Search

(1) Background: Orthopedic surgery has been transformed by 3D-printed personalized instruments (3DP-PSIs), which enhance precision and reduce complications. Hospitals are adopting in-house 3D printing facilities, using cost-effective methods like Fused Deposition Modeling (FDM) with materials like Polylactic acid (PLA) to create 3DP-PSI. PLA’s temperature limitations can be overcome by annealing High-Temperature PLA (ann-HTPLA), enabling steam sterilization without compromising properties. Our study examines the in vivo efficacy of ann-HTPLA 3DP-PSI in pediatric orthopedic surgery. (2) Methods: we investigated safety and efficacy using ann-HTPLA 3DP-PSI produced at an “in-office” 3D-printing Point-of-Care (3DP-PoC) aimed at correcting limb deformities in pediatric patients. Data on 3DP-PSI dimensions and printing parameters were collected, along with usability and complications. (3) Results: Eighty-three ann-HTPLA 3DP-PSIs were utilized in 33 patients (47 bone segments). The smallest guide used measured 3.8 cm3, and the largest measured 58.8 cm3. Seventy-nine PSIs (95.2%; 95% C.I.: 88.1–98.7%) demonstrated effective use without issues. Out of 47 procedures, 11 had complications, including 2 infections (4.3%; 95% CI: 0.5–14.5%). Intraoperative use of 3DP-PSIs did not significantly increase infection rates or other complications. (4) Conclusions: ann-HTPLA has proven satisfactory usability and safety as a suitable material for producing 3DP-PSI in an “in-office” 3DP-PoC.

In the contemporary automobile scene, environmental effect abatement is being increasingly sought; this demands a full rethinking of the entire system and entails more than just the reduction in exhaust pollutant emissions. Currently, the most popular approach is the electrification of automobiles, which significantly reduces pollution in major urban areas while simultaneously posing a new set of problems. The two types of zero-emission vehicles that are now being developed the most are hydrogen fuel cells and battery electric cars, but another option is the Hydrogen Internal Combustion Engine (HYICE) engine, which is highly advantageous in terms of pollutants, aside from Nitrogen Oxides (NOx), which can be considerably decreased. The purpose of this study is to develop a novel vehicle design that transports this type of technology into a sporting context while striving for considerable environmental benefits and integrating them into a society where the love of automobiles still has a strong following. The cutting-edge Industrial Design Structure (IDeS) methodology is used in this work, and a sample structure was created to demonstrate how the problems and technical limitations represented can be solved. The steps of the methodology are followed to shape the final product, with careful consideration given to the design of the styling component through the use of the Stylistic Design Engineering (SDE) method. With the ultimate goal of achieving sustainable driving pleasure, the study looks into whether recyclable materials can be used for the body and whether extremely light materials can be used for the chassis.

Recent analysis has shown deteriorating traffic conditions in urban areas, caused by an increase in the motorization rate, which has risen to 66.6 vehicles per 100 inhabitants. As a result of the pandemic, individuality has grown, hence private vehicles are becoming more prevalent whilst public transport and sharing are negatively affected. Therefore, European policies have encouraged and innovated more sustainable mobility. Thus, the developed project aims to achieve more efficient mobility and more sustainable environments, towards social and economic well-being. The proposed means of transport aims to appeal to an audience with a reduced ability to drive a car as intended. The IDeS methodology was applied to develop a self-driving, urban micro mobility vehicle, aimed to give enough room and equipment for people with moving disabilities. The innovation of the IDeS method is state-of-the-art and ought to satisfy current product needs, which leads to an innovative micromobility vehicle and portrays a design for a car that will help to close the gaps in urban mobility. These design processes, which are distinguished by the fusion of several industrial techniques, enabled the development of a plan that addresses current mobility issues for disabled people and opens to new mobility prospects.

A deep research and analysis of a “critical waste” object has been carried out, understood as a subject that does not fare high on the separate collection and recycling system yet: the cigarette butt. This acknowledged social waste is the first among all the garbage detected everywhere around neighborhoods worldwide, and is therefore the epicenter of a situation so worrying that it is necessary to find a solution concerning the environmental pollution. The present exercise was developed, by means of proper product design methods like TRIZ and QFD driven by DFSS rulings, to conceive of new products and services in order to create incentive for the smokers to lessen the environmental pollution problem. The social implications are about the possibility of modifying the bad habits of the smokers and making the user act consciously towards the environment. Throwing the cigarette-stub in the new collection device, rather than on the ground, enables users to enjoy both moral and economic returns. The “Buttalo” service is aimed to incentivize the population to fight against environmental pollution whilst helping smokers to be conscious about it.

Urban mobility scenarios are constantly evolving, and today’s solutions may not be adequate in the future. Through innovative analysis and design methods encapsulated by the IDeS methodology, it is possible to plausibly hypothesize a number of key scenarios to be analyzed, for which vehicles can be designed in order to solve the main problems. Scenarios such as the steady growth in public mobility, based on the sharing of electric mini-buses at the expense of the privatization of the means of transport, lead to the gradual rethinking of citizens’ needs and the supporting infrastructure. Problems such as the lack of privacy of public vehicles, the efficiency of the infrastructure and recharging modes of e-buses, and autonomous driving are addressed here through methods such as QFD (quality function deployment) and SDE (stylistic design engineering), with the aim of outlining a proposal that, to date, is futuristic but is designed to be concrete and feasible within the next decade. These methodologies were applied to the design of a sustainable urban transport system consisting of an electric mini-bus, effected by rethinking the layout of the interior spaces in favor of areas enabling greater privacy and a mobile recharging system (MBS) capable of offering a new management strategy for the non-stop recharging phase. Through the use of an MBS, which functions as a mobile ‘energy bank’ module that is capable of autonomously reaching a mini-bus in need of recharging and extending its autonomy by connecting and recharging it, the proposed system can potentially be enabled to perform its required service during the day without any need to spend time making intermediate stops for the purpose of recharging.

This case study aims to develop a new innovative SUV (Sport Utility Vehicle) model exploiting IDeS (Industrial Design Structure), which is an engineering approach conceived to optimize car design projects in the automotive industry like never before. A compact SUV was chosen because it is a type of vehicle that is highly requested by customers, and it is extremely successful in the market due to its versatility. In fact, compact SUVs are mixed vehicles that combine the pragmatism of a car with the typical robustness of an off-road vehicle making them suitable both for urban and off-road scenarios. The following pages will illustrate the steps followed for the realization of the final product using the SDE (Stylistic Design Engineering) method and other various design technologies, such as Quality Function Deployment (QFD), Benchmarking (BM) and Top Flop Analysis (TPA). In the final part of this project, the virtual prototyping of the product is carried out using Additive Manufacturing (AM) with an FDM 3D printer. The combination of these methods forms, to all intents and purposes, the IDeS, a newly developed innovative and cutting-edge discipline capable of schematically guiding the new product development process in companies with unprecedented efficiency.

This study is on the conception of the DS700 HYBRID project by the application of the Industrial Design Structure method (IDeS), which applies different tools sourced from engineering and style departments, including QFD and SDE, used to create the concept of a hybrid motorbike that could reach the market in the near future. SDE is an engineering approach for the design and development of industrial design projects, and it finds important applications in the automotive sector. In addition, analysis tools such as QFD, comprising benchmarking and top-flop analysis are carried out to maximize the creative process. The key characteristics of the bike and the degree of innovation are identified and outlined, the market segment is identified, and the stylistic trends that are most suitable for a naked motorbike of the future are analyzed. In the second part the styling of each superstructure and of all the components of the vehicle is carried out. Afterwards the aesthetics and engineering perspectives are accounted for to complete the project. This is achieved with modelling and computing tools such as 3D CAD, visual renderings, and FEM simulations, and virtual prototyping thanks to augmented reality (AR), and finally physical prototyping with the use of additive manufacturing (AM). The result is a product conception able to compete in the present challenging market, with a design that is technically feasible and also reaches new lightness targets for efficiency.

Torsional deformities of the lower limb are common in children with cerebral palsy (CP)-determining gait problems. The mechanisms underlying transverse plane gait deviations arise from a combination of dynamic and static factors. The dynamic elements may be due to spasticity, contractures and muscle imbalances, while the static ones may result from excessive femoral anteversion, which decreases the efficiency of the hip abductors by reducing the muscular lever arms. A therapeutic approach has been identified in multi-level functional surgery for the lower limb. Treating the malalignments of the lower limb with femoral or tibial derotation provides optimal results, especially when supported by adequate biomechanical planning. This planning requires an integrated static-dynamic approach of morphological and functional evaluation, based on radiological measurements, physical examination and gait analysis. Instrumented gait analysis has been confirmed as essential in the evaluation and surgical decision making process for children affected by CP with transverse plane deformities. Computational simulations based on musculoskeletal models that integrate patient-specific CT morphological data into gait analysis can be used for the implementation of a surgical simulation system in pre-operative planning to test the possible effects of the different surgical treatment options on the torsional defects of the lower limbs. Recently, a computer-aided simulation process has been implemented in the preoperative planning of complex osteotomies for limb deformities in children. Three-dimensional (3D) digital models were generated from Computed Tomography (CT) scans, using free open-source software. The aim of this study is to integrate the patient-specific CT musculoskeletal model with morphological data and gait analysis data, with the personalized calculation of kinematic and kinetic parameters, which allow us to generate an “avatar” of the patient for a more in-depth evaluation of the gait abnormalities. The computational simulation platform proposed provides a realistic movable musculoskeletal model in a virtual environment, with the possibility of planning and monitoring the effects of virtual three-dimensional surgical corrections.

In this paper, industrial design structure (IDeS) is applied for the development of two new full-electric sports sedan car proposals that go by the names Blitz Vision AS and Retro. With a deep analysis of the trends dominating the automotive industry, a series of product requirements was identified using quality function deployment (QFD). The results of such analysis led to the definition of the technical specifications of the product via benchmarking (BM) and top-flop analysis (TFA). The product architecture was then defined by making use of a modular platform chassis capable of housing a variety of vehicle bodyworks. The structured methodology of stylistic design engineering (SDE) was used. This can be divided in six phases: (1) stylistic trends analysis; (2) sketches; (3) 2D CAD drawings; (4) 3D CAD models; (5) virtual prototyping; (6) solid stylistic model. The chassis of the CAD model was verified structurally by means of FEM analysis, whereas the drag coefficients of the two vehicle proposals were compared with one of the main competitor’s vehicles via CFD simulations. The resulting car models are both aesthetically appealing and can be further developed, leading eventually to the production stage. This proves the effectiveness of IDeS and SDE in car design.

The present study was set to validate two different suburban-type sportscar bodies with shared common underpinnings. The chosen method to develop this project was the Industrial Design Structure (IDeS), which characterizes the ability to use the different innovative techniques known within the industrial field, across the whole organization. This method is embodied by following a series of structured analysis tools, such as QFD (Quality Function Deployment), Benchmarking (BM), Top-Flop analysis (TFA), Stylistic Design Engineering (SDE), Prototyping, Testing, Budgeting and Planning. This project aims to study the present-day car market and to foresee deployment in the near future. This attempt was confirmed by delivering the complete styling and technical feasibility characteristics of two different sports cars, obtained by the IDeS methodology. This approach of embodying design together with phases of product development would provide a better engineered, target-oriented product, that uses state-of-the-art style and CAD environments to reduce product development time and, hence, overall Time to Market (TTM).

The following case study portrays the several steps required to conceive a product from scratch. The first step involves an in-depth analysis of today’s electric bicycle market in order to obtain data and information relating to the levels of innovation and comfort required by customers. Then, we evaluate the implementation of a useful method to understand the level of innovation that the product must have to be competitive on the market. The second part studies the architecture of the product, considering the different components already sold on the market which will become part of the project. The third part concerns a comparison between different stylistic trends that the vehicle may have (in order to outline the best one). The fourth part concerns the CAD realization of the virtual model complete with all its parts, including a structural verification study of the frame. The last part studies the presentation of the product to the customer, exploring different effective ways to communicate what the strengths of the new product will be (also allowing them to customize it before its realization). The plan for the realization of the new product, starting from the concept to arrive at the final presentation to the customer, follows the methods proposed by applying a series of steps to develop a generic new product in an efficient, sensible, and methodical manner. Therefore, we will refer to quality function deployment (QFD), benchmarking (BM), design for X, until reaching the final prototyping and testing phases.

The evolution of innovative and systematic design methodologies over time has widened the design concept involvement from the product development phase, which also includes the production and start-up phases. Literature findings have presented to accomplish a Generative Design (GD) approach through the application of an innovative method called Industrial Structure Design (IDeS), a systematic design method able to discover the customer’s needs and the fundamental technical solutions to obtain a good innovative product, involving the whole organization for this achievement. Nevertheless, there is a social demand for solutions to the dramatic and growing problem of marine pollution from plastic materials, encouraging the designers to conceive a new innovative drone for waste collection at sea. Therefore, this study aims to merge all the most advanced design technologies with IDeS in an integrated way, by generating a structure that can also be adopted to plan the organization of a production company. The approach is validated with the design of the Recovery Plastic Drone (RPD) obtained with the IDeS methodology, combining Design and Product development phases, leading to a better and innovative solution for the market.

Improvements in software for image analysis have enabled advances in both medical and engineering industries, including the use of medical analysis tools to recreate internal parts of the human body accurately. A research analysis found that FDM-sourced elements have shown viability for a customized and reliable approach in the orthopedics field. Three-dimensional printing has allowed enhanced accuracy of preoperative planning, leading to reduced surgery times, fewer unnecessary tissue perforations, and fewer healing complications. Furthermore, using custom tools chosen for each procedure has shown the best results. Bone correction-related surgeries require customized cutting guides for a greater outcome. This study aims to assess the biopolymer-based tools for surgical operations and their ability to sustain a regular heat-sterilization cycle without compromising the geometry and fit characteristics for a proper procedure. To achieve this, a DICOM and FDM methodology is proposed for fast prototyping of the cutting guide by means of 3D engineering. A sterilization test was performed on HTPLA, PLA, and nylon polymers. As a result, the unique characteristics within the regular autoclave sterilization process allowed regular supplied PLA to show there were no significant deformations, whilst annealed HTPLA proved this material’s capability of sustaining repeated heat cycles due to its crystallization properties. Both of these proved that the sterilization procedures do not compromise the reliability of the part, nor the safety of the procedure. Therefore, prototypes made with a similar process as this proposal could be safely used in actual surgery practices, while nylon performed poorly because of its hygroscopic properties.

Additive manufacturing processes have evolved considerably in the past years, growing into a wide range of products through the use of different materials depending on its application sectors. Nevertheless, the fused deposition modelling (FDM) technique has proven to be an economically feasible process turning additive manufacture technologies from consumer production into a mainstream manufacturing technique. Current advances in the finite element method (FEM) and the computer-aided engineering (CAE) technology are unable to study three-dimensional (3D) printed models, since the final result is highly dependent on processing and environment parameters. Because of that, an in-depth understanding of the printed geometrical mesostructure is needed to extend FEM applications. This study aims to generate a homogeneous structural element that accurately represents the behavior of FDM-processed materials, by means of a representative volume element (RVE). The homogenization summarizes the main mechanical characteristics of the actual 3D printed structure, opening new analysis and optimization procedures. Moreover, the linear RVE results can be used to further analyze the in-deep behavior of the FDM unit cell. Therefore, industries could perform a feasible engineering analysis of the final printed elements, allowing the FDM technology to become a mainstream, low-cost manufacturing process in the near future.

Fused Deposition Modeling (FDM) 3D printing is the most widespread technology in additive manufacturing worldwide that thanks to its low costs, finished component applications, and the production process of other parts. The need for lighter and higher-performance components has led to an increased usage of polymeric matrix composites in many fields ranging from automotive to aerospace. The molds used to manufacture these components are made with different technologies, depending on the number of pieces to be made. Usually, they are fiberglass molds with a thin layer of gelcoat to lower the surface roughness and obtain a smooth final surface of the component. Alternatively, they are made from metal, thus making a single carbon fiber prototype very expensive due to the mold build. Making the mold using FDM technology can be a smart solution to reduce costs, but due to the layer deposition process, the roughness is quite high. The surface can be improved by reducing the layer height, but it is still not possible to reach the same degree of surface finish of metallic or gelcoat molds without the use of fillers. Thermoplastic polymers, also used in the FDM process, are generally soluble in specific solvents. This aspect can be exploited to perform chemical smoothing of the external surface of a component. The combination of FDM and chemical smoothing can be a solution to produce low-cost molds with a very good surface finish.

This study shows an application of the Design for Six Sigma (DFSS) Methodology in the field of medical engineering. This research aims to demonstrate the application of a systematic design approach in the development of the “Ocane”, an innovative concept of smart cane for visually impaired patients which was thought of in answer to the end user’s needs, deploying an easy to transport, locate, and adjust element with ultrasonic sensors and tactile feedback. DFSS is an analytical design methodology meant to organize project workflow in a sequence of specific steps. Other standardized design procedures such as Quality Function Deployment (QFD) and Stylistic Design Engineering (SDE) have been used to support DFSS in terms of targeting customer requirements and focusing on aesthetics for ergonomics analysis, respectively. First, the QFD process is introduced and applied to gather the final customer needs, completing the analysis with benchmarking and similar-thought products on the market. Afterwards, a description of the DFSS methodology and application to the case study was deployed. Thereafter, the SDE procedure is exposed by identifying the “Ocane” concept and development, and moving towards the completion of an inventive product with a creative design and careful attention to visually impaired clients’ requirements.

The design of an E segment, executive, midsize sedan car was chosen to fill a gap in the market of the Ford brand and to achieve the goal of innovation looking towards the future. Ford has not owned an E-segment flagship sports sedan for years, since the historic 1960s Falcon. Starting from the latter assumption and considering that the major car manufacturers are currently investing heavily in E-segment cars, it is important to design a new model, which has been called the Eagle. This model proposed here is to fill the gap between Ford and other companies that are already producing sport cars for the electric sector and to complete Ford’s proposal. The presented methodology is based on SDE, on which many design tools are implemented, such as Quality Function Deployment (QFD), Benchmarking (BM), and Top Flop Analysis (TPA). A market analysis follows in order to identify the major competitors and their key characteristics considering style and technology. The results are used to design an innovative car. Based on the most developed stylistic trends, the vehicle is first sketched and then drawn in the 2D and 3D environments for prototyping. This result leads to the possibility of 3D printing the actual model as a maquette using the Fused Deposition Modelling (FDM) technology and testing it in different configurations in Augmented Reality (AR). These two final applications unveil the possibilities of Industry 4.0 as enrichment for SDE and in general rapid prototyping.

Technology evolution and wide research attention on 3D printing efficiency and processes have given the prompt need to reach an understanding about each technique’s prowess to deliver superior quality levels whilst showing an economical and process viability to become mainstream. Studies in the field have struggled to predict the singularities that arise during most Fused Deposition Modeling (FDM) practices; therefore, diverse individual description of the parameters have been performed, but a relationship study between them has not yet assessed. The proposed study lays the main defects caused by a selection of printing parameters which might vary layer slicing, then influencing the defect rate. Subsequently, the chosen technique for optimization is presented, with evidence of its application viability that suggests that a quality advance would be gathered with such. The results would help in making the FDM process become a reliable process that could also be used for industry manufacturing besides prototyping purposes.

Three-dimensional printed custom cutting guides (CCGs) are becoming more and more investigated in medical literature, as a patient-specific approach is often desired and very much needed in today’s surgical practice. Three-dimensional printing applications and computer-aided surgical simulations (CASS) allow for meticulous preoperatory planning and substantial reductions of operating time and risk of human error. However, several limitations seem to slow the large-scale adoption of 3D printed CCGs. CAD designing and 3D printing skills are inevitably needed to develop workflow and address the study; therefore, hospitals are pushed to include third-party collaboration, from highly specialized medical centers to industrial engineering companies, thus increasing the time and cost of labor. The aim of this study was to move towards the feasibility of an in-house, low-cost CCG 3D printing methodology for pediatric orthopedic (PO) surgery. The prototype of a femoral cutting guide was developed for its application at the IOR—Rizzoli Orthopedic Institute of Bologna. The element was printed with an entry-level 3D printer with a high-temperature PLA fiber, whose thermomechanical properties can withstand common steam heat sterilization without bending or losing the original geometry. This methodology allowed for extensive preoperatory planning that would likewise reduce the overall surgery time, whilst reducing the risks related to the intervention.

This experimental study defines the usage of a computer-aided surgical simulation process that is effective, safe, user-friendly, and low-cost, that achieves a detailed and realistic representation of the anatomical region of interest. The chosen tools for this purpose are state-of-the-art Computer Aided Design (CAD) software for mechanical design, and are the fundamental application dedicated to parametric modeling. These tools support different work environments, each one is for a specific type of modeling, and they allow the simulation of surgery. The result will be a faithful representation of the anatomical part both before and after the surgical procedure, screening all the intermediate phases. The doctor will assess different lines of action according to the results, then he will communicate them to the engineer who, consequently, will correct the antisymmetric issue and regenerate the model. Exact measurements of the mutual positions of the various components, skeletal and synthetic, can be achieved; all the osteosynthesis tools, necessary for the surgeon, can be included in the project according to different types of fracture to perfectly match the morphology of the bone to be treated. The method has been tested on seven clinical cases of different complexity and nature and the results of the simulations have been found to be of great effectiveness in the phase of diagnosis and of preoperative planning for the doctors and surgeons; therefore, allowing a lower risk medical operation with a better outcome. This work delivers experimental results in line with theoretical research findings in detail; moreover, full experimental and/or methodical details are provided, so that outcomes could be obtained.

The study of CAD (computer aided design) modeling, design and manufacturing techniques has undergone a rapid growth over the past decades. In medicine, this development mainly concerned the dental and maxillofacial sectors. Significant progress has also been made in orthopedics with pre-operative CAD simulations, printing of bone models and production of patient-specific instruments. However, the traditional procedure that formulates the surgical plan based exclusively on two-dimensional images and interventions performed without the aid of specific instruments for the patient and is currently the most used surgical technique. The production of custom-made tools for the patient, in fact, is often expensive and its use is limited to a few hospitals. The purpose of this study is to show an innovative and cost-effective procedure aimed at prototyping a custom-made surgical guide for address the cubitus varus deformity on a pediatric patient. The cutting guides were obtained through an additive manufacturing process that starts from the 3D digital model of the patient’s bone and allows to design specific models using Creo Parametric. The result is a tool that adheres perfectly to the patient’s bone and guides the surgeon during the osteotomy procedure. The low cost of the methodology described makes it worth noticing by any health institution.

The present study aims to validate a new research method called IDeS (industrial design structure) through the design of an electric bicycle for everyday city life. IDeS is the latest evolution of a combination of innovative and advanced systematic approaches that are used to set a new industrial project. The IDeS methodology is sequentially composed of quality function deployment (QFD), benchmarking (BM), top-flop analysis (TFA), stylistic design engineering (SDE), design for X, prototyping and testing, budgeting, and planning. The present work illustrates how to integrate the abovementioned design methods and achieve a convincing result. In going through the IDeS method step by step, we compare the different solutions on the market in order to understand which are the best performing products and to understand what is missing on the market. This method allowed us to design a bicycle that is as close as possible to the “ideal bike”, obtained with the top/flop analysis.

The work carried out has the purpose of improving and optimizing various industrial technical operations, such as preventive maintenance, taken here as an example of application, using the Design for Disassembly (DfD) technique. Therefore, through four metaheuristic methods that have been chosen among the most widespread in the field (described below) to make a comparison between them, the optimal disassembly sequence is sought, if it exists, in terms of time and then costs in order to extract a target component without damaging the other mechanical parts of the assembly. The hypothesis that has been tested throughout this case study is “a responsible application of DfD, not only from the design process of a product but also during the disassembly procedure, can bring substantial benefits to the company”. Interaction with a hypothetical operator in charge of the work to be performed is implemented with the use of augmented reality. In fact, through an application programmed for an Android device (in this case, a mobile phone, hence a handheld device), the operator can be instructed step-by-step on the disassembly sequence in dynamics as an animation. Finally, two virtual buttons were added in augmented reality with which the operator can start and pause/resume the animation at any time to facilitate the understanding of the different steps established by the sequence.

Environmental impact and recycling have been increasingly frequent topics in recent years. At the same time, the life cycle of products has increasingly become shorter, as the escalating competitive market requires new products in smaller pieces. From this perspective, the recovery of parts and products that are produced in this market system for subsequent reuse when they reach the end of their life cycle is essential. For these reasons, it has become critical that companies re-evaluate their product design with a view to the possible recovery of the parts that comprise their products and to create new products for the market. The following discussion was based on the study of design for disassembly (DfD), which is the analysis of industrial products aimed at optimizing disassembly in terms of time and costs. The application of the DfD to a case study of a gearbox has, among its main objectives, the search for the best disassembly sequence in terms of time and money. During the course of the study, augmented reality (AR) was used. Through the use of the Unity software and Vuforia package, it was possible to bring the gearbox back to AR and then simulate the disassembly sequence in AR.

The work here described aims to offer a starting point for improving and making a generic maintenance process more efficient, first of all thanks to the use of a cutting-edge technology such as augmented reality, as a key tool that makes it possible and immediate to communicate to operators which are the fundamental stages of the maintenance process to be followed in the working area. Furthermore, thanks to the use of two methods applied in the context of the Design for Disassembly (later described), we also propose to search for all the possible sequences to get to the removal of a target component to be adjusted—in particular the optimal one (if it exists, in terms of time and costs) to be subsequently applied in an augmented reality “self-disassembly” model that can be viewed and followed by the operator, in a way that is still very little used today.

In this work, a structured design method, the Stylistic Design Engineering (SDE), is applied for the construction of a new minivan car, in particular a new city car, which we will call FIAT 600 Omega. The SDE, or Stylistic Design Engineering, is a structured engineering method for carrying out automotive design projects. The SDE method consists of six different phases: (1) Analysis of stylistic trends; (2) Sketches; (3) 2D Computer Aided Design (CAD) drawings; (4) 3D CAD models; (5) Rendering; (6) Solid stylistic model (also called style maquette). This project deals with the external redesign of the Fiat 600 multiple, a small minivan which was very successful in the 1950s and 1960s. SDE is a methodology consisting of various technologies and design methodologies that will be further explained in detail, such as the Pininfarina method, the Quality Function Deployment (QFD) method, Benchmarking (BM), and Top Flop Analysis (TPA). The work was organized according to the different phases. Initially, the Fiat style was studied, in particular the style of the FIAT 600 MULTI PURPOUSE VEHICLE (MPV). This step is essential to better understand the characteristics of the brand and also the main characteristics carried out over the decades. Then we moved on to the freehand sketching phase, based on what we learned in the previous phase of the study. When a satisfactory shape was found for the new car, by analyzing and discarding the different proposals of the various types of style, we proceeded to the evaluation of the proportions and dimensions through two-dimensional drawings and finally we obtained the three-dimensional shape of the new car thanks to 3D CAD software and rendering software. Many advantages in the industrial world SDE takes together with its development. In fact, until the early 2000s, car design and styling was considered quite a craft activity, not a technical or scientific one, mostly based on the great capability of famous car designers and masters, just like Giugiaro, Zagato, Bertone, Pininfarina, Stephenson, Bangle, etc. Then, thanks to the industrial activity of Eng. Lorenzo Ramacciotti, former CEO of Pininfarina Spa and Mechanical Engineer, and also thanks to the academic studies developed at ALMA MATER STUDIORUM University of Bologna, SDE became the object of attention, because it is able to systematize the car design process and reduce costs. With SDE, a good design research or an industrial product development team can complete a car design project, also without the presence of a mentor. Car Design Process finally becomes with SDE a scientific method; Car Design becomes with SDE an industrial method. Industrial needs are nice products made in a short time; SDE is structured to attend these issues. Industrial challenges follow innovation, in shape and functionality; SDE is able to recognize innovation. Industrial benefits can be reached with SDE, ensuring beautiful aesthetic projects are realized systematically and with low costs.

This work aims to analyze the characteristics and importance that design techniques for disassembly assume in the modern design phase of a mechanism. To this end, the study begins by considering a three-dimensional model of a gear motor, taken from the components of which the overall drawings are arranged and from the relief of those not available. Once the mechanism has been digitally reconstructed, the activity focuses on the study of the optimal disassembly sequence by comparing different methodologies, according to two evaluation criteria—minimizing the time taken and minimizing the number of tool changes necessary to complete the sequence. The main results of the work are (1) defining a standard methodology to improve disassembly sequence planning, (2) finding the best disassembly sequence for the specific component among the literature and eventually new methods, and (3) offering to the industrial world a way to optimize maintenance operations in mechanical products. Referring to the limitation of the present works, it can be affirmed that the results are limited to the literature explored and to the case study examined.

This work aims to present an in-house low-cost computer-aided simulation (CASS) process that was recently implemented in the preoperative planning of complex osteotomies for limb deformities in children. Five patients admitted to the Unit of Paediatric Orthopaedics and Traumatology from April 2018 to December 2019, for correcting congenital or post-traumatic limb deformities were included in the study. Three-dimensional (3D) digital models were generated from Computed Tomography (CT) scans, using free open-source software, and the surgery was planned and simulated starting from the 3D digital model. 3D printed sterilizable models were fabricated using a low-cost 3D printer, and animations of the operation were generated with the aim to accurately explain the operation to parents. All procedures were successfully planned using our CASS method and the 3D printed models were used during the operation, improving the understanding of the severely abnormal bony anatomy. The surgery was precisely reproduced according to CASS and the deformities were successfully corrected in four cases, while in one case, the intraoperative intentional undersizing of the bone osteotomy produced an incomplete correction of a congenital forearm deformity. Our study describes the application of a safe, effective, user-friendly, and low-cost CASS process in paediatric orthopaedics (PO) surgery. We are convinced that our study will stimulate the widespread adoption of this technological innovation in routine clinical practice for the treatment of rare congenital and post-traumatic limb deformities during childhood.

The present study wants to bring to light a new type of crutch designed for a chronic patient with perennial limited mobility, who must use this support every time a move is needed. The main purpose of the project consists in recommending a correct use of the crutch through technology, limiting the damage normally caused by a bad use of crutches and giving a support both for the patient and for the doctor. All of the features of the crutches were defined through relationship matrices and a benchmarking, which helped us for defining the requirements; other important features were defined, taking a look to the technological progresses applied to new, patented crutches. The result is a sensorized crutch, functional and oriented to meet the user’s needs in order to prevent an incorrect use of the support avoiding the growth of other pains.

This paper presents a a novel alghorithm of diagnosis and treatment of rigid flatfoot due to tarsal coalition. It introduces a workflow based on 3D printed models, that ensures more efficiency, not only by reducing costs and time, but also by improving procedures in the preoperative clinical phase. Since this paper concerns the development of a new methodology that integrates both engineering and medical fields, it highlights symmetry. An economic comparison is made between the traditional method and the innovative one; the results demonstrate a reduction in costs with the latter. The current, traditional method faces critical issues in diagnosing the pathologies of a limb (such as the foot) and taking decisions for further treatment of the same limb. The proposed alternative methodology thus uses new technologies that are part of the traditional workflow, only replacing the most obsolete ones. In fact, it is increasingly becoming necessary to introduce new technologies in orthopedics, as in other areas of medicine, to offer improved healthcare services for patients. Similar clinical treatments can be performed using the aforementioned technologies, offering greater effectiveness, more simplicity of approach, shorter times, and lower costs. An important technology that fits into this proposed methodology is 3D printing.

Recently, the approach that defines the total life cycle assessment (LCA) and the end of life (EoL) in the early design phases is becoming even more promising. Literature evidences many advantages in terms of the saving of costs and time and in the fluent organization of the whole design process. Design for disassembly (DfD) offers the possibility of reducing the time and cost of disassembling a product and accounts for the reusing of parts and of the dismantling of parts, joints, and materials. The sequence of disassembly is the ordered way to extract parts from an assembly and is a focal item in DfD because it can deeply influence times and operations. In this paper, some disassembly sequences are evaluated, and among them, two methods for defining an optimal sequence are provided and tested on a case study of a mechanical assembly. A further sequence of disassembly is provided by the authors based on experience and personal knowledge. All three are analyzed by the disassembly order graph (DOG) approach and compared. The operations evaluated have been converted in time using time measurement units (TMUs). As result, the best sequence has been highlighted in order to define a structured and efficient disassembly.

The primary purpose of this work is to organize, in the best possible way, the design of an ecological transport vehicle, using an advanced design methodology, namely design for six sigma (DFSS). The DFSS is indeed a design approach, able to implement, in a logical and integrated way, other advanced methodologies of systematic design, such as quality function deployment (QFD), TRIZ (in Russian, Teorija Rešenija Izobretatel’skich Zadač), benchmarking, top-flop analysis and others, in order to propose design solutions oriented both to quality and innovation, for satisfying customers. The above described has been demonstrated through the application of DFSS to a case study in which the set up phase of an industrial project was completed, without having overlooked any aspect useful for obtaining a new attractive product. The case study concerns the application of DFSS to a new low-polluting motorcycle. At the end of the work, the designer obtained the achievement of the conceptual project.

Today’s market drives companies to change, adapt, and compete. Many consumers are increasingly looking at price, without sacrificing quality. In order to be attractive to the customer, companies must be able to offer the required quality at the lowest possible price. The life cycle of many products has been shortened compared to the past because now technologies are evolving faster. For these reasons, it is important that companies reevaluate all the operations that are carried out within them, to optimize them and eventually adopt new technologies if they offer interesting opportunities. In this discussion, we first study the design for disassembly, a technique that can bring several advantages during the life cycle of a component, offering the possibility of reducing time and cost of disassembling a product, and better reuse of the different materials of which it is composed. Subsequently, augmented reality is discussed, and how this technology is exploited in the world, especially in the industrial sector. During the work, we discuss a case study, with the gearbox being the object of analysis. This allows us to apply the theoretical concepts illustrated in a concrete way, allowing for a better understanding of the topics.

Our purpose is to develop the preoperative diagnosis stage for orthopedic surgical treatments using additive manufacturing technology. Our methods involve fast implementations of an additive manufactured bone model, converted from CAT data, through appropriate software use. Then, additive manufacturing of the formed surfaces through special 3D-printers. With the structural model redesigned and printed in three dimensions, the surgeon is able to look at the printed bone and he can handle it because the model perfectly reproduces the real one upon which he will operate. We found that additive manufacturing models can precisely characterize the anatomical structures of fractures or lesions. The studied practice helps the surgeon to provide a complete preoperative valuation and a correct surgery, with minimized duration and risks. This structural model is also an effective device for communication between doctor and patient.

This paper presents the application of a low-cost 3D printing technology in pre-operative planning and intra-operative decision-making. Starting from Computed Tomography (CT) scans, we were able to reconstruct a 3D model of the area of interest with a very simple and rapid workflow, using open-source software and an entry level 3D printer. The use of High Temperature Poly-Lactic Acid (HTPLA) by ProtoPasta allowed fabricating sterilizable models, which could be used within the surgical field. We believe that our method is an appealing alternative to high-end commercial products, being superior for cost and speed of production. It could be advantageous especially for small and less affluent hospitals that could produce customized sterilizable tools with little investment and high versatility.

Considering the progressively expansive trade world, “time to market„ of productions and goods has turned into a key element for business accomplishment. There are diverse practices that antedate design faults and unveil products on the market in minus time. Among the most used methods in the design and explanation of the necessities, quality function deployment (QFD) and design for Six Sigma (DFSS) can be used. In the prototyping stage, it is probable to address the emergent technology of additive manufacturing. Today, 3D printing is employed as a quick prototyping technique. Nevertheless, the tangible task which industry is fronting is the adoption of these machines for large-scale production of components, which is now possible with new HP multi fusion. The goal of this paper is to illustrate the entire product development process taking advantage of the most modern models and technologies for the final realization of a case study that involves the design and prototyping of an innovative multifunctional fan (lamp, aroma diffuser, and fan) through the multi jet fusion of HP. To begin with, issues related to the DFSS, the QFD and their application to identify the fan requirements are explored. Once the requirements have been defined, the modern CAD design systems and the CAE systems for the validation of the case study will be analyzed and applied. Finally, HP’s multi jet fusion methodology and design rules for additive manufacturing will be analyzed in detail, trying to exploit all the positive aspects it offers.

The aim of this article is to apply some design methodologies to define, as a first objective, an optimized technical specification and then, as a second objective, to manage the transition from conceptual design to construction project of an innovative means of urban transport, meeting the needs of ‘renewable energy’ requirements, which then decline into this new urban vehicle formed by a hoverboard and an electric scooter. The first part of the article is focused on the conceptual design of the means by using methodologies such as the Quality Function Deployment (QFD), applied in the first phase of the work to compare some of the most popular electric scooters on the market; we then used a typical method for product marketing, i.e., the decision-making process driven by the analysis of benchmarking, suitable for quantitatively organize competitive analysis and choosing innovation targets; finally, we implemented the top-flop analysis in order to better improve the benchmarking implementation, identifying the best product on the market, basing on the highest number of innovative requirements owned by it, as shown by Frizziero in 2018 and Meuli et al. in 1997. The second part of the article focuses on the project of the kick scooter through the use of a software for the FEA simulation and on the possible realization of the prototype through a suitable connecting component.