Search

The effect of the swirl clocking on three-dimensional nozzle guide vane (NGV) is investigated using computational fluid dynamics. The research reports the loss characteristics of leaned and swept NGVs and the influence of swirl clocking. The three-dimensional NGVs are built by stacking the same 2D profile along different linear axes, characterized by different angles with respect to the normal or radial direction: ε = −12° ~ +12° for the leaned and γ = −5° ~ +10° for the swept airfoils. A total of 40 models are analyzed to study the effects of lean and sweep on aerodynamic performance. To investigate the influence of swirl clocking, the analysis cases include the center of the swirl that was positioned at the leading edge as well as the middle of the passage. The prediction results show that the relationship of the changes in mass flow rate and throat area are not monotonic. Further observation confirms the redistribution of loading and flow angle under different lean and sweep angles; thus, three-dimensional design is a key influencing factor on aerodynamic performance. In the presence of swirl clocking, NGV performance is changed significantly and the findings offer new insight and opportunities to improve three-dimensional NGV airfoil design.

The influence of film-hole position on internal and external heat transfer was investigated using Computational Fluid Dynamics (CFD). A simplified geometry of an integrated configuration of a ribbed channel, film hole and mainstream passage is modeled to represent a turbine internal and external cooling scheme. The proposed configurations with nine different positions of film holes are parameterized to conduct a series of CFD calculations at a target blowing ratio of 0.8, 1.1 and 1.7. Since the present study is taking a comparative approach, CFX with SST models is applied as a primary tool and the results are compared with Fluent solver for selected cases (total 36 cases). Among the proposed nine positions, the film holes located in the separated flow region of a ribbed channel showed considerable enhancement in film effectiveness with minimum reduction and potential improvement in internal heat transfer. The finding offers a design opportunity to enhance internal as well as external heat transfer.

Turbine generators operate with complex cooling systems due to the challenge in controlling the peak temperature of the stator bar caused by Ohm loss, which is unavoidable. Therefore, it is important to characterize and quantify the thermal performance of the cooling system. The focus of the present research is to investigate the heat transfer and pressure loss characteristics of a typical cooling system, the so-called stator ventilation duct. A real scale model was built at its operating conditions for the present study. The direction of cooling air was varied to consider its operation condition, so that there are: (1) outward flow; and (2) inward flow cases. In addition, the effect of (3) cross flow (inward with cross flow case) was also studied. The transient heat transfer method using thermochromic liquid crystals is implemented to measure full surface heat transfer distribution. A series of computational fluid dynamics (CFD) analyses were also conducted to support the observation from the experiment. For the outward flow case, the results suggest that the average Nusselt numbers of the 2nd and 3rd ducts are at maximum 100% and 30% higher, respectively, than the inward flow case. The trend was similar with the effect of cross flow. The CFD results were in good agreement with the experimental data.

A 3.0 Gsymbol/s/lane receiver is proposed herein to acquire near-grounded high-speed signals for the mobile industry processor interface (MIPI) C-PHY version 1.1 specification used for CMOS image sensor interfaces. Adaptive level-dependent equalization is also proposed to improve the signal integrity of the high-speed receivers receiving three-level signals. The proposed adaptive level-dependent equalizer (ALDE) is optimized by adjusting the duty cycle ratio of the clock recovered from the received data to 50%. A pre-determined data pattern transmitted from a MIPI C-PHY transmitter is established to perform the adaptive level-dependent equalization. The proposed MIPI C-PHY receiver with three data lanes is implemented using a 65 nm CMOS process with a 1.2 V supply voltage. The power consumption and area of each lane are 4.9 mW/Gsymbol/s/lane and 0.097 mm2, respectively. The proposed ALDE improves the peak-to-peak time jitter of 12 ps and 34 ps, respectively, for the received data and the recovered clock at a symbol rate of 3 Gsymbol/s/lane. Additionally, the duty cycle ratio of the recovered clock is improved from 42.8% to 48.3%.