Search

At the beginning of the 20th century, the eclectic artist Mariano Fortuny y Madrazo patented two innovative methods for polychrome printing on fabrics and textiles, giving life to Fortuny fabric production in Venice. The first patent was related to colour application, while the second to a special machine that allows continuous printing using cylindrical rollers. Despite the descriptions, the methodology and materials used remain a secret. In collaboration with the Fortuny Museum in Venice, this research aimed at studying and identifying the different steps of Fortuny printing methodologies. Printing matrices, fabrics and raw materials found in the artist’s studio were analysed in a multi-analytical campaign through digital microscopy, X-ray fluorescence (XRF), Fourier-transform infrared spectroscopy in attenuated total reflectance (FTIR-ATR), μ-Raman spectroscopy and gas chromatography–mass spectrometry (GC–MS). Three main pigments were identified in paper samples: ivory black, a copper-based pigment, and a carbon black pigment with ultramarine for blues. The pigments were bound with linseed oil and colophony in varying proportions. Polychrome silk fabrics were dyed with a base colour, and then the coloured patterns were superimposed by continuous printing. Prussian blue was identified as one of the textile inks. Results provided a better understanding of printing methodology.

Excessive copper (Cu2+) causes adverse effects on human health and the ecological environment. Traditional methods for detecting Cu2+ have drawbacks such as high detection costs, complex operating conditions, and being time consuming. Therefore, there is an urgent need to develop simple detection methods to better meet specific health and environment quality needs. In this work, a paper-based fluorescence sensor was prepared (herein referred to as the as-prepared method) by immersing filter paper in aqueous polyethyleneimine (PEI) solution, and its potential use in Cu2+ detection was investigated. The results showed that the as-prepared paper samples, with fluorescence properties obtained by aggregation-induced luminescence of PEI, have selective recognition of Cu2+ based on the internal filtration effect, and the lowest detection limit is 0.03 μM. In addition, the relative error of this method is in the range of 1.80~2.23%, which is relatively comparable to the national standard method (0.63~630 μM), demonstrating high accuracy. Therefore, paper-based sensors with a simple preparation method have potential applications in the detection of Cu2+ in water.

In this research work, a coated paper was prepared with poly (butylene adipate-co-terephthalate) (PBAT) film to explore its use in eco-friendly food packaging. The paper was coated with PBAT film for packaging using hot pressing, a production method currently employed in the packaging industry. The coated papers were evaluated for their structural, mechanical, thermal, and barrier properties. The structural morphology and chemical analysis of the coated paper confirmed the consistent formation of PBAT bi-layered on paper surfaces. Surface coating with PBAT film increased the water resistance of the paper samples, as demonstrated by tests of barrier characteristics, including the water vapor transmission rate (WVTR), oxygen transmission rate (OTR), and water contact angle (WCA) of water drops. The transmission rate of the clean paper was 2010.40 cc m−2 per 24 h for OTR and 110.24 g m−2 per 24 h for WVTR. If the PBAT-film was coated, the value decreased to 91.79 g m−2 per 24 h and 992.86 cc m−2 per 24 h. The hydrophobic nature of PBAT, confirmed by WCA measurements, contributed to the enhanced water resistance of PBAT-coated paper. This result presents an improved PBAT-coated paper material, eliminating the need for adhesives and allowing for the fabrication of bi-layered packaging.

The forest products industries play a vital role in the economic, social, and environmental well-being of the Lake States in the United States. While various economic contribution analyses of forest products industries have been conducted to highlight the importance of such industries to regional economies, little effort has yet been made to parse out the contribution of activities in the value chain. The value chain is a series of steps involved in producing goods or services. This study used a matrix decomposition approach to estimate the economic contribution along the value chain through multiple pathways of four forest resource-based industries using wood as inputs: biomass power generation, sawmills, paper mills, and the construction of new single-family residential structures in the Lake States. The direct and indirect economic output values in 2017 resulting from the construction of new single-family residential structures were $19.1 billion, sawmills were $2.5 billion, paper mills were $17.6 billion, and the biomass power generation industry was $759 million. Of the direct and indirect economic output contributed by each industry, the highest percentage of output attributable to the logging industry was observed from the sawmills industry (12%), followed by biomass power generation (9%), paper mills (1.4%), and the construction of new single-family residential structures (

This paper presents the limitations and potential of ATR-FTIR spectroscopy applied to the study of cellulosic textile collections. The technique helps to differentiate natural fibres according to the content of lignin, pectin, hemicellulose, and wax, although some problematic issues should be considered. The spectral differences derived from the environmental humidity uptake and the plant composition are reviewed and discussed in the light of new experimental data. Diagnostic bands are proposed that can discriminate between different fibres from different plants. The contribution of ageing is also considered, demonstrating that sometimes aged fibres cannot be reliably recognised. In contrast, the potential of ATR-FTIR spectroscopy to discriminate between natural and modified fibres is discussed and proven. The best results were obtained when microinvasive ATR-FTIR spectroscopy was coupled with SEM observations. The proposed protocol was tested on microsamples of various cellulosic materials from traditional Japanese samurai armours dating from the 16th to the 20th centuries (Morigi Collection, Museo delle Culture, Lugano, Switzerland). The results facilitated a complete characterisation of the materials and demonstrated that the protocol can be used to study a wide variety of cellulosic materials, including both natural and man-modified fibres, and paper.

Paper aging and protection processes play an essential function in the preservation of library collections and archives. In this study, some physical-mechanical properties of paper samples from XXth century books (private collections), such as pH acidity, tensile strength, and modulus of elasticity, as well as optical properties, such as absolute change in yellowness, were examined before and after treating them with hydroxyapatite nanoparticles (HAp). Accelerated light aging was also evaluated and discussed. The treatment with HAp nanoparticles increased the paper’s pH to slightly alkaline values (approximately pH 8). Washing and treating the paper improved its mechanical properties compared to untreated paper; the tear length increased by 35% and the modulus of elasticity increased by 56%. That the treated and aged samples are more elastic than the original samples demonstrates that HAp nanoparticles consolidated the cellulose fibers. Additionally, particle morphology, size, composition and size distribution were assessed via image analysis using scanning electron microscopy (SEM-EDX), atomic force microscopy (AFM), and the ImageJ processing program.

In recent years, due to environmental awareness regarding the harmfulness of polymeric materials, there has been a growing interest in using papers, especially those from alternative raw materials. The importance of using all available raw materials is imperative today. Raw materials that were once viewed as waste are now of great importance because they have the ability to replace raw materials that are used irrationally or are lacking. Cereal straw is a lignocellulosic material that could be used in the paper industry and in the production of increasingly prevalent paper packaging. The aim of this research was to analyze the relationships between the qualitative parameters of straw-based printed papers containing 30% agricultural residues (wheat, barley, or triticale). The influence of two qualitative parameters (ink penetration depth and optical ink density) on the print-through was observed using multiple regression analysis on straw-based papers produced at the laboratory level. Throughout the research, 100% recycled wood paper was used as a reference sample. The results of the regression analysis showed that none of the variables individually make a statistically significant contribution to the prediction of the dependent variable in a linear context, that is, they indicate a non-linear interaction between the variables and the specific conditions under which the dependent variable reaches local extremes and changes in the gradient. Considering the results of the regression analysis and the visualization of the relationship, the model was additionally tested with other independent variables (paper type). From the results obtained, it can be concluded that the alternative straw-based paper with 30% barley pulp has the best interaction between ink and paper, which is the most similar to the reference sample in terms of printability, while the alternative straw-based paper with 30% wheat generally differs significantly from the reference paper when all three prints are considered.

A significant increase in the consumption of recycled fiber products has been observed worldwide, and the industry is forced to solve the challenges of recycled fiber quality and add strength agents and/or virgin fibers to reach sufficient properties. In order to investigate whether the mechanical and air permeability properties of waste fiber (WF) material can be significantly improved by adding wood kraft fibers (KF), hemp soda fibers (HF), and ammonium persulfate oxidated cellulose nanofibrils (CNF), different fiber blends were prepared and tested. Results revealed the excellence of hemp fibers over wood fibers regarding the improvement of WF products. The results of WF after the addition of 10% mixed fibers (KF + HF) were higher than the results of a 50% KF addition. The impact of CNF depended on fiber composition and properties. A formula for modeling the CNF impact on different fiber compositions was proposed. Obtained fiber material samples showed suitability for home composting, thus contributing to the goals of the European Green Deal regarding reducing landfill waste and the development of cleaner products.

The aim of our contribution is to evaluate the possibilities for the biochemical utilization of paper wastes. We tested aerobic and anaerobic degradation of paper waste sludges from a plant that processes recycled paper. Testing included the assessment of phytotoxicity. We can conclude that the concentration of paper sludges did not have toxic effects on the bacterial consortium of the anaerobic or aerobic conditions. However, the leachate of paper sludges and water from sludge dewatering had a slightly negative effect on the germination of cress (Lepidium sativum L.) and lettuce (Lepidium sativum L.) seeds where the germination ranged from 83.3% to 100% but the mass yield was higher.

The pulp and paper industry plays an important role in the global economy and is inextricably linked to human life. Due to its large scale, the production process generates a large amount of wastewater, which poses a major threat to the environment. The sustainable utilization and safe treatment of pulp and paper wastewater can effectively reduce environmental pollution, improve resource utilization efficiency, protect water resources, provide economic benefits for pulp and paper enterprises, and thus promote the green and sustainable development of the pulp and paper industry. Therefore, this study discusses the pollution components of pulp and paper wastewater and their impact on the environment and human health. In this review, we aim to explore the sustainable development of pulp and paper wastewater by summarizing the characteristics of current pulp and paper wastewater, the commonly used treatment methods for pulp and paper wastewater, the application of pulp and paper wastewater recycling, and the future development direction of pulp and paper wastewater.

The coefficient of friction for different contacting materials against skin is mainly influenced by the nature of the materials (synthetic and natural fabrics), mechanical contact parameters (interfacial pressure and sliding velocities), and physiological skin conditions (ambient humidity and skin moisture content). In the present research work, seven different types of papers used in everyday life were analyzed. The physical properties of these materials were determined through tensile tests and friction tests. By comparing mechanical properties with coefficient of friction, it was possible to conclude that the coefficient of friction is strongly correlated with the mechanical properties.

Beeswax is a bio-sourced, renewable, and even edible material that stands as a convincing option to provide paper-based food packaging with moisture resistance. Nonetheless, the difficulty of dispersing it in water limits its applicability. This work uses oxidized, negatively charged cellulose nanofibers along with glycerol to stabilize beeswax-in-water emulsions above the melting point of the wax. The synergistic effects of nanocellulose and glycerol granted the stability of the dispersion even when it cooled down, but only if the concentration of nanofibers was high enough. This required concentration (0.6–0.9 wt%) depended on the degree of oxidation of the cellulose nanofibers. Rheological hindrance was essential to prevent the buoyancy of beeswax particles, while the presence of glycerol prevented excessive aggregation. The mixtures had yield stress and showed pseudoplastic behavior at a high enough shear rate, with their apparent viscosity being positively influenced by the surface charge density of the nanofibers. When applied to packaging paper, the nanocellulose-stabilized beeswax suspensions not only enhanced its barrier properties towards liquid water (reaching a contact angle of 96°) and water vapor (−2 d−1), but also to grease (Kit rating: 5) and airflow (>1400 Gurley s). While falling short of polyethylene-coated paper, this overall improvement, attained using only one layer of a biobased coating suspension, should be understood as a step towards replacing synthetic waxes and plastic laminates.

The identification of sustainable materials as an alternative to plastic is fundamental for the protection of the environment and for the safeguard of marine ecosystems. The replacement of plastic with organic materials for fish storage might affect its shelf-life due to the high concentration of oxidizable fatty acids in fish flesh. This study investigated the effectiveness of two organic packaging materials, namely coconut fiber (Coc) and paper (Pap), as alternatives to the conventionally used polystyrene (Pol), on the shelf-life, hygienic parameters, and quality traits of anchovies refrigerated for one (T0), three (T1), or seven (T2) days. The hygienic quality of anchovies packaged in the organic Pap and Coc boxes was better than the traditional Pol, probably due to the higher porosity of the packaging, which allows a higher bacterial proliferation. Results of the T-BARS test showed a lower (p < 0.05) malondialdehyde concentration in fillets from the Pap group, which increased (p < 0.05) from the first to the seventh day of storage. The polyunsaturated fatty acids concentration did not differ between groups, but it decreased (p < 0.05) from T0 to T2. Coconut fiber and paper are worthy of further investigation since these packaging materials did not affect the shelf-life and fatty acid profile of anchovies during storage.

The present study reports on the development by thermoforming of highly sustainable trays based on a bilayer structure composed of paper substrate and a film made of a blend of partially bio-based poly(butylene succinate) (PBS) and poly(butylene succinate-co-adipate) (PBSA). The incorporation of the renewable succinic acid derived biopolyester blend film slightly improved the thermal resistance and tensile strength of paper, whereas its flexural ductility and puncture resistance were notably enhanced. Furthermore, in terms of barrier properties, the incorporation of this biopolymer blend film reduced the water and aroma vapor permeances of paper by two orders of magnitude, while it endowed the paper structure with intermediate oxygen barrier properties. The resultant thermoformed bilayer trays were, thereafter, originally applied to preserve non-thermally treated Italian artisanal fresh pasta, “fusilli calabresi” type, which was stored under refrigeration conditions for 3 weeks. Shelf-life evaluation showed that the application of the PBS–PBSA film on the paper substrate delayed color changes and mold growth for 1 week, as well as reduced drying of fresh pasta, resulting in acceptable physicochemical quality parameters within 9 days of storage. Lastly, overall migration studies performed with two food simulants demonstrated that the newly developed paper/PBS–PBSA trays are safe since these successfully comply with current legislation on plastic materials and articles intended to come into contact with food.

The need for pulp and paper has risen significantly due to exponential population growth, industrialization, and urbanization. Most paper manufacturing industries use wood fibers to meet pulp and paper requirements. The shortage of fibrous wood resources and increased deforestation are linked to the excessive dependence on wood for pulp and paper production. Therefore, non-wood substitutes, including corn stalks, sugarcane bagasse, wheat, and rice straw, cotton stalks, and others, may greatly alleviate the shortage of raw materials used to make pulp and paper. Non-woody raw materials can be pulped easily using soda/soda-AQ (anthraquinone), organosolv, and bio-pulping. The use of agricultural residues can also play a pivotal role in the development of polymeric membranes separating different molecular weight cut-off molecules from a variety of feedstocks in industries. These membranes range in applications from water purification to medicinal uses. Considering that some farmers still burn agricultural residues on the fields, resulting in significant air pollution and health issues, the use of agricultural residues in paper manufacturing can eventually help these producers to get better financial outcomes from the grown crop. This paper reviews the current trends in the technological pitch of pulp and paper production from agricultural residues using different pulping methods, with an insight into the application of membranes developed from lignocellulosic materials.

(1) Background: Many drugs possess poor bioavailability, and many strategies are available to overcome this issue. In this study, smartFilm technology, i.e., a porous cellulose matrix (paper), in which the active compound can be loaded onto in an amorphous state was utilised for oral administration to improve the solubility and bioactivity of a poorly soluble BSC class IV antibiotic. (2) Methods: Norfloxacin was used as the model drug and loaded into commercially available paper. The resulting norfloxacin-loaded smartFilms were transformed into smartFilm granules via wet granulation and the resulting norfloxacin-loaded smartFilm granules were transformed into norfloxacin-loaded tablets made from paper, i.e., smartFilm tablets. The crystalline state of norfloxacin was investigated, as well as the pharmaceutical properties of the granules and the tablets. The bioactivity of the smartFilm tablets was assessed in vitro and ex vivo to determine the antibacterial activity of norfloxacin. The results were compared to a physical mixture tablet that contained non-loaded paper granules and equal amounts of norfloxacin as a crystalline powder. (3) Results: Norfloxacin-loaded smartFilm granules and norfloxacin-loaded smartFilm tablets contained norfloxacin in an amorphous state, which resulted in an improved and faster release of norfloxacin when compared to the physical mixture tablet. The bioactivity was up to three times higher when compared to the physical mixture tablet. The ex vivo model was demonstrated to be a useful tool that allows for a fast and cost-effective discrimination between “good” and “bad” formulations. It provides realistic physiological conditions and can therefore yield meaningful, additional biopharmaceutical information that cannot be assessed in classical in vitro experiments. (4) Conclusions: smartFilm tablets are a promising, universal, industrially feasible and cost-effective formulation strategy for improved solubility and enhanced bioactivity of poorly soluble drugs.

The manufacturing of paper with new functional properties is a current problem today. A method of modifying the surface layer of paper by the partial dissolution of cellulose on its surface is proposed. N-Methylmorpholine-N-oxide (NMMO) is proposed for use as a solvent, the regeneration of which provides an environmentally friendly process. It was shown that among the possible hydrate forms of the solvent, the monohydrate and higher-melting forms are optimal for modifying the paper surface. The temperature–time modes of processing were revealed and the weight gain and density increase in the course of modification were estimated. The structural and morphological features of the original and modified paper were studied by X-ray imaging and scanning microscopy. The NMMO surface treatment makes it possible to vary the air permeability of the paper, making it practically non-permeable. The capillary and pore system were radically transformed after the partial dissolution of cellulose and its coagulation, as the formed cellulose film isolates them, which leads to a decrease in surface absorbency. The processing conditions allowing for the optimization of the optical and strength properties of the modified paper samples are revealed. The resulting paper with a modified N-methylmorpholine-N-oxide surface layer can be used for printing valuable documents.

During the storage of celluloid pictures for animation films over half a century, an interleave paper adhered to acrylic paint. The purpose of this study is to establish a methodology to cleanly remove the paper from the paint. A layered film, a replica of the celluloid pictures, adhered with paper was prepared and immersed in water or ethanol. The effect of these solvents on the peeling behavior was investigated using a peel test. The maximum peel force for the dry layered film in was distributed at ~0.5 N, independently of the peel speed. The peel force was significantly reduced after the layered film was immersed in pure water or ethanol. A morphological observation revealed that the dry paper was peeled off via the cohesive failure of the paper. After the layered film was immersed in pure water, the paper was also peeled off via cohesive failure. The layered film immersed in ethanol was peeled off at the paper/paint interface. To clear the effect of the volume change in the paint on peel behavior, the relative volume was determined via image analysis. The relative volume of paint was 1.56 in pure water and 1.37 in ethanol. It can be considered that the large difference in the volume of paint induces a large shear stress at the paint/paper interface.

This work reports on the development and performance evaluation of newly developed paper sheets coated, on both sides, with thin films of biodegradable poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) for applications of food packaging. For this, PHBV/paper/PHBV multilayers were first prepared by the thermo-sealing technique, optimizing the process variables of temperature and time. Thereafter, the multilayer sheets were characterized in terms of their morphological, optical, thermal, mechanical, and barrier properties and compared with equivalent paper structures double coated with high-barrier multilayer films of petrochemical polymers. The results indicated that the double coatings of PHBV successfully improved the mechanical resistance and ductility, protected from moisture, and also reduced the aroma and oxygen permeances of paper, having a minimal effect on its optical and thermal properties. Finally, the compostability of the resultant multilayer sheets was analyzed, confirming that the presence of the PHBV coatings slightly delayed the aerobic biodegradation and disintegration of paper.

All-lignin coating formulations were prepared while combining water-soluble cationic kraft lignin (quaternized LignoBoost®, CL) and anionic lignosulphonate (LS). The electrostatic attraction between positively charged CL and negatively charged LS led to the formation of insoluble self-organized macromolecule aggregates that align to films. The structures of the formed layers were evaluated by atomic force microscopy (AFM), firstly on glass lamina using dip-coating deposition and then on handsheets and industrial uncoated paper using roll-to-roll coating in a layer-by-layer mode. Coated samples were also characterized by optical microscopy, scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (SEM/EDS), and contact angle measurements. It was suggested that the structure of all-lignin aggregates is the result of the interaction of amphiphilic water-soluble lignin molecules leading to their specifically ordered mutual arrangement depending on the order and the mode of their application on the surface. The all-lignin coating of cellulosic fiber imparts lower air permeability and lower free surface energy to paper, mainly due to a decrease in surface polarity, thus promoting the paper’s hydrophobic properties. Moderate loading of lignin coating formulations (5–6 g m−2) did not affect the mechanical strength of the paper.

Herein is presented a novel and efficient portable paper-based sensing platform using paper-incorporated histidine stabilized gold nanoclusters (His-AuNCs), for the sensitive and selective detection of Fe ions from low-volume real water samples based on photoluminescence (PL) quenching. Highly photoluminescent colloidal His-AuNCs are obtained via a novel microwave-assisted method. The His-AuNCs-based sensor reveals a limit of detection (LOD) as low as 0.2 μM and a good selectivity towards Fe ions, in solution. Further, the fabricated portable sensing device based on paper impregnated with His-AuNCs proves to be suitable for the easy detection of hazardous Fe levels from real water samples, under UV light exposure, through evaluating the level of PL quenching on paper. Photographic images are thereafter captured with a smartphone camera and the average blue intensity ratio (I/I0) of the His-AuNCs-paper spots is plotted against [Fe2+] revealing a LOD of 3.2 μM. Moreover, selectivity and competitivity assays performed on paper-based sensor prove that the proposed platform presents high selectivity and accuracy for the detection of Fe ions from water samples. To validate the platform, sensing assays are performed on real water samples from local sources, spiked with 35 μM Fe ions (i.e., Fe2+). The obtained recoveries prove the high sensitivity and accuracy of the proposed His-AuNCs-paper-based sensor pointing towards its applicability as an easy-to-use, fast, quantitative and qualitative sensor suitable for on-site detection of toxic levels of Fe ions in low-volume real water samples.

Rapid, simple, and sensitive analysis of relevant proteins is crucial in many research areas, such as clinical diagnosis and biomarker detection. In particular, clinical data on cancer biomarkers show great promise in forming reliable predictions for early cancer diagnostics, although the current analytical systems are difficult to implement in regions of limited recourses. Paper-based biosensors, in particular, have recently received great interest because they meet the criteria for point-of-care (PoC) devices; the main drawbacks with these devices are the low sensitivity and efficiency in performing quantitative measurements. In this work, we design a low-cost paper-based nanosensor through plasmonic calligraphy by directly drawing individual plasmonic lines on filter paper using a ballpoint pen filled with gold nanorods (AuNR) as the colloidal ink. The plasmonic arrays were further successively coated with negatively and positively charged polyelectrolyte layers employed as dielectric spacers to promote the enhancement of the emission of carboxyl-functionalized quantum dots (QD)—previously conjugated with specific antibodies—for indirect detection of the carcinoembryonic antigen-related cell adhesion molecule 5 (CEACAM5). The efficiency, sensitivity, as well as the specificity of our portable nanosensor were validated by recording the luminescence of the QD@Ab complex when different concentrations of CEACAM5 were added dropwise onto the calligraphed plasmonic arrays.

Many orally administrated drugs exhibit poor bioavailability due to their limited solubility. The smartFilm technology is an innovative approach to improve the drug aqueous solubility, where the drug is embedded within the matrix of cellulose-based paper in an amorphous state, hence increasing its solubility. Despite its proven effectiveness, smartFilms, i.e., pieces of paper, exhibit limited flowability and are not easy to swallow, and thus oral administration is not convenient. In addition, there is a lack of knowledge of their mechanical behavior under compression. This study aimed to transform unloaded smartFilms, i.e., paper, into a flowable physical form and investigated its mechanical behavior when compressed. Granules made of paper were prepared via wet granulation and were compressed into tablets. The influence of using different amounts and forms of sucrose, as a binder, on the pharmaceutical properties of the produced granules and tablets was studied and the most suitable composition was identified by using instrumented die experiments. For this, the Poisson’s ratio and Young’s modulus were determined for different compaction force levels and the deformation behavior was estimated with the Heckel mathematical model. All granule batches showed good flowability with angle of repose values between 25–35°. Granule batches with ≤30% dry sucrose content produced tablets that fulfilled the European Pharmacopeia requirements, and the compaction behavior of the granules was found to be comparable to the behavior of classical binders and compression enhancers. Paper can be transferred into granules. These granules can be used as suitable intermediate products for the production of tablets made of paper in large, industrial scale.

(1) Background: Numerous oral drugs exhibit limited bioavailability due to their poor solubility and poor intestinal permeability. The smartFilm technology is an innovative approach that improves the drug aqueous solubility via incorporating the drug in an amorphous state into a cellulose-based matrix, i.e., paper. smartFilms can be transformed into a free-flowing physical form (i.e., paper granules) that can be compressed into tablets with optimum physico-chemical and pharmaceutical properties. The aim of this study was to investigate if smartFilm tablets are suitable for improved oral delivery of poorly water-soluble drugs. (2) Methods: Curcumin is a poorly soluble drug with low intestinal permeability and was used for the production of curcumin-loaded smartFilms. The curcumin-loaded smartFilms were transferred into smartFilm granules which were then compressed into curcumin-loaded smartFilm tablets. The tablets were characterized regarding their physico-chemical and pharmaceutical properties, and the intestinal permeability of curcumin was determined with the ex vivo porcine intestinal model. The ex vivo intestinal permeability of curcumin from the smartFilm tablets was compared to a physical mixture of curcumin and paper and to a classical and to an innovative commercial product, respectively. (3) Results: The produced curcumin-loaded smartFilm tablets fulfilled the European Pharmacopoeia requirements, incorporated curcumin in amorphous state within the cellulose matrix and exhibited an enhanced dissolution rate. The ex vivo intestinal permeation data were shown to correlate to the in vitro dissolution data. The ex vivo intestinal permeation of curcumin from the smartFilm tablets was about two-fold higher when compared to the physical mixture and the classical commercial product. No differences in the ex vivo bioavailability were found between the smartFilm tablets and the innovative commercial product. (4) Conclusions: smartFilm tablets are a cost-effective and industrially feasible formulation approach for the formulation of poorly water-soluble drugs, i.e., BCS class II and IV drugs.

Most power transformers are oil-immersed transformers for which its insulation system consists of oil and cellulosic solid. The insulation liquid impregnates the solid-covering air spaces, which improves the efficiency of the insulation system. Not only does the oil ensure electrical insulation but it also works as coolants transferring the heat generated during transformer operation to the exterior of the transformer. Throughout normal operation conditions, transformers experience multiple stresses that degrade their insulation. Since the lifetime of oil-immersed transformers is defined mainly by the state of the insulation paper, it is critical to understand the behavior and degradation mechanisms of new insulation systems that try to overcome the drawbacks of mineral oil as well as to improve power transformer performances. The current increased prevalence of the nonlinear loads additionally stresses power transformers, which generates their premature ageing or even failure. Consequently, new materials and assessment methods are required to guarantee the suitable management of power transformer populations. In this Special Issue “Experimental and Numerical Analysis of Thermal Ageing in Power Transformers”, four papers have been published. The guest editor also describes briefly some challenges involved beyond the coverage of this Special Issue.

Hydrogen sulfide (H2S) is known to participate in bacteria-induced inflammatory response in periodontal diseases. Therefore, it is necessary to quantify H2S produced by oral bacteria for diagnosis and treatment of oral diseases including halitosis and periodontal disease. In this study, we introduce a paper-based colorimetric assay for detecting bacterial H2S utilizing silver/Nafion/polyvinylpyrrolidone membrane and a 96-well microplate. This H2S-sensing paper showed a good sensitivity (8.27 blue channel intensity/μM H2S, R2 = 0.9996), which was higher than that of lead acetate paper (6.05 blue channel intensity/μM H2S, R2 = 0.9959). We analyzed the difference in H2S concentration released from four kinds of oral bacteria (Eikenella corrodens, Streptococcus sobrinus, Streptococcus mutans, and Lactobacillus casei). Finally, the H2S level in Eikenella corrodens while varying the concentration of cysteine and treatment time was quantified. This paper-based colorimetric assay can be utilized as a simple and effective tool for in vitro screening of H2S-producing ability of many bacteria as well as salivary H2S analysis.

The hydroxyl groups on the cellulose macromolecular chain cause the cellulose surface to have strong reactivity. In this study, 1H, 1H, 2H, 2H-perfluorodecyltriethoxysilane (PDOTES) was used to modify cellulose to improve its triboelectric properties, and a triboelectric nanogenerator (TENG) was assembled. The introduction of fluorine groups reduced the surface potential of cellulose and turned it into a negative phase, which enhanced the ability to capture electrons. The electrical properties increased by 30% compared with unmodified cellulose. According to the principles of TENGs, a self-powered human-wearable device was designed using PDOTES-paper, which could detect movements of the human body, such as walking and running, and facilitated a practical method for the preparation of efficient wearable sensors.

In the present society, the recycling and reuse of valuable substances are of utmost importance for economic and environmental purposes. At the same time, there is a pressing need to develop new methods to protect the ecosystem from many human activities, including those that have contributed to an ever-increasing presence of pharmaceutical pollutants. In this study, a straightforward approach that applies a magnetic carbon composite for the effective removal of NSAIDs from biological fluids is reported. The composite was produced by recycling wasted handkerchiefs, to provide cellulose to the reactive system and then transformed into carbon via calcination at high temperature. The morphological and structural features of the prepared “Fe3O4@-activated carbon” samples were investigated via thermal analysis, X-ray diffraction, Raman spectroscopy, and scanning electron microscopy. Magnetic solid-state extraction was carried out to reveal the adsorption capabilities of the magnetic carbon composite and then combined with UHPLC–PDA for the determination and quantification of five NSAIDs (furprofen, indoprofen, ketoprofen, flurbiprofen, and indomethacin). The method developed herein proved to be fast and accurate. The adsorbent could be reused for up to 10 cycles, without any decrease in performance; thus, it contributes to an intelligent and sustainable economic strategy projected toward minimal waste generation.

The purpose of this work is the study of laser cleaning of historical paper. The effect of laser exposure of the paper reflectance, fracture resistance and acidity was investigated. The paper surface roughness before and after laser treatment was analyzed by optical and scanning electron microscopy. It was shown that use of multi-pulse micromachining in combination with high-speed scanning of laser beams provides high safety for paper cleaning. The optimal parameters of laser radiation for effective and safe cleaning are a power density of about 2 × 105 W/cm2 at a wavelength of 1.06 μm, pulse repetition rate is 20 kHz; and a beam scanning speed of 200 mm/s–500 mm/s. The selective laser cleaning method for books and documents was proposed. Selective cleaning is achieved by means of high-precision control of the trajectory of movement of laser beams.

There is current interest in replacing petroleum-based additives in consumer paper products with abundantly available, renewable and sustainable biopolymers such as lignin-containing cellulose nanofibers (LCNFs) and cottonseed protein. This research characterized the performance of cottonseed protein isolate with/without LCNFs to increase the dry strength of filter paper. The application of 10% protein solution with 2% LCNFs as an additive improved the elongation at break, tensile strength and modulus of treated paper products compared to the improved performance of cottonseed protein alone. Improvements in tensile modulus and tensile strength were greatest for samples containing larger amounts of lignin and a greater degree of polymerization than for those with less lignin from the same biomass sources.

A current challenge regarding microfluidic paper-based analytical devices (µPAD) for blood plasma separation (BPS) and electrochemical immunodetection of protein biomarkers is how to achieve a µPAD that yields enough plasma to retain the biomarker for affinity biosensing in a functionalized electrode system. This paper describes the development of a BPS µPAD to detect and quantify the S100B biomarker from peripheral whole blood. The device uses NaCl functionalized VF2 filter paper as a sample collection pad, an MF1 filter paper for plasma retention, and an optimized microfluidic channel geometry. An inverted light microscope, scanning electron microscope (SEM), and image processing software were used for visualizing BPS efficiency. A design of experiments (DOE) assessed the device’s efficacy using an S100B ELISA Kit to measure clinically relevant S100B concentrations in plasma. The BPS device obtained 50 μL of plasma from 300 μL of whole blood after 3.5 min. The statistical correlation of S100B concentrations obtained using plasma from standard centrifugation and the BPS device was 0.98. The BPS device provides a simple manufacturing protocol, short fabrication time, and is capable of S100B detection using ELISA, making one step towards the integration of technologies aimed at low-cost POC testing of clinically relevant biomarkers.

Recycled paper fiber rejects have shown potential as a source of waste-to-resource carbohydrates for renewable chemicals production. This study examined three classes of recycled paper fines (old corrugated containers, old newspaper, and mixed office waste) and two industrial papermaking rejects streams from different recycling mills (one mill processes linerboard and the other old corrugated cardboard). The effect of chemical pretreatment using dilute sodium hydroxide, hot water and dilute sulfuric acid on enzymatic glucose and xylose yields was evaluated. Enzymatic hydrolysis results indicated that recycled fiber streams with more old corrugated cardboard have higher potential to produce carbohydrates. The recycled cardboard rejects produced more glucose and xylose per kilogram of rejects than the linerboard rejects under all untreated and pretreated conditions. The highest producing rejects sample was sodium hydroxide pretreated cardboard rejects with 373 g glucose and 61 g xylose produced per kilogram of rejects. However, a simple hot water pretreatment showed similar results, with 335 g glucose and 58 g xylose produced per kilogram of rejects. The hot water pretreatment is recommended due to its comparable yield and lower chemical addition.

Hydrophobic coatings are of utmost importance for many applications of paper-based materials. However, to date, most coating methods demand vast amounts of chemicals and solvents. Frequently, fossil-based coating materials are being used and multiple derivatization reactions are often required to obtain desired performances. In this work, we present a solvent-free paper-coating process, where olive oil as the main biogenic component is being used to obtain a hydrophobic barrier on paper. UV-induced thiol-ene photocrosslinking of olive oil was pursued in a solvent-free state at a wavelength of 254 nm without addition of photoinitiator. Optimum reaction conditions were determined in advance using oleic acid as a model compound. Paper coatings based on olive oil crosslinked by thiol-ene reaction reach water contact angles of up to 120°. By means of Fourier transform infrared spectroscopy and differential scanning calorimetry, a successful reaction and the formation of a polymer network within the coating can be proven. These results show that click-chemistry strategies can be used to achieve hydrophobic polymeric paper coatings while keeping the amount of non-biobased chemicals and reaction steps at a minimum.

In this study, the effect of air plasma on the surface properties of printed and coated cardboard was investigated. The material was activated by low-pressure cold plasma for 1, 10, 20, and 30 s. Wettability changes on the surface were examined by contact angle measurements using the sessile droplet technique. The differences in the surface free energy were calculated using the Lifshitz–van der Waals/acid–base and Contact Angle Hysteresis approaches. Optical profilometry was used for the surface roughness evaluation and an X-ray photoelectron spectroscopy analysis was performed to find changes in surface chemistry. Adhesive strength tests were carried out to estimate the adhesion changes after the material’s modification. It was found that the water and formamide contact angles increased after the plasma treatment while the diiodomethane contact angle did not change. As a result of the modification, the surface free energy also increased significantly and the surface roughness increased. The pull-off tests confirmed the improvement in the material’s surface properties. Moreover, it was demonstrated that the optimal effect can be obtained after just 10 s of the plasma process.

In this study, a paper-integrated analytical device that combined a paper-based colorimetric assay with a paper-based cell culture platform was developed for the in situ detection of hydrogen sulfide (H2S) in three-dimensional (3D)-cultured, live prostate cancer cells. Two kinds of paper substrates were fabricated using a simple wax-printing methodology to form the cell culture and detection zones, respectively. LNCaP cells were seeded directly on the paper substrate and grown in the paper-integrated analytical device. The cell viability and H2S production of LNCaP cells were assessed using a simple water-soluble tetrazolium salt colorimetric assay and H2S-sensing paper, respectively. The H2S-sensing paper showed good sensitivity (sensitivity: 6.12 blue channel intensity/μM H2S, R2 = 0.994) and a limit of quantification of 1.08 μM. As a result, we successfully measured changes in endogenous H2S production in 3D-cultured, live LNCaP cells within the paper-integrated analytical device while varying the duration of incubation and substrate concentration (L-cysteine). This paper-integrated analytical device can provide a simple and effective method to investigate H2S signaling pathways and drug screening in a 3D culture model.

An important step in the conservation of old paper documents is the analysis of both the medium and the ink, in an attempt first to determine the extent of deterioration and degradation and then to choose the best preservation and restoration solutions. Our paper focuses on the analysis of three old documents displayed at the ‘Poni-Cernătescu’ Museum in Iaşi City, Romania by optical microscopy (OM), scanning electron microscopy and energy dispersive X-ray spectroscopy (SEM-EDX), micro-FTIR spectroscopy and FT-Raman. Thus, the morphology and chemical composition of the paper media and the type of ink, as well as the cellulose crystallinity index were determined. PCA (Principal Component Analysis) was also used while relying on spectra collected by FTIR spectroscopy. We were able to determine the extent of degradation of the documents by corroborating all these findings.

Surface hydrophobicity and grease resistance of paper may be achieved by the application of coatings usually derived from fossil-oil resources. However, poor recyclability and environmental concerns on generated waste has increased interest in the study of alternative paper coatings. This work focuses on the study of the performances offered by two different biopolymers, poly(3-hydroxybutyrate-co-3hydroxyvalerate) (PHBV) and polycaprolactone (PCL), also assessing the effect of a plasticizer (PEG) when used as paper coatings. The coated samples were characterized for the structural (by scanning electron microscopy, SEM), diffusive (water vapor and grease barrier properties), and surface properties (affinity for water and oil, by contact angle measurements). Samples of polyethylene-coated and fluorinated paper were used as commercial reference. WVTR of coated samples generally decreased and PHBV and PCL coatings with PEG at 20% showed interesting low wettability, as inferred from the water contact angles. Samples coated with PCL also showed increased grease resistance in comparison with plain paper. This work, within the limits of its lab-scale, offers interesting insights for future research lines toward the development of cellulose-based food contact materials that are fully recyclable and compostable.

This work reports a modification of a fibrous cellulose material (paper) by the addition of polyacrylonitrile (PAN) fibres doped with 10,12–pentacosadiynoic acid (PDA). The fibres are sensitive to ultraviolet (UV) light. When the paper containing PAN–PDA is irradiated with UV light it changes colour to blue as a consequence of interaction of the light with PDA. The colour intensity is related to the absorbed dose, content of PAN–PDA fibres in the paper and the wavelength of UV radiation. The features of the paper are summarised after reflectance spectrophotometry and scanning microscopy analyses. All the properties of the modified paper were tested in accordance with adequate ISO standards. Moreover, a unique method for assessing the unevenness of the paper surface and the quality of printing was proposed by using a Python script (RGBreader) for the analysis of RGB colour channels. The modification applied to the paper can serve as a paper security system. The modified paper can act also as a UV radiation indicator.

Currently, there is an increasing interest in the use of biopolymers in industrial applications to replace petroleum-based additives, since they are abundantly available, renewable and sustainable. Cottonseed protein is a biopolymer that, when used as a modifier, has shown improved performance for wood adhesives and paper products. Thus, it would be useful to explore the feasibility of using cellulose nanomaterials to further improve the performance of cottonseed protein as a paper strength agent. This research characterized the performance of cottonseed protein isolate with/without cellulose nanofibers (CNFs) and cellulose nanocrystals (CNCs) to increase the dry strength of filter paper. An application of 10% protein solution with CNCs (10:1) or CNFs (50:1) improved the elongation at break, tensile strength and modulus of treated paper products compared to the improved performance of cottonseed protein alone. Further analysis using scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) indicated that the cottonseed protein/nanocellulose composites interacted with the filter paper fibers, imparting an increased dry strength.

The use of paper as a sustainable packaging material is favored, but it lacks sufficient barrier properties in terms of water repellence and oil resistance. Novel approaches consider active packaging materials or coatings with controlled release providing additional functionality for delivery of specific components to the surface. In this study, the development of a waterborne coating with organic nanoparticles and encapsulated sunflower oils is presented as a system for thermal release of the oil and on-demand tuning of the final barrier properties of the paper substrate. After synthesis of the nanoparticles, it seems that the encapsulation of various grades of sunflower oil (i.e., either poly-unsaturated or mono-unsaturated) strongly affects the encapsulation efficiency and thermal release profiles. The water contact angles are controlled by the oil release and chemical surface composition of the coating upon thermal heating. The oil resistance of the paper improves as a more continuous oil film is formed during thermal release. In particular, the chemical surface composition of the paper coatings is detailed by means of micro-Raman spectroscopy and surface imaging, which provide an analytical quantification tool to evaluate surface coverage, oil delivery, and variations in organic coating moieties.

Cellulose is a promising biomass material suitable for high volume applications. Its potential lies in sustainability, which is becoming one of the leading trends in industry. However, there are certain drawbacks of cellulose materials which limit their use, especially their high wettability and low barrier properties, which can be overcome by applying thin coatings. Plasma technologies present a high potential for deposition of thin environmentally friendly and recyclable coatings. In this paper, two different plasma reactors were used for coating two types of cellulose-based substrates with hexamethyldisiloxane (HMDSO). The changes in surface characteristics were measured by atomic force microscopy (AFM), scanning electron microscopy (SEM), surface free energy and contact angles measurements, X-ray photoelectron spectroscopy (XPS), and secondary ion mass spectrometry (SIMS). Successful oleofobization was observed for an industrial scale reactor where pure HMDSO was used in the absence of oxygen.

This paper is aimed at investigating the usage of biosynthesized poly(3-hydroxybutyrate) (P(3-HB)) for a coating on pineapple leaf fiber paper (PLFP). For this purpose, (P(3-HB)) was produced by Rhodococcus pyridinivorans BSRT1-1, a highly potential P(3-HB) producing bacterium, with a weight-average molecular weight (Mw) of 6.07 × 10 −5 g/mol. This biosynthesized P(3-HB) at 7.5% (w/v) was then coated on PLFP through the dip-coating technique with chloroform used as a solvent. The respective coated PLFP showed that P(3-HB) could be well coated all over on the PLFP surface as confirmed by scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy. The brightness and mechanical properties of PLFP could be improved by coating with biosynthesized P(3-HB) in comparison to commercially available P(3-HB) and non-coated PLFP. Furthermore, coating of P(3-HB) significantly increased the water drop penetration time on the surface of PLFP and was similar to that of the commercial P(3-HB) with the same content. The results showed that all the coated PLPF samples can be degraded under the soil burial test conditions. We have demonstrated that the P(3-HB) coated PLFP paper has the ability to prevent water drop penetration and could undergo biodegradation. Taken together, the P(3-HB) coated PLFP can be applied as a promising biodegradable paper packaging.

Invasive alien plant species (IAPS) are one of the biggest challenges in European ecosystems, displacing local vegetation, destroying agricultural land, and causing billions of dollars of damage to the European economy every year. Many of them are removed daily and mainly burned. In this work, we investigated the possibilities of using plants as feedstock for paper production. Papers made from three invasive alien plants, i.e., Knotweed, Goldenrod, and Black locust, were studied and compared with commercial office paper. The study included testing of: (1) structural properties—basic physical properties, grammage, thickness, density and specific volume, moisture content, and ash content; (2) physical and dynamic mechanical properties—tensile strength, Clark stiffness, viscoelastic properties; (3) colorimetric properties of prints; (4) effect of UV light on ageing; and (5) study of cellulose fiber structure and morphology by microscopy. The results suggested that the paper produced can be used as commercial office paper, considering that the paper is slightly dyed. Such papers can also be used for special purposes that present a natural style and connection to nature. The papers produced can also be used for printing documents that are meant to be kept.

Airflow sensor is a crucial component for monitoring environmental airflow conditions in many engineering fields, especially in the field of aerospace engineering. However, conventional airflow sensors have been suffering from issues such as complexity and bulk in structures, high cost in fabrication and maintenance, and low stability and durability. In this work, we developed a facile direct-writing method for fabricating a low-cost piezoresistive element aiming at high-performance airflow sensing, in which a commercial pen was utilized to drop solutions of single-walled carbon nanotubes onto tissue paper to form a piezoresistive sensing element. The encapsulated piezoresistive element was tested for electromechanical properties under two loading modes: one loading mode is the so-called pressure mode in which the piezoresistive element is pressed by a normal pressure, and another mode is the so-called bending mode in which the piezoresistive element is bended as a cantilever beam. Unlike many other developed airflow sensors among which the sensing elements are normally employed as cantilever beams for facing winds, we designed a fin structure to be incorporated with the piezoresistive element for airflow sensing; the main function of the fin is to face winds instead of the piezoresistive element, and subsequently transfer and enlarge the airflow pressure to the piezoresistive element for the normal pressure loading mode. With this design, the piezoresistive element can also be protected by avoiding experiencing large strains and direct contact with external airflows so that the stability and durability of the sensor can be maintained. Moreover, we experimentally found that the performance parameters of the airflow sensor could be effectively tuned by varying the size of the fin structure. When the fin sizes of the airflow sensors were 20 mm, 30 mm, and 40 mm, the detection limits and sensitivities of the fabricated airflow sensors were measured as 8.2 m/s, 6.2 m/s, 3.2 m/s, 0.0121 (m/s)−2, 0.01657 (m/s)−2, and 0.02264 (m/s)−2, respectively. Therefore, the design of the fin structure could pave an easy way for adjusting the sensor performance without changing the sensor itself toward different application scenarios.

We propose a unique soft actuator—a paper actuator—based on carbon-nanotube-composite paper (CNT-composite paper), which is a composite of carbon nanotubes (CNTs) and paper. CNT-composite paper has highly efficient properties because of the contained CNTs, such as high electrical conductivity and semiconducting properties. We are considering using CNT-composite paper for various devices. In this study, we successfully developed a paper actuator. We determined the structure of the paper actuator by referencing that of bucky-gel actuators. The actuator operates using the force generated by the movement of ions. In addition to making the paper actuator, we also attempted to improve its performance, using pressure as an index and an electronic scale to measure the pressure. We investigated the optimal dispersant for use in paper actuators, expecting the residual dispersant on the CNT-composite paper to affect the performance differently depending on the type of dispersant. Referring to research on bucky-gel actuators, we also found that the addition of carbon powder to the electrode layers is effective in improving the pressure for paper actuators. We believe that the paper actuator could be used in various situations due to its ease of processing.

Hemp is a sustainable, recyclable, and high-yield annual crop that can be used to produce textiles, plastics, composites, concrete, fibers, biofuels, bionutrients, and paper. The integration of microfluidic paper-based analytical devices (µPADs) with hemp paper can improve the environmental friendliness and high-throughputness of µPADs. However, there is a lack of sufficient scientific studies exploring the functionality, pros, and cons of hemp as a substrate for µPADs. Herein, we used a desktop pen plotter and commercial markers to pattern hydrophobic barriers on hemp paper, in a single step, in order to characterize the ability of markers to form water-resistant patterns on hemp. In addition, since a higher resolution results in densely packed, cost-effective devices with a minimized need for costly reagents, we examined the smallest and thinnest water-resistant patterns plottable on hemp-based papers. Furthermore, the wicking speed and distance of fluids with different viscosities on Whatman No. 1 and hemp papers were compared. Additionally, the wettability of hemp and Whatman grade 1 paper was compared by measuring their contact angles. Besides, the effects of various channel sizes, as well as the number of branches, on the wicking distance of the channeled hemp paper was studied. The governing equations for the wicking distance on channels with laser-cut and hydrophobic side boundaries are presented and were evaluated with our experimental data, elucidating the applicability of the modified Washburn equation for modeling the wicking distance of fluids on hemp paper-based microfluidic devices. Finally, we validated hemp paper as a substrate for the detection and analysis of the potassium concentration in artificial urine.

In the era of big data and artificial intelligence, public datasets are becoming increasingly important for researchers to build and evaluate their models. This paper presents the FIKWaste dataset, which contains time series data for the volume of waste produced in three restaurant kitchens in Portugal. Organic (undifferentiated) and inorganic (glass, paper, and plastic) waste bins were monitored for a consecutive period of four weeks. In addition to the time series measurements, the FIKWaste dataset contains labels for waste disposal events, i.e., when the waste bins are emptied, and technical and non-technical details of the monitored kitchens.

One of the main problems faced by libraries, archives and collectors is the mold degradation of the paper-based documents, books, artworks etc. Microfungi (molds) emerge in regular storage conditions of such items (humidity, usually over 50%, and temperatures under 21 °C). If the removal of the visible mycelium is relatively easy, there is always the problem of the subsequent appearance of mold as the spores remain trapped in the cellulosic, fibrillary texture, which acts as a net. Moreover, due to improper hand hygiene bacteria contamination, old books could represent a source of biohazard, being colonized with human pathogens. An easy and accessible method of decontamination, which could offer long term protection is therefore needed. Here, we present a facile use of the ZnO nanopowders as antimicrobial agents, suitable for cellulose-based products, conferring an extended antibacterial and anti-microfungal effect. The proposed method does not adversely impact on the quality of the cellulose documents and could be efficiently used for biodegradation protection.

As one of the most abundant natural polymers in nature, polysaccharides have the potential to replace petroleum-based polymers that are difficult to degrade in paper coatings. Polysaccharide molecules have a large number of hydroxyl groups that can bind strongly with paper fibers through hydrogen bonds. Chemical modification can also effectively improve the mechanical, barrier, and hydrophobic properties of polysaccharide-based coating layers and thus can further improve the related properties of coated paper. Polysaccharides can also give paper additional functional properties by dispersing and adhering functional fillers, e.g., conductive particles, catalytic particles or antimicrobial chemicals, onto paper surface. Based on these, this paper reviews the application of natural polysaccharides, such as cellulose, hemicellulose, starch, chitosan, and sodium alginate, and their derivatives in paper coatings. This paper analyzes the improvements and influences of chemical structures and properties of polysaccharides on the mechanical, barrier, and hydrophobic properties of coated paper. This paper also summarizes the researches where polysaccharides are used as the adhesives to adhere inorganic or functional fillers onto paper surface to endow paper with great surface properties or special functions such as conductivity, catalytic, antibiotic, and fluorescence.

Screen-printing technology has revolutionized many fields, including that of electrochemical biosensing. Due to their current relevance, this review, unlike other papers, discusses the relevant aspects of electrochemical biosensors manufactured using this technology in connection to both paper substrates and wearable formats. The main trends, advances, and opportunities provided by these types of devices, with particular attention to the environmental and biomedical fields, are addressed along with illustrative fundamentals and applications of selected representative approaches from the recent literature. The main challenges and future directions to tackle in this research area are also pointed out.