Search

Experimental results are presented for 24 thermal expansion experiments performed on 5 welded specimens of the Paintbrush tuff recovered from borehole USW SD-12 at Yucca Mountain, Nevada. The thermal expansion experiments were performed at constant confining pressures between 1 and 30 MPa. On three specimens, the highest confining pressure measurements were performed first to inhibit thermally induced damage which might occur at lower confining pressures. At each confining pressure two complete thermal cycles were performed. The specimens were heated (to a nominal temperature of 250 C) and cooled at the nominal rate of 0.319 C per minute. The change in specimen length as a function of temperature was measured with two linear variable displacement transducers mounted on endcaps secured to the specimen. The strain increases with increasing temperature and the strain vs temperature curves are concave upward. On cooling, there is hysteresis at the higher temperatures at all confining pressures. The first heating/cooling cycle is anomalous; hysteresis is pronounced, and a permanent shortening of the specimen is observed at the termination of the cycle. The magnitude of the effect was similar for all five specimens regardless of whether the first cycle was carried out at the highest or lowest confining pressure. For subsequent cycles at all confining pressures, no permanent strain develops, and the strain versus temperature curves re very similar. The mean coefficients of thermal expansion ({alpha}) range from 7.9 to 10.8{sup {minus}6} C{sup {minus}1} at temperatures below 100 C, to 14.2 to 20.6 x 10{sup {minus}6} C{sup {minus}1} at temperatures approaching 250 C. The effect of confining pressure on thermal expansion is small. For temperatures above 175 C, the mean coefficients of thermal expansion decreases by 10--12% as the pressure increases from 1 to 30 MPa.

Experimental results are presented for bulk and mechanical properties measurements on specimens of the Paintbrush tuff recovered from the USW NRG-6 and USW NRG-7/7A borehole at Yucca Mountain, Nevada. Measurements have been performed on five thermal/mechanical units: TCw, PTn, TSw2, and TSw3. The following bulk properties are reported for each specimen: dry bulk density, saturated bulk density, average grain density and porosity. Confined compression to failure tests were performed on selected specimens recovered from the boreholes at confining pressures of 5 and 10 MPa. In addition, compressional and shear wave velocities were measured on the specimens prior to testing. Measurements were conducted under drained conditions at room temperature on nominally water saturated specimens. The nominal strain rate for the experiments was 10{sup -5} s{sup -1}.

Experimental results are presented for seven creep experiments on welded specimens of the Paintbrush tuff recovered from borehole USW NRG-7/7A at Yucca Mountain, Nevada. The measurements were performed at differential stresses of 40, 70, 100, and 130 MPa. The confining pressure and temperature for each of the experiments was 10 MPa and 225 {degrees}C respectively. All of the specimens were tested drained, in a room dry condition. All of the experiments were terminated prior to failure. The duration of the experiments range from 2.6 x 10{sup 6} seconds to 5.9 x 10{sup 6} seconds. Creep strain is observed for those specimens tested at a stress difference. The strain rate is not constant. A primary creep stage is observed. Secondary creep does not exhibit a constant strain rate, but decreases with increasing time.

Experimental results are presented for bulk and mechanical properties measurements on specimens of the Paintbrush tuff recovered from boreholes UE25 NRG-4 and -5, at Yucca Mountain, Nevada. Measurements have been performed on three thermal/mechanical units, PTn, TSwl, and TSw2. On each specimen the following bulk properties have been reported: dry bulk density, saturated bulk density, average grain density, and porosity. Unconfined compression to failure, confined compression to failure, and indirect tensile strength tests were performed on selected specimens recovered from the boreholes. In addition, compressional and shear wave velocities were measured on specimens designated for unconfined compression and confined compression experiments. Measurements were conducted at room temperature on nominally water-saturated specimens. The nominal rate for the fracture experiments was 10{sup -5}s{sup -1}.

An integral part of the licensing procedure for the potential nuclear waste repository at Yucca Mountain, Nevada, involves characterization of the in situ rheology for the design and construction of the facility and the emplacement of canisters containing radioactive waste. The data used to model the thermal and mechanical behavior of the repository and surrounding lithologies include dry and saturated bulk densities, average grain density, porosity, compressional and shear wave velocities, elastic moduli, and compressional and tensional fracture strengths. In this study, a suite of experiments was performed on cores recovered from boreholes UE25 NRG-2, 2A, 2B, and 3 drilled in support of the Exploratory Studies Facility (ESF) at Yucca Mountain. The holes penetrated the Timber Mountain tuff and two thermal/mechanical units of the Paintbrush tuff. The thermal/mechanical stratigraphy was defined by Ortiz to group rock horizons of similar properties for the purpose of simplifying modeling efforts. The relationship between the geologic stratigraphy and the thermal/mechanical stratigraphy for each borehole is presented. The tuff samples in this study have a wide range of welding characteristics (usually reflected in sample porosity), and a smaller range of mineralogy and petrology characteristics. Generally, the samples are silicic, ash-fall tuffs that exhibit large variability in their elastic and strength properties.

A laboratory investigation has been carried out to determine the effects of elevated temperature and stress on the creep deformation of welded tuffs recovered from Busted Butte in the vicinity of Yucca Mountain, Nevada. Water saturated specimens of tuff from thermal/mechanical unit TSw2 were tested in creep at a confining pressure of 5.0 MPa, a pore pressure of 4.5 MPa, and temperatures of 25 and 250 C. At each stress level the load was held constant for a minimum of 2.5 {times} 10{sup 5} seconds and for as long as 1.8 {times} 10{sup 6} seconds. One specimen was tested at a single stress of 80 MPa and a temperature of 250 C. The sample failed after a short time. Subsequent experiments were initiated with an initial differential stress of 50 or 60 MPa; the stress was then increased in 10 MPa increments until failure. The data showed that creep deformation occurred in the form of time-dependent axial and radial strains, particularly beyond 90% of the unconfined, quasi-static fracture strength. There was little dilatancy associated with the deformation of the welded tuff at stresses below 90% of the fracture strength. Insufficient data have been collected in this preliminary study to determine the relationship between temperature, stress, creep deformation to failure, and total failure time at a fixed creep stress.

An integral part of the licensing procedure for the potential nuclear waste repository at Yucca Mountain, Nevada, involves prediction of the in situ rheology for the design and construction of the facility and the emplacement of canisters containing radioactive waste. The data used to model the thermal and mechanical behavior of the repository and surrounding lithologies include dry and saturated bulk densities, average grain density, porosity, compressional and shear wave velocities, elastic moduli, and compressional and tensional fracture strengths. In this study, a suite of experiments was performed on cores recovered from the USW NRG-717A borehole drilled in support of the Exploratory Studies Facility (ESF) at Yucca Mountain. USW NRG-7/7A was drilled to a depth of 1,513.4 feet through five thermal/mechanical units of Paintbrush tuff and terminating in the tuffaceous beds of the Calico IEUS. The thermal/mechanical stratigraphy was defined by Orfiz et al. to group rock horizons of similar properties for the purpose of simplifying modeling efforts. The relationship between the geologic stratigraphy and the thermal/mechanical stratigraphy is presented. The tuff samples in this study have a wide range of welding characteristics, and a smaller range of mineralogy and petrology characteristics. Generally, the samples are silicic, ash-fall tuffs that exhibit large variability in their elastic and strength properties.

Lateral and vertical variabilities in the bulk and mechanical properties of silicic volcanic tuff at the potential nuclear waste repository site in Yucca Mountain, NV have been evaluated. Laboratory measurements have been performed on tuff specimens recovered from boreholes located to support the design of the Exploratory Studies Facility/North Ramp. The data include dry and saturated bulk densities, average grain density, porosity, compressional and shear wave velocities, elastic moduli, and compressional and tensional fracture strengths. Data from eight boreholes aligned in a northwest-southeast direction have been collected under the required quality assurance program. Three boreholes have penetrated the potential repository horizon. The information collected provides for an accurate appraisal of the variability of rock properties in the vicinity of the boreholes. As expected, there is substantial variability in the bulk and mechanical properties of the tuff with depth (lithology). This is due to variations in gross characteristics of the tuffs (e.g., cooling units, mode of deposition, etc.), as well as smaller scale features (welding, porosity, and internal structures) that have developed as a result of depositional and post-depositional mechanisms. An evaluation of the lateral variability in bulk and mechanical properties is somewhat limited, at this time, due to a lack of borehole control to the north and south (parallel to the depositional flow direction). Initial observations indicate that there is minimal lateral variability within lithologic units. There are observable differences however, that can be related to variability in specific properties (e.g., porosity, and internal structures).

Experimental results are presented for bulk and mechanical properties measurements on specimens of the Paintbrush tuff recovered from borehole USW NRG-6 at Yucca Mountain, Nevada. Measurements have been performed on four thermal/mechanical units, TCw, PTn, TSw1 and TSw2. On each specimen the following bulk properties have been reported: dry bulk density, saturated bulk density, average grain density, and porosity. Unconfined compression to failure, confined compression to failure, and indirect tensile strength tests were performed on selected specimens recovered from the borehole. In addition, compressional and shear wave velocities were measured on specimens designated for unconfined compression and confined compression experiments. Measurements were conducted at room temperature on nominally water saturated specimens; however, some specimens of PTn were tested in a room dry condition. The nominal strain rate for the fracture experiments was 10{sup -5} s {sup -1}.

Laboratory experiments were performed to measure the effect of frequency, water-saturation, and strain amplitude on Young`s modulus and seismic wave attenuation on rock cores recovered on or near the site of a potential nuclear waste repository at Yucca Mountain, Nevada. The purpose of this investigation is to perform the measurements using four techniques: cyclic loading, waveform inversion, resonant bar, and ultrasonic velocity. The measurements ranged in frequency between 10{sup {minus}2} and 10{sup 6} Hz. For the dry specimens Young`s modulus and attenuation were independent of frequency; that is, all four techniques yielded nearly the same values for modulus and attenuation. For saturated specimens, a frequency dependence for both Young`s modulus and attenuation was observed. In general, saturation reduced Young`s modulus and increased seismic wave attenuation. The effect of strain amplitude on Young`s modulus and attenuation was measured using the cyclic loading technique at a frequency of 10{sup {minus}1} Hz. The effect of strain amplitude in all cases was small. For some rocks, such as the potential repository horizon of the Topopah Spring Member tuff (TSw2), the effect of strain amplitude on both attenuation and modulus was minimal.

An integral part of the licensing procedure for the potential nuclear waste repository at Yucca Mountain, Nevada involves accurate prediction of the in situ rheology for design and construction of the facility and emplacement of the canisters containing radioactive waste. The data required as input to successful thermal and mechanical models of the behavior of the repository and surrounding lithologies include bulk density, grain density, porosity, compressional and shear wave velocities, elastic moduli, and compressional and tensile strengths. In this study a suite of experiments was performed on cores recovered from the USW-NRG-6 borehole drilled to support the Exploratory Studies Facility (ESF) at Yucca Mountain. USW-NRG-6 was drilled to a depth of 1100 feet through four thermal/mechanical units of Paintbrush tuff. A large data set has been collected on specimens recovered from borehole USW-NRG-6. Analysis of the results of these experiments showed that there is a correlation between fracture strength, Young`s modulus, compressional wave velocity and porosity. Additional scaling laws relating; static Young`s modulus and compressional wave velocity; and fracture strength and compressional wave velocity are promising. Since there are no other distinct differences in material properties, the scatter that is present at each fixed porosity suggests that the differences in the observed property can be related to the pore structure of the specimen. Image analysis of CT scans performed on each test specimen are currently underway to seek additional empirical relations to aid in refining the correlations between static and dynamic properties of tuff.

Samples of tuffaceous rock were studied as part of the site characterization for a potential nuclear waste repository at Yucca Mountain in southern Nevada. These efforts were scoping in nature, and their results, along with those of other investigations, are being used to develop suitable procedures for determining bulk properties of tuffaceous rock in support of thermal and mechanical properties evaluations. Comparisons were made between various sample preparation, handling, and measurement techniques for both zeolitized and nonzeolitized tuff in order to assess their effects on bulk property determinations. Laboratory tests included extensive drying regimes to evaluate dehydration behavior, the acquisition of data derived from both gas and water pycnometers to compare their suitability in determining grain densities, a comparison of particle size effects, and a set of experiments to evaluate whole core saturation methods. The results affirm the added complexity of these types of measurements where there is a zeolite component in the sample mineralogy. Absolute values for the bulk properties of zeolitized tuff are immeasurable due to the complex nature of their dehydration behavior. However, the results of the techniques that were investigated provide a basis for the development of preferred, consistent methods for determining the grain density, dry and saturated bulk densities, and porosity of tuffaceous rock, including zeolitic tuff in support of thermal and mechanical properties evaluations.

Experiment results are presented for unconfined compressive strength and elastic moduli of tuffaceous rocks from Busted Butte near Yucca Mountain, Nevada. The data have been compiled for the Yucca Mountain Site Characterization Project Site and Engineering Properties Data Base. Experiments were conducted on water-saturated specimens of the potential nuclear waste repository horizon Topopah Spring Member tuff (thermal/mechanical unit TSw2). The influence of strain rate on mechanical properties of the tuff was examined by loading six specimens in uniaxial compression at a strain rate of 10{sup {minus}9} s{sup {minus}1}. The experiments performed under ambient pressure and temperature conditions and conformed to Technical Procedure 91, titled ``Unconfined Compression Experiments at 22{degrees}C and a Strain Rate of 10{sup {minus}9} s{sup {minus}1}.`` The mean and standard deviation values of ultimate strength, Young`s modulus and Poisson`s ratio determined from these experiments are 85.4{plus_minus}21.7 MPa, 33.9{plus_minus}4.6 GPa, and 0.09{plus_minus}0.07, respectively.

Mechanical properties of the tuffaceous rocks within Yucca Mountain are needed for near and far-field modeling of the potential nuclear waste repository. If the mechanical properties are significantly anisotropic (i.e., direction-dependent), a more complex model is required. Relevant data from tuffs tested in earlier studies indicate that elastic and strength properties are anisotropic. This scoping study confirms the elastic anisotropy and concludes some tuffs are transversely isotropic. An approach for sampling and testing the rock to determine the magnitude of the anisotropy is proposed.

The effects of loading frequency, strain amplitude, and saturation on elastic moduli and attenuation have been measured in samples of the Topopah Spring Member welded tuff. Four different laboratory techniques have been used to determine Young`s modulus and extensional wave attenuation at frequencies ranging from 10{sup {minus}2} to 10{sup 6} Hz. The results are compared with data acquired for Sierra White granite under the same conditions. The modulus and attenuation in room dry samples remain relatively constant over frequency. Frequency dependent attenuation and modulus dispersion are observed in the saturated samples and are attributed to fluid flow and sample size. The properties of tuff were independent of strain amplitude in room dry and saturated conditions.

Licensing of the potential nuclear-waste repository at Yucca Mountain by the Nuclear Regulatory Commission would require, among other things, demonstrations of the long term usability of the underground facilities. Such a demonstration involves analysis of the mechanical response of the rock to the presence of underground openings and heat-producing waste, which in turn requires data on the mechanical properties of the rock. This document describes the experimental results from a scoping study which led to the development of procedures for performing quality-affecting rock-mechanics experiments on intact rock. The future experiments performed with these procedures will produce information on the time-dependent deformation of welded tuff and represent one aspect of the overall effort to characterize the rheology of the rock mass. 3 refs., 42 figs., 6 tabs.