allows a sufficiently broad interval of frequencies to be covered. Reconstructed images contain enough information needed for recovering the lifetime distribution in a sample for any given frequency within the megahertz-gigahertz band. The use of this technique is essential for recovering time-dependent information in fluorescence imaging. This technique was applied in reconstruction of the lifetime distribution of four tubes filled with Rhodamine 6G embedded inside a highly scattering slab. Relatively accurate fluorescence lifetime reconstruction demonstrates the effectiveness and the potential of the proposed technique.

We report a multifocal multiphoton time-correlated single photon counting (TCSPC) fluorescence lifetime imaging (FLIM) microscope system that uses a 16 channel multi-anode PMT detector. Multiphoton excitation minimizes out-of-focus photobleaching, multifocal excitation reduces non-linear in-plane photobleaching effects and TCSPC electronics provide photon-efficient detection of the fluorescence decay profile. TCSPC detection is less prone to bleaching- and movement-induced artefacts compared to wide-field time-gated or frequency-domain FLIM. This microscope is therefore capable of acquiring 3-D FLIM images at significantly increased speeds compared to single beam multiphoton microscopy and we demonstrate this with live cells expressing a GFP tagged protein. We also apply this system to time-lapse FLIM of NAD(P)H autofluorescence in single live cells and report measurements on the change in the fluorescence decay profile following the application of a known metabolic inhibitor.

We describe an optical sectioning microscopy system with no moving parts based on a micro-structured stripe-array light emitting diode (LED). By projecting arbitrary line or grid patterns onto the object, we are able to implement a variety of optical sectioning microscopy techniques such as grid-projection structured illumination and line scanning confocal microscopy, switching from one imaging technique to another without modifying the microscope setup. The micro-structured LED and driver are detailed and depth discrimination capabilities are measured and calculated.

We present a novel fluorescence lifetime tomography system applied to a highly scattering autofluorescent phantom containing live cells expressing the fluorophore enhanced green fluorescent protein (EGFP). The fluorescence signal was excited using a fiber-laser-pumped supercontinuum source and detected using wide-field time gating imaging. To facilitate rapid 3D reconstruction of the fluorescence lifetime distribution, the time-resolved data were Fourier-transformed in time to give complex functions that formed a data set for the Fourier domain reconstruction. Initially the presence of an unspecified background autofluorescence signal impeded reconstruction of the lifetime distribution, but we show that this problem can be addressed using a simple iterative technique.

We demonstrate an optically sectioned fluorescence lifetime imaging microscope with a wide-field detector, using a convenient, continuously tunable (435-1150 nm) ultrafast source for fluorescence imaging applications that is derived from a visible supercontinuum generated in a microstructured fiber.

We report the development of a high-speed wide-field fluorescence-lifetime imaging (FLIM) system that provides fluorescence-lifetime images at rates of as many as 29 frames/s. A FLIM multiwell plate reader and a potentially portable FLIM endoscopic system operating at 355-nm excitation have been demonstrated.

Holographic optical coherence imaging is a full-frame variant of coherence-domain imaging. An optoelectronic semiconductor holographic film functions as a coherence filter placed before a conventional digital video camera that passes coherent (structure-bearing) light to the camera during holographic readout while preferentially rejecting scattered light. The data are acquired as a succession of en face images at increasing depth inside the sample in a fly-through acquisition. The samples of living tissue were rat osteogenic sarcoma multicellular tumor spheroids that were grown from a single osteoblast cell line in a bioreactor. Tumor spheroids are nearly spherical and have radial symmetry, presenting a simple geometry for analysis. The tumors investigated ranged in diameter from several hundred micrometers to over 1 mm. Holographic features from the tumors were observed in reflection to depths of 500-600 microm with a total tissue path length of approximately 14 mean free paths. The volumetric data from the tumor spheroids reveal heterogeneous structure, presumably caused by necrosis and microcalcifications characteristic of some human avascular tumors.

We have developed a wide-field time-resolved imaging system to image quantitatively both the fluorescence lifetime and the rotational correlation time of a fluorophore. Using a polarization-resolved imager, we simultaneously image orthogonal polarization components of the fluorescence emission onto a time-gated intensified CCD. We demonstrate imaging of solvent viscosity variations through the rotational correlation time of fluorescein in a multiwell plate and apply this technique to probe the microviscosity in live cells.

We have applied fluorescence lifetime imaging (FLIM) to the autofluorescence of different kinds of biological tissue in vitro, including animal tissue sections and knee joints as well as human teeth, obtaining two-dimensional maps with functional contrast. We find that fluorescence decay profiles of biological tissue are well described by the stretched exponential function (StrEF), which can represent the complex nature of tissue. The StrEF yields a continuous distribution of fluorescence lifetimes, which can be extracted with an inverse Laplace transformation, and additional information is provided by the width of the distribution. Our experimental results from FLIM microscopy in combination with the StrEF analysis indicate that this technique is ready for clinical deployment, including portability that is through the use of a compact picosecond diode laser as the excitation source. The results obtained with our FLIM endoscope successfully demonstrated the viability of this modality, though they need further optimization. We expect a custom-designed endoscope with optimized illumination and detection efficiencies to provide significantly improved performance.

We report a wide-field fluorescence lifetime imaging (FLIM) system that uses a blue picosecond pulsed diode laser as the excitation source. This represents a significant miniaturization and simplification compared with other time-domain FLIM instruments that should accelerate the development of clinical and real-world applications of FLIM. We have demonstrated this instrument in two configurations: a macroimaging setup applied to multiwell plate assays of chemically and biologically interesting fluorophores and a microscope system that has been applied to imaging of tissue sections. The importance of the adjustable repetition rate of this laser source is discussed with respect to noise reduction and precision in the lifetime determination, illustrating a further significant advantage over conventional mode-locked solid-state lasers.

We have developed an ABCD matrix that, for the first time to our knowledge, accurately describes the transformation of a Gaussian beam by a medium with transversely varying saturable gain. In contrast with the conventional ABCD matrix, the newly developed matrix is shown to be in excellent agreement with a full beam propagation code over a wide parameter range. Accurate treatment of transversely varying saturable gain in laser resonators is important for the optimization of end-pumped lasers, particularly for efficient diode-pumped solid-state and Kerr-lens mode-locked systems.

We report a novel whole-field three-dimensional fluorescence lifetime imaging microscope that incoporates multispectral imaging to provide five-dimensional (5-D) fluorescence microscopy. This instrument, which can acquire a 5-D data set in less than a minute, is based on potentially compact and inexpensive diode-pumped solid-state laser technology. We demonstrate that spectral discrimination as well as optical sectioning minimize artifacts in lifetime determination and illustrate how spectral discrimination improves the lifetime contrast of biological tissue.

Whole-field photorefractive holography can be combined with low-coherence interferometry for three-dimensional imaging and other applications, including imaging through turbid media, but the off-axis holographic recording geometry results in a limited field of view when light of low temporal coherence is used. We show that tilting the energy fronts with respect to the wave fronts by use of prisms can eliminate this problem and point out that this approach will be useful for many linear and nonlinear wave-mixing experiments.

We describe a novel three-dimensional fluorescence lifetime imaging microscope that exploits structured illumination to achieve whole-field sectioned fluorescence lifetime images with a spatial resolution of a few micrometers.

Due to an oversight during the revision process, one of the authors was not mentioned in this paper. The author list should read: R. Jones, M. Tziraki, D. Parsons Karavassilis, P. M. W. French, K. M. Kwolek, D. D. Nolte and M. R. Melloch.

We describe a novel whole-field fluorescence lifetime imaging system, based on a time-gated image intensifier and a solid-state laser oscillator-amplifier, that images lifetime differences of less than 10 ps. This system was successfully applied to discrimination between biological tissue constituents.

Customized photorefractive quantum-well devices have been developed for real-time video acquisition of coherence-gated, three-dimensional images in turbid media. Large-field-of-view holographic imaging with direct video capture is now possible. We have evaluated the role of intensity-limited device performance in Fourier-plane and image-plane holography in such devices and, using near-infrared light, have imaged through turbid phantoms of 13 mean free paths' scattering depth with 50-microm transverse and 60-microm depth resolution.

Fourteen new cw, visible laser transitions have been observed in Pr(3+):YLF, several of which have exhibited modest tunability. The (3)P(0) - (3)H(6) transition near 613 nm has been shown to have a tunable linewidth of ~1 nm, which, for the first time to our knowledge, has permitted the direct production of femtosecond pulses in the visible from a cw solid-state laser by Kerr-lens mode locking.

We have observed true self-starting Kerr-lens mode locking in two distinct solid-state laser systems operating at room temperature by optimizing the cavity geometry to maximize the amplitude modulation with respect to the intracavity power variation. Pulses of 15 ps have been obtained from a Pr(3+):YLF laser system operating at 607 nm, and 53-fs pulses have been obtained from Cr(4+):YAG at 1.54 microm.

An experimental and theoretical investigation of the temporal spread of an ultrashort light pulse on transmission through a highly scattering medium has been made. For the strongly diffuse light, the transmitted pulse may be described by a universal function whose duration can be directly related to the width of the sample. For sufficiently scattering samples, experimental data and the diffusion approximation indicate that the output pulse duration scales with the square root of the sample width.

A depth-resolved near-infrared imaging system has been demonstrated for recording three-dimensional images of objects embedded in diffuse media. Time-gated holographic imaging employing rhodium-doped barium titanate as the recording medium is used to acquire whole depth-resolved two-dimensional images in 1 s. Millimeter depth resolution has been achieved with a transverse resolution of ~ 30 microm.

A tunable femtosecond solid-state amplifier system that uses only 3 W of 488-nm argon-ion pump power has been demonstrated to deliver microjoule pulses at repetition rates up to 20 kHz, with a maximum pulse energy of 14 mu;J obtained at 5 kHz. An all-solid-state, tunable, diode-pumped Cr:LiSrAlF(6) regenerative amplifier has been demonstrated, for the first time to our knowledge, that amplifies femtosecond pulses to energies exceeding 1 mu;mJ at up to a 16-kHz repetition rate.

We report the passive mode locking of a Cr(4+):YAG laser by use of a moving mirror and the generation of pulses as short as 70 fs by use of Kerr-lens mode locking. The intracavity dispersion has been measured, and the laser performance has been related to water absorption lines.

A diode-pumped mode-locked Cr:LiSAF laser is demonstrated for what is to our knowledge the first time. Active mode locking, with an acousto-optic modulator, and resonant passive mode locking, with a multiple-quantum-well absorber in an external cavity, have both yielded cw trains of picosecond pulses.

A Cr:LiSrAIF(6) laser has been mode locked by using a multiple-quantum-well (MQW) absorber. With the MQW absorber inside the laser cavity, Kerr lens mode locking is initiated, yielding transform-limited pulses as short as 93 fs. Pulses of 500-fs duration have also been produced by using resonant passive mode locking with the MQW absorber in an external cavity.

A cw room-temperature Cr(4+):YAG laser, tuning from 1.37 to 1.51 microm, is described. Mode locking of this novel laser is reported for what is to our knowledge the first time.