Search

Two integrated harvesting methods have been primarily applied to increase the opportunity for forest biomass utilization. In Korea, small shovels with a carrier for cut-to-length harvesting (CTL system) and tower yarders for whole-tree harvesting (WT system) are commonly used for the transportation of tree assortments (i.e., sawlogs and logging residue). No previous studies are available in South Korea that have compared and highlighted the operational performance and yield of logging residues between the CTL and WT harvesting systems. Thus, our study’s main objectives were to (1) evaluate the productivity and costs of the two harvesting systems through a standard time study method and (2) estimate the amount of harvesting logging residue at the landing. The productivities of the CTL and WT systems were 1.45 and 2.99 oven-dried tons (odt)/productive machine hour (PMH), at a cost of 86.81 and 45.41 USD/odt, respectively. In the WT system, the amount of logging residue (2.1 odt/ha) collected at the landing was approximately four-times larger than that of the CTL system (0.5 odt/ha). Our results suggested that the WT system is a less expensive and more suitable system when there are markets demanding logs and biomass, whereas the CTL system remains a less expensive option for stem-only harvesting. Furthermore, these results are important for estimating the economic and environmental amount of residue that could be potentially recovered and utilized from the forest types included in the study.

In Korean residential buildings, floor impact sounds were reduced over the past few decades mainly through a floating floor system. However, ceiling constructions for impact sound reduction have not been applied actively because of a lack of useful information. This study focuses on the effects of wall-to-wall supported ceilings (WSC), which are designed with construction discontinuities between concrete slabs and ceilings, and the damping caused by porous absorbers for impact sound insulation. To examine the impact sound insulation according to ceiling conditions, measurements were performed in 25 floor–ceiling assemblies. The results indicate that ceiling treatment is mostly useful in reducing the floor impact sound. The floor impact sound owing to the WSC decreased by 2–7 dB and 2–8 dB in terms of the single number quantity for the tapping machine and rubber balls, respectively, compared with representative existing housing constructions wherein ceilings were attached on wooden sticks. Furthermore, the reduction effect of the WSC appeared to be more profound when it was applied to the floor–ceiling assembly with poor impact sound insulation. Thus, the WSC can be used to enhance the impact of sound insulation of existing housings without major repairs of floor structural layers.

Selective laser sintering of metal nanoparticle ink is an attractive technology for the creation of metal layers at the microscale without any vacuum deposition process, yet its application to elastomer substrates has remained a highly challenging task. To address this issue, we introduced the shear-assisted laser transfer of metal nanoparticle ink by utilizing the difference in thermal expansion coefficients between the elastomer and the target metal electrode. The laser was focused and scanned across the absorbing metal nanoparticle ink layer that was in conformal contact with the elastomer with a high thermal expansion coefficient. The resultant shear stress at the interface assists the selective transfer of the sintered metal nanoparticle layer. We expect that the proposed method can be a competent fabrication route for a transparent conductor on elastomer substrates.

In Korea, water supply and drainage noises result in one of the main noise complaints because more than 50% of people reside in multi-residential buildings. In this study, a series of field measurements were therefore carried out to examine the current noise situation. The noise levels were measured in the bathrooms of the upper and lower floors, as well as in habitable rooms. The measurement results for the bathrooms of the lower floor (N = 113) are 47.8 dBA (water closet), 42.7 dBA (basin), and 33.9 dBA (bathtub) for water drainage, while values vary between 33.7 dBA and 37.0 dBA for the water supply. The results suggest that the water drainage noise needs to be controlled first. The system bathroom (42.8 dBA) produced lower noise levels than the wet construction method (48.2 dBA) for all of the sanitary wares. The highest noise levels in the living rooms (N = 11) and bedrooms (N = 8) of the lower floor are 34.3 dBA and 39.1 dBA, respectively. The average noise level in the rooms (N = 19) is 37.8 dBA. The overall result suggests that it is necessary to develop an acoustic guideline to satisfy the higher Class of the 2nd ISO/CD 19488, although the current noise level satisfies Class C (living room) and Class D (bedroom).

To date, solar energy generation devices have been widely studied to meet a clean and sustainable energy source. Among them, water splitting photoelectrochemical cell is regarded as a promising energy generation way for splitting water molecules and generating hydrogen by sunlight. While many nanostructured metal oxides are considered as a candidate, most of them have an improper bandgap structure lowering energy transition efficiency. Herein, we introduce a novel wet-based, successive photoreduction process that can improve charge transfer efficiency by surface plasmon effect for a solar-driven water splitting device. The proposed process enables to fabricate ZnO/CuO/Ag or ZnO/CuO/Au hierarchical nanostructure, having an enhanced electrical, optical, photoelectrochemical property. The fabricated hierarchical nanostructures are demonstrated as a photocathode in the photoelectrochemical cell and characterized by using various analytic tools.