Search

The innovation inherent to employing expanded polystyrene (EPS) beads lies in its transformative impact on traditional concrete practices. Through the incorporation of EPS beads in concrete mixtures, a novel approach emerges that significantly alters the material’s characteristics, and opens up new avenues for construction and design. Studying the shear behavior of RC beams made with EPS beads is essential for advancing knowledge, improving design practices, ensuring structural integrity, and promoting the effective and responsible use of innovative materials in construction. This research experimentally investigated the effect of using EPS beads and pozzolana aggregate (PA) on the shear behavior of the RC beams. A total of 27 simply supported rectangular beams were cast, using three novel distinct mix designs, and were subjected to two-point load testing until failure. These three mixes were categorized as follows: a control mix, a mix with only EPS, and a mix with EPS, along with an additive. The ultimate failure load was experimentally recorded for all specimens, and the influence of the temperature (300 °C and 600 °C) on the RC beams made with EPS was examined. The findings revealed a reduction in the concrete compressive strength and density in the beams containing EPS and EPS with superplasticizers of (21.7%, 24.9%) and (11.3%, 16.2%), respectively. Additionally, EPS played a significant role in diminishing the ultimate shear capacity of the beams, compared to the control beams, by about 19.4%. However, the addition of a superplasticizer along with the EPS helped to maintain the beam capacity, to some extent. Conversely, the beams exposed to a temperature of 300 °C exhibited an almost similar capacity to that of the control beams without heating. Nevertheless, at 600 °C, the beams displayed a noticeable decrease in the ultimate load capacity, compared to the unheated control beams.

This paper aims to investigate the effect of using different configurations of near-surface mounted carbon-fiber-reinforced polymer (NSM-CFRP) strips on the shear strength of strengthened and rehabilitated reinforced concrete (RC) T-beams with different internal shear stirrup spacing. The internal shear stirrup spacing was 50 and 150 mm. The NSM-CFRP strips were at an inclination of 45° and spaced at 75 and 150 mm. A total of eight beams were tested in this study: two beams without NSM-CFRP as control beams for the purpose of comparison; three beams were strengthened by NSM-CFRP; and three beams were rehabilitated by NSM-CFRP. The experimental shear capacities were compared with the theoretical values predicted by the ACI 440.2R-17. The results indicated that the use of NSM-CFRP strips enhanced the shear capacity for all beams compared to their corresponding control beams. The enhancements in the shear capacity increased with the decrease in the spacing of the internal shear stirrups and NSM-CFRP strips. The ACI 440.2R-17 was conservative in predicting the theoretical shear capacities.

This paper investigates the effect of using near-surface mounted carbon fiber-reinforced polymer (NSM-CFRP) on the shear strengthening of rectangle beams with low strength concrete (f′c = 17 MPa), medium strength concrete (f′c = 32 MPa), and high strength concrete (f′c = 47 MPa). The experimental program was performed by installing NSM-CFRP strips vertically in three different configurations: aligned with the internal stirrups, one vertical NSM-CFRP strip between every two internal stirrups, and two vertical NSM-CFRP strips between every two internal stirrups. All tested beams were simply supported beams and tested under a three-point loading test. The experimental results were compared with the theoretical capacities that were calculated according to the ACI 440.2R-17 and finite element analysis (FEA) that was conducted using ABAQUS software to simulate the behavior of all beams. The experimental results indicated that using NSM-CFRP limited the failure mode of all beams to pure shear failure with no debonding or rapture of the carbon strips. Moreover, the use of NSM-CFRP proved its efficiency by increasing the shear capacity of all beams by a range of 4% to 66%, in which the best enhancement was recorded for the case of using two unaligned NSM-CFRP strips. In general, the experimental shear capacities increased with the increase in the compressive strength of all beams. On the other hand, the ACI 440.2R-17 was conservative in predicting the theoretical shear capacities, and the FEA results agreed well with the experimental results.