Search

This paper details the development and verification tests of an open-source code named hy2LPTFoam intended for solving high-speed non-equilibrium gas-particle flows in OpenFOAM. The solver, based on hy2Foam for high-speed non-equilibrium gas flow, integrates multiple particle force models, heat transfer models, the diffusion-based smoothing method, and the MPPIC method. The verification tests incorporate interactions between shock waves and particle curtains with varying particle volume fractions, a JPL nozzle generating a two-phase gas–particle flow, and a Mars entry body with two particle inflow mass fractions. The tests yield good physical agreement with numerical and experimental data from the literature. [ABSTRACT FROM AUTHOR]

In order to determine the installation position of the front fin on the example rocket forebody, an optimized method based on a comprehensive evaluation indicator and variable step search is presented. The comprehensive indicator consists of four weight coefficients, two lateral aerodynamic forces and two aerodynamic moments. The computational fluid dynamics method based on a shear stress transport turbulence model is established to analyze the flow field characteristics of the forebody. The results indicate that under equal weight coefficients, the presented search algorithm can provide an optimized solution for the front fin to achieve the minimum value of the comprehensive evaluation indicator. When the range of the current wing movement changes or the weight coefficient distribution changes, this search algorithm can still provide the optimal solution and some feasible solutions. Under the given conditions, there is a difference between the optimal solution of the aerodynamic force priority and that of the aerodynamic moment priority. For the case of the aerodynamic moment priority, the mean level of the pressure coefficient corresponding to the optimal solution on the given observation plane is low. The presented method is effective in learning the appropriate installation position of the rocket's front fins. [ABSTRACT FROM AUTHOR]

High-speed global surface temperature distributions and heat flux measurements on the Initial Concept 3.X vehicle (IC3X) model were investigated at the UTSA Mach 7 wind tunnel, examining angles of attack of 0° and 5° at a freestream unit Reynolds number (Re) ~7 × 106 m−1. A ruthenium-based, fast-responding, temperature-sensitive paint (fast-TSP) prepared in-house was applied to a 7.1% scale model of the vehicle. Static calibration was performed to convert the intensity measurements into surface temperature values. The surface temperatures and derived heat flux fields conformed to the predicted trends, which was corroborated by Schlieren flow visualization. Notably, the average surface temperature variation was identified to range from 6 to 34 K at a 0° angle of attack and from 11 to 44 K at a 5° angle of attack, with the most pronounced gradient detected at the stagnation point. Additional measurements provided a detailed thermal assessment of the model, including estimations of the stagnation point heat flux, the convective heat transfer coefficient, and the modified Stanton number. Statistical and time series analyses of the data collected revealed the absence of prevailing unsteady phenomena, suggesting that the tested design geometry is well suited for hypersonic flight applications. These experimental outcomes not only shed light on the aerothermodynamics experienced during high-speed flight but also underscore the effectiveness of fast-TSP in capturing both quantitative and qualitative thermal data. [ABSTRACT FROM AUTHOR]

The parametric design method is widely utilized in the preliminary design stage for hypersonic vehicles; it ensures the fast iteration of configuration, generation, and optimization. This study proposes a novel parametric method for a wide-range, wing-morphing glide vehicle. The whole configuration, including a waverider fuselage, a rotating wing, a blunt leading edge, rudders, etc., can be easily described using 27 key parameters. In contrast to the typical parametric method, the new method takes internal payloads into consideration during the shape optimization process. That is, the vehicle configuration can be flexibly adjusted depending on the internal payloads; these payloads may be of random amounts and have different shapes. The code for the new parametric design method is developed using the secondary development tools of UG (UG 10.0) commercial software. The lift and drag characteristics over a wide operational range (H = 6–25 km, M = 2.5–8.5, AOA = 0–10°) were numerically investigated, as was the influence of the retracting angle of the morphing wings. It was found that, for the mode of the fully deployed wings, the lift-to-drag ratio (L/D) remained at a high level (≥4.7) over a Mach range of 4.0–8.5 and an AOA range of 4–7°. For the mode of the fully retracted wings, the drag coefficient remained smaller than 0.02 over a Mach range of 4.0–8.5 and an AOA range of 0–5°. A wide L/D of 0.3–4.7 could be achieved by controlling the retracting angle of the wings, thus demonstrating a good potential for flight maneuverability. The flexible change in L/D proved to be a combined result of varying pressure distribution and edge-flow spillage. This will aid in the further optimization of lift/drag characteristics. [ABSTRACT FROM AUTHOR]

Explorations involving long-endurance and maneuvering flights in the upper atmosphere, as well as research on atmospheric entries of space debris or asteroids, call for a full understanding of hypersonic rarefied flows. The inverse Magnus effect occurs in the hypersonic rarefied flow past a rotating sphere, but the aerodynamic behavior is contrary to the Magnus effect in the continuum flow regime. In this article, a series of such flows are numerically studied using the direct simulation Monte Carlo (DSMC) method. By analyzing the flow fields, as well as the distributions of pressure and shear stress on the sphere, the formation of the inverse Magnus force can be attributed to the tangential momentum transfer between incident gas molecules and the windward surface. The variation laws of aerodynamic parameters with the rotation rate are presented and discussed. [ABSTRACT FROM AUTHOR]

The double-wedge configuration is a typical characteristic shape of the rudder surface of high-speed aircraft. The impact of the shock wave/boundary layer interaction and the shock wave/shock wave interaction resulting from the double wedge on aircraft aerodynamics cannot be ignored. The aerodynamic performance of the aircraft would be seriously affected. Accordingly, to reduce the wave drag, and to relieve the thermal load and pressure load, flow control is required for the shock wave/shock wave interaction and the shock wave/boundary layer interaction induced by the double-wedge configuration. In this paper, double-wedge shock wave/shock wave interaction is controlled by a high-energy surface arc discharge array and observed by high-speed schlieren flow field measurement at Mach 8. The 30-channel discharge array is set on the primary wedge plane, and actuation is generated. Hypersonic V shock wave/shock wave interaction is effectively controlled by the shock wave array induced by the high-energy surface arc discharge array, which makes the shock wave/shock wave interaction structure disappear or intermittent. The potential control mechanism is to reduce strong shock wave interaction by transforming the type of shock wave interaction. Therefore, the ability of plasma array actuation to control complex shock wave/shock wave interaction is verified, which provides a new method for hypersonic shock wave/shock wave interaction control. [ABSTRACT FROM AUTHOR]

Compression corner shock wave/boundary layer interaction (SWBLI) is a typical shock wave/boundary layer interaction (SWBLI) problem in supersonic/hypersonic flows. In previous studies, the separation flow is usually caused by a single shock wave. However, in the actual aircraft surface configuration, two-stage compression or even multistage compression will produce more complex SWBLI problems. The multi-channel shock structure makes the flow field structure more complicated and also puts forward higher requirements for the flow control scheme. In order to explore a flow control method for the double compression corner shock wave/boundary layer interaction problem, an experimental study is carried out to control the double compression corner shock wave/boundary layer interaction with a high-energy flow pulsed arc discharge array under the condition that the incoming flow velocity Ma 6.0 has both noise flow fields and quiet flow fields. The results show that when UDC = 0.5 kV actuation is applied, the influence range of the hot gas mass flow direction is about 65 mm, which can weaken the shock wave intensity to a certain extent. When UDC = 1 kV actuation is applied, the influence range of the hot gas mass flow direction extends to 85 mm, and the actuation has a significant control effect on the flow field. Through spatio-temporal evolution analysis and spatial gradient threshold processing of high-speed schlieren images of actuated flow fields, the feasibility of controlling the hypersonic double compression corner shock wave/boundary layer interaction by using a high-energy flow pulsed arc discharge array is verified. The control law of a high-energy flow pulsed arc discharge array acting on the double compression corner shock wave/boundary layer interaction is revealed. [ABSTRACT FROM AUTHOR]

Significant thermochemical nonequilibrium effects always exist in the flow field around hypersonic vehicle at extreme flight condition. Previous studies have proposed various thermodynamic and chemical kinetic models to describe the thermochemical nonequilibrium processes in hypersonic and high-temperature flow. However, different selections from such models might lead to remarkable variations in computational burden and prediction accuracy, which is still a matter of being unclear. In the present study, different commonly studied models for calculating the thermochemical nonequilibrium are systematically evaluated. The 5-, 7- and 11-species chemical kinetic models of Dunn-Kang, Gupta and Park together with the one- and two-temperature models are employed respectively to simulate the hypersonic flows over a standard cylinder with the radius of 1 m by HyFLOW, which is a commercial software based on the numerical solution of Navier-Stokes equations. Three flight conditions of FIRE Ⅱ classical flight trajectory are employed in the study. It shows that the differences between the results of the Dunn-Kang, Gupta and Park chemical kinetic models with the same number of species are small, but the Gupta model predicts the most conservative values of the wall heat flux. When only the order of magnitude and distribution trends of the pressure and wall heat flux are concerned, the one-temperature model combined with 5-species chemical reaction model can be used for a rapid prediction. While the accurate flow solution is required, the two-temperature model conjugated with Gupta 11-species model is recommended, especially at the conditions of extremely high altitude and Mach number. [ABSTRACT FROM AUTHOR]

The waverider is widely used in hypersonic vehicles with its high aerodynamic performance, but due to the serious aerothermal environment, its sharp leading edge should be blunted. Circular blunt is one of the commonly used aerothermal characteristic protection methods. Circular blunt with larger diameter can reduce peak heat flux, but at the same time, it will lead to larger drag. The existing research shows that under the same blunt diameter in two-dimensions, the non-uniform blunt can reduce the peak heat flux by 20%, and the difference of drag is small. In this paper, the non-uniform blunt profile is applied to the three-dimensional waverider, and the influence of the non-uniform blunt profile on the aerothermal characteristic performance and aerodynamic performance of the waverider is studied, and the results are compared with those of circular blunt. The numerical simulation is used to compare and analyze the waverider under different angles of attack, flight altitudes, and Mach number. The results show that the peak heat flux of the waverider with non-uniform blunt reduces by about 17% compared with that with circular blunt under a small angle of attack range, Mach 2-10, and a flight altitude of 15–35 km. Meanwhile, when the blunt height/diameter is 20 mm, the aerodynamic performance difference between the two different blunt profiles does not exceed 3% within a 15 degrees angle of attack, Mach 2-10, and flight altitude of 15–35 km. The non-uniform blunt profile can be applied to the design of the three-dimensional waverider. [ABSTRACT FROM AUTHOR]

In order to improve the thermal protection performance of the active thermal protection system (TPS) based on the spike and jet, an adjustable non-ablative thermal protection system, of which the spike can be rotated in the direction of the free stream, is proposed in this paper. The thermal protection mechanism and the optimal installation angle are analyzed by adopting the numerical method. The results show that the angle of attack has great influence on the peak heat flux of hypersonic vehicles, the dangerous point is on the windward side of the vehicles at the non-zero angle of attack. With the increase in angle of attack, the heat flux of the windward side of the vehicles rises rapidly, leading to the decrease in the global thermal protection efficiency. The adjustable non-ablative TPS in this paper greatly reduces the aeroheating of the windward side through the installation angle between the spike and nose cone, thus improving the global thermal protection efficiency. The optimal installation angle can be obtained by numerical or experimental methods in engineering design, and the difference between the angle of attack and the optimal installation angle is about 2.4° for the proposed model. Therefore, the installation angle can be automatically adjusted based on the angle of attack to achieve the highest thermal protection efficiency. [ABSTRACT FROM AUTHOR]

Energy deposition for flow and flight control has received significant interest in the past several decades due to its potential application to high-speed flow and flight control. This paper reviews recent progress and recommends future research. [ABSTRACT FROM AUTHOR]

The characteristics of aero-thermoelastic coupling are important for the design of the leading edge in hypersonic vehicles. Herein, a fluid–structure interaction analysis is performed to study the leading edge of a hypersonic vehicle using aero-thermoelastic coupling methods. The results show that the maximum heat flux and temperature of the optimized Bézier curve leading edge are reduced to a certain extent, compared with a hemi-cylindrical leading edge, and the lift–to–drag ratios of the two models are close. The Bézier curve leading-edge model can reduce the blunt radius of the leading edge of the hypersonic vehicle and increase the aerodynamic performance without losing thermal performance. [ABSTRACT FROM AUTHOR]

This study explored the applications of liquid hydrogen (LH2) in aerospace projects, followed by an investigation into the efficiency of ramjets, scramjets, and turbojets for hypersonic flight and the impact of grey, blue, and green hydrogen as an alternative to JP-7 and JP-8 (kerosene fuel). The advantage of LH2 as a propellant in the space sector has emerged from the relatively high energy density of hydrogen per unit volume, enabling it to store more energy compared to conventional fuels. Hydrogen also has the potential to decarbonise space flight as combustion of LH2 fuel produces zero carbon emissions. However, hydrogen is commonly found in hydrocarbons and water and thus it needs to be extracted from these molecular compounds before use. Only by considering the entire lifecycle of LH2 including the production phase can its sustainability be understood. The results of this study compared the predicted Life Cycle Assessment (LCA) emissions of the production of LH2 using grey, blue, and green hydrogen for 2030 with conventional fuel (JP-7 and JP-8) and revealed that the total carbon emissions over the lifecycle of LH2 were greater than kerosene-derived fuels. [ABSTRACT FROM AUTHOR]

The substantial aerodynamic drag and severe aerothermal loads, which are closely related to boundary layer transition, challenge the design of hypersonic vehicles and could be relieved by active methods aimed at drag and heat flux reduction, such as aerodisk. However, the research of aerodisk effects on transitional flows is still not abundant. Based on the improved k-ω-γ transition model, this study investigates the influence of the aerodisk with various lengths on hypersonic boundary layer transition and surface heat flux distribution over HIFiRE-5 configuration under various angles of attack. Certain meaningful analysis and results are obtained: (i) The existence of aerodisk is found to directly trigger separation-induced transition, moving the transition onset near the centerline upstream and widening the transition region; (ii) The maximum wall heat flux could be effectively reduced by aerodisk up to 52.1% and the maximum surface pressure can even be reduced up to 80.4%. The transition shapes are identical, while the variety of growth rates of intermittency are non-monotonous with the increase in aerodisk length. The dilation of region with high heat flux boundary layer is regarded as an inevitable compromise to reducing maximum heat flux and maximum surface pressure. (iii) With the angle of attack rising, first, the transition is postponed and subsequently advanced on the windward surface, which is in contrast to the continuously extending transition region on the leeward surface. This numerical study aims to explore the effects of aerodisk on hypersonic boundary layer transition, enrich the study of hypersonic flow field characteristics and active thermal protection system considering realistic boundary layer transition, and provide references for the excogitation and utilization of hypersonic vehicle aerodisk. [ABSTRACT FROM AUTHOR]

Transitional flow has a significant impact on vehicles operating at supersonic and hypersonic speeds. An economic way to simulate this problem is to use computational fluid dynamics (CFD) codes. However, not all CFD codes can solve transitional flows. This paper examines the ability of the Spalart–Allmaras one-equation BCM (SA-BCM) transitional model to solve hypersonic transitional flow, implemented in the open-source CFD code Eilmer. Its performance is validated via existing wind tunnel data. Eight different hypersonic flow conditions are applied. A flat plate model is built for the numerical tests. The results indicate that the existing SA-BCM model is sensitive to the freestream turbulence intensity and the grid size. It is not accurate in all the test cases, though the transitional length can be matched by tuning the freestream intensity. This is likely due to the intermittency term of the SA-BCM model not being appropriately calibrated for high-velocity flow, though if the model can be recalibrated it may be able to solve the general high-velocity flows. Although the current SA-BCM model is only accurate under certain flow conditions after one calibration process, it remains attractive to CFD applications. As a one-equation model, the SA-BCM model runs much faster than multiple-equation flow models. [ABSTRACT FROM AUTHOR]

Hypersonic vehicles are drawing more and more attention now and for the near future, especially in the low-altitudes near space, from 20 km to 45 km. The reliable separation of the protecting shroud from the hypersonic vehicle is a prerequisite and critical issue for the success of the entire flight mission. The unsteady multi-body separation characteristics and flow characteristics of hypersonic shroud separation at Mach 7.0 are investigated based on numerical simulation in this paper. The improved delayed detached eddy simulation (IDDES) method, dynamic hybrid overset mesh method, and HLLE++ numerical scheme are used to ensure numerical accuracy. Numerical results show that there are four types of vortexes and three types of shock waves inside the shrouds during the separation process, which generate complex shock wave/vortex/boundary layer interactions. Further, an unsteady process of the expansion-transfer-dissipation of an A-type vortex is found, which is the result of strong shock/vortex/boundary layer interactions. The adverse pressure gradient is the root cause driving the generation and transfer of the A-type vortex during the shroud separation. Furthermore, the transfer process of the A-type vortex only lasts for 5.52 ms but causes a large disturbance to the aerodynamic force of the shroud. The results of this paper could provide a reference for the design of near-space hypersonic vehicles. [ABSTRACT FROM AUTHOR]

An experimental investigation was performed on the wake flow field of an isolated roughness element of a flat plate at Mach 6 by employing the nanoparticle-based planar laser scattering (NPLS) approach. The three-dimensional features and causes of the flow field structure were scrutinized by transient flow field images of roughness elements on various planes. The time-resolved NPLS technique was implemented to examine the time evolution characteristics of the wake flow field of roughness elements. In the following, the process of dynamic evolution of large-scale vortex structures in the wake flow field was methodically assessed. Additionally, the influences of roughness element heights on the wake vortex structure were evaluated and the obtained results were compared. [ABSTRACT FROM AUTHOR]

Utilization of a heat source to regulate the shock wave–boundary layer interaction (SWBLI) of hypersonic inlets during throttling was computationally investigated. A plug was installed at the intake isolator's exit, which caused throttling. The location of the heat source was established by analysing the interaction of the shockwave from the compression ramp and the contact spot of the shockwave with that of the inlet cowl. Shockwave interaction inside the isolator was investigated using steady and transient cases. The present computational work was validated using previous experimental work. The flow distortion (FD) and total pressure recovery (TPR) of the inflows were also studied. We found that varying the size and power of the heat source influenced the shockwaves that originated around it and affected the SWBLI within the isolator. This influenced most of the performance measures. As a result, the TPR increased and the FD decreased when the heat source was applied. Thus, the use of a heat source for flow control was found to influence the performance of hypersonic intakes. [ABSTRACT FROM AUTHOR]

Strong viscous interaction and multiple flow regimes exist when vehicles fly at high altitude and high Mach number conditions. The Navier–Stokes(NS) solver is no longer applicable in the above situation. Instead, the direct simulation Monte Carlo (DSMC) method or Boltzmann model equation solvers are usually needed. However, they are computationally more expensive than the NS solver. Therefore, it is of great engineering value to establish the aerodynamic prediction model of vehicles at high altitude and high Mach number conditions. In this paper, the hypersonic aerodynamic characteristics of an X38-like vehicle in typical conditions from 70 km to 110 km are simulated using the unified gas kinetic scheme (UGKS), which is applicable for all flow regimes. The contributions of pressure and viscous stress on the force coefficients are analyzed. The viscous interaction parameters, Mach number, and angle of attack are used as independent variables, and the difference between the force coefficients calculated by UGKS and the Euler solver is used as a dependent variable to establish a nonlinear viscous interaction model between them in the range of 70–110 km. The evaluation of the model is completed using the correlation coefficient and the relative orthogonal distance. The conventional viscous interaction effect and rarefied effect are both taken into account in the model. The model can be used to quickly obtain the hypersonic aerodynamic characteristics of X38-like vehicle in a wide range, which is meaningful for engineering design. [ABSTRACT FROM AUTHOR]

In this paper, an opposing jet is applied to the space shuttle arc leading edge and the lifting body cone leading edge in the hypersonic condition of the rarefied flow field. The DSMC numerical algorithm is used to simulate and analyze the underlying working physics of the opposing jet. The results provide a reference for designing hypersonic vehicles in near space that reduce drag and protect against heat. [ABSTRACT FROM AUTHOR]

Accurate prediction of the aerothermal environment is of great significance to space exploration and return missions. The canonical Fire II trajectory points are simulated to investigate the radiative transfer in the shock layer for Earth reentry at hypervelocity above 10 km/s using a developed radiation–flowfield uncoupling method. The thermochemical nonequilibrium flow is solved by an in-house PHAROS Navier–Stokes code, while the nongray radiation is integrated by the tangent slab approximation, respectively, combined with the two-, five-, and eight-step models. For the convective heating, the present results agree well with the data of Anderson's relation. For the radiative heating, the two-step model predicts the closest values with the results of Tauber and Sutton's relationship, while the five- and eight-step models predict far greater. The three-step models all present the same order of magnitude of radiative heating of 1 MW/m2 and show a consistent tendency with the engineering estimation. The Planck-mean absorption coefficient is calculated to show the radiative transfer significantly occurs in the shock layer. By performing the steady simulation at each flight trajectory point, the present algorithm using a nongray step model with moderate efficiency and reasonable accuracy is promising to solve the real-time problem in engineering for predicting both convective and radiative heating to the atmospheric reentry vehicle in the future. [ABSTRACT FROM AUTHOR]

Robust fast-response transient calorimeters with novel calorimeter elements have attracted the attention of researchers as new synthetic materials have been developed. This sensor uses diamonds as the calorimeter element, and a platinum film resistance is sputtered on the back to measure the temperature. The surface heat flux is obtained based on the calorimetric principle. The sensor has the advantages of high sensitivity and not being prone to erosion. However, non-ideal conditions, such as heat dissipation from the calorimeter element to the surroundings, can lead to measurement deviation and result in challenges for sensor miniaturization. In this study, a novel transient calorimeter (NTC) with two different sizes was developed using air or epoxy as the back-filling material. Numerical simulations were conducted to explain the complex heat exchange between the calorimeter element and its surroundings, which showed that it deviated from the assumption of an ideal calorimeter sensor. Accordingly, a dynamic correction method was proposed to compensate for the energy loss from the backside of the calorimeter element. The numerical results showed that the dynamic correction method significantly improved the measurement deviation, and the relative error was within 2.3% if the test time was smaller than 12 ms in the simulated cases. Detonation shock tunnel experiments confirmed the results of the dynamic correction method and demonstrated a practical method to obtain the dynamic correction coefficient. The accuracy and feasibility of the dynamic correction method were verified in a single detonation shock tunnel and under shock tube conditions. The NTC calorimeter exhibited good repeatability in all experiments. [ABSTRACT FROM AUTHOR]

We investigate the propagation of elastic waves in a one-dimensional (1D) phononic crystal constituted by high aspect ratio epoxy nanoridges that have been deposited at the surface of a glass substrate. With the help of the finite element method (FEM), we calculate the dispersion curves of the modes localized at the surface for propagation both parallel and perpendicular to the nanoridges. When the direction of the wave is parallel to the nanoridges, we find that the vibrational states coincide with the Lamb modes of an infinite plate that correspond to one nanoridge. When the direction of wave propagation is perpendicular to the 1D nanoridges, the localized modes inside the nanoridges give rise to flat branches in the band structure that interact with the surface Rayleigh mode, and possibly open narrow band gaps. Filling the nanoridge structure with a viscous liquid produces new modes that propagate along the 1D finite height multilayer array. [ABSTRACT FROM AUTHOR]

For the past several decades, research dealing with hypersonic flight regimes has been restricted mainly to military applications. Hypersonic transportation could be a possible and affordable solution to travel in the medium term and there is renewed interest from several private organisations for commercial exploitation in this direction. Various combined cycle propulsion configurations have been proposed and the present paper deals with implications for the nozzle component of a ramjet configuration as part of one such combined cycle propulsion configuration. An investigation was undertaken for a method of turbine-based propulsion which enables the hypersonic vehicle to take off under its own power and propel the aircraft under different mission profiles into ramjet operational Mach regimes. The present study details an optimal method of ramjet exhaust expansion to produce sufficient thrust to propel the vehicle into altitudes and Mach regimes where scramjet operation can be initiated. This aspect includes a Computational Fluid Dynamics (CFD)-based geometric study to determine the optimal configuration to provide the best thrust values. The CFD parametric analysis investigated three candidate nozzles and indicated that the dual bell nozzle design produced the highest thrust values when compared to other nozzle geometries. The altitude adaptation study also validated the effectiveness of the nozzle thrust at various altitudes without compromising its thrust-producing capabilities. Computational data were validated against published experimental data, which indicated that the computed values correlated well with the experimental data. [ABSTRACT FROM AUTHOR]

The effect of thermal and chemical boundary conditions on the structure and chemical composition of the wake behind a 3D Mach 7 sphere-cone at an angle of attack of 5 degrees and an altitude of roughly 30,000 m is explored. A special emphasis is placed on determining the number density of chemical species which might lead to detection via the electromagnetic spectrum. The use of non-ablating cold-wall, adiabatic, and radiative equilibrium wall boundary conditions are used to simulate extremes in potential thermal protection system designs. Non-ablating, as well as an ablating boundary condition using the "steady-state ablation" assumption to compute a surface energy balance on the wall are used in order to determine the impacts of ablation on wake composition. On-body thermal boundary conditions downstream of an ablating nose are found to significantly affect wake temperature and composition, while the role of catalysis is found to change the composition only marginally except at very high temperatures on the cone's surface for the flow regime considered. Ablation is found to drive the extensive production of detectable species otherwise unrelated to ablation, whereas if ablation is not present at all, air-species which would otherwise produce detectable spectra are minimal. Studies of afterbody cooling techniques, as well as shape, are recommended for further analysis. [ABSTRACT FROM AUTHOR]

Through Computational Fluid Dynamics and validation, an optimal scramjet combustor has been designed based on twin-strut Hydrogen injection to sustain flight at a desired speed of Mach 8. An investigation undertaken into the efficacy of supersonic combustion through various means of injection saw promising results for Hydrogen-based systems, whereby strut-style injectors were selected over transverse injectors based on their pressure recovery performance and combustive efficiency. The final configuration of twin-strut injectors provided robust combustion and a stable region of net thrust (1873 kN) in the nozzle. Using fixed combustor inlet parameters and injection equivalence ratio, the finalized injection method advanced to the early stages of two-dimensional (2-D) and three-dimensional (3-D) scramjet engine integration. The overall investigation provided a feasible supersonic combustion system, such that Mach 8 sustained cruise could be achieved by the aircraft concept in a computational design domain. [ABSTRACT FROM AUTHOR]

The goal of this study is to assess CFD capability for the prediction of shock wave laminar boundary layer interactions at hypersonic velocities. More specifically, the flow field over a double-cone configuration is simulated using both perfect gas and non-equilibrium Navier-Stokes models. Computations are compared with recent experimental data obtained from measurements conducted in the LENS XX (Large Energy National Shock Expansion Tunnel Version 2) at the Calspan University of Buffalo Research Center (CUBRC). Four separate cases of freestream conditions are simulated to examine the models for a range of stagnation enthalpies from 5.44 MJ/kg to 21.77 MJ/kg and Mach numbers from 10.9 to 12.82. [ABSTRACT FROM AUTHOR]

Scramjets have become a main focus of study for many researchers, due to their application as propulsive devices in hypersonic flight. This entails a detailed understanding of the fluid mechanics involved to be able to design and operate these engines with maximum efficiency even at their off-design conditions. It is the objective of the present cold-flow investigation to study and analyse experimentally the mechanics of the fluid structures encountered within a generic scramjet inlet at M = 5. Traditionally, researchers have to rely on stream-thrust analysis, which requires the complex setup of a mass flow meter, a force balance and a heat transducer in order to measure inlet-isolator performance. Alternatively, the pitot rake could be positioned at inlet-isolator exit plane, but this method is intrusive to the flow, and the number of pitot tubes is limited by the model size constraint. Thus, this urgent need for a better flow diagnostics method is addressed in this paper. Pressure-sensitive paint (PSP) has been applied to investigate the flow characteristics on the compression ramp, isolator surface and isolator sidewall. Numerous shock-shock interactions, corner and shoulder separation regions, as well as shock trains were captured by the luminescent system. The performance of the scramjet inlet-isolator has been shown to improve when operated in a modest angle of attack. [ABSTRACT FROM AUTHOR]

Shock/boundary layer interaction (SBLI) is an undesirable phenomenon, occurring in high-speed propulsion systems. The conventional method to manipulate and control SBLI is using a bleed system that involves the removal of a certain amount of mass of the inlet flow to control boundary layer separation. However, the system requires a larger nacelle to compensate the mass loss, larger nacelles contribute to additional weight and drag and reduce the overall performance. This study investigates a novel type of flow control device called micro-ramps, a part of the micro vortex generators (VGs) family that intends to replace the bleed technique. Micro-ramps produce pairs of counter-rotating streamwise vortices, which help to suppress SBLI and reduce the chances of flow separation. Experiments were done at Mach 5 with two micro-ramp models of different sizes. Schlieren photography, surface flow visualization and infrared thermography were used in this investigation. The results revealed the detailed flow characteristics of the micro-ramp, such as the primary and secondary vortices. This helps us to understand the overall flow physics of micro-ramps in hypersonic flow and their application for SBLI control. [ABSTRACT FROM AUTHOR]

This study investigated a pre-cooled turbojet engine for a Mach 5 class hypersonic transport aircraft. The engine was demonstrated under takeoff and Mach 2 flight conditions, and a Mach 5 propulsion wind tunnel test is planned. The engine is composed of a pre-cooler, a core engine, and an afterburner. The engine was tested under simulated Mach 4 conditions using an air supply facility. High-temperature air under high pressure was supplied to the engine components through an airflow control valve and an orifice flow meter, and liquid hydrogen was supplied to the pre-cooler and the core engine. The results confirmed that the starting sequence of the engine components was effective under simulated Mach 4 conditions using liquid hydrogen fuel. The pre-cooling effect caused no damage to the rotating parts of the core engine in the experiment. [ABSTRACT FROM AUTHOR]

In the traditional investigations on the drag and heat reduction of hypersonic spiked models, only the aerodynamic calculation is performed, and the structural temperature cannot be obtained. This paper adopted the loosely coupled method to study its efficiency of drag and heat reduction, in which the feedback effect of wall temperature rise on aeroheating is considered. The aeroheating and structural temperature were obtained by the CFD and ABAQUS software respectively. The coupling analysis of the hypersonic circular tube was carried out to verify the accuracy of the fluid field, the structural temperature, and the coupled method. Compared with experimental results, the calculated results showed that the relative errors of stagnation heat flux and stagnation temperature were 1.34% and 4.95% respectively, and thus the effectiveness of the coupled method was verified. Installing a spike reduced the total drag of the forebody. The spiked model with an aerodisk reduced the aeroheating of the forebody, while the model without an aerodisk intensified the aeroheating. The spiked model with a planar aerodisk had the best performance on drag and heat reduction among all the models. In addition, increasing the length of the spike reduced the drag and temperature of the forebody. With the increase of the length, the change rates of drag, pressure, heat flux, and temperature decreased gradually. Increasing the diameter of the aerodisk also reduced the temperature of the forebody, while the efficiency of forebody drag reduction first increased and then decreased. In conclusion, the heat and drag reduction must be considered comprehensively for the optimal design of the spike. [ABSTRACT FROM AUTHOR]

The global surface pressure was measured on a 7 ° half-angle circular cone/flare model at a nominally zero angle of attack using pressure-sensitive paint (PSP). These experiments were conducted to illustrate fast PSP's usefulness and effectiveness at measuring the unsteady structures inherent to hypersonic shock-wave/boundary-layer interactions (SWBLIs). Mean and fluctuating surface pressure was measured with a temperature-corrected, high-frequency-response (≈10 kHz) anodized-aluminum pressure-sensitive paint (AA-PSP) allowing for novel, global calculations of skewness and coherence. These analyses complement traditional SWBLI data-reduction methodologies by providing high-spatial-resolution measurements of the mean and fluctuating locations of the shock feet, as well as the frequency-dependent measure of the relationship between characteristic flow features. The skewness indicated the mean locations of the separation and reattachment shock feet as well as their fluctuations over the course of the test. The coherence indicated that the separation and reattachment shock feet fluctuate about their mean location at the same frequency as one another, but 180 degrees out of phase. This results in a large-scale 'breathing motion' of the separated region characteristic of large separation bubbles. These experimental findings validate the usefulness of AA-PSP, and associated data-reduction methodologies, to provide global physical insights of unsteady SWBLI surface behavior in the hypersonic flow regime. Similar methodologies can be incorporated in future experiments to investigate complex and novel SWBLIs. [ABSTRACT FROM AUTHOR]

This report assesses the performance characteristics of a ramjet compression system in the application of a hypersonic vehicle. The vehicle is required to be self-powered and perform a complete flight profile using a combination of turbojet, ramjet and scramjet propulsion systems. The ramjet has been designed to operate between Mach 2.5 to Mach 5 conditions, allowing for start-up of the scramjet engine. Multiple designs, including varying ramp configurations and turbo-ramjet combinations, were investigated to evaluate their merits and limitations. Challenges arose with attempting to maintain sufficient pressure recoveries and favourable flow characteristics into the ramjet combustor. The results provide an engine inlet design capable of propelling the vehicle between the turbojet and scramjet phase of flight, allowing for the completion of its mission profile. Compromises in the design, however, had to be made in order to allow for optimisation of other propulsion systems including the scramjet nozzle and aerodynamics of the vehicle; it was concluded that these compromises were justified as the vehicle uses the ramjet engine for a minority of the flight profile as it transitions between low supersonic to hypersonic conditions. [ABSTRACT FROM AUTHOR]

In this paper, we propose a robust adaptive cubature Kalman filter (CKF) to deal with the problem of an inaccurately known system model and noise statistics. In order to overcome the kinematic model error, we introduce an adaptive factor to adjust the covariance matrix of state prediction, and process the influence introduced by dynamic disturbance error. Aiming at overcoming the abnormality error, we propose the robust estimation theory to adjust the CKF algorithm online. The proposed adaptive CKF can detect the degree of gross error and subsequently process it, so the influence produced by the abnormality error can be solved. The paper also studies a typical application system for the proposed method, which is the ultra-tightly coupled navigation system of a hypersonic vehicle. Highly dynamical scene experimental results show that the proposed method can effectively process errors aroused by the abnormality data and inaccurate model, and has better tracking performance than UKF and CKF tracking methods. Simultaneously, the proposed method is superior to the tracing method based on a single-modulating loop in the tracking performance. Thus, the stable and high-precision tracking for GPS satellite signals are preferably achieved and the applicability of the system is promoted under the circumstance of high dynamics and weak signals. The effectiveness of the proposed method is verified by a highly dynamical scene experiment. [ABSTRACT FROM AUTHOR]

A high-order finite difference method was used to simulate the hypersonic flow field over a blunt cone with different height roughness elements. The unsteady flow field induced by pulse disturbances was analyzed and compared with that under continuous disturbances. The temporal and spatial evolution characteristics of disturbances in the boundary layer were investigated and the propagation of different disturbance modes in the boundary layer was researched through the fast Fourier transform (FFT) method. The effect of the roughness element on the receptivity characteristic of the hypersonic boundary layer under pulse entropy disturbances was explored. The results showed that the different mode disturbances near roughness in the boundary layer were enlarged in the upstream half of the roughness element and suppressed in the downstream half. However, the effect of roughness weakened gradually as the disturbance frequency increased in the boundary layer. A phenomenon of mode competition in the downstream region of the roughness element exited. As the disturbances propagated downstream, the fundamental mode gradually became the dominant mode. A certain promotion effect on the mode competition was induced by the roughness element and the effect was enhanced with the increase in the roughness element height. [ABSTRACT FROM AUTHOR]