Search

This study presents an investigation of the effects of structural characteristics, such as the layer height, infill density, top/bottom layer line directions and infill pattern, on the structural efficiency of Acrylonitrile Butadiene Styrene (ABS)-based specimens. The Fused Filament Fabrication (FFF) technique was utilized for the specimen fabrication, and the Ultimate Tensile Strength (UTS) and Strength-to-Mass (S/M) ratio were examined. The tests were planned according to the Central Composite Design (CCD), and an empirical model for each response was developed, with respect to the applied factors and their interactions. The analysis revealed that the characteristics with the strongest influence on the UTS and the S/M ratio were the infill and the layer height, respectively. Moreover, it was observed that the honeycomb structure contributed to the highest UTS compared to the other patterns. Finally, an optimization analysis based on the desirability function was performed, highlighting the combination of a 0.3 mm layer, 21.81% and 76.36% infill, 0° direction and the honeycomb pattern as the optimal for maximizing both UTS and S/M ratio under different desirability.

Ultrasonic welding (USW) of thermoplastics plays a significant role in the automobile industry. In this study, the effect of the welding time on the joint strength of ultrasonically welded acrylonitrile–butadiene–styrene (ABS) and the weld formation mechanism were investigated. The results showed that the peak load firstly increased to a maximum value of 3.4 kN and then dropped with further extension of the welding time, whereas the weld area increased continuously until reaching a plateau. The optimal welding variables for the USW of ABS were a welding time of 1.3 s with a welding pressure of 0.13 MPa. Interfacial failure and workpiece breakage were the main failure modes of the joints. The application of real-time horn displacement into a finite element model could improve the simulation accuracy of weld formation. The simulated results were close to the experimental results, and the welding process of the USW of ABS made with a 1.7 s welding time can be divided into five phases based on the amplitude and horn displacement change: weld initiation (Phase I), horn retraction (Phase II), melt-and-flow equilibrium (Phase III), horn indentation and squeeze out (Phase IV) and weld solidification (Phase V). Obvious pores emerged during Phase IV, owing to the thermal decomposition of the ABS. This study yielded a fundamental understanding of the USW of ABS and provides a theoretical basis and technological support for further application and promotion of other ultrasonically welded thermoplastic composites.

This study is focused on the application of 3D-printed elements and conventional elements to create a prototype of a custom-made exoskeleton for lower limb rehabilitation. The 3D-printed elements were produced by using Fused Deposition Modeling technology and acrylonitrile butadiene styrene (ABS) material. The scope of this work involved the design and construction of an exoskeleton, experimental testing of the ABS material and numerical research by using the finite element method. On the basis of the obtained results, it was possible to deduce whether the load-bearing 3D-printed elements can be used in the proposed mechanical construction. The work contains full data of the material models used in FEM modeling, taking into account the orthotropic properties of the ABS material. Various types of finite elements were used in the presented FE models. The work is a comprehensive combination of material testing issues with the possibility of implementing the obtained results in numerical strength models of machine parts.

This paper investigates the effects of sodium laureth sulfate (SLES) on the wettability of the surface of the two most common recycled plastics in refrigeration equipment: HIPS (high-impact polystyrene) and ABS (acrylonitrile–butadiene–styrene). These plastics, in the form of flakes, were identified on the basis of their FTIR spectra, and then, they were subjected to a study of contact angles using the sessile droplet method. The solutions for the angle analysis included tap water with the addition of SLES. The results of this study showed that at SLES concentrations of 0.1 g/L and 0.2 g/L, the differences in the contact angles for HIPS and ABS were 10.76° and 10.10°, respectively. This research confirmed the potential of using SLES as a support for the flotation separation of plastics with similar densities and surface characteristics, such as HIPS and ABS.

In this work, a self-lubricating composite was manufactured using a novel hybrid 3D printing/in situ spraying process that involved the printing of an acrylonitrile butadiene styrene (ABS) matrix using fused deposition modeling (FDM), along with the in situ spraying of alumina (Al2O3) and hexagonal boron nitride (hBN) reinforcements during 3D printing. The results revealed that the addition of the reinforcement induced an extensive formation of micropores throughout the ABS structure. Under tensile-loading conditions, the mechanical strength and cohesive interlayer bonding of the composites were diminished due to the presence of these micropores. However, under tribological conditions, the presence of the Al2O3 and hBN reinforcement improved the frictional resistance of ABS in extreme loading conditions. This improvement in frictional resistance was attributed to the ability of the Al2O3 reinforcement to support the external tribo-load and the shearing-like ability of hBN reinforcement during sliding. Collectively, this work provides novel insights into the possibility of designing tribologically robust ABS components through the addition of in situ-sprayed ceramic and solid-lubricant reinforcements.

This paper presents the results of research on the influence of the moisture content in a filament made of ABS polymer on the properties of products manufactured using FDM (fused deposition modeling). Tests were carried out on a standard printer, using the parameters recommended by the manufacturer and the literature on the subject. A special climatic chamber was used to condition the material. A negative impact of ABS filament moisture on the strength and dimensional accuracy of printed products and on the structure of their surface is demonstrated. When the range of the filament moisture is between 0.17% and 0.75%, the strength decreases by 25% and the sample thickness increases by 10%. It is also shown that this effect does not depend on the history of the polymer reaching a given moisture level, i.e., by absorbing moisture in the absorption process or releasing moisture in the desorption process.

Temperature is very important in the fabrication of products developed for different applications, considering the widespread use of additive manufacturing (AM) technology. Thermal properties seriously affect the mechanical properties of products. In this study, the effect of printing nozzle temperature changes on the dimensional and mechanical properties of samples fabricated with acrylonitrile butadiene styrene (ABS) material was investigated. This material can be preferred over foam material for drone and model aircraft areas due to its low density. A total of thirty-six tensile test samples (ISO527–type1A) were fabricated with fused filament fabrication (FFF), one of the AM methods, and their dimensional properties (length, width, thickness, and mass) were determined. During the fabrication process, the nozzle temperature of the 3D (three-dimensional) printer was increased from 220 °C to 270 °C in 10 °C increments. All samples were subjected to tensile testing, and stress–strain values were measured. Analysis of variance (ANOVA) was applied to examine the effect of nozzle temperature change on the findings obtained as a result of the experimental study. The printing nozzle temperature significantly affected both the mechanical strength and dimensional properties of the samples. The samples showed lower viscosity and less hardness at higher nozzle temperatures. The mass and density of the samples decreased with increasing temperature. The tensile strength value decreased by 41.52%.

This paper presents the results of experimental investigation of the mechanical characteristics of 3D-printed acrylonitrile butadiene styrene (ABS) and its modifications reinforced with different types of short-fiber fillers: carbon, glass, and basalt. Elastic modulus, tensile and bending strength, as well as fracture toughness were determined in series of mechanical tests for samples produced with different manufacturing parameters, such as nozzle diameter and infill angle. It was found that the use of ABS filament reinforced with the short fibers can significantly improve the mechanical properties of 3D-printed devices when the infill angle is oriented along the vector of the applied load. In such a case, the elastic modulus and tensile strength can be increased by more than 1.7 and 1.5 times, respectively. The use of a larger nozzle diameter led to the growth of tensile strength by an average of 12.5%. When the macroscopic load is applied along the normal to the printed layers, the addition of short fibers does not give much gain in mechanical properties compared to pure ABS, which was confirmed by both standard tensile and fracture toughness tests. The surface of the fractured samples was examined using scanning electronic microscopy, which allowed us to make conclusions on the type of defects as well as on the level of adhesion between the polymeric matrix and different types of short fibers.

The present work proposes to investigate the effect of an ultrahigh molecular weight silicone rubber (UHMW-SR) and two ethylene methyl acrylate copolymers (EMA) with different methyl acrylate (MA) content on the mechanical and fire performance of a fireproof acrylonitrile butadiene styrene copolymer (ABS) composite, with an optimum amount of ammonium polyphosphate (APP) and aluminum diethyl phosphinate (AlPi). ABS formulations with a global flame retardant weight content of 20 wt.% (ABS P) were melt-compounded, with and without EMA and UHMW-SR, in a Brabender mixer. During this batch process, ABS P formulations with UHMW-SR and/or EMA registered lower torque values than those of ABS P. By means of scanning electron microscopy (SEM), it was possible to observe that all ABS composites exhibited a homogenous structure without phase separation or particle agglomeration. Slightly improved interfacial interaction between the well-dispersed flame-retardant particles in the presence of EMA and/or UHMW-SR was also noticed. Furthermore, synergies in mechanical properties by adding both EMA and UHMW-SR into ABS P were ascertained. An enhancement of molecular mobility that contributed to the softening of ABS P was observed under dynamic mechanical thermal analysis (DMTA). An improvement of its flexibility, ductility and toughness were also registered under three-point-bending trials, and even more remarkable synergies were noticed in Charpy notched impact strength. Particularly, a 212% increase was achieved when 5 wt.% of EMA with 29 wt.% of MA and 2 wt.% of UHMW-SR in ABS P (ABS E29 S P) were added. Thermogravimetric analysis (TGA) showed that the presence of EMA copolymers in ABS P formulations did not interfere with its thermal decomposition, whereas UHMW-SR presence decreased its thermal stability at the beginning of the decomposition. Although the addition of EMA or UHMW-SR, as well as the combination of both in ABS P increased the pHRR in cone calorimetry, UL 94 V-0 classification was maintained for all flame-retarded ABS composites. In addition, through SEM analysis of cone calorimetry sample residue, a more cohesive surface char layer, with Si-O-C network formation confirmed by Fourier transform infrared (FTIR), was shown in ABS P formulations with UHMW-SR.

In view of the increasing amount of plastic waste due to a yearly rise in production volume, mechanical recycling of post-industrial waste offers a way to use the scarce resources on earth more efficiently in addition to reducing the global warming potential in the production of raw materials. Therefore, this study addresses the calculation of the product carbon footprint for sorted industrial waste according to the specifications of ISO 14067. The plastics acrylonitrile–butadiene–styrene copolymer (ABS), polyamide 6.6 with 30% glass fiber (PA66GF30), polycarbonate (PC) and polyoxymethylene (POM) were balanced in Umberto LCA+ using the Ecoinvent v3.8 and GaBi SP40 2020 databases and primary data collection from the recycling company Occhipinti. A cut-off approach was applied as an allocation method for evaluating the industrial waste so that the plastic for grinding was imported without burdens from the previous product system. The results show that for all plastics under study, one of the main drivers of the carbon footprint is plastic dust from the grinding process. This insight was used in sensitivity analyses to optimize the modelled processes for a more sustainable production. Improvement potentials were identified by using solar power and disposing of the plastic dust separately according to the type of plastic.

In this study, organosilicon compounds were used as modifiers of filaments constituting building materials for 3D printing technology. Polymethylhydrosiloxane underwent a hydrosilylation reaction with styrene, octadecene, and vinyltrimethoxysilane to produce new di- or tri-functional derivatives with varying ratios of olefins. These compounds were then mixed with silica and incorporated into the ABS matrix using standard processing methods. The resulting systems exhibited changes in their physicochemical and mechanical characteristics. Several of the obtained composites (e.g., modified with VT:6STYR) had an increase in the contact angle of over 20° resulting in a hydrophobic surface. The addition of modifiers also prevented a decrease in rheological parameters regardless of the amount of filler added. In addition, comprehensive tests of the thermal decomposition of the obtained composites were performed and an attempt was made to precisely characterize the decomposition of ABS using FT-IR and optical microscopy, which allowed us to determine the impact of individual groups on the thermal stability of the system.

This study surveys the impacts of injection parameters on the deformation rate of the injected flexure hinge made from ABS, PP, and HDPE. The flexure hinges are generated with different filling time, filling pressure, filling speed, packing time, packing pressure, cooling time, and melt temperature. The amplification ratio of the samples between different injection parameters and different plastic types is measured and compared to figure out the optimal one with a high amplification ratio. The results show that the relationship between the input and output data of the ABS, PP, and HDPE flexure hinges at different injection molding parameters is a linear relation. Changing the material or many injection molding parameters of the hinge could lead to a great impact on the hinge’s performance. However, changing each parameter does not lead to a sudden change in the input and output values. Each plastic material has different optimal injection parameters and displacement behaviors. With the ABS flexure hinge, the filling pressure case has the greatest amplification ratio of 8.81, while the filling speed case has the lowest value of 4.81. With the optimal injection parameter and the input value of 105 µm, the ABS flexure hinge could create a maximum average output value of 736.6 µm. With the PP flexure hinge, the melt temperature case achieves the greatest amplification ratio of 6.73, while the filling speed case has the lowest value of 4.1. With the optimal injection parameter and the input value of 128 µm, the PP flexure hinge could create a maximum average output value of 964.8 µm. The average amplification ratio values of all injection molding parameters are 6.85, 5.41, and 4.01, corresponding to ABS, PP, and HDPE flexure hinges. Generally, the ABS flexure hinge has the highest amplification ratios, followed by the PP flexure hinge. The HDPE flexure hinge has the lowest amplification ratios among these plastic types. With the optimal injection parameter and the input value of 218 µm, the HDPE flexure hinge could create a maximum average output value of 699.8 µm. The results provide more insight into plastic flexure hinges and broaden their applications by finding the optimal injection parameters and plastic types.

Three-dimensional (3D) printer usage in household and school settings has raised health concerns regarding chemical and particle emission exposures during operation. Although the composition of 3D printer emissions varies depending on printer settings and materials, little is known about the impact that emissions from different filament types may have on respiratory health and underlying cellular mechanisms. In this study, we used an in vitro exposure chamber system to deliver emissions from two popular 3D-printing filament types, acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA), directly to human small airway epithelial cells (SAEC) cultured in an air–liquid interface during 3D printer operation. Using a scanning mobility particle sizer (SMPS) and an optical particle sizer (OPS), we monitored 3D printer particulate matter (PM) emissions in terms of their particle size distribution, concentrations, and calculated deposited doses. Elemental composition of ABS and PLA emissions was assessed using scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM-EDX). Finally, we compared the effects of emission exposure on cell viability, inflammation, and metabolism in SAEC. Our results reveal that, although ABS filaments emitted a higher total concentration of particles and PLA filaments emitted a higher concentration of smaller particles, SAEC were exposed to similar deposited doses of particles for each filament type. Conversely, ABS and PLA emissions had distinct elemental compositions, which were likely responsible for differential effects on SAEC viability, oxidative stress, release of inflammatory mediators, and changes in cellular metabolism. Specifically, while ABS- and PLA-emitted particles both reduced cellular viability and total glutathione levels in SAEC, ABS emissions had a significantly greater effect on glutathione relative to PLA emissions. Additionally, pro-inflammatory cytokines including IL-1β, MMP-9, and RANTES were significantly increased due to ABS emissions exposure. While IL-6 and IL-8 were stimulated in both exposure scenarios, VEGF was exclusively increased due to PLA emissions exposures. Notably, ABS emissions induced metabolic perturbation on amino acids and energy metabolism, as well as redox-regulated pathways including arginine, methionine, cysteine, and vitamin B3 metabolism, whereas PLA emissions exposures caused fatty acid and carnitine dysregulation. Taken together, these results advance our mechanistic understanding of 3D-printer-emissions-induced respiratory toxicity and highlight the role that filament emission properties may play in mediating different respiratory outcomes.

Polylactic Acid (PLA) and Acrylonitrile–Butadiene–Styrene (ABS) are commonly used polymers in 3D printing for biomedical applications. Dental Pulp Stem Cells (DPSCs) are an accessible and proliferative source of stem cells with significant differentiation potential. Limited knowledge exists regarding the biocompatibility and genetic safety of ABS and PLA when in contact with DPSCs. This study aimed to investigate the impact of PLA and ABS on the adhesion, proliferation, osteogenic differentiation, genetic stability, proteomics, and immunophenotypic profile of DPSCs. A total of three groups, 1- DPSC-control, 2- DPSC+ABS, and 3- DPSC+PLA, were used in in vitro experiments to evaluate cell morphology, proliferation, differentiation capabilities, genetic stability, proteomics (secretome), and immunophenotypic profiles regarding the interaction between DPSCs and polymers. Both ABS and PLA supported the adhesion and proliferation of DPSCs without exhibiting significant cytotoxic effects and maintaining the capacity for osteogenic differentiation. Genetic stability, proteomics, and immunophenotypic profiles were unaltered in DPSCs post-contact with these polymers, highlighting their biosafety. Our findings suggest that ABS and PLA are biocompatible with DPSCs and demonstrate potential in dental or orthopedic applications; the choice of the polymer will depend on the properties required in treatment. These promising results stimulate further studies to explore the potential therapeutic applications in vivo using prototyped polymers in personalized medicine.

This research focuses on the fabrication of plastic flexure hinges from diverse plastics such as ABS, PP, HDPE, and LDPE. To enhance hinge efficiency, the recycling ratios are also investigated. The amplification ratio of different recycle ratios and plastic types are measured. The results show that the input and output displacements of all PP, ABS, and HDPE hinges are linear. The presence of recycled plastics has no impact on this basis. The pure PP, ABS, and HDPE flexure hinges achieve the highest amplification ratios of 5.728, 8.249, and 5.668. The addition of recycled plastics reduces the amplification ratio. This decrease in the amplification ratio, however, is small. At a 25% recycle ratio, the PP, ABS, and HDPE flexure hinges have 12%, 13.3%, and 21.7% lower amplification ratios than the pure plastic hinges. Furthermore, the utilization of recycled plastics may lessen the need for new plastic made from raw materials. With the PP flexure hinge, a maximum input value of 157 µm could result in an output value of 886 µm. At a maximum input value of 115 µm, the ABS flexure hinge could achieve an output value of 833 µm. Finally, a maximum input value of 175 µm might result in an output value of 857 µm when using the HDPE flexure hinge. The average amplification ratio values for all recycling ratios for PP, ABS, and HDPE flexure hinges are, respectively, 5.35, 7.60, and 5.02. The ABS flexure hinge frequently outperforms the PP and HDPE flexure hinge in terms of amplification ratios. Among these plastics, HDPE flexure hinges have the lowest amplification ratio. In general, increasing the thermoplastic polyurethane (TPU) content of the LDPE/TPU blend increases the amplification ratio. The cause could be the TPU’s high compatibility with the LDPE polymer. The LDPE/TPU blend hinge offers a broader range of the amplification ratio of 2.85–10.504 than the PP, ABS, and HDPE flexure hinges. It is interesting that changing the blend percentage has a much greater impact on the amplification ratio than changing the recycling ratio. The findings broaden the range of applications for plastic flexure hinges by identifying optimal plastic types. The impact of the hinge shape on the performance of the injected plastic flexure hinge might be studied in further research.

In fused deposition modeling (FDM), the cooling history impacts the bonding between filaments and layers. The existence of thermal gradients can cause non-homogeneous properties and localized stress points that may affect the individual filaments, resulting in distortion and detachment. Thermal analysis can aid in understanding the manufacturing flaw, providing necessary tools for the optimization of the printing trajectory. The present work is intended to deepen understanding of the thermal phenomena occurring during the extrusion of polymeric materials, aiming at more efficient three-dimensional (3D) printing methods. A one-dimensional (1D) finite differential method was implemented using MATLAB to simulate the temperature evolution of an extruded filament, and the results were compared with two-dimensional (2D) COMSOL Multiphysics simulations, and experimentally validated using infrared thermography. Acrylonitrile–butadiene–styrene (ABS) was used as a test material. The energy dissipation includes forced convection and radiation heat losses to the surrounding medium.

In recent years, additive manufacturing technology, particularly in plastic component fabrication, has gained prominence. However, fundamental modelling of the influence of materials like ABS, PC, and PLA on tribological properties in fused deposition modeling (FDM) remains scarce, particularly in non-lubricated, oil-lubricated, and grease-lubricated modes. This experimental study systematically investigates the effects of material type, lubrication method, layer thickness, and infill density on FDM component tribology. A tribology analysis is conducted using a TRB3 tribometer. The results indicate a coefficient of friction (CoF) range between 0.04 and 0.2, generally increasing and decreasing with layer thickness and filler density. The lubrication impact hinges on the material surface texture. The study models the intricate relationships between these variables via full-factor analysis, showing a strong alignment between the modelled and measured friction coefficients (an average error of 3.83%). Validation tests on different materials affirm the model’s reliability and applicability.

Four-dimensional printing is a process in which a 3D-printed object is intentionally transformed in response to an external stimulus such as temperature, which is useful when the final geometry of a 3D-printed part is not easily manufacturable. One method to demonstrate this is to print a part made of thin strips of material on a sheet of paper, heat the part, and allow it to cool. This causes the part to curl due to the difference in the thermal expansion coefficients of the paper and plastic. In an attempt to quantify the effect of different temperatures on various materials, samples of three common 3D printing filaments, acrylonitrile butadiene styrene (ABS), polyethylene terephthalate glycol (PETG), and polylactic acid (PLA), were heated at different temperatures (85 °C, 105 °C, and 125 °C) for intervals of 15 min and then allowed to cool until curling stopped. This heating and cooling cycle was repeated three times for each sample to determine if repeated heating and cooling influenced the curling. Each sample was filmed as it was cooling, which allowed the radius of curvature to be measured by tracking the uppermost point of the part, knowing the arc length, and calibrating the video based on a known linear length. After three cycles, all three materials showed a decrease in the radius of curvature (tighter curl) as heating temperature increased, with PLA showing the trend much more predominantly than ABS and PETG. Furthermore, for PETG and PLA, the radius of curvature decreased with each cycle at all temperatures, with the decrease being more significant from cycle 1 to 2 than cycle 2 to 3. Conversely, ABS only shared this trend at 125 °C. The findings of this work can provide guidelines to users on the temperature dosage for the mass manufacturing of complex geometries such as packaging, self-assembly robots, and drug delivery applications.

The multicomponent injection molding of liquid silicone rubbers (LSR) with thermoplastics, such as polybutylene terephthalate (PBT) or polyamide (PA), is a state-of-the-art technique and is used in the manufacturing process for many components in the automotive industry and in the field of sanitary engineering. Standard thermoplastics, such as acrylonitrile butadiene styrene (ABS), cannot be bonded with silicone rubbers in injection molding because of their low heat deflection temperature. In this study, we investigated ABS grades approved for medical applications to show how dynamic mold heating and various pretreatment methods for thermoplastic surfaces can be used to produce ABS-LSR test specimens. In addition, such components’ sterilization effect on the adhesive bond will be shown.

The purpose of this work was to investigate the structural, thermal, micromechanical and tribological properties of novel polymer/metal composite materials for bearing applications. Copper (Cu)-filled Acrylonitrile Butadiene Styrene (ABS) composites were mixed in a laboratory scale by an internal mixer with two blade impellers, and then injection-molded. Neat ABS, ABS+5wt% Cu, ABS+10wt% Cu, and ABS+15wt% Cu were the four materials that were tested. The dispersion of Cu particles in the ABS matrix was investigated using Scanning Electron Microscopy (SEM) and a micro-tomography scan. The filler particles have a uniform distribution in the matrix, according to the observations. The incorporation of Cu filler also refined an increase in the glass transition temperature from Differential Scanning Calorimetry (DSC) and less intensity in the amorphous phase by X-ray diffraction (XRD). Nanoindentation tests were carried out to characterize the micro-mechanical behavior of the composites. Friction and wear analysis were also examined using a pin-on-disk tribometer. Compared with neat ABS, all the micro-composites showed much higher indentation hardness, Vickers hardness, and indentation elastic modulus. It was also concluded that the incorporation of Cu filler into ABS simultaneously improved the friction and wear properties of the composites, which contributed to the suitability of the micro-filled composites with hard metallic particles for a wider range of mechanical components for bearing applications.

This article studies the flexural behavior of thin-walled specimens with square hollow sections fabricated using fused deposition modeling (FDM). The specimens were 3D printed from an ABS filament reinforced with aramid fibers. Four wall thicknesses were analyzed. The strength data were collected during three-point flexural tests. There are visible, clear differences in the flexural properties between the X- or Y-oriented specimens and those printed in the Z direction, and they vary up to 70%. It was also found that the flexural strength was dependent on the G-codes controlling the print head’s motion, path, and position. For specimens with a thickness up to 1.4 mm, the infill pattern was linear, whereas 1.8 mm and 2 mm specimens needed a stitch, which had some negative effects on the strength properties.

This article introduces a multi-objective optimization approach for determining the best 3D printing parameters (layer thickness and infill percentage) to efficiently produce PLA and ABS parts, extensively analyzing mechanical behavior under tests for different traits such as tensile strength, compression, flexural, impact, and hardness. The value analysis method is used to optimize settings that balance use value (Vi- represented by mechanical characteristics) and production cost (Cp). Findings reveal that the infill percentage significantly influences the Vi/Cp ratio for tensile, compression, and hardness tests, while flexural tests are influenced by layer thickness. Impact strength is influenced nearly equally by both factors, with material-specific variations. The desirability function proved useful for optimizing processes with multiple responses, identifying the optimal parameters for the FDM process: a layer thickness of 0.15 mm with 100% infill percentage for PLA, a layer thickness of 0.20 mm with 100% infill percentage for annealed PLA, and a layer thickness of 0.15 mm with 100% infill percentage for ABS. Overall, this study guides efficient 3D printing parameter selection through a technical-economic optimization based on value analysis.

New types of hybrid aluminum joints: Al-acrylonitrile butadiene styrene (ABS) carbon fiber reinforced thermoplastic polymer (CFRTP) designated Al/Ni-CFP/ABS, and Al-18-8 Stainless steel, Al/Ni-CFP/18-8, by Ni-plated carbon fiber plug (Ni-CFP) insert not before seen in the literature have been fabricated. The goal is to take advantage of extremely high ~6 mm CF surface area for high adhesion, to enhance the safety level of aircraft and other parts. This is without fasteners, chemical treatment, or glue. First, the CFP is plated with Ni. Second, the higher melting point half-length is spot welded to the CFP; and third, the remaining half-length is fabricated. The ultimate tensile strength (UTS) of Al/Ni-CFP/ABS was raised 15 times over that of Al/ABS. Normalized cUTS according to CFP cross-section by Rule of Mixtures for cAl/Ni-CFP/18-8 was raised over that of cAl/Ni-CFP/18-8 from 140 to 360 MPa. Resistance energy to tensile deformation, UT, was raised 12 times from Al/ABS to Al/Ni-CFP/ABS, and 6 times from Al/CFP/18-8 to Al/Ni-CFP/18-8. Spot welding allows rapid melting followed by rapid solidification for amorphous metal structures minimizing grain boundaries. The Ni-coating lowers or counters the effects of brittle Al4C3 and FexC formation at the interface and prevents damage by impingement to CFs, allowing joints to take on more of the load.

In recent years, there has been a growing interest in the field of 3D printing technology. Among the various technologies available, fused deposition modeling (FDM) has emerged as the most popular and widely used method. However, achieving optimal results with FDM presents a significant challenge due to the selection of appropriate process parameters. Therefore, the objective of this research was to investigate the impact of process parameters on the tribological and frictional behavior of acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA) 3D-printed parts. The design of experiments (DOE) technique was used considering the input design parameters (infill percentage and layer thickness) as variables. The friction coefficient values and the wear were determined by experimental testing of the polymers on a universal tribometer employing plane friction coupling. Multi-response optimization methodology and analysis of variance (ANOVA) were used to highlight the dependency between the coefficient of friction, surface roughness parameters, and wear on the process parameters. The optimization analysis revealed that the optimal 3D printing input parameters for achieving the minimum coefficient of friction and linear wear were found to be an infill percentage of 50% and layer thickness of 0.1 mm (for ABS material), and an infill percentage of 50%, layer thickness of 0.15 mm (for PLA material). The suggested optimization methodology (which involves minimizing the coefficient of friction and cumulative linear wear) through the optimized parameter obtained provides the opportunity to select the most favorable design conditions contributing to a more sustainable approach to manufacturing by reducing overall material consumption.

Eye movement desensitization and reprocessing (EMDR) therapy is one of the therapies recommended by the World Health Organization (2013) to treat posttraumatic stress disorder (PTSD). Although efficient, repeated exposure to the traumatic memory may reduce its acceptability to patients. The therapy “eye movement and alternate stimulation for brain integration” (MOSAIC in French) was developed to improve acceptability and reduce pain by drawing on the patient’s internal resources. MOSAIC therapy focuses on the body sensations that the patient wants to experience and avoids having to relive the traumatic memories. This observational study aimed to compare the clinical efficiency of EMDR and MOSAIC therapy for PTSD and to measure the well-being generated by both therapies. Twenty-six PTSD patients (17 females and 9 males, mean age 37.01 years, SD = 13.06) received treatment by psychiatrists and/or psychologists trained with EMDR or MOSAIC therapy. Both patient groups achieved a significant decrease in PTSD symptoms as measured with the PCL-5. However, fewer sessions were required with the MOSAIC therapy than with EMDR therapy. As expected, the level of well-being experienced by the patient during the therapy, assessed using the Lickert scale, was higher with MOSAIC than with EMDR therapy from the first session. These findings provide the first evidence of the efficacy of MOSAIC therapy treatment, which now needs to be corroborated in a larger randomized clinical trial.

Acrylonitrile butadiene styrene (ABS) is a thermoplastic polymer widely used in several everyday life applications; moreover, it is also one of the most employed plastics in contemporary artworks and design objects. In this study, the chemical and thermal properties of an ABS-based polymer and its photo-degradation process were investigated through a multi-analytical approach based on thermal, mass spectrometric and spectroscopic techniques. LEGO® building blocks were selected for studying the ABS properties. First, the composition of unaged LEGO® bricks was determined in terms of polymer composition and thermal stability; then, the bricks were subjected to UV–Vis photo-oxidative-accelerated ageing for evaluation of possible degradation processes. The modifications of the chemical and thermal properties were monitored in time by a multi-technique approach aimed at improving the current knowledge of ABS photodegradation, employing pyrolysis online with gas chromatography and evolved gas analysis, coupled with mass spectrometric detection (Py-GC-MS and EGA-MS), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and corroborated by external reflection FT-IR spectroscopy. The multimodal approach provided new evidence on the two-step degradation pathway proposed for ABS, defining molecular markers for polybutadiene oxidation and styrene-acrylonitrile depolymerization. Moreover, the results highlighted the feasibility of correlating accurate compositional and thermal data acquired by bulk techniques with external reflection FT-IR spectroscopy as a non-invasive portable tool to monitor the state of conservation of plastic museum objects in-situ.

Functionally graded materials (FGM) have attracted considerable attention in the field of composite materials and rekindled interest in research on composite materials due to their unique mechanical response achieved through material design and optimization. Compared to conventional composites, FGMs offer several advantages and exceptional properties, including improved deformation resistance, improved toughness, lightness properties, and excellent recoverability. This study focused on the production of functionally graded (FG) polymer materials by the additive manufacturing (AM) method. FG structures were produced by the fused deposition modeling (FDM) method using acrylonitrile benzidine styrene (ABS) and polylactic acid (PLA) materials, and tensile tests were performed according to ASTM D638. The effects of different layer thicknesses, volume ratios, and total thicknesses on mechanical behavior were investigated. The tensile standard of materials produced by additive manufacturing introduces geometric differences. Another motivation in this study is to reveal the differences between the results according to the ASTM standard. In addition, tensile tests were carried out by producing single-layer samples at certain volume ratios to create a numerical model with the finite element method to verify the experimental data. As a result of this study, it is presented that the FG structure produced with FDM improves mechanical behavior.

This study aimed to identify the optimum printing parameters for the fused filament fabrication (FFF) of acrylonitrile butadiene styrene (ABS) and polyamide (nylon), to improve strength properties. For this purpose, the methodology of the paper involves an experimental study that used Taguchi’s method to identify the effects of the infill pattern, infill density, and printing speed on the mechanical properties of the materials. ABS and nylon plastic parts were tested in tension to failure. Based on the results of the tensile tests, it was found that ABS material produced the highest ultimate tensile strength when printed using a tri-hexagonal infill pattern, 100% infill density, and a printing speed of 65 mm/s. On the other hand, nylon material exhibited a better performance when printed using an octet geometric structure, with identical other parameters.

Material extrusion (ME) is an additive manufacturing technique capable of producing functional parts, and its use in multi-material fabrication requires further exploration and expansion. The effectiveness of material bonding is one of the main challenges in multi-material fabrication using ME due to its processing capabilities. Various procedures for improving the adherence of multi-material ME parts have been explored, such as the use of adhesives or the post-processing of parts. In this study, different processing conditions and designs were investigated with the aim of optimizing polylactic acid (PLA) and acrylonitrile–butadiene–styrene (ABS) composite parts without the need for pre- or post-processing procedures. The PLA-ABS composite parts were characterized based on their mechanical properties (bonding modulus, compression modulus, and strength), surface roughness (Ra, Rku, Rsk, and Rz), and normalized shrinkage. All process parameters were statistically significant except for the layer composition parameter in terms of Rsk. The results show that it is possible to create a composite structure with good mechanical properties and acceptable surface roughness values without the need for costly post-processing procedures. Furthermore, the normalized shrinkage and the bonding modulus were correlated, indicating the ability to utilize shrinkage in 3D printing to improve material bonding.

The effect of short carbon fiber (SCF) filler on the mechanical properties of 3D-printed acrylonitrile butadiene styrene (ABS) was investigated. The fused filament fabrication (FFF) method was used for the manufacturing of samples. Elastic properties and strength characteristics of samples made of conventional ABS and SCF-reinforced ABS were compared in tensile and bending tests. Fracture toughness and critical strain energy release rate were also determined. In addition, 3D-printed monofilament SCF-reinforced samples were fabricated, the internal structure of which was analyzed using microcomputed tomography (micro-CT). Based on the tomography data, finite-element (FE) models of representative volume elements (RVEs) of the reinforced material were created and used for the numerical calculation of effective characteristics. Numerical and experimental results for the effective elastic properties were compared with the Mori-Tanaka homogenization technique. The ABS samples filled with SCF showed considerably higher mechanical characteristics than those of the conventional ABS. Finally, the dependence between the strength characteristics and elastic properties of the samples on the diameter of the nozzle used for 3D printing was established. 3D-printed ABS reinforced with SCF demonstrated a gain in tensile strength and fracture toughness by 30% and 20%, respectively. Interlayer adhesion strength in flexure tests showed an increase of 28% compared to pure ABS samples.

Additive manufacturing or 3D printing technologies might advance the fabrication sector of personalised biomaterials with high-tech precision. The selection of optimal precursor materials is considered the first key-step for the development of new printable filaments destined for the fabrication of products with diverse orthopaedic/dental applications. The selection route of precursor materials proposed in this study targeted two categories of materials: prime materials, for the polymeric matrix (acrylonitrile butadiene styrene (ABS), polylactic acid (PLA)); and reinforcement materials (natural hydroxyapatite (HA) and graphene nanoplatelets (GNP) of different dimensions). HA was isolated from bovine bones (HA particles size < 40 μm, 125 μm) through a reproducible synthesis technology. The structural (FTIR-ATR, Raman spectroscopy), morphological (SEM), and, most importantly, in vitro (indirect and direct contact studies) features of all precursor materials were comparatively evaluated. The polymeric materials were also prepared in the form of thin plates, for an advanced cell viability assessment (direct contact studies). The overall results confirmed once again the reproducibility of the HA synthesis method. Moreover, the biological cytotoxicity assays established the safe selection of PLA as a future polymeric matrix, with GNP of grade M as a reinforcement and HA as a bioceramic. Therefore, the obtained results pinpointed these materials as optimal for future composite filament synthesis and the 3D printing of implantable structures.

The article presents the results of research on the influence of the natural moisture of a filament made of acrylonitrile–butadiene–styrene terpolymer (ABS) on the mechanical properties and quality of products fabricated with fused filament fabrication (FFF). The concept of the natural moisture of the filament was defined, and the range of its variability was identified in reference to the range of the natural ambient humidity. It is shown that a change in the ambient humidity by 10% resulted in a change in filament moisture by about 0.05%. The results of the research on the moisture variability of an ABS filament stored in a package, an airtight container, or a container with a moisture absorber are also discussed. The last part of the article presents the results of the research on the impact of the moisture of the filament in its natural range of variability on select mechanical properties of filaments and products made using FFT. It is shown that this impact was significant and had a value of 1 MPa on 0.1% filament moisture.

This work reports on tailoring the magnetic properties of acrylonitrile butadiene styrene (ABS)-based composites for their application in magnetoactive systems, such as magnetic sensors and actuators. The magnetic properties of the composites are provided by the inclusion of varying permalloy (Py—Ni75Fe20Mo5) nanoparticle content within the ABS matrix. Composites with Py nanoparticle content up to 80 wt% were prepared and their morphological, mechanical, thermal, dielectric and magnetic properties were evaluated. It was found that ABS shows the capability to include high loads of the filler without negatively influencing its thermal and mechanical properties. In fact, the thermal properties of the ABS matrix are basically unaltered with the inclusion of the Py nanoparticles, with the glass transition temperatures of pristine ABS and its composites remaining around 105 °C. The mechanical properties of the composites depend on filler content, with the Young’s modulus ranging from 1.16 GPa for the pristine ABS up to 1.98 GPa for the sample with 60 wt% filler content. Regarding the magnetic properties, the saturation magnetization of the composites increased linearly with increasing Py content up to a value of 50.9 emu/g for the samples with 80 wt% of Py content. A numerical model has been developed to support the findings about the magnetic behavior of the NP within the ABS. Overall, the slight improvement in the mechanical properties and the magnetic properties provides the ABS composites new possibilities for applications in magnetoactive systems, including magnetic sensors, actuators and magnetic field shielding.

AddJoining technique has been recently introduced to produce metal–polymer composite hybrid layered structures. The methodology combines the principles of joining and polymeric additive manufacturing. This paper presents three AddJoining process-variants investigated and demonstrated for the material combination aluminum 2024-T3 and acrylonitrile butadiene styrene to form hybrid single lap joints. The microstructure and mechanical performance were assessed. The process variant using heating control showed the ultimate lap shear force of 1.2 ± 0.05 kN and displacement at a break of 1.21 ± 0.16 mm as a result of strong bonding formation at the interface of the hybrid joints. For instance, the other two process variants tested (with epoxy adhesive, and with thin-acrylonitrile butadiene styrene (ABS) coating layer applied on the metal) presented reduced mechanical performance in comparison to process variant using heating control, namely approximately 42% and 8.3%, respectively. The former had a mixed adhesive–cohesive failure due to the lower bonding performance between the adhesive and ABS printed layers. The latter displayed a slight decrease in force in comparison to heat-control specimens. This could be explained by the presence of micro-voids formed by solvent evaporation at the ABS coating layer during AddJoining.

Cu coatings were deposited on acrylonitrile-butadiene-styrene copolymer (ABS) substrates by DC magnetron sputtering with Cu target. Cr ions generated by arc evaporation were used to bombard the ABS substrates before the Cu coating process. The influences of the Cr ion bombardment on the surface topography and chemical bonds of the ABS substrates and the adhesion of the Cu coatings on the ABS substrate were studied using scanning electron microscopy, Fourier transform infrared spectroscopy, and micro-Scratch Tester as a function of bias voltage and treatment duration. The results show that the Cr ion bombardment causes Cr particles to embed in the surface. The Cr particles can interlock with the Cu coatings and ABS substrate and significantly improve the coating adhesion. In addition, the Cr particles can act as the nucleation sites of the Cu coatings and facilitate the growth of columnar crystals. Increasing the duration of Cr ion bombardment increases the number of Cr particles and, thus, enhances the adhesion. However, the continuous bombardment results in the degeneration of the ABS surface, causing the formation of the coarse columnar structure of the Cu coatings. Increasing the bias voltage can increase the energy of the Cr particles without causing degeneration of the ABS. The Cu coating deposited on the ABS substrate treated by Cr ion with high-bias voltage and short duration shows a dense and smooth growth structure. In contrast, the bombardment of the Cr ions carried out at high-bias voltage induces the formation of an interfacial layer (amorphous carbon-rich phase) in the ABS surface, which decreases the coating adhesion. It is believed that Cu coatings with strong adhesion and dense structures could be acquired on ABS substrates by optimizing the bias voltage and duration of the Cr ion bombardment pre-treatment.

The objective of the present work is to evaluate the influence of material color on mechanical properties of fused deposition modeling (FDM) parts. The performance of the products is evaluated by testing eight different colors of acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA) material in terms of tensile strength, compressive strength, and flexural strength. The analysis of data shows a significant difference in mechanical characteristics of prints depending on filament color. For different colors, these three strengths almost follow the same rising and falling tendency. In order to explore the relationship between mechanical strengths and filament colors, the color-mixing theory and the least-squares method are adopted to fit the best ratio coefficients of different color combinations. Results are presented showing that the strength value (e.g., tensile) of the mixed color can be evaluated through that of primary colors by fitting the other strength (e.g., compressive or flexural). It is shown that the predicted value is always no more than 7% error compared with the actual strength, in spite of two-color or three-color mixtures. An additional confirmation test with seven colored PLA filaments from different suppliers was conducted to focus on the extensibility. The outcomes show the maximum fitting errors of strengths for mixed colors in all cases are within 5%, proving the effectiveness and applicability of this predicted approach. This study can bring a detailed analysis that enables better estimation of the function of material color and contributes to improving the property of FDM printed products for consumers by choosing the suitable filament color.

Fabricating complex parts using additive manufacturing is becoming more popular in diverse engineering sectors. Structural Health Monitoring (SHM) methods can be implemented to reduce inspection costs and ensure structural integrity and safety in these parts. In this study, the Surface Response to Excitation (SuRE) method was used to investigate the wave propagation characteristics and load sensing capability in conventionally and additively manufactured ABS parts. For the first set of the test specimens, one conventionally manufactured and three additively manufactured rectangular bar-shaped specimens were prepared. Moreover, four additional parts were also additively manufactured with 30% and 60% infill ratios and 1 mm and 2 mm top surface thicknesses. The external geometry of all parts was the same. Ultrasonic surface waves were generated using three different signals via a piezoelectric actuator bonded to one end of the part. At the other end of each part, a piezoelectric disk was bonded to monitor the response to excitation. It was found that hollow sections inside the 3D printed part slowed down the wave travel. The Continuous Wavelet Transform (CWT) and Short-Time Fourier Transform (STFT) were implemented for converting the recorded sensory data into time–frequency images. These image datasets were fed into a convolutional neural network for the estimation of the compressive loading when the load was applied at the center of specimens at five different levels (0 N, 50 N, 100 N, 150 N, and 200 N). The results showed that the classification accuracy was improved when the CWT scalograms were used.

The incorporation of plastic aggregates as a partial replacement of natural aggregates in cementitious materials is interesting in several ways. From a mechanical point of view, the partial substitution of sand with plastic aggregates could improve some properties (e.g., ductility, thermal insulation). This paper deals with the mechanical strength of mortars containing plastic aggregates as a partial replacement of sand. Part of the volume of sand in cement mortars is substituted with plastic aggregates which originate from WEEE (Waste from Electrical and Electronic Equipment) and consist of a mix of ABS (acrylonitrile-butadiene styrene), HIPS (high impact polystyrene) and PP (Polypropylene), or of monomaterial ABS from WEEE sorting. Three rates of replacement (by volume of sand) were tested: 10%, 15% and 30%. Mechanical tests were performed according to European standard EN196-1. The results show that compressive and flexural strength decrease with rate of replacement, but remain satisfactory for structural purposes. In addition, the density of mortar is reduced with the incorporation of plastic aggregates. The decrease of mechanical strength is mainly due to the weak bond between cement paste and plastic aggregates leading to the increase of porosity. Furthermore, it appears that mortars containing plastic aggregates could present a ductile rupture.

Plastic gears are mostly used in the textile, food, and automotive industries due to their silent operation, corrosion resistance, and light and cheap advantages. Plastic gears are generally manufactured by injection molding or hobbing methods. The excess costs of the molds used to produce parts in injection molding and the problems of wastes that occur during production in hobbing lead companies to additive manufacturing, which is an alternative application. In the additive manufacturing method, the desired amount of product is produced without the problem of waste. In this study, the wear resistance of plastic spur gears produced by the Fused Deposition Modeling (FDM) method was determined theoretically. In order to determine the service life of gears, wear tests were carried out in the Forschungsstelle fur Zahnrader und Getriebebau (FZG) type test device at the same load and rotational speeds. polylactic acid (PLA), acrylonitrile butadiene styrene (ABS), and polyethylene terephthalate (PETG) thermoplastic polymer materials were used in the production of gears. When the gears rotate at the same load and rotational speeds, the most wear was observed in ABS, PLA, and PETG at the theoretically calculated wear depths. PETG is the most resistant material in terms of wear.

Modern 3D printed components are finding applications in dynamic structures. These structures are often subject to dynamic loadings. To date, research has mostly focused on investigating the mechanical properties of these 3D printed structures with minimum attention paid to their modal analysis. This work is focused on performing experimental modal analysis of 3D printed structures. The results show that the adhesion type has the most significant impact on the vibration response and parameters obtained from the modal analysis. The average dynamic modulus, natural frequency, and damping coefficient increased by approximately 12.5%, 5.5%, and 36%, respectively, for the specimens printed using skirt adhesion compared to those printed using raft adhesion. SEM analysis suggests that the 3D printed specimens with skirt adhesion yielded flattened layers, while raft adhesion resulted in rounded layers. The flattened layers of the specimens with skirt adhesion are likely an indication of an enhanced heat transfer between the 3D printer bed and the specimen. The printed specimens with skirt adhesion are in direct contact with the printer bed during the printing process. This enhances the heat transfer between the specimen and the printer bed, causing the layers to flatten out. The enhanced heat transfer yields a better inter-layer diffusion, resulting in improved physical bonding at the layers’ interface. The improved bonding yields higher stiffnesses and natural frequencies. For the specimens with skirt adhesion, the improved heat transfer process is also likely responsible for the enhanced damping properties. The strengthened inter-layer bonding at the layer–layer interface provides better energy dissipation along the contact lines between the layers.

Fused Deposition Modeling (FDM) is capable of producing complicated geometries and a variety of thermoplastic or composite products. Thus, it is critical to carry out the relationship between the process parameters, the finished part’s quality, and the part’s mechanical performance. In this study, the optimum printing parameters of FDM using oil palm fiber reinforced thermoplastic composites were investigated. The layer thickness, orientation, infill density, and printing speed were selected as optimization parameters. The mechanical properties of printed specimens were examined using tensile and flexural tests. The experiments were designed using a Taguchi experimental design using a L9 orthogonal array with four factors, and three levels. Analysis of variance (ANOVA) was used to determine the significant parameter or factor that influences the responses, including tensile strength, Young’s modulus, and flexural strength. The fractured surface of printed parts was investigate using scanning electron microscopy (SEM). The results show the tensile strength of the printed specimens ranged from 0.95 to 35.38 MPa, the Young’s modulus from 0.11 to 1.88 GPa, and the flexural strength from 2.50 to 31.98 MPa. In addition, build orientation had the largest influence on tensile strength, Young’s modulus, and flexural strength. The optimum printing parameter for FDM using oil palm fiber composite was 0.4 mm layer thickness, flat (0 degree) of orientation, 50% infill density, and 10 mm/s printing speed. The results of SEM images demonstrate that the number of voids seems to be much bigger when the layer thickness is increased, and the flat orientation has a considerable influence on the bead structure becoming tougher. In a nutshell, these findings will be a valuable 3D printing dataset for other researchers who utilize this material.

Ironing is a useful feature for parts made by fused filament fabrication (FFF), as it can smooth out surfaces using heat and extruding a small amount of material. Like any other processing parameter for FFF, ironing also requires optimisation to ensure a smooth surface can be achieved with limited adverse effects on the other features of the printed part. Even with such a beneficial use case, ironing is still considered experimental and, therefore, this study aims to investigate its effects on dimensional accuracy, surface roughness, and the hardness of two commonly used amorphous thermoplastics, i.e., ABS (acrylonitrile butadiene styrene) and ASA (acrylonitrile styrene acrylate). An extensive comparative analysis has been provided where parts have been manufactured using a low-cost, desktop-based 3D printer, with the two materials at three different ironing line spacings (0.1 mm, 0.2 mm, 0.3 mm), three different ironing flows (10%, 20%, 30%), and three different ironing speeds (50 mm/s, 100 mm/s, 150 mm/s). The study focuses on evaluating the effects of these different ironing parameters and determining the optimal combination for bespoke product requirements. The results showed that ASA was more adversely affected by the changes in ironing parameters compared to ABS. However, the different ironing parameters were proven to improve the smoothness as well as hardness of the parts, compared to the un-ironed samples of ABS and ASA. This work provides a good comparison between two popular amorphous materials and offers ways to leverage ironing parameters to achieve dimensional accuracy, optimal surface finish, and better hardness values.

Generating polymer–metal structures by means of additive manufacturing offers huge potential for customized, sustainable and lightweight solutions. However, challenges exist, primarily with regard to reliability and reproducibility of the additively generated joints. In this study, the polymers ABS, PETG and PLA, which are common in material extrusion, were joined to grit-blasted aluminum substrates. Temperature dependence of polymer melt rheology, wetting and tensile single-lap-shear strength were examined in order to obtain appropriate thermal processing conditions. Joints with high adhesive strength in the fresh state were aged for up to 100 days in two different moderate environments. For the given conditions, PETG was most suitable for generating structural joints. Contrary to PETG, ABS–aluminum joints in the fresh state as well as PLA–aluminum joints in the aged state did not meet the demands of a structural joint. For the considered polymers and processing conditions, this study implies that the suitability of a polymer and a thermal processing condition to form a polymer–aluminum joint by material extrusion can be evaluated based on the polymer’s rheological properties. Moreover, wetting experiments improved estimation of the resulting tensile single-lap-shear strength.

This paper provides a methodology for the prediction of fracture loads in additively manufactured ABS material containing U-notches. The approach is based on the Average Strain Energy Density (ASED) criterion, which assumes that the material being analysed develops fully linear-elastic behaviour. Thus, in those cases where the material has a certain (non-negligible) amount of non-linear behaviour, the ASED criterion needs to be corrected. In this sense, in this paper, the ASED criterion is also combined with the Equivalent Material Concept (EMC) and the Fictitious Material Concept (FMC), both being corrections in which the non-linear real material is substituted by a linear equivalent or fictitious material, respectively. The resulting methodologies have been applied to additively manufactured ABS U-notched single-edge-notched bending (SENB) specimens combining five different notch radii (0, 0.25, 0.5, 1 and 2 mm) and three different raster orientations (0/90, 45/−45 and 30/−60). The results obtained demonstrate that both the ASED-EMC and the ASED-FMC combined criteria provide more accurate predictions than those obtained directly through the ASED criterion, with the ASED-EMC criterion generally providing safe more accurate predictions, with an average deviation from the experimental fracture loads between +1.0% (predicted loads higher than experimental loads) and −7.6% (predicted loads lower than experimental loads).

In this work, polyamide 6 (PA6) properties were tailored and improved using a maleic anhydride-grafted acrylonitrile-butadiene-styrene terpolymer (ABS-MA). The PA6/ABS-MA blends were prepared using a co-rotational twin-screw extruder. Subsequently, the extruded pellets were injection-molded. Blends were characterized by torque rheometry, the Molau test, Fourier transform infrared spectroscopy (FTIR), impact strength, tensile strength, Heat Deflection Temperature (HDT), Differential Scanning Calorimetry (DSC), Thermogravimetry (TG), Contact Angle, Scanning Electron Microscopy (SEM), and water absorption experiments. The most significant balance of properties, within the analyzed content range (5, 7.5, and 10 wt.%), was obtained for the PA6/ABS-MA (10%) blend, indicating that even low concentrations of ABS-MA can improve the properties of PA6. Significant increases in impact strength and elongation at break have been achieved compared with PA6. The elastic modulus, tensile strength, HDT, and thermal stability properties of the PA6/ABS-MA blends remained at high levels, indicating that maleic anhydride interacted with amine end-groups of PA6. Torque rheometry, the Molau test, and SEM analysis suggested interactions in the PA6/ABS-MA system, confirming the high properties obtained. Additionally, there was a decrease in water absorption and the diffusion coefficient of the PA6/ABS-MA blends, corroborating the contact angle analysis.

Three-dimensional printed polymeric lattice structures have recently gained interests in several engineering applications owing to their excellent properties such as low-density, energy absorption, strength-to-weight ratio, and damping performance. Three-dimensional (3D) lattice structure properties are governed by the topology of the microstructure and the base material that can be tailored to meet the application requirement. In this study, the effect of architected structural member geometry and base material on the viscoelastic response of 3D printed lattice structure has been investigated. The simple cubic lattice structures based on plate-, truss-, and shell-type structural members were used to describe the topology of the cellular solid. The proposed lattice structures were fabricated with two materials, i.e., PLA and ABS using the material extrusion (MEX) process. The quasi-static compression response of lattice structures was investigated, and mechanical properties were obtained. Then, the creep, relaxation and cyclic viscoelastic response of the lattice structure were characterized. Both material and topologies were observed to affect the mechanical properties and time-dependent behavior of lattice structure. Plate-based lattices were found to possess highest stiffness, while the highest viscoelastic behavior belongs to shell-based lattices. Among the studied lattice structures, we found that the plate-lattice is the best candidate to use as a creep-resistant LS and shell-based lattice is ideal for damping applications under quasi-static loading conditions. The proposed analysis approach is a step forward toward understanding the viscoelastic tolerance design of lattice structures.

Acrylonitrile butadiene styrene (ABS) is the most commonly used thermoplastic printing material for fused deposition modelling (FDM). FDM ABS can be used in a variety of complex working environments. Notably, the thermo-mechanical coupled loads under complex operating conditions may lead to cracking and ultimately catastrophic structural failure. Therefore, it is crucial to determine the crack depth and location before a structural fracture occurs. As these parameters affect the dynamic response of the structure, in this study, the fundamental frequency and displacement amplitude response of a cracked 3D-printed ABS cantilever beam in a thermal environment were analytically and experimentally investigated. The existing analytical model, specifically the torsional spring model used to calculate the fundamental frequency change to determine the crack depth and location was enhanced by the proposed Khan-He model. The analytical relationship between the displacement amplitude and crack was established in Khan-He model and validated for the first time for FDM ABS. The results show that a reduced crack depth and location farther from the fixed end correspond to a higher fundamental frequency and displacement amplitude. An elevated ambient temperature decreases the global elastic modulus of the cracked beam and results in a lower fundamental frequency. Moreover, a non-monotonic relationship exists between the displacement amplitude and ambient temperature. The displacement amplitude is more sensitive to the crack change than the fundamental frequency in the initial stages of crack growth.

In this paper, Acrylonitrile-Butadiene-Styrene matrix composites reinforced with Nano-silica dioxide particles were examined and prepared to study their mechanical properties. The composite sheets were pre-prepared using the hot extrusion process. Due to its wide characteristics, silica dioxide additions can strengthen the usability and mechanical features of composite thermoplastics and polymers. Furthermore, introducing silica dioxide as a filler in various attributes can help to maintain the smooth flow of sufficient powders, reduce caking, and manage viscoelasticity. Despite its advantages, 3D printing generates a significant amount of waste due to limited prints or destroyed support structures. ABS is an ideal material to use because it is a thermoplastic and amorphous polymer with outstanding thermal properties that is also applicable with the FFF (Fused Filament Fabrication) technique. The findings showed that increasing the silica dioxide content reduces the tensile strength to 22.4 MPa at 10 wt%. Toughness, ductility, and yield stress values of ABS/silica dioxide composites at 15 wt% increased, indicating that the composite material reinforced by the silica dioxide particles improved material characteristics. It is essential to consider the impact of recycling in polymer reinforcement with fillers. Furthermore, the improved mechanical qualities of the composite material encourages successful ABS recycling from 3D printing, as well as the possibility of reusing it in a similar application.

Producing parts by 3D printing based on the material extrusion process determines the formation of air gaps within layers even at full infill density, while external pores can appear between adjacent layers making prints permeable. For the 3D-printed medical devices, this open porosity leads to the infiltration of disinfectant solutions and body fluids, which might pose safety issues. In this context, this research purpose is threefold. It investigates which 3D printing parameter settings are able to block or reduce permeation, and it experimentally analyzes if the disinfectants and the medical decontamination procedure degrade the mechanical properties of 3D-printed parts. Then, it studies acetone surface treatment as a solution to avoid disinfectants infiltration. The absorption tests results indicate the necessity of applying post-processing operations for the reusable 3D-printed medical devices as no manufacturing settings can ensure enough protection against fluid intake. However, some parameter settings were proven to enhance the sealing, in this sense the layer thickness being the most important factor. The experimental outcomes also show a decrease in the mechanical performance of 3D-printed ABS (acrylonitrile butadiene styrene) instruments treated by acetone cold vapors and then medical decontaminated (disinfected, cleaned, and sterilized by hydrogen peroxide gas plasma sterilization) in comparison to the control prints. These results should be acknowledged when designing and 3D printing medical instruments.

This research focuses on thermal deformations of thermoplast during three-dimensional printing. A filament acrylonitrile butadiene styrene was used, and the main focus was put on warping. Twenty-seven cuboids divided in six categories by their length, height, surface area, color, nozzle temperature and bed temperature were printed by Fused Filament Fabrication 3D printer. The whole process was captured by a thermal camera and the movies were used to analyze the temperature distribution during printing. All printouts were measured and scanned with a 3D scanner in order to highlight any abbreviations from the original digital models. The obtained results were used to formulate some general conclusions on the influence of selected parameters on the warping process. Based on the outcomes of the study, a set of guidelines on how to minimalize warping was proposed.