Search

Pigs are the most common amplifying hosts of the Japanese encephalitis virus (JEV). In 2016, four residents on Tsushima Island who did not own pig farms were diagnosed with JE. Therefore, a serosurvey was conducted to estimate the risk and seroprevalence of JEV after the outbreak. Sera collected from 560 Tsushima Island residents between January and September 2017 were tested for neutralizing antibodies against JEV strains JaGAr01 (genotype 3) and Muar (genotype 5). Sera collected from six wild boars between June and July 2022 were tested. The seroprevalence rates of neutralizing antibodies against JaGAr01 and Muar were 38.8% and 24.6%, respectively. High anti-JEV neutralizing antibody titers of ≥320 were identified in 16 residents, including 3 younger than 6 years with prior JEV vaccination, 2 in their 40s, and 11 older than 70. However, no anti-JEV-specific IgM was detected. Residents who engaged in outdoor activities had higher anti-JEV antibody titers. Sera from wild boars were negative for JEV RNA, but four of six samples contained neutralizing antibodies against JEV. Therefore, JEV transmission continues on Tsushima Island, even in the absence of pig farms, and wild boars might serve as the amplifying hosts.

Aluminum garnets display exceptional adaptability in incorporating mismatching elements, thereby facilitating the synthesis of novel materials with tailored properties. This study explored Ce3+-doped Tb3Al5−xScxO12 crystals (where x ranges from 0.5 to 3.0), revealing a novel approach to control luminescence and photoconversion through atomic size mismatch engineering. Raman spectroscopy confirmed the coexistence of garnet and perovskite phases, with Sc substitution significantly influencing the garnet lattice and induced A1g mode softening up to Sc concentration x = 2.0. The Sc atoms controlled sub-eutectic inclusion formation, creating efficient light scattering centers and unveiling a compositional threshold for octahedral site saturation. This modulation enabled the control of energy transfer dynamics between Ce3+ and Tb3+ ions, enhancing luminescence and mitigating quenching. The Sc admixing process regulated luminous efficacy (LE), color rendering index (CRI), and correlated color temperature (CCT), with adjustments in CRI from 68 to 84 and CCT from 3545 K to 12,958 K. The Ce3+-doped Tb3Al5−xScxO12 crystal (where x = 2.0) achieved the highest LE of 114.6 lm/W and emitted light at a CCT of 4942 K, similar to daylight white. This approach enables the design and development of functional materials with tailored optical properties applicable to lighting technology, persistent phosphors, scintillators, and storage phosphors.

The 3He gas is commonly used for the detection of thermal neutrons. However, with the depletion of 3He gas, there is a need to develop new solid scintillators for thermal neutron detection. Solid scintillators containing 6Li, which have large neutron capture cross-sections and a large amount of energy released by transmutation reactions, are commonly used as alternative candidates. However, only single-crystal scintillators are currently used, and their 6Li concentration is limited by their chemical composition. In this study, we designed, grew, and evaluated a new eutectic scintillator, Rb2CeCl5/LiCl, which can improve the 6Li concentration compared with single-crystal scintillators. Rb2CeCl5, which was selected as the scintillator phase, has excellent scintillator properties (light yield: 36,000 photons/MeV, decay time: mostly 24 ns, slightly 153 ns), and is less deliquescent than other halide scintillators. The crystal grown using the vertical Bridgman method exhibited a eutectic phase composed of Rb2CeCl5 and LiCl. The eutectic crystals exhibited Ce3+ 5d-4f emissions, with a peak between 360 and 370 nm. The Rb2CeCl5 phase was identified as the luminescent phase via cathodoluminescence mapping, and 16,000 photons/neutron of the light yield and 56.1 ns of the decay time were observed. This study indicates that the Rb2CeCl5/LiCl eutectic scintillator is a promising candidate for use in thermal neutron detectors.

β-Ga2O3 is a well-known semiconductor material for power devices and other applications. Recently, β-Ga2O3 has also been reported as a scintillator material with a light yield of approximately 8400 ph./MeV, scintillation decay time of 3. In this study, 45 cm diameter β-Ga2O3 single crystals were prepared via oxide crystal growth using the cold crucible (OCCC) method under various oxygen partial pressures. In the OCCC method, as in the cold crucible method, a high frequency is applied directly to the oxide materials, which are heated and melted, and the melt is held by the outermost solid material itself that is cooled by water using a copper hearth. In the OCCC method, crystal growth is performed while rotating the seed crystal, as in the Czochralski method, to increase the crystal diameter. The optical properties and radiation responses of the crystals grown under various oxygen partial pressures were evaluated.

Background: This study aimed to survey the attitudes toward COVID-19 vaccines and their acceptability among the Japanese public as soon as the United States Food and Drug Administration (FDA) authorized vaccines and their rollouts started around the world. Methods: An anonymous cross-sectional survey was conducted in Japan between 4 January and 5 March 2021. A questionnaire was administered to evaluate attitudes toward COVID-19 vaccines according to demographic characteristics, vaccine characteristics, and vaccine production. Results: A total of 1037 completed responses were received. More than half (63.5%) of the participants responded positively (extremely likely/likely) toward COVID-19 vaccines. The highest acceptance to be vaccinated was discovered among the youngest age group. As expected, participants who had never delayed acceptance or refused the vaccine in their history of vaccination had a significantly higher willingness to be vaccinated against COVID-19 (p < 0.001). Females (OR = 2.66, 95% CI: 1.99–3.58) and participants who had ever delayed acceptance or refuse the vaccine (OR = 3.49, 95% CI: 2.42–5.05) had higher odds of COVID-19 vaccine hesitancy. Participants with a postgraduate degree (OR = 0.64, 95% CI: 0.40–1.00) presented the highest willingness to be vaccinated against COVID-19. More than two-thirds (72.9%, 95% CI: 70.4%–75.8%) of the participants did not mind a booster dose required following primary vaccination. A total of 63.2% (95% CI: 60.0%–66.0%) of the participants only accepted a nearly 90% effective or above vaccine at preventing COVID-19. At the same, 86.4% (95% CI: 84.4%–88.4%) of the participants reported only accepting a vaccine with minor side effects. Conclusions: The moderate levels of COVID-19 vaccine acceptance found in the early phase of the pandemic demonstrate that it is important to improve the implementation of effective management for vaccine promotion and the acceptability of the vaccine to slow or delay transmission.

In recent years, thermal neutron detection using scintillators has been used in a wide range of fields. Thus, the development of scintillators with a higher light yield, faster decay, and higher sensitivity for thermal neutrons is required. In this study, K2CeCl5/6LiCl and CeCl3/SrCl2/6LiCl were developed as novel eutectic scintillators for thermal neutron detection. LiCl was selected as the neutron capture phase and K2CeCl5 and CeCl3 were used as the scintillator phases. The eutectics of K2CeCl5/6LiCl and CeCl3/SrCl2/6LiCl were prepared using the Vertical Bridgman method and the phases were identified by scanning electron microscopy and powder X-ray diffraction measurements. The results of radioluminescence measurements under Ag source X-ray tube irradiation confirmed that the 5d-4f emission derived from Ce3+. The cathodoluminescence spectra and thermal neutron responses of the prepared eutectics were measured to evaluate their optical properties.

To date, 3He gas has been commonly used to detect thermal neutrons because of their high chemical stability and low sensitivity to γ-rays, owing to their low density and large neutron capture cross-section. However, the depletion of 3He gas prompts the development of a new solid scintillator for thermal neutron detection to replace 3He gas detectors. Solid scintillators containing 6Li are commonly used to detect thermal neutrons. However, they are currently used in single crystals only, and their 6Li concentration is defined by their chemical composition. In this study, 6Li-containing eutectic scintillators were developed. CeCl3 was selected as the scintillator phase because of its low density (3.9 g/cm3); high light yield (30,000 photons/MeV); and fast decay time with four components of 4.4 ns (6.6%), 23.2 ns (69.6%), 70 ns (7.5%) and >10 μs (16.3%), owing to the Ce3+ 5d-4f emission peak at approximately 360 nm. Crystals of the CeCl3, LiCl and CaCl2 ternary eutectic were fabricated by the vertical Bridgman technique. The grown eutectic crystals exhibited Ce3+ 5d-4f emission with a peak at 360 nm. The light yield was 18,000 photons/neutron, and the decay time was 10.5 ns (27.7%) and 40.1 ns (72.3%). Therefore, this work demonstrates optimization by combining a scintillator phase and Li-rich matrix phase for high Li content, fast timing, high light yield and low density.

The technology to grow single crystals of the required shape directly from a melt has been researched extensively and developed in various industries and research fields. In this study, a micro-pulling-down method and a Mo crucible were applied to the shape-controlled crystal growth of Y3Al5O12:Ce (YAG:Ce). Three types of Mo crucibles with different die shapes were developed. Stable crystal growth of more than 50 mm in length was achieved with the same shape as the die, and scintillation light output of ~20,000 ph/MeV, which is comparable with those of the YAG:Ce crystal grown by Cz method, were obtained. The transmittance of grown crystals above 500 nm was above 70%. The standard deviation (σ) of the scintillation light output at each position of the 50-mm-long sample was found to be within ±16%.

This manuscript summarizes recent results on the development of composite luminescent materials based on the single-crystalline films and single crystals of simple and mixed garnet compounds obtained by the liquid-phase epitaxy growth method. Such composite materials can be applied as scintillating and thermoluminescent (TL) detectors for radiation monitoring of mixed ionization fluxes, as well as scintillation screens in the microimaging techniques. The film and crystal parts of composite detectors were fabricated from efficient scintillation/TL materials based on Ce3+-, Pr3+-, and Sc3+-doped Lu3Al5O12 garnets, as well as Ce3+-doped Gd3−xAxAl5−yGayO12 mixed garnets, where A = Lu or Tb; x = 0–1; y = 2–3 with significantly different scintillation decay or positions of the main peaks in their TL glow curves. This work also summarizes the results of optical study of films, crystals, and epitaxial structures of these garnet compounds using absorption, cathodoluminescence, and photoluminescence. The scintillation and TL properties of the developed materials under α- and β-particles and γ-quanta excitations were studied as well. The most efficient variants of the composite scintillation and TL detectors for monitoring of composition of mixed beams of ionizing radiation were selected based on the results of this complex study.

A novel single-crystal growth method was developed, using arc plasma and metal melt, for a quick survey of high melting point materials. Single crystals of Yb-doped Lu2O3, Lu0.388Hf0.612O1.806, and Lu0.18Hf0.82O1.91, with melting points of 2460, 2900, and 2840 °C, respectively, were grown by an indirect heating method using arc plasma. We refer to this indirect heating growth method as the core heating (CH) method. The CH-grown Yb1%-doped Lu2O3 sample showed a full width at half maximum of 286 arcsec in the X-ray rocking curve. This value is better than the 393 arcsec obtained for the crystal grown by the micro-pulling-down (μ-PD) method. The Yb charge transfer state (CTS) emission was observed at 350 nm in the Yb1%-doped Lu2O3 and Lu0.18Hf0.82O1.91. In the case of the μ-PD method, using a rhenium (Re) crucible, absorption due to Re contamination and a resulting reduction in the Yb CTS emission were confirmed. However, contamination did not influence the properties observed in the crystals grown by the CH method.

Ce-doped LaBr3/AEBr2 (AE = Mg, Ca, Sr, Ba) eutectics were grown using the Bridgman–Stockbarger (BS) method in quartz ampoules. The eutectics (AE = Mg and Ca) showed optical transparency like optical fiber bundles. A grown Ce-doped LaBr3/MgBr2 eutectic shows a 355 nm emission ascribed to Ce3+ 4f-5d transition under X-ray excitation. The smaller the ionic size of AE, the higher the light yield of the sample was. The light yield of Ce:LaBr3/MgBr2 was 34,300 photon/MeV, which is higher than Ce:LYSO standard. Scintillation decay time under 662 keV gamma-ray excitation was 18.8 ns.

The microstructure and mechanical properties of platinum (Pt) fibers fabricated by unidirectional solidification using the alloy-micro-pulling-down (A-μ-PD) method were investigated using a Universal Testing Machine and Electron Backscattered Diffraction (EBSD). The Pt fiber fabricated at a growth rate of 10 mm/min was composed of relatively large grains with crystal orientation along the growth direction. The crystal orientation was consistent with the easy axis of the crystal growth on the face-centered-cubic (f.c.c.) structure. On the other hand, the adjacent grains of the Pt fiber fabricated at 50 mm/min were randomly oriented owing to a faster growth rate. In tensile tests, the Pt fibers fabricated by the A-μ-PD method indicated extremely different stress−strain curves compared to the commercial Pt wire. The maximum tensile stress of the Pt fiber reached ~100 MPa, and the Pt fiber ruptured after 58% nominal strain.

Co-Cr-Mo alloy fibers of 2 mm in diameter were fabricated from the melt at 1, 2, and 5 mm/min growth rates by unidirectional solidification using an alloy-micro-pulling-down (A-µ-PD) method to control the microstructure. All elements, Co, Cr, and Mo, were distributed in stripes elongated along the growth direction due to constitutional undercooling. Both Co-Cr-Mo fibers fabricated at 2 and 5 mm/min growth rates were composed of the γ phase with a face-centered cubic structure (fcc-γ phase) and ε-phase with a hexagonal close-packed structure (hcp-ε phase), and the ratio of the fcc-γ phase in the fiber fabricated at 5 mm/min growth rate was higher than that in the fiber fabricated at 2 mm/min. The results suggest that a faster growth rate increases the ratio of the fcc-γ phase in the Co-Cr-Mo fiber fabricated by unidirectional solidification.

Ca3Nb(Ga1−xAlx)3Si2O14 (CNGAS) single crystals with various Al concentrations were grown by a micro-pulling-down (µ-PD) method and their crystal structures, chemical compositions, crystallinities were investigated. CNGAS crystals with x = 0.2, 0.4 and 0.6 indicated a single phase of langasite-type structure without any secondary phases. In contrast, the crystals with x = 0.8 and 1 included some secondary phases in addition to the langasite-type phase. Lattice parameters, a- and c-axes lengths, of the langasite-type phase systematically decreased with an increase of Al concentration. The results of chemical composition analysis revealed that the actual Al concentrations in as-grown crystals were almost consistent with the nominal compositions. In addition, there was no large segregation of each cation along the growth direction.

Previously, studying the development, especially of corticospinal neurons, it was concluded that the main compensatory mechanism after unilateral brain injury in rat at the neonatal stage was due in part to non-lesioned ipsilateral corticospinal neurons that escaped selection by axonal elimination or neuronal apoptosis. However, previous results suggesting compensatory mechanism in neonate brain were not correlated with high functional recovery. Therefore, what is the difference among neonate and adult in the context of functional recovery and potential mechanism(s) therein? Here, we utilized a brain unilateral decortication mouse model and compared motor functional recovery mechanism post-neonatal brain hemisuction (NBH) with adult brain hemisuction (ABH). Three analyses were performed: (1) Quantitative behavioral analysis of forelimb movements using ladder walking test; (2) neuroanatomical retrograde tracing analysis of unlesioned side corticospinal neurons; and (3) differential global gene expressions profiling in unlesioned-side neocortex (rostral from bregma) in NBH and ABH on a 8 × 60 K mouse whole genome Agilent DNA chip. Behavioral data confirmed higher recovery ability in NBH over ABH is related to non-lesional frontal neocortex including rostral caudal forelimb area. A first inventory of differentially expressed genes genome-wide in the NBH and ABH mouse model is provided as a resource for the scientific community.