Search

This study compares HfO2 ceramics synthesized using sol–gel and combustion methods, emphasizing the impact of the method of synthesis on the resulting properties of the material. The research findings illustrate morphological differences between sol–gel and combustion-derived HfO2. While sol–gel samples displayed irregular nanoparticles with pronounced boundaries, combustion samples revealed more homogeneous structures with particles tending towards coalescence. It was discerned that Eu3+ doping induced oxygen vacancies, stabilizing the tetragonal phase, while subsequent doping with Nb5+ significantly reduced these vacancies, which was also observed in photoluminescence analysis. Furthermore, combustion synthesis left fewer organic residues, with urea presence during synthesis contributing to residual organic components in the material. XPS analysis was used to evaluate the presence of oxygen-deficient hafnia sub-oxide in the samples. The study underscores the important role of tailored synthesis methods in optimizing the properties and applications of HfO2.

We are proposing a novel self-assembled monolayer (SAM) functionalized ZnO nanowires (NWs)-based conductometric sensor for the selective detection of hydrogen (H2). The modulation of the surface electron density of ZnO NWs due to the presence of negatively charged terminal amine groups (−NH2) of monolayers leads to an enhanced electron donation from H2 to ZnO NWs. This, in turn, increases the relative change in the conductance (response) of functionalized ZnO NWs as compared to bare ones. In contrast, the sensing mechanism of bare ZnO NWs is determined by the chemisorbed oxygen ions. The functionalized ZnO NWs exhibit an eight times higher response compared to bare ZnO NWs at an optimal working temperature of 200 °C. Finally, in comparison to studies in the literature involving strategies to enhance the sensing performance of metal oxides toward H2, like decoration with metal nanoparticles, heterostructures, and functionalization with a metal–organic framework, etc., SAM functionalization showed superior sensing results.

To meet today’s requirements, new active catalysts with reduced noble metal content are needed for hydrogen sensing. A palladium-functionalized nanostructured Ni0.5Co2.5O4 catalyst with a total Pd content of 4.2 wt% was synthesized by coprecipitation to obtain catalysts with an advantageous sheet-like morphology and surface defects. Due to the synthesis method and the reducible nature of Ni0.5Co2.5O4 enabling strong metal-metal oxide interactions, the palladium was highly distributed over the metal oxide surface, as determined using scanning transmission electron microscopy and energy-dispersive X-ray investigations. The catalyst tested in planar pellistor sensors showed high sensitivity to hydrogen in the concentration range below the lower flammability limit (LFL). At 400 °C and in dry air, a sensor response of 109 mV/10,000 ppm hydrogen (25% of LFL) was achieved. The sensor signal was 4.6-times higher than the signal of pristine Ni0.5Co2.5O4 (24.6 mV/10,000 ppm). Under humid conditions, the sensor responses were reduced by ~10% for Pd-functionalized Ni0.5Co2.5O4 and by ~27% for Ni0.5Co2.5O4. The different cross-sensitivities of both catalysts to water are attributed to different activation mechanisms of hydrogen. The combination of high sensor sensitivity to hydrogen and high signal stability over time, as well as low cross-sensitivity to humidity, make the catalyst promising for further development steps.

Metal oxide core–shell fibrous nanostructures are promising gas-sensitive materials for the detection of a wide variety of both reducing and oxidizing gases. In these structures, two dissimilar materials with different work functions are brought into contact to form a coaxial heterojunction. The influence of the shell material on the transportation of the electric charge carriers along these structures is still not very well understood. This is due to homo-, hetero- and metal/semiconductor junctions, which make it difficult to investigate the electric charge transfer using direct current methods. However, in order to improve the gas-sensing properties of these complex structures, it is necessary to first establish a good understanding of the electric charge transfer in ambient air. In this article, we present an impedance spectroscopy study of networked SnO2/Ga2O3 core–shell nanobelts in ambient air. Tin dioxide nanobelts were grown directly on interdigitated gold electrodes, using the thermal sublimation method, via the vapor–liquid–solid (VLS) mechanism. Two forms of a gallium oxide shell of varying thickness were prepared via halide vapor-phase epitaxy (HVPE), and the impedance spectra were measured at 189–768 °C. The bulk resistance of the core–shell nanobelts was found to be reduced due to the formation of an electron accumulation layer in the SnO2 core. At temperatures above 530 °C, the thermal reduction of SnO2 and the associated decrease in its work function caused electrons to flow from the accumulation layer into the Ga2O3 shell, which resulted in an increase in bulk resistance. The junction resistance of said core–shell nanostructures was comparable to that of SnO2 nanobelts, as both structures are likely connected through existing SnO2/SnO2 homojunctions comprising thin amorphous layers.

Clean hydrogen is a key aspect of carbon neutrality, necessitating robust methods for monitoring hydrogen concentration in critical infrastructures like pipelines or power plants. While semiconducting metal oxides such as In2O3 can monitor gas concentrations down to the ppm range, they often exhibit cross-sensitivity to other gases like H2O. In this study, we investigated whether cyclic optical illumination of a gas-sensitive In2O3 layer creates identifiable changes in a gas sensor’s electronic resistance that can be linked to H2 and H2O concentrations via machine learning. We exposed nanostructured In2O3 with a large surface area of 95 m2 g−1 to H2 concentrations (0–800 ppm) and relative humidity (0–70%) under cyclic activation utilizing blue light. The sensors were tested for 20 classes of gas combinations. A support vector machine achieved classification rates up to 92.0%, with reliable reproducibility (88.2 ± 2.7%) across five individual sensors using 10-fold cross-validation. Our findings suggest that cyclic optical activation can be used as a tool to classify H2 and H2O concentrations.

This study presents the synthesis of a multicomponent metal oxide electrocatalyst that increases the activity of the oxygen evolution reaction (OER). We synthesized transition metal oxides (MnOx, FeOx, CoOx, and NiOx) with MoO3 heterostructures through a solid-state reaction approach at low cost. In comparison to the other compositions, CoOx garnered higher attention and demonstrated superior performance on account of its large surface area and varied crystal facets. The MnOx-MoO3, FeOx-MoO3, CoOx-MoO3, and NiOx-MoO3 compositions attained an overpotential of 390 mV, 350 mV, 310 mV, and 340 mV, respectively, at a current density of 10 mA cm−2 in alkaline solution. The performance of OER was enhanced in CoOx-MoO3 at 10 mA cm−2, while FeOx-MoO3 exhibited a lower current density at 100 mA cm−2 than other metal oxides. The CoOx-MoO3 material exhibited a favorable crystal interface transition due to the presence of MoO3 oxide. For the first time, we report on the MoO3-to-(MnOx, FeOx, CoOx, and NiOx) interface crystal transition and the active surface area for OER catalytic activity in water-splitting processes. This investigation intends to develop an electrocatalyst that is capable of producing hydrogen with the use of heterostructure metal oxides.

The science of catalysis has a direct impact on the world economy and the energy environment that positively affects the environmental ecosystem of our universe. Any catalyst, before being tested in a reaction, must undergo a specific characterization protocol to simulate its behavior under reaction conditions. In this work, these steps that must be carried out are presented, both generically and with examples, to the support and to the catalyst itself before and after the reaction. The first stage consists of knowing the textural and structural properties of the support used for the preparation of the catalysts. The specific surface area and the pore volume are fundamental properties, measured by N2 adsorption at −196 °C when preparing the catalyst, dispersing the active phase, and allowing the diffusion and reaction of the reactants and products on its surface. If knowing the structure of the catalyst is important to control its behavior against a reaction, being able to analyze the catalyst used under the reaction conditions is essential to have knowledge about what has happened inside the catalytic reactor. The most common characterization techniques in heterogeneous catalysis laboratories are those described in this work. As an application example, the catalytic conversion of CO2 to CH4 has been selected and summarized in this work. In this case, the synthesis and characterization of Cu and Ni catalysts supported on two Al2O3 with different textural properties, 92 and 310 m2/g, that allow for obtaining various metallic dispersions, between 3.3 and 25.5%, is described. The catalytic behavior of these materials is evaluated from the CO2 methanation reaction, as well as their stability from the properties they present before and after the reaction.

Buildings worldwide are becoming more thermally insulated, and air circulation is being reduced to a minimum. As a result, measuring indoor air quality is important to prevent harmful concentrations of various gases that can lead to safety risks and health problems. To measure such gases, it is necessary to produce low-cost and low-power-consuming sensors. Researchers have been focusing on semiconducting metal oxide (SMOx) gas sensors that can be combined with intelligent technologies such as smart homes, smart phones or smart watches to enable gas sensing anywhere and at any time. As a type of SMOx, p-type gas sensors are promising candidates and have attracted more interest in recent years due to their excellent electrical properties and stability. This review paper gives a short overview of the main development of sensors based on copper oxides and their composites, highlighting their potential for detecting CO2 and the factors influencing their performance.

Humidity is a well-known interference factor in metal oxide (MOX) gas sensors, significantly impacting their performance in various applications such as environmental monitoring and medical diagnostics. This study investigates the effects of adsorbed water on MOX conductivity using two different materials: pure tin oxide (SnO2) and a tin–titanium–niobium oxide mixture (SnTiNb)xO2 (STN). The results reveal that (SnTiNb)xO2 sensors exhibit reduced sensitivity to humidity compared to pure tin oxide, rendering them more suitable for applications where humidity presence is critical. We aimed to shed light on a still controversial debate over the mechanisms involved in the water surface interactions for the aforementioned materials also by exploring theoretical studies in the literature. Experimental analysis involves varying temperatures (100 to 800 °C) to understand the kinetics of surface reactions. Additionally, a brief high-temperature heating method is demonstrated to effectively remove adsorbed humidity from sensor surfaces. The study employs Arrhenius-like plots for graphical interpretation, providing insights into various water adsorption/desorption phenomena. Overall, this research contributes to a deeper understanding of the role of humidity in MOX gas sensor mechanisms and offers practical insights for sensor design and optimization.

Triethylamine is a common volatile organic compound (VOC) that plays an important role in areas such as organic solvents, chemical industries, dyestuffs, and leather treatments. However, exposure to triethylamine atmosphere can pose a serious threat to human health. In this study, gas-sensing semiconductor materials of LaFeO3 nano materials with different Mo-doping ratios were synthesized by the sol–gel method. The crystal structures, micro morphologies, and surface states of the prepared samples were characterized by XRD, SEM, and XPS, respectively. The gas-sensing tests showed that the Mo doping enhanced the gas-sensing performance of LaFeO3. Especially, the 4% Mo-doped LaFeO3 exhibited the highest response towards triethylamine (TEA) gas, a value approximately 11 times greater than that of pure LaFeO3. Meantime, the 4% Mo-doped LaFeO3 sensor showed a remarkably robust linear correlation between the response and the concentration (R2 = 0.99736). In addition, the selectivity, stability, response/recovery time, and moisture-proof properties were evaluated. Finally, the gas-sensing mechanism is discussed. This study provides an idea for exploring a new type of efficient and low-cost metal-doped LaFeO3 sensor to monitor the concentration of triethylamine gas for the purpose of safeguarding human health and safety.

Herein, we prepared two different MOS-based gas sensors with integrated micro-hotplates. The two sensors were employed to detect various fragrances (cedar, mandarin orange, rose A, and rose B), exhibiting similarly great sensing performances. The gas sensing properties of the MOS-based sensor depend on the sensor’s operating temperature. In addition to isothermal operation, various pulse heating modes were applied to investigate the gas sensing performances with respect to the four fragrances. Multivariate gas sensing features of the four fragrances were obtained under different operating modes, which were utilized for the recognition of fragrance odors successfully, based on the long short-term memory (LSTM) algorithm.

Production of butadiene from biomass-based tetrahydrofuran (THF) is explored as an alternative to the existing petroleum-based processes. Metal oxide catalysts have been shown to exhibit varying product selectivities when reacted with THF. Among those oxides, ZrO2 showed the highest selectivity for butadiene. In contrast, Al2O3 showed the highest selectivity for the competing retro-Prins products, C3H6 and HCHO. The reasons behind the varying selectivity across oxides are unclear. In this work, we employ periodic density functional theory and mean-field microkinetic modeling to investigate the mechanism of the reaction of THF to butadiene and retro-Prins products on t-ZrO2 (101) (dry and hydrous) and on γ-Al2O3 (110). Our simulations reproduce the experimental selectivity trends. High selectivity for butadiene is promoted by the presence of neighboring Lewis acid metal sites that facilitate E1cB hydroxyl elimination from a 3-butenoxide intermediate; on hydrous Al2O3; where such neighboring Lewis acid centers are not available, the butenoxide undergoes E2 elimination and retro-Prins products ensue. The THF ring opening is rate-determining on ZrO2, whereas the γ-proton elimination that yields the 3-butenoxide intermediate is rate controlling on hydroxylated Al2O3. We conclude that the local topology around the active site greatly influences the mechanism and selectivity.

As a stable, low-cost, environment-friendly, and gas-sensitive material, semiconductor metal oxides have been widely used for gas sensing. In the past few years, single-atom catalysts (SACs) have gained increasing attention in the field of gas sensing with the advantages of maximized atomic utilization and unique electronic and chemical properties and have successfully been applied to enhance the detection sensitivity and selectivity of metal oxide gas sensors. However, the application of SACs in gas sensors is still in its infancy. Herein, we critically review the recent advances and current status of single-atom catalysts in metal oxide gas sensors, providing some suggestions for the development of this field. The synthesis methods and characterization techniques of SAC-modified metal oxides are summarized. The interactions between SACs and metal oxides are crucial for the stable loading of single-atom catalysts and for improving gas-sensitive performance. Then, the current application progress of various SACs (Au, Pt, Cu, Ni, etc.) in metal oxide gas sensors is introduced. Finally, the challenges and perspectives of SACs in metal oxide gas sensors are presented.

A series of metal- and silica-containing carbon-based nanocomposites were synthesized by pyrolysis of a resorcinol–formaldehyde polymer modified with metal oxide/silica nanocomposites (MxOy/SiO2, where M = Mg, Mn, Ni, Cu and Zn) via the thermal oxidative destruction of metal acetates adsorbed on highly dispersed silica (A380). The concentration of metals was 3.0 mmol/g SiO2. The phase composition and morphological, structural and textural properties of the carbon materials were analyzed by X-ray diffraction, SEM, Raman spectroscopy and low-temperature N2 adsorption. Thermal decomposition under a nitrogen atmosphere and in air was analyzed using TG–FTIR and TG–DTG–DSC techniques to determine the influence of the filler on the decomposition process. The synthesized composites show mesoporous structures with high porosity and narrow pore size distributions. It could be shown that the textural properties and the final composition of the nanocomposites depend on the metal oxide fillers of the precursors. The data obtained show that nickel and copper promote the degree of graphitization and a structural order with the highest porosity and largest specific surface area of the hybrid composites. The good adsorption properties of the obtained materials were shown for the recovery of p-chlorophenol and p-nitrophenol from aqueous solutions.

Nitrogen oxide (NOx) pollutants have a significant impact on both the environment and human health. Photocatalytic NOx removal offers a sustainable and eco-friendly approach to combatting these pollutants by harnessing renewable solar energy. Photocatalysis demonstrates remarkable efficiency in removing NOx at sub-scale levels of parts per billion (ppb). The effectiveness of these catalysts depends on various factors, including solar light utilization efficiency, charge separation performance, reactive species adsorption, and catalytic reaction pathway selectivity. Moreover, achieving high stability and efficient photocatalytic activity necessitates a multifaceted materials design strategy. This strategy encompasses techniques such as ion doping, defects engineering, morphology control, heterojunction construction, and metal decoration on metal- or metal oxide-based photocatalysts. To optimize photocatalytic processes, adjustments to band structures, optimization of surface physiochemical states, and implementation of built-in electric field approaches are imperative. By addressing these challenges, researchers aim to develop efficient and stable photocatalysts, thus contributing to the advancement of environmentally friendly NOx removal technologies. This review highlights recent advancements in photocatalytic NOx removal, with a focus on materials design strategies, intrinsic properties, fundamental developmental aspects, and performance validation. This review also presents research gaps, emphasizing the need to understand the comprehensive mechanistic photocatalytic process, favored conditions for generating desired reactive species, the role of water concentration, temperature effects, inhibiting strategies for photocatalyst-deactivating species, and the formation of toxic NO2.

Visible light photodetectors are extensively researched with transparent metal oxide holes/electron layers for various applications. Among the metal oxide transporting layers, nickel oxide (NiO) and zinc oxide (ZnO) are commonly adopted due to their wide band gap and high transparency. The objective of this study was to improve the visible light detection of NiO/ZnO photodiodes by introducing an additional quantum dot (QD) layer between the NiO and ZnO layers. Utilizing the unique property of QDs, we could select different sizes of QDs and responsive light wavelength ranges. The resulting red QDs utilized device that could detect light starting at 635 nm to UV (Ultra-violet) light wavelength and exhibited a photoresponsivity and external quantum efficiency (EQE) of 14.99 mA/W and 2.92% under 635 nm wavelength light illumination, respectively. Additionally, the green QDs, which utilized a device that could detect light starting at 520 nm, demonstrated photoresponsivity values of 8.34 mA/W and an EQE of 1.99% under 520 nm wavelength light illumination, respectively. In addition, we used X-ray photoelectron spectroscopy (XPS) and ultraviolet photoelectron spectroscopy (UPS) to investigate the origin of the photocurrents and the enhancement of the device’s performance. This study suggests that incorporating QDs with metal oxide semiconductors is an effective approach for detecting visible light wavelengths in transparent optoelectronic devices.

This paper presents the integration of a sensing layer over interdigitated electrodes and an electronic circuit on the same flexible printed circuit board. This integration provides an effective technique to use this design as a wearable gas measuring system in a target application, exhibiting high performance, low power consumption, and being lightweight for on-site monitoring. The wearable system proves the concept of using an NFC tag combined with a chemoresistive gas sensor as a cumulative gas sensor, having the possibility of holding the data for a working day, and completely capturing the exposure of a person to NO2 concentrations. Three different types of sensors were tested, depositing the sensing layers on gold electrodes over Kapton substrate: bare graphene, graphene decorated with 5 wt.% zinc oxide nanoflowers, or nanopillars. The deposited layers were characterized using FESEM, EDX, XRD, and Raman spectroscopy to determine their crystalline structure, morphological and chemical compositions. The gas sensing performance of the sensors was analyzed against NO2 (dry and humid conditions) and other interfering species (dry conditions) to check their sensitivity and selectivity. The resultant-built wearable NFC tag system accumulates the data in a non-volatile memory every minute and has an average low power consumption of 24.9 µW in dynamic operation. Also, it can be easily attached to a work vest.

The binary metal oxide mesoporous interfacial layers (bi-MO meso IF layer) templated by a graft copolymer are synthesized between a fluorine-doped tin oxide (FTO) substrate and nanocrystalline TiO2 (nc-TiO2). Amphiphilic graft copolymers, Poly(epichlorohydrin)-graft-poly(styrene), PECH-g-PS, were used as a structure-directing agent, and the fabricated bi-MO meso IF layer exhibits good interconnectivity and high porosity. Even if the amount of ZnO in bi-MO meso IF layer increased, it was confirmed that the morphology and porosity of the bi-MO meso IF layer were well-maintained. In addtion, the bi-MO meso IF layer coated onto FTO substrates shows higher transmittance compared with a pristine FTO substrate and dense-TiO2/FTO, due to the reduced surface roughness of FTO. The overall conversion efficiency (η) of solid-state photovoltaic cells, dye-sensitized solar cells (DSSCs) fabricated with nc-TiO2 layer/bi-MO meso IF layer TZ1 used as a photoanode, reaches 5.0% at 100 mW cm−2, which is higher than that of DSSCs with an nc-TiO2 layer/dense-TiO2 layer (4.2%), resulting from enhanced light harvesting, good interconnectivity, and reduced interfacial resistance. The cell efficiency of the device did not change after 15 days, indicating that the bi-MO meso IF layer with solid-state electrolyte has improved electrode/electrolyte interface and electrochemical stability. Additionally, commercial scattering layer/nc-TiO2 layer/bi-MO meso IF layer TZ1 photoanode-fabricated solid-state photovoltaic cells (DSSCs) achieved an overall conversion efficiency (η) of 6.4% at 100 mW cm−2.

As technologies like the Internet, artificial intelligence, and big data evolve at a rapid pace, computer architecture is transitioning from compute-intensive to memory-intensive. However, traditional von Neumann architectures encounter bottlenecks in addressing modern computational challenges. The emulation of the behaviors of a synapse at the device level by ionic/electronic devices has shown promising potential in future neural-inspired and compact artificial intelligence systems. To address these issues, this review thoroughly investigates the recent progress in metal-oxide heterostructures for neuromorphic applications. These heterostructures not only offer low power consumption and high stability but also possess optimized electrical characteristics via interface engineering. The paper first outlines various synthesis methods for metal oxides and then summarizes the neuromorphic devices using these materials and their heterostructures. More importantly, we review the emerging multifunctional applications, including neuromorphic vision, touch, and pain systems. Finally, we summarize the future prospects of neuromorphic devices with metal-oxide heterostructures and list the current challenges while offering potential solutions. This review provides insights into the design and construction of metal-oxide devices and their applications for neuromorphic systems.

We synthesized zinc oxide nanoparticles (ZnO NPs) by meticulously controlling both temperature and reaction times, allowing us to fine-tune their crystalline properties, morphology, and particle dimensions. This analysis confirmed the existence of a mixture of rod and sphere shapes (ZnO-I), including rod-shaped NPs with an average size of 14.8 nm × 5.2 nm and spherical NPs with an average diameter of 5.27 nm. We subsequently incorporated these synthesized ZnO NPs into organic light-emitting diode (OLED) devices for red, green, and blue colors, utilizing them as the electron injection layer through a solution-based process. The green OLED device using ZnO-I exhibited a promising current efficiency of 4.02 cd/A and an external quantum efficiency of 1.47%.

Nowadays, indoor air pollution is a major problem that affects human health. For that reason, measuring indoor air quality has an increasing interest. Electronic noses are low-cost instruments (compared with reference methods) capable of measuring air components and pollutants at different concentrations. In this paper, an electro-optical nose (electronic nose that includes optical sensors) with non-dispersive infrared sensors and metal oxide semiconductor sensors is used to measure gases that affect indoor air quality. To validate the developed prototype, different gas mixtures (CH4 and CO2) with variable concentrations and humidity values are generated to confirm the discrimination capabilities of the device. Principal Component Analysis (PCA) was used for dimensionality reduction purposes to show the measurements in a plot. Partial Least Squares Regression (PLS) was also performed to calculate the predictive capabilities of the device. PCA results using all the measurements from all the sensors obtained PC1 = 47% and PC2 = 10%; results are improved using only the relevant information of the sensors obtaining PC1 = 79% and PC2 = 9%. PLS results with CH4 using only MOX sensors received an RMSE = 118.8. When using NDIR and MOX sensors, RMSE is reduced to 19.868; this tendency is also observed in CO2 (RMSE = 116.35 with MOX and RMSE = 20.548 with MOX and NDIR). The results confirm that the designed electro-optical nose can detect different gas concentrations and discriminate between different mixtures of gases; also, a better correlation and dispersion is achieved. The addition of NDIR sensors gives better results in measuring specific gases, discrimination, and concentration prediction capabilities in comparison to electronic noses with metal oxide gas sensors.

The ternary composite MgO@ZnO@BC was synthesized and characterized for the adsorption of Cu2+, Pb2+ heavy metal ions from wastewater. The results show that the addition of the MgO@ZnO@BC composite results in higher adsorption properties for Cu2+ and Pb2+, with a molar ratio of 5% 0.1 g, and maximum adsorption capacity (50.63 mg/g for Cu2+ and 61.46 mg/g for Pb2+). The Langmuir adsorption isotherm of the adsorption complex and the kinetics of adsorption are secondary kinetics. The adsorption of Cu2+ and Pb2+ was mainly chemisorption, accompanied by physical adsorption. This adsorption method fully conforms to the concepts of clean production and efficient waste utilization, providing a reference for the removal of heavy metal ions from wastewater and waste recycling using ternary composite materials.

In the last several decades, metal oxide thin films have attracted significant attention for the development of various existing and emerging technological applications, including pH sensors. The mandate for consistent and precise pH sensing techniques has been increasing across various fields, including environmental monitoring, biotechnology, food and agricultural industries, and medical diagnostics. Metal oxide thin films grown using physical vapor deposition (PVD) with precise control over film thickness, composition, and morphology are beneficial for pH sensing applications such as enhancing pH sensitivity and stability, quicker response, repeatability, and compatibility with miniaturization. Various PVD techniques, including sputtering, evaporation, and ion beam deposition, used to fabricate thin films for tailoring materials’ properties for the advanced design and development of high-performing pH sensors, have been explored worldwide by many research groups. In addition, various thin film materials have also been investigated, including metal oxides, nitrides, and nanostructured films, to make very robust pH sensing electrodes with higher pH sensing performance. The development of novel materials and structures has enabled higher sensitivity, improved selectivity, and enhanced durability in harsh pH environments. The last decade has witnessed significant advancements in PVD thin films for pH sensing applications. The combination of precise film deposition techniques, novel materials, and surface functionalization strategies has led to improved pH sensing performance, making PVD thin films a promising choice for future pH sensing technologies.

Sodium-ion battery (SIB) technology started to bloom along with lithium-ion batteries (LIBs) as a supportive energy source to alleviate the cost of lithium sources for the development of energy storage devices and electric vehicles. Layered cathode materials are considered potential candidates to produce high-energy-density batteries. Among the layered cathode materials, P3-type cathodes are the least investigated in spite of their capacities, which are comparable to those of P2-type cathodes. P3-type cathodes show high polarization, leading to a poor cycle life, which impedes their extensive use in practical applications. In this work, we report on zirconium doping as an effective strategy to improve cycling stability and reduce voltage fading, another serious issue of layered cathode materials. It is found that an optimum composition of the P3-type cathode with Zr doping at the Mn site, leading to a composition of Na0.67Ni0.33Mn0.64Zr0.033O2, shows good electrochemical performance in terms of retention (89% after 100 cycles) when compared to Na0.67Ni0.33Mn0.60Zr0.067O2 (85% after 100 cycles) and an undoped sample (83% after 100 cycles). Also, remarkable performance is delivered by the Na0.67Ni0.33Mn0.64Zr0.033O2 sample, with a retention rate of 72% after 450 cycles. This result is also supported by an analysis of the amount of polarization for undoped and doped samples, which found that doping helps in improving the diffusion of ions, and the least polarization is obtained for the Na0.67Ni0.33Mn0.64Zr0.033O2 sample.

Metal oxide nanowires (NWs) with a high surface area, ease of fabrication, and precise control over diameter and chemical composition are among the best candidates for the realization of resistive gas sensors. Among the different techniques used for the synthesis of materials with NW morphology, approaches based on the vapor–liquid–solid (VLS) mechanism are very popular due to the ease of synthesis, low price of starting materials, and possibility of branching. In this review article, we discuss the gas-sensing features of metal oxide NWs grown by the VLS mechanism, with emphasis on the growth conditions and sensing mechanism. The growth and sensing performance of SnO2, ZnO, In2O3, NiO, CuO, and WO3 materials with NW morphology are discussed. The effects of the catalyst type, growth temperature, and other variables on the morphology and gas-sensing performance of NWs are discussed.

The contamination of water by organic substances poses a significant global challenge. To address these pressing environmental and energy concerns, this study emphasizes the importance of developing effective photocatalysts powered by sunlight. In this research, we achieved the successful synthesis of a novel photocatalyst comprised of polymeric carbon nitride (CN) nanosheets embedded with Co3O4 material, denoted as CN-CO. The synthesis process involved subjecting the mixture to 500 °C for 10 h in a muffle furnace. Structural and morphological analyses confirmed the formation of CN-CO nanostructures, which exhibited remarkable enhancements in photocatalytic activity for the removal of methylene blue (MB) pollutants under replicated sunlight. After 90 min of exposure, the degradation rate reached an impressive 98.9%, surpassing the degradation rates of 62.3% for pure CN and 89.32% for pure Co3O4 during the same time period. This significant improvement can be attributed to the exceptional light captivation capabilities and efficient charge separation abilities of the CN-CO nanostructures. Furthermore, the CN-CO nanostructures demonstrated impressive photocurrent density-time (j-t) activity under sunlight, with a photocurrent density of 2.51 μA/cm2 at 0.5 V. The CN-CO nanostructure exhibited excellent methanol oxidation reaction (MOR) activity with the highest current density of 83.71 mA/cm2 at an optimal 2 M methanol concentration, benefiting from the synergy effects of CN and CO in the nanostructure. Overall, this study presents a straightforward and effective method for producing CN-based photocatalysts decorated with semiconductor nanosized materials. The outcomes of this research shed light on the design of nanostructures for energy-related applications, while also providing insights into the development of efficient photocatalytic materials for addressing environmental challenges.

To meet today's requirements, new active catalysts with reduced noble metal content are needed for hydrogen sensing. A palladium-functionalized nanostructured Ni 0.5 Co 2.5 O 4 catalyst with a total Pd content of 4.2 wt% was synthesized by coprecipitation to obtain catalysts with an advantageous sheet-like morphology and surface defects. Due to the synthesis method and the reducible nature of Ni 0.5 Co 2.5 O 4 enabling strong metal-metal oxide interactions, the palladium was highly distributed over the metal oxide surface, as determined using scanning transmission electron microscopy and energy-dispersive X-ray investigations. The catalyst tested in planar pellistor sensors showed high sensitivity to hydrogen in the concentration range below the lower flammability limit (LFL). At 400 °C and in dry air, a sensor response of 109 mV/10,000 ppm hydrogen (25% of LFL) was achieved. The sensor signal was 4.6-times higher than the signal of pristine Ni 0.5 Co 2.5 O 4 (24.6 mV/10,000 ppm). Under humid conditions, the sensor responses were reduced by ~10% for Pd-functionalized Ni 0.5 Co 2.5 O 4 and by ~27% for Ni 0.5 Co 2.5 O 4 . The different cross-sensitivities of both catalysts to water are attributed to different activation mechanisms of hydrogen. The combination of high sensor sensitivity to hydrogen and high signal stability over time, as well as low cross-sensitivity to humidity, make the catalyst promising for further development steps.

The work presented in this paper describes the preparation and the electrochemical application of functionalized chitosan-entrapped carbon paste electrodes (CH/CPE) for lead ions (Pb2+) detection in industrial wastewater. The chitosan was first functionalized using TiO2 and CuO, which were both metal oxides that were obtained by extracting it from waste products derived from shrimp shells. The analytical performance of the as-prepared electrodes, CH/CPE, TiO2-CH/CPE, and NiO-CH/CPE, for the detection of lead (II) was examined using electrochemical impedance spectroscopy (EIS) technique in the 0.1 M KNO3 electrolyte solution. The effect of experimental conditions, including polarization potential, frequency, and pH, are optimized to maximize the sensitivity of the measurements. The developed impedimetric sensors provided a linear response over a concentration range of 10−6 to 10−4 M with a detection limit of 3.10−7 M based on S/N = 3. The DFT computational analysis demonstrated that chitosan biopolymer possesses the ability to adsorb Pb (II) ions that are present in wastewater. Chitosan and the derivatives of chitosan, have the potential to remove heavy metals from industrial effluent in a manner that is both economical and eco-friendly to the environment. Chitosan is a biopolymer that is abundantly renewable.

The improper disposal of toxic and carcinogenic organic substances resulting from the manufacture of dyes, drugs and pesticides can contaminate aquatic environments and potable water resources and cause serious damage to animal and human health and to the ecosystem. In this sense, heterogeneous photocatalysis stand out as one effective and cost-effective water depollution technique. The use of metal oxide nanocomposites (MON), from the mixture of two or more oxides or between these oxides and other functional semiconductor materials, have gained increasing attention from researchers and industrial developers as a potential alternative to produce efficient and environmentally friendly photocatalysts for the remediation of water contamination by organic compounds. Thus, this work presents an updated review of the main advances in the use of metal oxide nanocomposites-based photocatalysts for decontamination of water polluted by these substances. A bibliometric analysis allowed to show the evolution of the importance of this research topic in the literature over the last decade. The results of the study also showed that hierarchical and heterogeneous nanostructures of metal oxides, as well as conducting polymers and carbon materials, currently stand out as the main materials for the synthesis of MON, with better photocatalysis performance in the degradation of dyes, pharmaceuticals and pesticides.

The present review article discusses the elementary concepts of the sensor mechanism and various types of materials used for sensor applications. The electrospinning method is the most comfortable method to prepare the device-like structure by means of forming from the fiber structure. Though there are various materials available for sensors, the important factor is to incorporate the functional group on the surface of the materials. The post-modification sanction enhances the efficiency of the sensor materials. This article also describes the various types of materials applied to chemical and biosensor applications. The chemical sensor parts include acetone, ethanol, ammonia, and CO2, H2O2, and NO2 molecules; meanwhile, the biosensor takes on glucose, uric acid, and cholesterol molecules. The above materials have to be sensed for a healthier lifestyle for humans and other living organisms. The prescribed review articles give a detailed report on the Electrospun materials for sensor applications.

Cryogels from noble metal NPs have proven to be highly efficient catalysts due to their high specific surface area which increases the mass transfer channels and catalytic active sites. By using metal oxides as co-catalysts, the costs of the material can be significantly reduced, while the catalytic activity can remain the same or even improve due to synergetic effects. In this work, we synthesize different cryogel thin films supported on modified ITO substrates from Pt, Pd nanoparticles (NPs), and mixtures of these noble metals with γ-Fe2O3 NPs in a very low concentration (1 wt% of the noble metal). Structural and elemental analysis of the samples are performed, along with the measurement and analysis of their catalytic activity. The electrocatalytic activity of the cryogels towards ethanol oxidation reaction (EOR) in alkaline media was evaluated by means of cyclic voltammetry. By mixing γ-Fe2O3 NPs with Pt or Pd NPs in the cryogel structure, we observe increased tolerance against poisonous surface intermediates produced during the EOR. Moreover, we observe an increase in the catalytic activity towards EOR in the case of the 1 wt% Pd/γ-Fe2O3 cryogel, making them promising materials for the development of direct ethanol fuel cells.

In the present work, a study was carried out with the aim of enhancing the performance of electrochemical biosensors based on Co3O4:Fe2O3 heterojunctions. Specifically, the redox behavior of screen–printed carbon electrodes (SPCEs) modified with Co3O4:Fe2O3 (0.5 wt%:x wt%) nanocomposites, where x ranged from 0.1 to 0.5 wt%, was examined in detail. The hybrid nanocomposites were synthesized using the sol-gel auto-combustion method. Several characterization methods were performed to investigate the morphology, microstructure, and surface area of the pure Co3O4, pure Fe2O3, and the synthesized Co3O4:Fe2O3 nanocomposites. Using cyclic voltammetry (CV) tests, the electrochemical behavior of the modified electrodes toward the dopamine (DA) molecules was investigated. The modified Co3O4:Fe2O3, (0.5 wt%, x = 0.4 wt%)/SPCE resulted in a sensor with the best electrochemical performance toward DA. A high linear relationship between DA concentrations and the faradic current variation (ipa (μA) = 0.0736 + 0.1031 CDA (μA) and R2 = 0.99) was found in the range of 10–100 μM. The sensitivity value was computed to be 0.604 µA µM−1cm−2 and the limit of detection (LOD) 0.24 µM. Based on the characterization and electrochemical results, it can be suggested that the formation of Co3O4:Fe2O3 heterostructures provides a large specific surface area, an increased number of electroactive sites at the metal oxide interface and a p–n heterojunction, thus ensuring a remarkable enhancement in the electrochemical response towards DA.

Converting and storing solar energy directly as chemical energy through photoelectrochemical devices are promising strategies to replace fossil fuels. Metal oxides are commonly used as photoanode materials, but they still encounter challenges such as limited light absorption, inefficient charge separation, sluggish surface reactions, and insufficient stability. The regulation of surface oxygen species on metal oxide photoanodes has emerged as a critical strategy to modulate molecular and charge dynamics at the reaction interface. However, the precise role of surface oxygen species in metal oxide photoanodes remains ambiguous. The review focuses on elucidating the formation and regulation mechanisms of various surface oxygen species in metal oxides, their advantages and disadvantages in photoelectrochemical reactions, and the characterization methods employed to investigate them. Additionally, the article discusses emerging opportunities and potential hurdles in the regulation of surface oxygen species. By shedding light on the significance of surface oxygen species, this review aims to advance our understanding of their impact on metal oxide photoanodes, paving the way for the design of more efficient and stable photoelectrochemical devices.

The quest for a cost-effective, chemically-inert, robust and proton conducting membrane for flow batteries is at its paramount. Perfluorinated membranes suffer severe electrolyte diffusion, whereas conductivity and dimensional stability in engineered thermoplastics depend on the degree of functionalization. Herein, we report surface-modified thermally crosslinked polyvinyl alcohol-silica (PVA-SiO2) membranes for the vanadium redox flow battery (VRFB). Hygroscopic, proton-storing metal oxides such as SiO2, ZrO2 and SnO2 were coated on the membranes via the acid-catalyzed sol-gel strategy. The membranes of PVA-SiO2-Si, PVA-SiO2-Zr and PVA-SiO2-Sn demonstrated excellent oxidative stability in 2 M H2SO4 containing 1.5 M VO2+ ions. The metal oxide layer had good influence on conductivity and zeta potential values. The observed trend for conductivity and zeta potential values was PVA-SiO2-Sn > PVA-SiO2-Si > PVA-SiO2-Zr. In VRFB, the membranes showcased higher Coulombic efficiency than Nafion-117 and stable energy efficiencies over 200 cycles at the 100 mA cm−2 current density. The order of average capacity decay per cycle was PVA-SiO2-Zr < PVA-SiO2-Sn < PVA-SiO2-Si < Nafion-117. PVA-SiO2-Sn had the highest power density of 260 mW cm−2, while the self-discharge for PVA-SiO2-Zr was ~3 times higher than Nafion-117. VRFB performance reflects the potential of the facile surface modification technique to design advanced membranes for energy device applications.

Intermolecular interactions on inorganic substrates can have a critical impact on the electrochemical and photophysical properties of the materials and subsequent performance in hybrid electronics. Critical to the intentional formation or inhibition of these processes is controlling interactions between molecules on a surface. In this report, we investigated the impact of surface loading and atomic-layer-deposited Al2O3 overlayers on the intermolecular interactions of a ZrO2-bound anthracene derivative as probed by the photophysical properties of the interface. While surface loading density had no impact on the absorption spectra of the films, there was an increase in excimer features with surface loading as observed by both emission and transient absorption. The addition of ALD overlayers of Al2O3 resulted in a decrease in excimer formation, but the emission and transient absorption spectra were still dominated by excimer features. These results suggest that ALD may provide a post-surface loading means of influencing such intermolecular interactions.

The development of new materials for the construction sector is a global trend, and products that use by-products in their composition and have also incorporated technology are commercially competitive. Microparticles have large surface areas and can modify the microstructure of materials, positively affecting their physical and mechanical properties. In this context, this study aims to investigate the effect of incorporating aluminium oxide (Al2O3) microparticles on the physical and mechanical properties of oriented strand boards (OSBs) made from reforested residual balsa and castor oil polyurethane resin and to evaluate their durability performance under accelerated aging conditions. The OSBs were produced on a laboratory scale with a density of 650 kg/m3, strand-type particles measuring 90 × 25 × 1 mm3, using castor oil-based polyurethane resin (13%) and Al2O3 microparticle content ranging from 1% to 3% of the resin mass. The physical and mechanical properties of the OSBs were determined following the EN-300:2002 recommendations. The results obtained indicated that the OSBs with 2% Al2O3 presented thickness swelling significantly lower (at the 5% significance level) after being subjected to accelerated aging and internal bonding of the particles higher than the values obtained for the references, evidencing the positive effect of including Al2O3 microparticles in balsa OSBs.

Thin nanocomposite films based on zinc oxide (ZnO) added with cobalt oxide (Co3O4) were synthesized by solid-phase pyrolysis. According to XRD, the films consist of a ZnO wurtzite phase and a cubic structure of Co3O4 spinel. The crystallite sizes in the films increased from 18 nm to 24 nm with growing annealing temperature and Co3O4 concentration. Optical and X-ray photoelectron spectroscopy data revealed that enhancing the Co3O4 concentration leads to a change in the optical absorption spectrum and the appearance of allowed transitions in the material. Electrophysical measurements showed that Co3O4-ZnO films have a resistivity up to 3 × 104 Ohm∙cm and a semiconductor conductivity close to intrinsic. With advancing the Co3O4 concentration, the mobility of the charge carriers was found to increase by almost four times. The photosensors based on the 10Co-90Zn film exhibited a maximum normalized photoresponse when exposed to radiation with wavelengths of 400 nm and 660 nm. It was found that the same film has a minimum response time of ca. 26.2 ms upon exposure to radiation of 660 nm wavelength. The photosensors based on the 3Co-97Zn film have a minimum response time of ca. 58.3 ms versus the radiation of 400 nm wavelength. Thus, the Co3O4 content was found to be an effective impurity to tune the photosensitivity of radiation sensors based on Co3O4-ZnO films in the wavelength range of 400–660 nm.

The high hydrogen storage capacity (10.5 wt.%) and release of hydrogen at a moderate temperature make LiAlH4 an appealing material for hydrogen storage. However, LiAlH4 suffers from slow kinetics and irreversibility. Hence, LaCoO3 was selected as an additive to defeat the slow kinetics problems of LiAlH4. For the irreversibility part, it still required high pressure to absorb hydrogen. Thus, this study focused on the reduction of the onset desorption temperature and the quickening of the desorption kinetics of LiAlH4. Here, we report the different weight percentages of LaCoO3 mixed with LiAlH4 using the ball-milling method. Interestingly, the addition of 10 wt.% of LaCoO3 resulted in a decrease in the desorption temperature to 70 °C for the first stage and 156 °C for the second stage. In addition, at 90 °C, LiAlH4 + 10 wt.% LaCoO3 can desorb 3.37 wt.% of H2 in 80 min, which is 10 times faster than the unsubstituted samples. The activation energies values for this composite are greatly reduced to 71 kJ/mol for the first stages and 95 kJ/mol for the second stages compared to milled LiAlH4 (107 kJ/mol and 120 kJ/mol for the first two stages, respectively). The enhancement of hydrogen desorption kinetics of LiAlH4 is attributed to the in situ formation of AlCo and La or La-containing species in the presence of LaCoO3, which resulted in a reduction of the onset desorption temperature and activation energies of LiAlH4.

Redox materials have been investigated for various thermochemical processing applications including solar fuel production (hydrogen, syngas), ammonia synthesis, thermochemical energy storage, and air separation/oxygen pumping, while involving concentrated solar energy as the high-temperature process heat source for solid–gas reactions. Accordingly, these materials can be processed in two-step redox cycles for thermochemical fuel production from H2O and CO2 splitting. In such cycles, the metal oxide is first thermally reduced when heated under concentrated solar energy. Then, the reduced material is re-oxidized with either H2O or CO2 to produce H2 or CO. The mixture forms syngas that can be used for the synthesis of various hydrocarbon fuels. An alternative process involves redox systems of metal oxides/nitrides for ammonia synthesis from N2 and H2O based on chemical looping cycles. A metal nitride reacts with steam to form ammonia and the corresponding metal oxide. The latter is then recycled in a nitridation reaction with N2 and a reducer. In another process, redox systems can be processed in reversible endothermal/exothermal reactions for solar thermochemical energy storage at high temperature. The reduction corresponds to the heat charge while the reverse oxidation with air leads to the heat discharge for supplying process heat to a downstream process. Similar reversible redox reactions can finally be used for oxygen separation from air, which results in separate flows of O2 and N2 that can be both valorized, or thermochemical oxygen pumping to absorb residual oxygen. This review deals with the different redox materials involving stoichiometric or non-stoichiometric materials applied to solar fuel production (H2, syngas, ammonia), thermochemical energy storage, and thermochemical air separation or gas purification. The most relevant chemical looping reactions and the best performing materials acting as the oxygen carriers are identified and described, as well as the chemical reactors suitable for solar energy absorption, conversion, and storage.

The search for inexpensive, environmentally friendly, and highly effective catalysts to activate C-H bonds in propane dehydrogenation (PDH) reactions is still a major challenge. Co-based catalysts have gained significant attention in recent years due to their excellent ability to activate C-H bonds and their high selectivity towards olefins, despite being a non-noble and environmentally unfriendly metal. However, further improvements are necessary for practical utilization, particularly in terms of activity and anti-carbon deposition capacity. In this study, we synthesized Al2O3 nanorods with abundant pentacoordinated Al3+ (Al3+penta) sites. The supported Co on the Al2O3 nanorod (Co/Al2O3-NR) exhibited higher selectivity (>96% propylene selectivity) and stability (deactivation rate 0.15 h−1) compared to Co supported on an Al2O3 nanosheet with fewer pentacoordinated Al3+ sites. Various characterizations confirmed that Co(II) mainly exists as CoAl2O4 rather than Co3O4 in the form of Co/Al2O3-NR, which inhibits the reduction of Co(II) to Co0 and accordingly improves catalyst stability.

Metal oxide-based conductometric gas sensors (CGS) have showcased a vast application potential in the fields of environmental protection and medical diagnosis due to their unique advantages of high cost-effectiveness, expedient miniaturization, and noninvasive and convenient operation. Of multiple parameters to assess the sensor performance, the reaction speeds, including response and recovery times during the gas–solid interactions, are directly correlated to a timely recognition of the target molecule prior to scheduling the relevant processing solutions and an instant restoration aimed for subsequent repeated exposure tests. In this review, we first take metal oxide semiconductors (MOSs) as the case study and conclude the impact of the semiconducting type as well as the grain size and morphology of MOSs on the reaction speeds of related gas sensors. Second, various improvement strategies, primarily including external stimulus (heat and photons), morphological and structural regulation, element doping, and composite engineering, are successively introduced in detail. Finally, challenges and perspectives are proposed so as to provide the design references for future high-performance CGS featuring swift detection and regeneration.

The controlled and efficient formation of oxygen vacancies on the surface of metal oxide semiconductors is required for their use in gas sensors. This work addresses the gas-sensing behaviour of tin oxide (SnO2) nanoparticles for nitrogen oxide (NO2), NH3, CO, and H2S detection at various temperatures. Synthesis of SnO2 powder and deposition of SnO2 film is conducted using sol-gel and spin-coating methods, respectively, as these methods are cost-effective and easy to handle. The structural, morphological, and optoelectrical properties of nanocrystalline SnO2 films were studied using XRD, SEM, and UV-visible characterizations. The gas sensitivity of the film was tested by a two-probe resistivity measurement device, showing a better response for the NO2 and outstanding low-concentration detection capacity (down to 0.5 ppm). The anomalous relationship between specific surface area and gas-sensing performance indicates the SnO2 surface’s higher oxygen vacancies. The sensor depicts a high sensitivity at 2 ppm for NO2 with response and recovery times of 184 s and 432 s, respectively, at room temperature. The result demonstrates that oxygen vacancies can significantly improve the gas-sensing capability of metal oxide semiconductors.

One of the ideal energy carriers for the future is hydrogen. It has a high energy density and is a source of clean energy. A crucial step in the development of the hydrogen economy is the safety and affordable storage of a large amount of hydrogen. Thus, owing to its large storage capacity, good reversibility, and low cost, Magnesium hydride (MgH2) was taken into consideration. Unfortunately, MgH2 has a high desorption temperature and slow ab/desorption kinetics. Using the ball milling technique, adding cobalt lanthanum oxide (LaCoO3) to MgH2 improves its hydrogen storage performance. The results show that adding 10 wt.% LaCoO3 relatively lowers the starting hydrogen release, compared with pure MgH2 and milled MgH2. On the other hand, faster ab/desorption after the introduction of 10 wt.% LaCoO3 could be observed when compared with milled MgH2 under the same circumstances. Besides this, the apparent activation energy for MgH2–10 wt.% LaCoO3 was greatly reduced when compared with that of milled MgH2. From the X-ray diffraction analysis, it could be shown that in-situ forms of MgO, CoO, and La2O3, produced from the reactions between MgH2 and LaCoO3, play a vital role in enhancing the properties of hydrogen storage of MgH2.

Magnesium hydrides (MgH2) have drawn a lot of interest as a promising hydrogen storage material option due to their good reversibility and high hydrogen storage capacity (7.60 wt.%). However, the high hydrogen desorption temperature (more than 400 °C) and slow sorption kinetics of MgH2 are the main obstacles to its practical use. In this research, nickel zinc oxide (Ni0.6Zn0.4O) was synthesized via the solid-state method and doped into MgH2 to overcome the drawbacks of MgH2. The onset desorption temperature of the MgH2–10 wt.% Ni0.6Zn0.4O sample was reduced to 285 °C, 133 °C, and 56 °C lower than that of pure MgH2 and milled MgH2, respectively. Furthermore, at 250 °C, the MgH2–10 wt.% Ni0.6Zn0.4O sample could absorb 6.50 wt.% of H2 and desorbed 2.20 wt.% of H2 at 300 °C within 1 h. With the addition of 10 wt.% of Ni0.6Zn0.4O, the activation energy of MgH2 dropped from 133 kJ/mol to 97 kJ/mol. The morphology of the samples also demonstrated that the particle size is smaller compared with undoped samples. It is believed that in situ forms of NiO, ZnO, and MgO had good catalytic effects on MgH2, significantly reducing the activation energy and onset desorption temperature while improving the sorption kinetics of MgH2.

Tungsten oxide thin films have applications in various energy-related devices owing to their versatile semiconductor properties, which depend on the oxygen content and crystalline state. The concentration of electrons increases with intrinsic defects such as oxygen vacancies, which create new absorption bands that give rise to colored films. Disorders in the crystal structure produce additional changes in the electrical and optical characteristics. Here, WO3−x thin films are prepared on unheated glass substrates by reactive DC sputtering from a pure metal target, using the discharge power and the oxygen-to-argon pressure ratio as control parameters. A transition from amorphous to polycrystalline state is obtained by increasing the sputtering power and adjusting the oxygen content. The surface roughness is higher and the bandgap energy is lower for polycrystalline layers than for amorphous ones. Moreover, the electrical conductivity and sub-bandgap absorption increase as the oxygen content decreases.

Nowadays, most medical-diagnostic, environmental monitoring, etc. devices employ sensors whose fabrication reproducibility and response repeatability assessment are crucial. The former consists of large-scale sensor manufacture through a standardized process with almost identical morphology and behavior, while the latter consists of giving the same response upon repeating the same stimulus. The thermo-activated chemoresistive sensors, which change their conductance by interacting with the molecules composing the surrounding gas, are currently employed in many devices: in particular, thick-film (SnTiNb)O2 nanosensors were demonstrated to be particularly suitable in the medical and biological fields. Therefore, a set of thirteen of them, randomly selected from the same screen-printing deposition, were laboratory tested, and the outcomes were statistically analyzed in order to assess their consistency. At first, the working temperature that maximized both the sensor sensitivity and response repeatability was identified. Then, the sensors were subjected to different gas concentrations and humidities at this optimal working temperature. It resulted in the (SnTiNb)O2 nanosensors detecting and discriminating CO concentrations as low as 1 ppm and at high humidity degrees (up to 40%) with high repeatability since the response relative standard error ranged from 0.8 to 3.3% for CO and from 3.6 to 5.4% for water vapor.

The τ-phase Ba1.3Ca0.7SiO4 alkaline earth silicate powders were synthesized using the solution combustion technique. For this purpose, metal nitrate–urea mixtures were used as an oxidant and a fuel. Urea’s main function was to help lower the nominal combustion temperature (~550 °C) of the mixtures through exothermic reactions, leading to a relatively mild post-annealing temperature (~750 °C). If the urea concentration increased, the interconnected silicate particle size decreased with nanoscale crystallite (average, 33 ± 3 nm), affecting optical properties. Finally, the photoluminescence spectra suggested that the light emission was through trap sites, because the emitted blue and green lights (2.6 and 2.3 eV, respectively) were smaller than the bandgap (~3.2 eV) of the Ba1.3Ca0.7SiO4 semiconductor.

The increasing concentration of anthropogenic CO2 in the air is one of the main causes of global warming. The Paris Agreement at COP 21 aims to reach the global peak of greenhouse gas emissions in the second half of this century, with CO2 conversion towards valuable added compounds being one of the main strategies, especially in the field of heterogeneous catalysis. In the current search for new catalysts, the deposition of metallic nanoparticles (NPs) supported on metal oxides and metal carbide surfaces paves the way to new catalytic solutions. This review provides a comprehensive description and analysis of the relevant literature on the utilization of metal-supported NPs as catalysts for CO2 conversion to useful chemicals and propose that the next catalysts generation can be led by single-metal-atom deposition, since in general, small metal particles enhance the catalytic activity. Among the range of potential indicators of catalytic activity and selectivity, the relevance of NPs’ size, the strong metal–support interactions, and the formation of vacancies on the support are exhaustively discussed from experimental and computational perspective.

There is a recognized need for the development of cost-effective, stable, fast, and optimized novel materials for technological applications. Substantial research has been undertaken on the role of polymeric nanocomposites in sensing applications. However, the use of PANI-based nanocomposites in impedimetric and capacitive electrochemical sensors has yet to be understood. The present study aimed to explore the relationship between the sensitivity and linearity of electrochemical pH sensors and the composition of nanocomposites. Thin films of PANI/CeO2 and PANI/WO3 were deposited via spin coating for characterization and application during the electrochemical impedance and capacitance spectroscopy (EIS and ECS) transduction stages. The findings showed that the optimized performance of the devices was extended not only to the sensitivity but also to the linearity. An increase of 213% in the ECS sensitivity of the PANI/CeO2 compared to the metal oxide and an increase of 64% in the ECS linearity of the PANI/WO3 compared to the polymeric sensitivity were reported. This study identified the structure–property relationship of nanocomposite thin films of PANI with metal oxides for use in electrochemical sensors. The developed materials could be applied in devices to be used in different fields, such as food, environment, and biomedical monitoring.

Natural deep eutectic solvents (NDESs), as a new type of green solvent, are used in many fields, including industry in extraction processes, medicine, pharmaceuticals, metallurgy, electrodeposition, separations, gas capture, biocatalysis and nanotechnology. Mainly due to their properties, such as simple preparation, environmental friendliness, biocompatibility and multifunctionality, they are being used in various fields of industry. This review aims to provide insight into the applications of natural deep eutectic solvents, specifically in nanotechnology processes. It focuses on the description of NDES and how their physicochemical properties are used to obtain functional nanomaterials, including metals, metal oxides and salts. It highlights how the use of NDESs to obtain a wide range of inorganic nanoparticles enables the elimination of disadvantages of traditional methods of obtaining them, including reducing energy consumption and functionalising nanoparticles in situ. In conclusion, recent advances and future directions in the development and applications of NDESs in nanotechnology are discussed with the aim of identifying unexplained scientific questions that can be investigated in the future.