Search

The optical remote sensors carried by the Jilin-1 KF02 series satellites have an imaging resolution better than 0.5 m and a width of 150 km. There are radiometric problems, such as stripe noise, vignetting, and inter-slice chromatic aberration, in their raw images. In this paper, a relative radiometric correction method based on temperature normalization is proposed for the response characteristics of sensors and the structural characteristics of optical splicing of Jilin-1 KF02 series satellites cameras. Firstly, a model of temperature effect on sensor output is established to correct the variation of sensor response output digital number (DN) caused by temperature variation during imaging process, and the image is normalized to a uniform temperature reference. Then, the horizontal stripe noise of the image is eliminated by using the sensor scan line and dark pixel information, and the vertical stripe noise of the image is eliminated by using the method of on-orbit histogram statistics. Finally, the method of superposition compensation is used to correct the vignetting area at the edge of the image due to the lack of energy information received by the sensor so as to ensure the consistency of the image in color and image quality. The proposed method is verified by Jilin-1 KF02A on-orbit images. Experimental results show that the image response is uniform, the color is consistent, the average Streak Metrics (SM) is better than 0.1%, Root-Mean-Square Deviation of the Mean Line (RA) and Generalized Noise (GN) are better than 2%, Relative Average Spectral Error (RASE) and Relative Average Spectral Error (ERGAS) are greatly improved, which are better than 5% and 13, respectively, and the relative radiation quality is obviously improved after relative radiation correction.

With increasingly serious environmental pollution problems, the development of efficient photocatalytic materials has become a hotspot in current research. This study focused on phosphorus-doped carbon nitride/titanium dioxide (PCT) Z-type heterojunctions, aiming to deeply investigate their photocatalytic degradation and photosensitive antimicrobial properties. A PCT Z-type heterojunction was successfully fabricated using melamine phosphate, cyanuric acid, and titanium dioxide. The structure, morphology, and optical properties of PCT Z-type heterojunctions were explored by FTIR, XRD, XPS, BET, SEM, UV-Vis DRS, TEM, EIS, and PL. A comprehensive and in-depth analysis of the structure, morphology, and optical properties of PCT Z-type heterojunctions was carried out. The photocatalytic degradation experiments revealed that PC3T Z-type heterojunctions exhibited an excellent degradation capability for methylene blue (MB) under visible light. The effect of PC3T on the adsorption–photocatalytic degradation of MB is more than 1.5 times that of a single titanium dioxide and P-doped carbon nitride. In the photosensitive antimicrobial performance study, PC3T reduced the survival rate of E. coli to 7%, after 120 min. Through free radical trapping experiments, it was shown that the hydroxyl radicals and superoxide radicals exerted an influence on the photocatalytic process. This study offers new ideas and approaches to address environmental pollution problems and holds significant theoretical and applied value.

Photocatalysis is one of the most effective ways to solve environmental problems by solving pollutants. This article designed and prepared a conjugated system of 2,4,6-triaminopyrimidine-g-C3N4 (TAP-CN) to modify ZnO NWs. We systematically studied the photocatalytic performance of ZnO NWs modified with different ratios of TAP-CN. The results showed that 9 wt% TAP-CN-30/ZnO NWs had the best degradation effect on Rhodamine B dye. The degradation rate was 99.36% in 80 min. The excellent degradation performance was attributed to the TAP-CN conjugated system promoting photo-generated charge transfer. This work provided guidance for designing efficient composite catalysts for application in other renewable energy fields.

Organic pollutants were one of the main sources of environmental pollutants. The degradation of organic pollutants through photocatalytic technology was one of the effective solutions. By preparing zinc oxide(ZnO) nanowires modified with sodium-doped conjugated 2,4,6-triaminopyrimidin-g-C3N4 (NaTCN) heterojunction (ZnO/NaTCN), the photocatalytic performance of NaTCN modified with different ratios of ZnO was systematically studied. The photocatalytic performance was studied through the degradation performance of methyl blue (MB) dye. The results showed that 22.5 wt% ZnO/NaTCN had the best degradation effect on MB dye. The degradation rate of MB reached 98.54% in 70 min. After three cycles, it shows good cycling stability (degradation rate is 96.99%) for dye degradation. It was found that there are two types of active species: ·OH and h+, of which h+ is the main active species produced by photocatalytic degradation of dyes. The excellent degradation performance was attributed to the fact that ZnO facilitated the extraction and transport of photogenerated carriers. The doping of sodium facilitated charge transfer. The NaTCN conjugated system promoted the extraction and transfer of photogenerated carriers. It provided guidance for designing efficient composite catalysts for use in other renewable energy fields.

The development of a stable and highly active photocatalyst has garnered significant attention in the field of wastewater treatment. In this study, a novel technique involving a facile stirring method was devised to fabricate an array of g-C3N4/ZnO nanowire (ZnO NW) composites. Through the introduction of g-C3N4 to augment the generation of electron-hole pairs upon exposure to light, the catalytic efficacy of these composites was found to surpass that of the pristine ZnO NWs when subjected to simulated sunlight. The photocatalytic performance of a 20 mg·L−1 methylene blue solution was found to be highest when the doping rate was 25 wt%, resulting in a degradation rate of 99.1% after 60 min. The remarkable enhancement in catalytic efficiency can be ascribed to the emergence of a captivating hetero-junction at the interface of g-C3N4 and ZnO NWs, characterized by a harmoniously aligned band structure. This alluring arrangement effectively curtailed charge carrier recombination, amplified light absorption, and augmented the distinct surface area, culminating in a notable boost to the photocatalytic prowess. These findings suggest that the strategic engineering of g-C3N4/ZnO NW heterostructures holds tremendous promise as a pioneering avenue for enhancing the efficacy of wastewater treatment methodologies.

Hydrogels are materials consisting of a network of hydrophilic polymers. Due to their good biocompatibility and hydrophilicity, they are widely used in biomedicine, food safety, environmental protection, agriculture, and other fields. This paper summarizes the typical complex materials of photocatalysts, photosensitizers, and hydrogels, as week as their antibacterial activities and the basic mechanisms of photothermal and photodynamic effects. In addition, the application of hydrogel-based photoresponsive materials in microbial inactivation is discussed, including the challenges faced in their application. The advantages of photosensitive antibacterial complex hydrogels are highlighted, and their application and research progress in various fields are introduced in detail.

Environmental pollution, especially water pollution, is becoming increasingly serious. Organic dyes are one type of the harmful pollutants that pollute groundwater and destroy ecosystems. In this work, a series of graphitic carbon nitride (g-C3N4)/ZnO photocatalysts were facilely synthesized through a grinding method using ZnO nanoparticles and g-C3N4 as the starting materials. According to the results, the photocatalytic performance of 10 wt.% CN-200/Z-500 (CN-200, which g-C3N4 was 200 kGy, referred to the irradiation metering. Z-500, which ZnO was 500 °C, referred to the calcination temperature) with the CN-200 exposed to electron beam radiation was better than those of either Z-500 or CN-200 alone. This material displayed a 98.9% degradation rate of MB (20 mg/L) in 120 min. The improvement of the photocatalytic performance of the 10 wt.% CN-200/Z-500 composite material was caused by the improvement of the separation efficiency of photoinduced electron–hole pairs, which was, in turn, due to the formation of heterojunctions between CN-200 and Z-500 interfaces. Thus, this study proposes the application of electron-beam irradiation technology for the modification of photocatalytic materials and the improvement of photocatalytic performance.

Materials with excellent biocompatibility and targeting can be widely used in the biomedical field. Hydrogels are an excellent biomedical material, which are similar to living tissue and cannot affect the metabolic process of living organisms. Moreover, the three-dimensional network structure of hydrogel is conducive to the storage and slow release of drugs. Compared to the traditional hydrogel preparation technologies, ionizing radiation technology has high efficiency, is green, and has environmental protection. This technology can easily adjust mechanical properties, swelling, and so on. This review provides a classification of hydrogels and different preparation methods and highlights the advantages of ionizing radiation technology in smart hydrogels used for biomedical applications.

Over time, difficulties have been encountered in detecting potential fingerprints. In this study, an Ag/CMCS/PVA(ACP) hydrogel film was developed for fingerprint development by electron beam radiation method. The chemical bond, thermostability, chemical components, microstructure, and micromorphology of the CMCS/PVA composite hydrogel film were characterized by FT-IR, TG, XRD, and SEM, respectively. Swelling behaviors and mechanical performance of the CMCS/PVA composite hydrogel were also investigated at different irradiation doses, pH, media, and NaCl contents to obtain the optimum preparation conditions. Through experimental exploration, we found that the fingerprints appeared more obvious when the irradiated prepared ACP hydrogel film was sprayed with 0.6 mg/mL of Ag+ and the excitation wavelength was about 254 nm with UV lamp irradiation for 20 min. The cytotoxicity the CMCS/PVA composite hydrogel on mouse skin fibroblasts L929 cells was also studied, confirming its biological security. Sweat latent fingerprint manifestation has important scientific significance with respect to the development of new processes and functional materials in the field of fingerprint manifestation, enriching and complementing the application of composite hydrogels.

With the development of science and technology, photocatalytic technology is of great interest. Nanosized photocatalysts are easy to agglomerate in an aqueous solution, which is unfavorable for recycling. Therefore, hydrogel-based photocatalytic composites were born. Compared with other photocatalytic carriers, hydrogels have a three-dimensional network structure, high water absorption, and a controllable shape. Meanwhile, the high permeability of these composites is an effective way to promote photocatalysis technology by inhibiting nanoparticle photo corrosion, while significantly ensuring the catalytic activity of the photocatalysts. With the growing energy crisis and limited reserves of traditional energy sources such as oil, the attention of researchers was drawn to natural polymers. Like almost all abundant natural polymer compounds in the world, cellulose has the advantages of non-toxicity, degradability, and biocompatibility. It is used as a class of reproducible crude material for the preparation of hydrogel photocatalytic composites. The network structure and high hydroxyl active sites of cellulose-based hydrogels improve the adsorption performance of catalysts and avoid nanoparticle collisions, indirectly enhancing their photocatalytic performance. In this paper, we sum up the current research progress of cellulose-based hydrogels. After briefly discussing the properties and preparation methods of cellulose and its descendant hydrogels, we explore the effects of hydrogels on photocatalytic properties. Next, the cellulose-based hydrogel photocatalytic composites are classified according to the type of catalyst, and the research progress in different fields is reviewed. Finally, the challenges they will face are summarized, and the development trends are prospected.

The problem of rock mechanics and engineering is an old and new subject encountered by human beings in their struggle with nature for survival and development [...]

Research on underground coal mines has primarily focused on the stability of roadways. Mining activities lead to significant damage to the surrounding rocks and also degrade the support to the roadways. Considering the 21309 roadway of the Huojitu coal mine as a case study, this work comprehensively analyzed the characteristics of the surrounding rock using three methods: theoretical calculations, FLAC3D numerical modeling, and field observations. The results indicate that, under the influence of secondary mining, the failure range and stress concentration degree of the surrounding rock are considerably higher than those under the influence of primary mining. In this case, the maximum damage range in the surrounding rock can reach 1.8 m, the maximum principal stress can reach 19.82 MPa, and the ratio of the maximum principal stress to the minimum principal stress can reach 1.95. According to the results, the previous support design for roadways was optimized and applied in the field. Field monitoring revealed that the roadway deformation was effectively controlled, and the optimized support design was safe and reliable. This study is expected to serve as a reference for support designs or optimization under similar geological conditions.

Aiming at the large deformation instability problem caused by the excavation unloading of a coal roadway in deep-buried slowly inclined jointed rock mass, the geomechanical parameters and deformation failure characteristics of an engineering geomechanical model were investigated. The in-situ stress state of the model was measured with the stress relief method. The geological and mechanical properties of roadway surrounding rock were described. The surrounding rock structure was revealed with the electron microscopy scanning method, micro-fractures and randomly distributed joints highly developed in roadway surrounding rock. Field investigation and monitoring indicated the cross-section of roadway surrounding rock shrank continuously and the deformation distribution was obviously asymmetric. Shotcrete spalling and cable broken failures frequently occurred in the middle and ride side of roof and right rib. Based on the geomechanical conditions of the coal roadway, a discrete element numerical model of coal roadway in gently inclined jointed rock mass was established. The parameters of rock mass in the numerical model were calibrated. The model ran in unsupported condition to restore the evolution process of stress, crack propagation and deformation in roadway surrounding rock due to gradual deviatoric stress release caused by excavation. On this basis, the space-time evolution characteristics and law of stress, crack propagation and deformation were obtained and then the asymmetric large fragmentation and dilatation deformation failure mechanism of roadway surrounding rock in deep-buried slowly inclined jointed rock mass was revealed. The failure reasons of the support structure were analyzed, and the relevant support principles were proposed. The research results can provide scientific references for the stability control of roadways excavated in jointed rock mass.

Verticillium wilt is threatening cotton productivity globally. This disease is caused by soil-borne Verticillium dahliae which directly infects cotton roots, and exclusively colonizes and occludes xylem vessels, finally resulting in necrosis, defoliation, and most severely, plant death. For the first time, iTRAQ (isobaric tags for relative and absolute quantification) was applied to screen the differentially expressed proteins of Gossypium thurberi inoculated with V. dahliae. A total of 6533 proteins were identified from the roots of G. thurberi after inoculation with V. dahliae, and 396 showed up- and 279 down-regulated in comparison to a mock-inoculated roots. Of these identified proteins, the main functional groups were those involved in cell wall organization and reinforcement, disease-resistant chemicals of secondary metabolism, phytohormone signaling, pathogenesis-related proteins, and disease-resistant proteins. Physiological and biochemical analysis showed that peroxidase activity, which promotes the biosynthesis and accumulation of lignin, was induced early in the hypocotyl after inoculation with V. dahliae. Similarly, salicylic acid also accumulated significantly in hypocotyl of the seedlings after inoculation. These findings provide an important knowledge of the molecular events and regulatory networks occurring during G. thurberi-V. dahliae interaction, which may provide a foundation for breeding disease-resistance in cotton.

In order to modify the porous interfacial transition zone (ITZ) microstructure of concrete more efficiently, a method of coating aggregate surfaces by using several nanoparticles was evaluated in this study. The compressive strength, chloride penetration of sound, and pre-loading samples were assessed in relation to the type of coating materials used (slag, nano-CaCO3, and nano-SiO2) and the designed coating thickness (5, 10, and 15 μm). The ITZ microstructure was quantitatively determined via Backscattered electron (BSE) image analysis. Results showed that the overall performance of concrete is highly dependent on the coating materials and the designed coating thickness. Increasing the coating thickness of slag and nano-SiO2 could improve the chloride penetration resistance but decrease the compressive strength. Using nano-CaCO3 to coat the aggregate leads to a significant reduction in the properties of the so-prepared concrete. Though coating inert fine particles around aggregate could disturb the initial particle packing and modify the ITZ, it is not able to improve the overall concrete properties. Coating aggregate could determine the ITZ microstructure, especially within the region that is around 30 μm away from aggregate surface.

We have previously observed the predominant expression of nucleoporin 62-like (Nup62l) mRNA in the pharyngeal region of zebrafish, which raises the question whether Nup62l has important implications in governing the morphogenesis of pharyngeal arches (PA) in zebrafish. Herein, we explored the functions of Nup62l in PA development. The disruption of Nup62l with a CRISPR/Cas9-dependent gene knockout approach led to defective PA, which was characterized by a thinned and shortened pharyngeal region and a significant loss of pharyngeal cartilages. During pharyngeal cartilage formation, prechondrogenic condensation and chondrogenic differentiation were disrupted in homozygous nup62l-mutants, while the specification and migration of cranial neural crest cells (CNCCs) were unaffected. Mechanistically, the impaired PA region of nup62l-mutants underwent extensive apoptosis, which was mainly dependent on activation of p53-dependent apoptotic pathway. Moreover, aberrant activation of a series of apoptotic pathways in nup62l-mutants is closely associated with the inactivation of Wnt/β-catenin signaling. Thus, these findings suggest that the regulation of Wnt/β-catenin activity by Nup62l is crucial for PA formation in zebrafish.

A torque ripple mitigation and current hysteresis control for T-type three level (T-3L) inverter fed open-end doubly-salient permanent-magnet motor (DSPM) drives is proposed in this paper. The structure, principle, and characteristics of the DSPM are studied and analyzed and a T-3L inverter fed open-end three-phase DSPM drive configuration is proposed in this paper. Then, this paper introduces a novel commutation strategy to reduce the torque ripple during phase commutation. Furthermore, the multi-loop hysteresis current controller and DC-link voltage balancing algorithm are presented. The effectiveness of the proposed control schemes is verified by both simulation and experimental results.

Climate variation and land use changes have been widely recognized as two major factors that impact hydrological processes. However, it is difficult to distinguish their contributions to changes in streamflow. Quantifying their contributions to alteration of streamflow is especially important for the sustainable management of water resources. In this study, the changes in streamflow for the period of 1960−2008 at two stations (Dongwan and Luhun) were analyzed in the Yihe watershed in China based on hydrological data series and climate parameters. Using a non-parametric Mann−Kendall (MK) and Pettitt’s test, as well as Budyko analysis, we first examined the trends of hydroclimatic variables and the breakpoint of annual streamflow over the past 50 years. Subsequently, we evaluated the contributions of annual precipitation (P), potential evapotranspiration (PET), and land use condition (represented by w), respectively, to streamflow variation. We observed a decreasing trend for P, as well as increasing trends for PET and w. Annual streamflow showed a significant downward trend with an abrupt change occurring in 1985 during the period of 1960−2008. Accordingly, we divided the studied period into two sub-periods: period I (1960−1985) and period II (1986−2008). The sensitivity of the streamflow to the different environmental factors concerned in this study differed. Streamflow was more sensitive to P than to PET and w. The decrease in P was the greatest contributor to the decline in streamflow, which accounted for 50.01% for Dongwan and 55.36% for Luhun, followed by PET, which accounted for 24.25% for Dongwan and 24.45% for Luhun, and land use change was responsible for 25.25% for Dongwan and 20.19% for Luhun. Although land use change plays a smaller role in streamflow reduction, land use optimization and adjustment still have great significance for future water resource management, since climate variation is difficult to control; however, the pattern optimization of land use can be achieved subjectively.

In order to reduce large deformation failure occurrences in non-pillar longwall mining entries due to roof weighting behaviors, a case study in Halagou coal mine was conducted on optimization and control techniques for entry stability in non-pillar longwall mining. The Universal Discrete Element Code (UDEC) modeling was adopted to study entry stability in non-pillar mining, and the characteristics of deformation and stress and crack propagation were revealed. The large deformation transmission between the entry-immediate roof and the gob-immediate roof could be eliminated by optimizing the entry roof structure through a directional roof-cutting method. The localized tensile stresses generated in the entry-surrounding rock caused the generation of coalescent macroscopic fractures, which resulted in the instability of the entry. The tensile stress state could be inhibited by an active flexible support system through enhancing the confining pressure on the surrounding rock. Serious rotation subsidence occurs in the entry roof due to periodic weighting of the main roof, which could be greatly reduced by a passive rigid support pattern. The numerical and field test results both showed that the roof weighting pressure was offloaded by the technique and that the deformation of the entry surrounding the rock in non-pillar mining was quite small. Thus, the technique can effectively ensure the stability of the gob-side entry, which can provide references for entry stability control in non-pillar longwall mining.

A phase-sensitive fluidic biosensor based on a spectral-domain low-coherence interferometer is presented in this paper. With a fiber optic probe employing the common-path interferometric configuration, subnanometric changes in thickness of the molecular layers can be detected through phase analysis of the acquired interference signal from the sensor surface. Advantages of this biosensor include its picometer-scale thickness sensitivity, 13.9-ms time response, and tolerance to the fluctuation in concentration of the target solution. The capabilities of this biosensor in monitoring specific molecular binding and recognizing specific molecular was successfully demonstrated by using the reactions between the molecules of protein A and IgG. The calculated minimum detectable concentration of IgG is 0.11 µg/mL.

Hybrid vigor contributes in a large way to the yield and quality of cotton (Gossypium hirsutum) fiber. Although microRNAs play essential regulatory roles in flower induction and development, it is still unclear if microRNAs are involved in male sterility, as the regulatory molecular mechanisms of male sterility in cotton need to be better defined. In this study, two independent small RNA libraries were constructed and sequenced from the young buds collected from the sporogenous cell formation to the meiosis stage of the male sterile line Yu98-8A and the near-isogenic line. Sequencing revealed 1588 and 1536 known microRNAs and 347 and 351 novel miRNAs from male sterile and male fertile libraries, respectively. MicroRNA expression profiles revealed that 49 conserved and 51 novel miRNAs were differentially expressed. Bioinformatic and degradome analysis indicated the regulatory complexity of microRNAs during flower induction and development. Further RT-qPCR and physiological analysis indicated that, among the different Kyoto Encyclopedia Gene and Genomes pathways, indole-3-acetic acid and gibberellic acid signaling transduction pathways may play pivotal regulatory functions in male sterility.