Search

Spiral grains are one of the most important tree growth defects that can remarkably affect the shape stability of lumber. This growth defect is observed by an oblique arrangement of axially oriented cell elements in the wood. This research focused on identifying and measuring selected shape changes caused by the spiral grains in the log. Hornbeam logs with spiral grain and with no spiral grain aged 60 and 52 years were selected to detect shape changes. Following the research and the norms of STN EN 1309-3 (49 1013), DIN (4074-5), and ASTM D245, it can be stated that spiral grain is an essential factor affecting the shape stability of hornbeam lumber. In the case of lumber with spiral grain, the spiral grain increased by up to 8° within three months. The warp of both types (bow, crook) increased exponentially throughout the study, peaking between the third and fourth week with an increase in warp bow of 26 mm and 17 mm in warp crook. [ABSTRACT FROM AUTHOR]

The cost of raw materials has a major role in the wood industry. From this point of view, it is necessary to pay attention to the correct log-sawing pattern, which will optimize the sawing process and increase the quantity and quality of the material as well. For measurements, we used beech wood (Fagus sylvatica L.). Beech wood (Fagus sylvatica L.) is the most common wood species in the Slovak Republic; the total amount in forests is 34.8%. Beech wood has a high frequency of defects, such as red false heartwood, reaction wood (i.e., tension wood), dote, cracks, and so on. This research aimed to analyze the effect of the log-sawing patterns of through-and-through sawing, cant sawing, and quarter sawing on the resulting quantitative–qualitative yields of beech timber. The results showed that the highest quantitative yield was observed with the cant sawing pattern, at 84%, which was, on average, 17.3% higher compared to other types of cutting. It was found that quarter sawing resulted in a higher qualitative yield compared to through-and-through sawing or cant sawing (V5 = 62.69% and V6 = 47.86%). [ABSTRACT FROM AUTHOR]

The mechanical properties of wood have remarkable influence on its use in buildings. The improvement of the mechanical properties enables the reduction in the cross-sections of structural elements, particularly the increase in their load. The paper deals with the change in the mechanical properties of beech wood through the process of contact drying. Plate pressures of 1.0, 1.4, and 1.6 MPa at a temperature of 160 °C were used. It was found that contact drying increased the bending strength by more than 30% compared to convection drying. The value of Brinell's hardness measured on the surface of the samples increased by 80 to 98% after contact drying, and the measured values of impact toughness were higher, about 31.1% compared to the samples dried by the convection drying method. As a result of contact drying, the density in the absolutely dry state increased for radial samples by 102.3 kg·m−3 and for tangential samples by 83.1 kg·m−3. The pressure of the plates also had an effect on the change in density. [ABSTRACT FROM AUTHOR]

The bark as a product of the dividing of wood and cork cambium consists of a set of protective layers of cells, which protect the living tissue (cambium) from the external environment and separate the bark from the wood. The structure of bark as a component of a living tree is completely different from wood. This article describes the testing of the adhesion of wood/bark in the longitudinal and tangential anatomical direction during the dormant and growing season on three choice wood species (oak, beech, and spruce). The results show a remarkable influence of the wood species and anatomical direction, as well as period of vegetation (dormant or growing season). All wood species had higher values of shear strength in the longitudinal direction compared to the tangential direction. The highest average values in the longitudinal direction were measured in the dormant period for sessile oak (0.49 MPa) and beech (0.48 MPa). The lowest value of shear strength in the longitudinal direction was measured for spruce (0.36 MPa). During the growing season, the highest average shear strength values were also measured in the longitudinal direction at beech (0.46 MPa) and oak (0.39 MPa). The lowest value of shear strength in the longitudinal direction was measured similarly for spruce (0.26 MPa). [ABSTRACT FROM AUTHOR]

The thermal treatment of wood changes its structure due to the degradation of wood polymers (cellulose, hemicellulose and lignin), so the physical properties of wood are either improved or degraded. Color changes apply not only to natural wood, but also to such wood composites for which some amount of glue is used in their construction (e.g., plywood, blockboard or laminboard). This article is focused on the analysis of hornbeam and field maple wood color changes influenced by drying temperature. Two types of drying modes were used: hot-air mode where the temperature of the drying environment was 60 °C, and high-temperature mode with a drying temperature of 120 °C. The drying mode was divided into two phases depending on the moisture content of the wood. The compared woods had similar values of color coordinates at the beginning of drying. During hot-air drying, the largest changes in color coordinates occurred during the first 24 h. The total color difference between the color at the end and the beginning of drying was 7.3 for hornbeam and 11.1 for maple. The overall color difference between the compared woods was minimal. During high-temperature drying (120 °C), the color changes of the dried woods were more pronounced. In the case of maple wood, there was a very significant change in color and the value of ΔE* was twice as high as for hornbeam. The total color difference between the color at the end and at the beginning of drying was 8.7 for hornbeam and 18.9 for maple. [ABSTRACT FROM AUTHOR]

In wood processing, wood is exposed to an environmental temperature of less than 0 °C for some time, which mainly occurs during the air drying of wood in the winter months, or when lumber is stored in wood piles outdoors before the kiln drying process. In these cases, the wood freezing process increases the degree of freezing of the wood, subsequently significantly affecting the process of its heating during further processing (for example, in the cutting process). The most common method is heating by humid air, during the hot air drying of wood. We analyzed the temperature profiles on a cross-section of wood and moisture losses due to the freezing process and the size of moisture gradients. We compared theoretical calculations of the time required for defrosting and heating of wood with the experimentally measured values. The results show that the moisture content (MC) of wood has a remarkable effect on the wood freezing process. In samples with an average MC of 35.47%, the temperature drop was faster. After 10 h, the temperatures on the entire cross-section of the samples reached the lowest value of −13.2 °C. In samples with an average initial MC of 81.38%, three stages of temperature reduction in the wood were observed. The temperature dropped and the lowest temperature of −20.11 °C was reached after 24 h. The defrosting and heating process of samples with lower MC was significantly easier. The desired temperature of 65 °C in the middle of the samples was reached in 2 h and 20 min. The total time to defrost and heat the second group of samples (MC > FSP) was 3 h 30 min. [ABSTRACT FROM AUTHOR]

The influence of the impregnation process of pine wood (Pinus sylvestris L.) samples on the electrical resistance changes and the moisture-content measurement accuracy is presented in this paper. In this study, the resistances of impregnated and nonimpregnated green pine timber harvested from northern Poland were compared. An impregnation method based on a vacuum-pressure chamber was used. Copper salts were applied as the impregnated solutions. The obtained results of the electrical resistance comparison showed a dependence of wood resistance on the moisture content. Higher conductivity occurred in impregnated wood samples filled with copper salt compared with wood samples without impregnation. Noticeable differences in the electrical resistance values were observed when the wood moisture content was significantly above the Fibre Saturation Point (FSP). [ABSTRACT FROM AUTHOR]

The structure of a bark as a component of a living tree is completely different from wood. Different structures significantly influence the physical and mechanical properties of the bark. In the processing of logs, it is in most cases necessary to separate the bark from the wood. Problems can arise mainly in the pulp and paper industry. The research focused on the impact of storage conditions on shear strength, showing that the value of shear strength decreased remarkably due to the storage. A decrease in strength can mainly be explained by the changes in the moisture content of bark, remarkably affected by the surrounding environment (climate). The research showed that three months of storage seemed to be the most appropriate and effective period for removing the bark in the case of beech logs and that a storage time of up to five months was the best in the case of oak logs. [ABSTRACT FROM AUTHOR]

Beech wood is mainly used for furniture, plywood, decorative veneer manufacturing or packaging. Timber or lumber is traditionally dried in kilns by processes often taking several weeks. This research deals with more rapid process called contact-drying process. Drying was performed using the heating plates with a temperature of 160 °C and pressures of 1.0 MPa, 1.4 MPa and 1.8 MPa. The results were compared to conventional warm-air drying. The warm-air drying mode was divided into two phases, with and without free water and bound water in the dried wood. The density of the samples increased remarkably during the contact-drying. The effect of the pressure of the heating plates was substantial. The difference in the average density between the pressure of 1.0 MPa and 1.8 MPa was more than 22 kg·m−3. The pressure of the heating plates affected the process and the resulting change in the sample thickness. The change in the sample thickness was more considerable in the case of the tangential samples. The thickness did not increase significantly after air conditioning. During contact-drying, the hygroscopicity and absorptivity of wood reduced on average by 21.24% and 25%, respectively, compared to warm-air drying. [ABSTRACT FROM AUTHOR]