Search

A metasurface array for electromagnetic (EM) energy harvesting for Wi-Fi bands is presented in this paper; the metasurface array consists of a metasurface unit, a rectifier, and a load resistor. Each row of unit cells in the array is interconnected to form an energy transfer channel, which enables the transfer and concentration of incident power. Furthermore, at the terminal of the channel, a single series diode rectifier circuit and a load resistor are integrated in a coplanar manner. It is used to rectify the energy in Wi-Fi bands and enables DC energy harvesting across the load. Finally, a 5 × 7 prototype of the metasurface array is fabricated and measured for the verification of the rationality of the design. Testing in an anechoic chamber shows that the prototype achieves a 72% RF-DC efficiency at 5.9 GHz when the available incident power is about 7 dBm. [ABSTRACT FROM AUTHOR]

This paper presents a waveguide Lens antenna at the W-band adopting dual-focusing Lens to improve the performance. The Lens antenna consisted of a waveguide slotted structure and lenses processed using NOA73 meet the demands of miniaturization for current communication systems. The antenna radome fabricated using NOA73 not only protects the antenna structure but also improves the gain of the antenna by about 9.5 dBi via electromagnetic wave dual-focusing. A prototype is fabricated using novel UV-LIGA technology. Measured results are compared with simulated values. Measured results confirmed the fabricated antenna operated in the W-band with a 10 dB fractional bandwidth (FBW) of 6.5% from 97.5 to 104 GHz and a peak gain of 22 dBi at 100 GHz in the direction perpendicular to the plane of the feed waveguide. A good agreement between simulation and measurement is obtained, demonstrating efficient radiations in the operating band. [ABSTRACT FROM AUTHOR]

A dual-band metasurface array is presented in this paper for electromagnetic (EM) energy harvesting in the Wi-Fi band and Ku band. The array consists of metasurface unit cells, rectifiers, and load resistors. The metasurface units within each column are interconnected to establish two channels of energy delivery, enabling the transmission and aggregation of incident power. At the terminals of two channels, a single series diode rectifier and a voltage doubler rectifier are integrated into them to rectify the energy in the Wi-Fi band and the Ku band, respectively. A 7 × 7 prototype of the metasurface array is fabricated and tested. The measured results in the anechoic chamber show that the RF-to-dc efficiencies of the prototype at 2.4 GHz and 12.6 GHz reach 64% and 55% accordingly, when the available incident power at the surface is 3 dBm and 14 dBm, respectively. [ABSTRACT FROM AUTHOR]

In the terahertz band, how integrating multiple functions into a device with a tiny unit structure is a challenge. In this paper, an optically-controlled multifunctional linear polarization conversion metasurface working in the terahertz band is proposed. The reflection and transmission polarization conversion functions can be realized by irradiating the metasurface with pump light with different wavelengths. The metasurface is designed with a multilayer structure, and a photosensitive semiconductor alone is used to control multiple functions, which makes the manipulation of multifunctional devices easy. When the photosensitive semiconductor germanium (Ge) and silicon (Si) are in different states, the metasurface can realize broadband reflection and transmission polarization conversion functions, the corresponding relative bandwidth are 102.4% and 98.9%, respectively, and the work efficiency can be regulated by pump light with different intensity and wavelength. In addition, the working principle of the metasurface is analyzed by eigenmode theory and surface current distributions. The stability of the metasurface to structural parameters and incident angles are discussed. [ABSTRACT FROM AUTHOR]

The precise control of target particles (20 µm) at different inclination angles θi is achieved by combining a perturbed asymmetric sheathless Y-type microchannel and a digital transducer (IDT). The offset single-row micropillar array with the buffer area can not only concentrate large and small particles in a fixed region of the flow channel, but also avoid the large deflection of some small particles at the end of the array. The addition of the buffer area can effectively improve the separation purity of the chip. By exploring the manufacturing process of the microchannel substrate, an adjustable tilted-angle scheme is proposed. The use of ataTSAW makes the acoustic field area in the microchannel have no corner effect region. Through experiments, when the signal source frequency was 33.6 MHz, and the flow rate was 20 µL/min, our designed chip could capture 20 µm particles when θi = 5°. The deflection of 20 µm particles can be realized when θi = 15°–45°. The precise dynamic separation of 20 µm particles can be achieved when θi = 25°–45°, and the separation purity and efficiency were 97% and 100%, respectively. [ABSTRACT FROM AUTHOR]

The combination of the new perturbed spiral channel and a slanted gold interfingered transducer (IDT) is designed to achieve precise dynamic separation of target particles (20 μm). The offset micropillar array solves the defect that the high-width flow (avoiding the occurrence of channel blockage) channel cannot realize the focusing of small particles (5 μm, 10 μm). The relationship between the maximum design gap of the micropillar (Smax) and the particle radius (a) is given: Smax = 4a, which not only ensures that small particles will not pass through the micropillar gap, but also is compatible with the appropriate flow rates. A non-offset micropillar array was used to remove 20 μm particles in the corner area. The innovation of a spiral channel structure greatly improves the separation efficiency and purity of the separation chip. The separation chip designed by us achieves deflection separation of 20 μm particles at 24.95–41.58 MHz (κ = 1.09–1.81), at a flow rate of 1.2 mL per hour. When f = 33.7 MHz (κ = 1.47), the transverse migration distance of 20 μm particles is the smallest, and the separation purity and efficiency are as high as 92% and 100%, respectively. [ABSTRACT FROM AUTHOR]

In order to better detect information about a mass in breast tissue, an ultrasound tomography algorithm based on adaptive time gain compensation (TGC) was designed. Field II was utilized to automatically evaluate the phantom attenuation coefficient and compensate for the attenuated image. The image reconstruction algorithm process is presented here. Furthermore, the experimental setup with the cylindrical motion of a piezoelectric micromachined ultrasonic transducer (PMUT) linear array was used to detect the mass in the breast model. The attenuation coefficient was evaluated by using the spectral cross-correlation method. According to the acquired attenuation coefficients, TGC compensates for the pulse-echo signal, and the horizontal slice image was reconstructed using the tomography algorithm. The experimental results show that this algorithm can evaluate the attenuation coefficient of the breast model and improve the ability to detect an internal mass. At the same time, the realization of attenuation compensation with software is beneficial to the development of portable medical equipment. [ABSTRACT FROM AUTHOR]

In this paper, we propose a multi-perspective ultrasound imaging technology with the cylindrical motion of four piezoelectric micromachined ultrasonic transducer (PMUT) rotatable linear arrays. The transducer is configured in a cross shape vertically on the circle with the length of the arrays parallel to the z axis, roughly perpendicular to the chest wall. The transducers surrounded the breast, which achieves non-invasive detection. The electric rotary table drives the PMUT to perform cylindrical scanning. A breast model with a 2 cm mass in the center and six 1-cm superficial masses were used for the experimental analysis. The detection was carried out in a water tank and the working temperature was constant at 32 °C. The breast volume data were acquired by rotating the probe 90° with a 2° interval, which were 256 × 180 A-scan lines. The optimized segmented dynamic focusing technology was used to improve the image quality and data reconstruction was performed. A total of 256 A-scan lines at a constant angle were recombined and 180 A-scan lines were recombined according to the nth element as a dataset, respectively. Combined with ultrasound imaging algorithms, multi-perspective ultrasound imaging was realized including vertical slices, horizontal slices and 3D imaging. The seven masses were detected and the absolute error of the size was approximately 1 mm where even the image of the injection pinhole could be seen. Furthermore, the breast boundary could be seen clearly from the chest wall to the nipple, so the location of the masses was easier to confirm. Therefore, the validity and feasibility of the data reconstruction method and imaging algorithm were verified. It will be beneficial for doctors to be able to comprehensively observe the pathological tissue. [ABSTRACT FROM AUTHOR]

Capacitive micromachined ultrasound transducers (CMUTs) have broad application prospects in medical imaging, flow monitoring, and nondestructive testing. CMUT arrays are limited by their fabrication process, which seriously restricts their further development and application. In this paper, a vacuum-sealed device for medical applications is introduced, which has the advantages of simple manufacturing process, no static friction, repeatability, and high reliability. The CMUT array suitable for medical imaging frequency band was fabricated by a silicon wafer bonding technology, and the adjacent array devices were isolated by an isolation slot, which was cut through the silicon film. The CMUT device fabricated following this process is a 4 × 16 array with a single element size of 1 mm × 1 mm. Device performance tests were conducted, where the center frequency of the transducer was 3.8 MHz, and the 6 dB fractional bandwidth was 110%. The static capacitance (29.4 pF) and center frequency (3.78 MHz) of each element of the array were tested, and the results revealed that the array has good consistency. Moreover, the transmitting and receiving performance of the transducer was evaluated by acoustic tests, and the receiving sensitivity was −211 dB @ 3 MHz, −213 dB @ 4 MHz. Finally, reflection imaging was performed using the array, which provides certain technical support for the research of two-dimensional CMUT arrays in the field of 3D ultrasound imaging. [ABSTRACT FROM AUTHOR]

Cell separation has become @important in biological and medical applications. Dielectrophoresis (DEP) is widely used due to the advantages it offers, such as the lack of a requirement for biological markers and the fact that it involves no damage to cells or particles. This study aimed to report a novel approach combining 3D sidewall electrodes and contraction/expansion (CEA) structures to separate three kinds of particles with different sizes or dielectric properties continuously. The separation was achieved through the interaction between electrophoretic forces and inertia forces. The CEA channel was capable of sorting particles with different sizes due to inertial forces, and also enhanced the nonuniformity of the electric field. The 3D electrodes generated a non-uniform electric field at the same height as the channels, which increased the action range of the DEP force. Finite element simulations using the commercial software, COMSOL Multiphysics 5.4, were performed to determine the flow field distributions, electric field distributions, and particle trajectories. The separation experiments were assessed by separating 4 µm polystyrene (PS) particles from 20 µm PS particles at different flow rates by experiencing positive and negative DEP. Subsequently, the sorting performances of the 4 µm PS particles, 20 µm PS particles, and 4 µm silica particles with different solution conductivities were observed. Both the numerical simulations and the practical particle separation displayed high separating efficiency (separation of 4 µm PS particles, 94.2%; separation of 20 µm PS particles, 92.1%; separation of 4 µm Silica particles, 95.3%). The proposed approach is expected to open a new approach to cell sorting and separating. [ABSTRACT FROM AUTHOR]

Although wearable antennas have made great progress in recent years, how to design high-performance antennas suitable for most wireless communication systems has always been the direction of RF workers. In this paper, a new approach for the design and manufacture of a compact, low-profile, broadband, omni-directional and conformal antenna is presented, including the use of a customized flexible dielectric substrate with high permittivity and low loss tangent to realize the compact sensing antenna. Poly-di-methyl-siloxane (PDMS) is doped a certain proportion of aluminum trioxide (Al2O3) and Poly-tetra-fluoro-ethylene (PTFE) to investigate the effect of dielectric constant and loss tangent. Through a large number of comparative experiments, data on different doping ratios show that the new doped materials are flexible enough to increase dielectric constant, reduce loss tangent and significantly improve the load resistance capacity. The antenna is configured with a multisection microstrip stepped impedance resonator structure (SIR) to expand the bandwidth. The measured reflection return loss (S11) showed an operating frequency band from 0.99 to 9.41 GHz, with a band ratio of 146%. The antenna covers two important frequency bands, 1.71–2.484 GHz (personal communication system and wireless body area network (WBAN) systems) and 5.15–5.825 GHz (wireless local area network-WLAN)]. It also passed the SAR test for human safety. Therefore, the proposed antenna offers a good chance for full coverage of WLAN and large-scale development of wearable products. It also has potential applications in communication systems, wireless energy acquisition systems and other wireless systems. [ABSTRACT FROM AUTHOR]

The advantages of the capacitive micromachined ultrasound transducer (CMUT) technology have provided revolutionary advances in ultrasound imaging. Extensive research on CMUT devices for high-frequency medical imaging applications has been conducted because of strong demands and fabrication realization by using standard silicon IC fabrication technology. However, CMUT devices for low-frequency underwater imaging applications have been rarely researched because it is difficult to fabricate thick membrane structures through depositing processes using standard IC fabrication technology due to stress-related problems. To address this shortcoming, in this paper, a CMUT device with a 2.83-μm thick silicon membrane is proposed and fabricated. The CMUT device is fabricated using silicon fusion wafer-bonding technology. A 5-μm thick Parylene-C is conformally deposited on the device for immersion measurement. The results show that the fabricated CMUT can transmit an ultrasound wave, receive an ultrasound wave, and have pulse-echo measurement capability. The ability of the device to emit and receive ultrasonic waves increases with the bias voltage but does not depend on the voltage polarity. The results demonstrate the viability of the fabricated CMUT in low-frequency applications from the perspectives of the device structure, fabrication, and characterization. This study presents the potential of the CMUT for underwater ultrasound imaging applications. [ABSTRACT FROM AUTHOR]

Sensor technology is one of the three pillars of information technology. This paper aims to discuss the problems of insensitive detection, poor stability, and uncomfortable wearing of sensors in the fields of human–computer interaction, 5G communication, and medical detection. A sensing unit with a microstructured flexible sensing front end is a cone-like structure with a single size of 18–22 μm. They are evenly distributed and can reach 2500 units per square millimeter. In the pressure range, the sensitivity of the sensor unit is 0.6 KPa−1 (no microstructure sensitivity at 0.15 KPa−1), and the response time is fast (<600 ms). After 400 repeated stretching experiments, the sensor unit can still maintain a stable output signal. Due to its flexible characteristics (50% tensile conductivity), the sensor unit can act on human skin and other curved surfaces. According to the prepared sensing unit, good test results can be obtained on the testing of mechanical devices, curved surfaces of human bodies, and non-contact methods. It is observed that the flexible sensor can be applied to various test occasions, and the manufacturing process of the sensing unit will provide new ideas and methods for the preparation of the flexible sensor technology. [ABSTRACT FROM AUTHOR]

Currently, breast cancer is one of the most common cancers in women all over the world. A novel 3D breast ultrasound imaging ring system using the linear array transducer is proposed to decrease costs, reduce processing difficulties, and improve patient comfort as compared to modern day breast screening systems. The 1 × 128 Piezoelectric Micromachined Ultrasonic Transducer (PMUT) linear array is placed 90 degrees cross-vertically. The transducer surrounds the mammary gland, which allows for non-contact detection. Once the experimental platform is built, the breast model is placed through the electric rotary table opening and into a water tank that is at a constant temperature of 32 °C. The electric rotary table performs a 360° scan either automatically or mechanically. Pulse echo signals are captured through a circular scanning method at discrete angles. Subsequently, an ultrasonic tomography algorithm is designed, and a horizontal slice imaging is realized. The experimental results indicate that the preliminary detection of mass is realized by using this ring system. Circular scanning imaging is obtained by using a rotatable linear array instead of a cylindrical array, which allows the size and location of the mass to be recognized. The resolution of breast imaging is improved through the adjustment of the angle interval (>0.05°) and multiple slices are gained through different transducer array elements (1 × 128). These results validate the feasibility of the system design as well as the algorithm, and encourage us to implement our concept with a clinical study in the future. [ABSTRACT FROM AUTHOR]