Search

In the area of the heating industry, a heat pump is an efficient alternative technology to achieve energy saving and carbon emission reduction. The conventional heat pump has gradually been applied to replace the traditional direct electrical heating method while the required temperature is below 100 °C. A heat pump with temperatures between 100–140 °C is in the stage of rapid development. However, a heat pump with temperatures above 150 °C has received relatively little attention. In this paper, two systems combining a heat pump and water vapor compression (CHPVC and HPTVC) have been studied for waste heat recovery from 45 °C to a water vapor supply with a temperature above 150 °C. A thermodynamic model has been proposed to analyze the performance of the two systems, and a twin-screw compressor model has been developed to calculate the isentropic efficiency of the compressor applied in the heat pump. Four different parameters have been used to analyze the energy efficiency. The simulation results show that while the inlet water temperature is 45 °C and the required vapor temperature is 150 °C, the optimal COPs of CHPVC and HPTVC are 2.432 and 2.436, respectively. Moreover, CHPVC is more suitable for the large saturation temperature lift, and HPTVC is more suitable for a relatively small temperature difference between the inlet water and the required vapor. Compared with the direct electrical heating method or the conventional two-stage heat pump, these two systems are remarkably efficient and show good energy-saving potential. [ABSTRACT FROM AUTHOR]

Micro-structured surfaces can affect heat transfer mechanisms because of enlarged specific surface areas. However, employing the Leidenfrost effect during liquid nitrogen (LN2) droplet cooling of a heated micro-structured surface possessing a fin with a spacing much smaller than the diameter of the droplet has not yet been explored. In the present work, a direct numerical simulation (DNS) is carried out to investigate heat transfer mechanisms of the LN2 droplet, whose diameter is sufficiently larger than the structured spacing of fin, impinging on a micro-structured surface with variable velocities. For a comparative study, a smooth surface is also employed in numerical simulations. The spreading mechanisms and vaporization behavior of the droplet along with liquid film morphology at various conditions are investigated. Results show that a smaller fin size inhibits LN2 in entering into the grooves between the fins and left the surface untouched by the droplet completely, and eventually, a thinner liquid film is spread out in contrast to the smooth surface. Notably, at a low Weber number, the droplet can be shrunk or even rebounded away from the wall after impinging on the wall. The fastest vaporization behavior for both surfaces, namely smooth and micro-structured, is obtained at a Weber number of 180. Additionally, an effective heat transfer upon the micro-structured surface is observed at a low impinging velocity of the droplet. [ABSTRACT FROM AUTHOR]

Magnetic refrigeration is acknowledged as a potential substitute for the conventional vapor-compression refrigeration technology, owing to its high efficiency and environmental friendliness. Existing magnetic refrigeration systems are mostly based on permanent magnets, owing to the characteristics of lower magnetic field intensity, non-uniform magnetic field distribution, and lower operating frequency due to the moving parts, which results in a low cooling capacity and small temperature difference. Thus, this study proposes the application of a pulsed magnetic field, with a high intensity and frequency, to a magnetic refrigeration system to achieve a high performance. A verified numerical model is established to investigate the thermodynamic cycle and cooling performance of an active magnetic regenerator (AMR). The transient and steady-state performances of AMR under pulsed and permanent magnetic fields are compared. The results suggest that an AMR can establish a stable temperature difference under a pulsed magnetic field that is 40 times faster than that under a permanent magnetic field. The maximum steady-state cooling capacity under a pulsed magnetic field is 2.5 times that under a permanent magnetic field when the temperature difference is 20 K. Additionally, the effects of pulsed magnetic field waveforms, frequency, and intensity on the performance of AMR are investigated under various utilization factors. These results can guide the improvement of room-temperature magnetic refrigerators. [ABSTRACT FROM AUTHOR]

In marine storage and transportation, the sloshing of liquid oxygen disturbs the thermodynamic equilibrium and induces stress on tank walls. Numerous problems are associated with the sloshing mechanism and demand a detailed investigation. In this study, a numerical model is developed by coupling the Eulerian framework and the algebraic interface area density (AIAD) method while considering the interphase drag force to investigate the thermal behavior of sloshing liquid oxygen. The effect of the sloshing frequency on the evaporation performance of liquid oxygen is studied. Moreover, anti-sloshing is conducted by employing a T-shaped baffle. The results show that the sloshing induced a vapor explosion phenomenon due to the invalidation of the surface impedance and thermal destratification to enhance free convection, resulting in rapid depressurization and increased evaporation loss. In addition, maximum evaporation loss occurred under the vapor–liquid coupling excitation condition. The T-shaped baffle has an excellent anti-sloshing effect because of the generating tip vortices and the enhanced shearing effect of the walls, which are regarded as motion damping factors. [ABSTRACT FROM AUTHOR]

Outer edge bending is already used on the axial fan blades of air conditioners, reducing the leakage flow loss at the blade tip and suppressing the tip vortex development, thereby improving fan aerodynamic and acoustic performance. However, there are few studies on the multi-parameter design and optimization of this complicated structure, and most studies only focus on the overall sound pressure level rather than the sound quality when evaluating the fan noise. This study investigated the effects of outer edge bending structure on the aerodynamic performance and sound quality of air conditioners' axial fans by experiments and numerical methods. Based on the orthogonal design method, the effects of three bending parameters, the circumferential starting angle, radial relative position, and the bending degree effects on the performance of the axial flow fan blade were analyzed, and the best efficiency scheme was selected. A comparative analysis of the preferred and the original bending schemes shows that the bending towards the blade suction surface successfully inhibits the development of tip leakage vortex at the blade tip, thereby achieving efficiency enhancement and noise reduction. The experimental results show that the preferred bending scheme with a 10° circumferential starting angle, 90% radial relative position, and 8% bending degree can effectively reduce the fan's broadband noise within 200~1000 Hz by 0.54~2.68 dB (A) at different operating conditions. Additionally, the preferred bending blade with reasonably designed bending effectively reduced the loudness and roughness of the fan noise in the rated conditions, and the sound quality of the studied fan was correspondingly improved. [ABSTRACT FROM AUTHOR]

In this study, a collaborative simulation method is proposed to predict dynamic variations of the thermal environment in an air-conditioned room. The room thermal environment was predicted and analyzed by varying the structural and control parameters of the air conditioner considering the dynamic coupling effect. Connections and regularities were established between the applicable parameters and evaluation indices of the thermal environment. The simulation results demonstrated the interactions among the system structural parameters, control parameters, and the thermal environment. Within a certain parameter range, the evaporator structure exhibited a significant effect on temperature uniformity and vertical air temperature difference, followed by predicted mean vote (PMV) and draught rate (DR). The associated evaluation indices were sensitive to fin spacing, tube spacing, and tube outer diameter, in the same order, which were structural parameters of the evaporator. The effect of the air supply angle on the vertical air temperature difference was evident; however, its influence on the PMV, DR, and temperature uniformity did not indicate consistent variations. [ABSTRACT FROM AUTHOR]