Search

The high-temperature superplastic deformation behavior of rolled Mg-8Al-2Sn (AT82) and Mg-8Al-1Sn-1Zn (ATZ811) alloys were investigated in this study. During tensile deformation at 573 K, no obvious grain growth occurred in both alloys, because of the high-volume fraction of second phases located at grain boundaries. Meanwhile, texture weakening was observed, suggesting that grain boundary sliding (GBS) is the dominant superplastic deformation mechanism, which agreed well with the strain rate sensitivity (m) and the activation energy (Q) calculations. The microstructural evolution during tensile deformation manifested that there were more and larger cavities in AT82 than ATZ811 during high-temperature tensile deformation. Therefore, superior superplasticity was found in the ATZ811 alloy that presented a tensile elongation of ~510% under a strain rate of 10−3 s−1 at 573 K, in contrast to the relatively inferior elongation of ~380% for the AT82 alloy. Meanwhile, good tensile properties at ambient temperature were also obtained in ATZ811 alloy, showing the ultimate tensile strength (UTS) of ~355 MPa, yield strength (YS) of ~250 MPa and elongation of ~18%. Excellent mechanical performance at both ambient and elevated temperatures can be realized by using economical elements and conventional rolling process, which is desirable for the industrial application of Mg alloy sheets. [ABSTRACT FROM AUTHOR]

The microstructure, mechanical properties and corrosion behavior of hot–rolled Mg–xSn–1Zn–0.5Ca (x = 1, 3 and 5 wt.%) alloys were investigated for possible application as biodegradable implants. The hot–rolled Mg–xSn–1Zn–0.5Ca alloys consisted of α-Mg matrix and Mg2Sn phase. The number of the Mg2Sn particles significantly increased and the grains were gradually refined (14.2 ± 1.5, ~10.7 ± 0.7 and ~6.6 ± 1.1 μm), while the recrystallized fraction significantly decreased with the increase in the Sn content, the Mg–1Sn–1Zn–0.5Ca alloy was almost completely recrystallized. Ultimate tensile strength (UTS) and tensile yield strength (TYS) increased slightly, reaching maximum values of 247 MPa and 116 MPa, respectively, for the Mg–5Sn–1Zn–0.5Ca alloy, and the elongation decreased with the increase in the Sn content; the Mg–1Sn–1Zn–0.5Ca alloy showed the highest elongation (15.3%). In addition, immersion tests and electrochemical measurements in Hank's solution revealed that the corrosion rates of Mg–xSn–1Zn–0.5Ca alloys increased with the increase in the Sn content. A model of the corrosion behavior was discussed for hot–rolled Mg–xSn–1Zn–0.5Ca alloys in Hank's solution. Among the Mg–xSn–1Zn–0.5Ca (x = 1, 3 and 5 wt.%) alloys, Mg–1Sn–1Zn–0.5Ca alloy exhibits optimal corrosion resistance and appropriate mechanical properties. [ABSTRACT FROM AUTHOR]

A high extrusion ratio of 166:1 was applied to commercial AZ61 alloy in one step with an extrusion speed of 2.1 m·min−1. The effects of DA (direct aging) treatment on the microstructure and tensile properties of extruded alloy were investigated. The extruded alloy exhibits fine DRXed grains and the average grain size is ~11 μm. After DA treatment at 170 °C, the tensile strength and 0.2% offset yield strength is enhanced from 314 to 336 MPa and from 169 to 191 MPa respectively, sacrificing elongation from 26.5% to 23.3%. The grain size and texture distribution of extruded AZ61 scarcely evolve during the post aging treatment. However, the enhanced strength in peak-aged alloy is mainly caused by the high-density elliptical Mg17Al12 precipitates distributing uniformly along the grain boundaries or within the grains, by precipitation and dispersion hardening. Furthermore, the nano-sized precipitates effectively inhibit grains from coarsening by triggering pinning effects along the grain boundaries at elevated temperature. As a result, the peak-aged alloy exhibits a better superplasticity of 306.5% compared with that of 231.8% of extruded sample. This work provides a practical one-step method for mass-producing Mg alloy sheets with excellent tensile strength and ductility compared with those fabricated by conventional extrusion methods. [ABSTRACT FROM AUTHOR]

The microstructure, mechanical properties and corrosion behavior of hot⁻rolled Mg⁻xSn⁻1Zn⁻0.5Ca (x = 1, 3 and 5 wt.%) alloys were investigated for possible application as biodegradable implants. The hot⁻rolled Mg⁻xSn⁻1Zn⁻0.5Ca alloys consisted of α-Mg matrix and Mg₂Sn phase. The number of the Mg₂Sn particles significantly increased and the grains were gradually refined (14.2 ± 1.5, ~10.7 ± 0.7 and ~6.6 ± 1.1 μm), while the recrystallized fraction significantly decreased with the increase in the Sn content, the Mg⁻1Sn⁻1Zn⁻0.5Ca alloy was almost completely recrystallized. Ultimate tensile strength (UTS) and tensile yield strength (TYS) increased slightly, reaching maximum values of 247 MPa and 116 MPa, respectively, for the Mg⁻5Sn⁻1Zn⁻0.5Ca alloy, and the elongation decreased with the increase in the Sn content; the Mg⁻1Sn⁻1Zn⁻0.5Ca alloy showed the highest elongation (15.3%). In addition, immersion tests and electrochemical measurements in Hank's solution revealed that the corrosion rates of Mg⁻xSn⁻1Zn⁻0.5Ca alloys increased with the increase in the Sn content. A model of the corrosion behavior was discussed for hot⁻rolled Mg⁻xSn⁻1Zn⁻0.5Ca alloys in Hank's solution. Among the Mg⁻xSn⁻1Zn⁻0.5Ca (x = 1, 3 and 5 wt.%) alloys, Mg⁻1Sn⁻1Zn⁻0.5Ca alloy exhibits optimal corrosion resistance and appropriate mechanical properties.

Nano-SiC particulates (n-SiC p ) reinforced Mg-8Al-1Sn (AT81) composites with different pre-oxidation parameters were fabricated by powder metallurgy (P/M) process combined with hot extrusion. The effects of pre-oxidization treatment of n-SiC p on the microstructure and tensile properties of 0.5 vol % n-SiC p /AT81 composites were investigated accordingly. The distribution of n-SiC p with different pre-oxidation parameters was homogeneous in the composites. Moreover, it was found that a thin MgAl₂O₄ layer formed at the interface when the n-SiC p were pre-oxidized at 1073 K for 2 h, while the MgAl₂O₄ layer became much thicker with pre-oxidization temperature increasing to 1273 K for 2 h. After an appropriate pre-oxidization treatment of n-SiC p at 1073 K for 2 h, the as-extruded 0.5 vol % n-SiC p /AT81 composites exhibited an enhanced strength. It was found that the yield strength (YS) and ultimate tensile strength (UTS) increased from 168 MPa and 311 MPa to 255 MPa and 393 MPa compared with the as-extruded AT81 alloy, reflecting 51.8% and 26.4% increments, respectively. The improvement of mechanical properties should be mainly attributed to the grain refinement and homogeneous distribution of n-SiC p in the composites. Moreover, a well-bonded interface and the formation of an appropriate amount of interfacial product (MgAl₂O₄) benefited the material's mechanical properties.

Twin-roll casting AZ31 Mg alloy sheets have been fabricated by normal unidirectional-rolling, head-to-tail rolling, and clock-rolling, respectively. It has been demonstrated that head-to-tail rolling is the most effective to refine the microstructure and weaken the basal texture among the three rolling routes. Excellent integrated tensile properties can be obtained by the head-to-tail rolling. The yield strength, ultimate tensile strength, and plastic elongation are 196 MPa, 301 MPa, and 28.9%, respectively. The strength can benefit from the fine grains (average value of 4.0 μm) of the AZ31 alloy processed by the head-to-tail rolling route, while the excellent plastic elongation is achieved owing to the weakened basal texture besides the fine grains. Results obtained here can be used as a basis for further study of some simple rolling methods, which is critical to the development of Mg alloys with high strength and plasticity.

It is found that Li₂Sb compound can act as the nucleus of primary Mg₂Si during solidification, by which the particle size of primary Mg₂Si decreased from ~300 to ~15-25 μm. Owing to the synergistic effect of the Li₂Sb nucleus and adsorption-poisoning of Li atoms, the effect of complex modification of Li-Sb on primary Mg₂Si was better than that of single modification of Li or Sb. When Li-Sb content increased from 0 to 0.2 and further to 0.5 wt.%, coarse dendrite changed to defective truncated octahedron and finally to perfect truncated octahedral shape. With the addition of Li and Sb, ultimate compression strength (UCS) of Al-20Mg₂Si alloys increased from ~283 to ~341 MPa and the yield strength (YS) at 0.2% offset increased from ~112 to ~179 MPa while almost no change was seen in the uniform elongation. Our study offers a simple method to control the morphology and size of primary Mg₂Si, which will inspire developing new Al-Mg-Si alloys with improved mechanical properties.

Damage to carbon nanotubes (CNTs) during the fabrication process of CNT reinforced composites has great influence on their mechanical properties. In this study, the 2014 Al with powder sizes of 20, 9 and 5 μm was selected to study the effect of initial particle size on the damage to carbon nanotubes (CNTs) during ball milling. The result shows that for CNTs in the ball milled CNT/Al (with powder size of 20 and 9 μm) mixtures, the intensity ratio of the D band and the G band (ID/IG) first increased and then reached a plateau, mainly because most of the CNTs are embedded, to a certain extent, in the aluminum powder after milling, which could protect the CNTs from damage during further milling. While for CNTs in the ball milled CNT/Al (with powder size of 5 μm) mixture, the ID/IG ratio continues to climb from 1.31 to 2.33 with time, indicating continuous damage to the CNTs occurs during the milling. Differential scanning calorimetry (DSC) analysis demonstrates that the chemical instability increased with an increase in the damage level of CNTs, resulting in the formation of aluminum carbide (Al₄C₃) at a lower temperature before the melting of aluminum, which is detrimental to their mechanical properties.