Search

Abstract Take a thin cylindrical shell and twist it; it will buckle immediately. Such unavoidable torsional buckling can lead to systemic failure, for example by disrupting the blood flow through arteries. In this study, we prevent this torsional buckling instability using a combination of auxeticity and orthotropy in cylindrical metamaterial shells with a holey pattern. When the principal axes of the orthotropic meta-shell are relatively aligned with that of the compressive component of the applied stress during twisting, the meta-shell uniformly shrinks in the radial direction as a result of a local buckling instability. This shrinkage coincides with a softening-stiffening transition that leads to ordered stacking of unit cells along the compressive component of the applied stress. These transitions due to local instabilities circumvent the usual torsional instability even under a large twist angle. This study highlights the potential of tailoring anisotropy and programming instabilities in metamaterials, with potential applications in designing mechanical elements for soft robotics, biomechanics or fluidics. As an example of such applications, we demonstrate soft torsional compressor for generating pulsatile flows through a torsion release mechanism.

Abstract The coefficient of static friction between solids normally increases with the time they have remained in static contact before the measurement. This phenomenon, known as frictional aging, is at the origin of the difference between static and dynamic friction coefficients but has remained difficult to understand. It is usually attributed to a slow expansion of the area of atomic contact as the interface changes under pressure. This is however challenging to quantify as surfaces have roughness at all length scales. In addition, friction is not always proportional to the contact area. Here we show that the normalized stress relaxation of the surface asperities during frictional contact with a hard substrate is the same as that of the bulk material, regardless of the asperities’ size or degree of compression. This result enables us to predict the frictional aging of rough interfaces based on the bulk material properties of two typical polymers: polypropylene and polytetrafluoroethylene.

Abstract Nebulization of mRNA therapeutics can be used to directly target the respiratory tract. A promising prospect is that mucosal administration of lipid nanoparticle (LNP)-based mRNA vaccines may lead to a more efficient protection against respiratory viruses. However, the nebulization process can rupture the LNP vehicles and degrade the mRNA molecules inside. Here we present a novel nebulization method able to preserve substantially the integrity of vaccines, as tested with two SARS-CoV-2 mRNA vaccines. We compare the new method with well-known nebulization methods used for medical respiratory applications. We find that a lower energy level in generating LNP droplets using the new nebulization method helps safeguard the integrity of the LNP and vaccine. By comparing nebulization techniques with different energy dissipation levels we find that LNPs and mRNAs can be kept largely intact if the energy dissipation remains below a threshold value, for LNP integrity 5–10 J/g and for mRNA integrity 10–20 J/g for both vaccines.

Crystalline solids are commonly associated with their hard and faceted nature. Here, the authors report the transition from hard to soft and deformable, observed in the gradual dissolution of salt crystals that harbor water in their crystalline framework.

Abstract Environmentally sensitive molecular rotors are widely used to probe the local molecular environment in e.g. polymer solutions, polymer glasses, and biological systems. These applications make it important to understand its fluorescence properties in the vicinity of a solid surface, since fluorescence microscopy generically employs cover slides, and measurements are often done in its immediate vicinity. Here, we use a confocal microscope to investigate the fluorescence of (4-daspi) in glycerol/water solutions close to the interface using hydrophilic or hydrophobic cover slips. Despite the dye’s high solubility in water, the observed lengthening of the fluorescence lifetime close to the hydrophobic surface, implies a surprising affinity of the dye with the surface. Because the homogeneous solution and the refractive index mismatch reduces the optical sectioning power of the microscope, we quantify the affinity with the help of a simple model of the signal vs. depth of focus, exhibiting surface and bulk contributions. The model reduces artefacts due to refractive index mismatch, as supported by Monte Carlo ray tracing simulations.

Abstract The charging of poorly conducting liquids due to flows is a well-known phenomenon, yet the precise charging mechanism is not fully understood. This is especially relevant for sprays, where the spray plume dynamics and maximum distance travelled of a spray dramatically changes for different levels of charging: charging of the droplets makes them repel, thereby preventing drop coalescence and altering the shape of the spray plume. As the charging depends on many factors including the flow and the interactions between the liquid and the nozzle, many models and scaling laws exist in the literature. In this work we focus on perhaps the simplest flow regime, laminar jets created by ultra short channels, and quantify the charging as a function of the different parameters. We present a simple model that collapses all the data for over 4 orders of magnitude difference in streaming currents for various nozzle sizes, flow velocities and surface treatments. We further show that the charging polarity can even be reversed by applying an oppositely charged coating to the nozzle, an important step for any application.

What drives the mouthfeel of ’thickness’? When is a soup too ’thick’? Here, authors measure the rheology of liquid soups and show their subjectively perceived ’thickness’ can be directly associated to their non-Newtonian rheology.

Fragmentation of breaking glass as a brittle solid is a problem of equal practical and theoretical importance. Kooij et al. demonstrate that the fragment size distribution can surprisingly be both, either power-law or exponential, depending on how a particular specimen is broken.

Polyethers are ubiquitous in our daily lives, and display counterintuitive solubilities in water. Here the authors show, by ultrafast spectroscopies and computations, that solubility does not depend on steric factors but on the interaction of water molecules with the polymer’s charge distribution

Ice sublimation is a common, yet little-studied, heat and mass transfer problem with climatic and industrial implications. Here, the authors show that the sublimation of ice crystals is purely diffusive and is unaffected by the underlying crystalline lattice.

The cytoplasm’s crowdedness leads one to expect that cell water is different from bulk water. By measuring the rotational motion of water molecules in living cells, Tros et al. find that apart from a small fraction of water solvating biomolecules, cell water has the same dynamics as bulk water.

Principles underlying crumpling of one-dimensional objects may be relevant to both biomolecular processes and to design of mechanical devices. By compacting various wires under rigid confinement and modelling observed geometric features, the authors show how friction, plasticity and torsion enhance disorder and lead to a transition from coiled to folded geometries.