Search

In the present investigation, aluminum metal matrix composites (AMMs) reinforced with aluminum nitride (AlN) nanoparticulates at different volumetric ratios of (0, 0.5, 1, 1.5, and 2 vol.%) were manufactured via a microwave-assisted powder metallurgy technique. The morphological, physical, mechanical, and electrochemical properties of the produced billets were examined to reflect the impact of the successive addition of AlN into the aluminum (Al) matrix. The morphological analysis revealed the high crystalline patterns of the formation of the Al-AlN composites. The microstructural analysis confirmed the presence of the elemental constituents of Al and AlN particles in the fabricated composites, showing an enhanced degree of agglomeration in conjunction with the additional amount of AlN. Positive behavior exhibited by the micro- and nanohardness was noticeable in the Al-AlN composites, especially at the ultimate concentration of AlN in the Al matrix of a 2 vol.%, where it reached 669.4 ± 28.1 MPa and 659.1 ± 11 MPa compared to the pure Al metal at 441.2 ± 20 MPa and 437.5 ± 11 MPa, respectively. A declining trend in the compressive strength was recorded in the reinforced Al samples. The corrosion resistance of the AlN-reinforced Al metal matrix was estimated at 3.5 wt.% NaCl using electrochemical impedance spectroscopy and potentiodynamic polarization. The results reveal that the inclusion of 2.0 vol.%AlN led to the lowest corrosion rate. [ABSTRACT FROM AUTHOR]

This study investigates the simultaneous decoration of vertically aligned molybdenum disulfide nanostructure (VA-MoS2) with Ag nanoparticles (NPs) and nitrogen functionalization. Nitrogen functionalization was achieved through physical vapor deposition (PVD) DC-magnetron sputtering using nitrogen as a reactive gas, aiming to induce p-type behavior in MoS2. The utilization of reactive sputtering resulted in the growth of three-dimensional silver structures on the surface of MoS2, promoting the formation of silver nanoparticles. A comprehensive characterization was conducted to assess surface modifications and analyze chemical and structural changes. X-ray photoelectron spectroscopy (XPS) showed the presence of silver on the MoS2 surface. Scanning electron microscopy (SEM) confirmed successful decoration with silver nanoparticles, showing that deposition time affects the size and distribution of the silver on the MoS2 surface. [ABSTRACT FROM AUTHOR]

Hot pressing represents a promising consolidation technique for ball-milled bismuth telluride alloys, yet deep investigations are needed to understand its effect on the thermoelectric properties. This paper studies the effect of hot-pressing parameters (temperature and pressure) on the thermoelectric properties of the n-type Gr-Bi2Te2.55Se0.45 nanocomposite. Ultra-high pressure, up to 1.5 GPa, is considered for the first time for consolidating Bi2(Te,Se)3 alloys. Results from this study show that increasing the temperature leads to changes in chemical composition and causes noticeable grain growth. On the contrary, increasing pressure mainly causes improvements in densification. Overall, increments in these two parameters improve the ZT values, with the temperature parameter having a higher influence. The highest ZT of 0.69 at 160 °C was obtained for the sample hot-pressed at 350 °C and 1 GPa for 5 min, which is indeed an excellent and competitive value when compared with results reported for this n-type Bi2Te2.55Se0.45 composition. [ABSTRACT FROM AUTHOR]

Heterobasidion spp. are among the most destructive root rot pathogens, causing severe economic losses to conifer forestry. High infection frequency has been observed in Scots pine stands growing on dry sandy soils with low organic matter or former agricultural soils. In this study, we investigated the incidence of Heterobasidion spp. infection in Scots pine forests established on low-risk sites where the trees looked healthy and unlikely to be infected. In total, 135 healthy-looking pine trees from nine different stands were examined for Heterobasidion spp. presence. Heterobasidion spp. was detected in six stands and infection frequency was 13%–33%. There was a significant correlation between site index and infection frequency, which was higher in pine stands established on more fertile soils. There was no correlation between disease incidence and defoliation level, diameter of tree at breast height, root diameter, tree volume, or stand age. Overall, our results showed that, regardless of the soil type, Scots pine can be intensively infected by Heterobasidion pathogens while showing no outward signs. Therefore, the risk of Heterobasidion disease should be taken into consideration in management of pine forests growing on both low- and high-risk sites for more productive and sustainable forests. [ABSTRACT FROM AUTHOR]

The oil and gas industry is involved with severe corrosive/sour environmental conditions due to H2S, CO2, and moisture content. The National Association of Corrosion Engineers (NACE) has developed standards to enable users to select suitable materials for given sour conditions which utilize laboratory testing. A failed piping sample (API-5L-X65) was removed from a pipeline after 15 years of service. Optical microscopy was used to compare the microstructure of the corroded sample near the exposed surface to both the service environment, and further away from it. Moreover, pitted samples were analyzed using a scanning electron microscope coupled with energy dispersive X-ray (SEM/EDS) to understand the deposits' morphology. Furthermore, XPS analysis proves the presence of a significant content of sulfur compound. Additionally, the mechanical properties of both corroded and non-corroded samples were evaluated and compared. Micro-hardness was carried out on the cross-section of the removed sample to understand any evident hardness variation from the inner diameter (ID) to the outer diameter (OD) of the piping. All the results suggest that prolonged service exposure has resulted in the development of micro defects, resulting in the reduction of strength and impact toughness, and the reduction in the hardness at the exposed surface of the corroded piping. Understanding the corrosion mechanism of pipelines exposed to sour media in the long-term helps in repair/replacement planning and extending the usable design life of the material, and paving the way for the oil and gas industry to develop additional ways to monitor the changes in the critical materials' properties when exposed to sour service. [ABSTRACT FROM AUTHOR]

This paper suggests an assistive system for the toilet with the objective of measuring human activities and to provide intelligent mechanical assistance to help seating and standing. The project intends to develop a seating assistance as a technical aid in order to reduce accidents and falls in the bathroom. The preferred technique is human-robot physical interaction algorithms known in collaborative robotics (cobot) and adapting it to a personalized assistance technology installed on a smart toilet. First, the design of the mechanical assistance is presented. Then, an admittance controller is designed and implemented in order to help the user in a similar way as a cobot could be used. This technique could be used to assist the user and improve balance with adequate training and an adequate configuration of the admittance controller. [ABSTRACT FROM AUTHOR]

In this paper, we report a novel microfluidic method to conduct a Caenorhabditis elegans electrotaxis movement assay and neuronal imaging on up to 16 worms in parallel. C. elegans is a model organism for neurodegenerative disease and movement disorders such as Parkinson's disease (PD), and for screening chemicals that alleviate protein aggregation, neuronal death, and movement impairment in PD. Electrotaxis of C. elegans in microfluidic channels has led to the development of neurobehavioral screening platforms, but enhancing the throughput of the electrotactic behavioral assay has remained a challenge. Our device consisted of a hierarchy of tree-like channels for worm loading into 16 parallel electrotaxis screening channels with equivalent electric fields. Tapered channels at the ends of electrotaxis channels were used for worm immobilization and fluorescent imaging of neurons. Parallel electrotaxis of worms was first validated against established single-worm electrotaxis phenotypes. Then, mutant screening was demonstrated using the NL5901 strain, carrying human α -synuclein in the muscle cells, by showing the associated electrotaxis defects in the average speed, body bend frequency (BBF), and electrotaxis time index (ETI). Moreover, chemical screening of a PD worm model was shown by exposing the BZ555 strain, expressing green fluorescence protein (GFP) in the dopaminergic neurons (DNs), to 6-hydroxydopamine neurotoxin. The neurotoxin-treated worms exhibited a reduction in electrotaxis swimming speed, BBF, ETI, and DNs fluorescence intensity. We envision our technique to be used widely in C. elegans-based movement disorder assays to accelerate behavioral and cellular phenotypic investigations. [ABSTRACT FROM AUTHOR]

The rapid development of technology has brought about a revolution in healthcare stimulating a wide range of smart and autonomous applications in homes, clinics, surgeries and hospitals. Smart healthcare opens the opportunity for a qualitative advance in the relations between healthcare providers and end-users for the provision of healthcare such as enabling doctors to diagnose remotely while optimizing the accuracy of the diagnosis and maximizing the benefits of treatment by enabling close patient monitoring. This paper presents a comprehensive review of non-invasive vital data acquisition and the Internet of Things in healthcare informatics and thus reports the challenges in healthcare informatics and suggests future work that would lead to solutions to address the open challenges in IoT and non-invasive vital data acquisition. In particular, the conducted review has revealed that there has been a daunting challenge in the development of multi-frequency vital IoT systems, and addressing this issue will help enable the vital IoT node to be reachable by the broker in multiple area ranges. Furthermore, the utilization of multi-camera systems has proven its high potential to increase the accuracy of vital data acquisition, but the implementation of such systems has not been fully developed with unfilled gaps to be bridged. Moreover, the application of deep learning to the real-time analysis of vital data on the node/edge side will enable optimal, instant offline decision making. Finally, the synergistic integration of reliable power management and energy harvesting systems into non-invasive data acquisition has been omitted so far, and the successful implementation of such systems will lead to a smart, robust, sustainable and self-powered healthcare system.