Search

To investigate the mechanism of polypropylene fiber (PPF) on the rheological and thixotropic properties of cemented paste backfill containing mineral admixtures, the concept of water film thickness (WFT) was introduced. The packing density of the tailings-binder-PPF (TBP) system was measured in dry and wet conditions and the WFT was calculated accordingly. Additionally, the rheological parameters (yield stress, thixotropy, etc.) of the fiber-reinforced cemented paste backfill (FRCPB) were quantified. The results demonstrate that the wet packing test is a more appropriate method for measuring the packing density of the TBP system. The PPF length has a slight adverse effect on the packing density, and the packing density initially increases and then decreases with the PPF content. The reasons can be attributed to the filling effect and wedge effect of the fibers, respectively. In addition to the packing density, the thixotropy of FRCPB is also affected by the interaction of fibers. WFT is a crucial factor affecting the yield stress of FRCPB, with which it exhibits a strong linear relationship. The study identified that the optimum PPF content for enhancing the rheological and thixotropic properties of CPB is 0.2%, with a fiber length of 9 mm, balancing flowability and stability for practical application in mining backfill operations. These insights can guide the optimization of CPB mixtures, enhancing their flowability and stability during placement in mined-out spaces. By improving the fill quality and reducing the risk of blockage during backfill operations, the results offer practical benefits in increasing the safety and efficiency of underground mining activities. [ABSTRACT FROM AUTHOR]

The rheological behavior and printing characteristics of the screen-printing slurry for Nd-Fe-B grain boundary diffusion are key factors that determine the quality of printing and magnetic performance. However, few studies have focused on the organic medium, a crucial material for slurry. In this paper, the rheology, thixotropy, and thermal decomposition behavior of the organic vehicle in Nd-Fe-B screen printing slurry were studied. The results show that the organic vehicle formed by terpineol and polyvinyl butyral (PVB) exhibits typical non-Newtonian fluid characteristics, with excellent rheology and thixotropy, ensuring that the slurry prepared from it has excellent static stability and printing consistency. Additionally, the carbon residue of the organic vehicle formed by terpineol and PVB is less than 0.1% at 900 °C, avoiding excessive carbon entering the magnet during the diffusion process. Moreover, studying the rheology and thixotropy of the organic vehicle through a rheometer can quickly screen the slurry system. This work provides valuable guidance for designing an organic vehicle for screen-printing slurry for Nd-Fe-B grain boundary diffusion in future research. [ABSTRACT FROM AUTHOR]

In this paper, with the application of a MARS 60 high-pressure rheometer, experimental tests are conducted on Shengli crude oil to test its gel point, viscosity and thixotropy under different static pressures. Consequently, the effect of static pressure on the rheological parameters of waxy crude oil is revealed. It is proven that with the increase in the static pressure, the gel point of Shengli crude oil increases linearly, and the viscosity also gradually increases. The power law equation is employed to describe the relationship between the apparent viscosity and shear rate of Shengli crude oil under different static pressures. With the increase in the static pressure, the consistency coefficient (K) increases linearly, and the rheological index (n) decreases linearly. The relationship between the viscosity of Shengli crude oil and the static pressure and shear rate can be obtained. The Cross thixotropic model is used to describe the thixotropic curve of Shengli crude oil under different static pressures. With the increase in the static pressure, the thixotropic coefficient of consistency (ΔK) and the structure fracture constant (b) increase linearly. This is because a high pressure results in high structure strength and strong non-Newton rheological behavior in gelled crude oil and also causes remarkable structure fracture in crude oil. The results in this paper can provide an important theoretical basis for crude oil production and transportation. [ABSTRACT FROM AUTHOR]

In this article, the particle concentration of finely dispersed copper(II) oxide nanosuspensions as precursors for reductive laser sintering (RLS) is optimized on the basis of rheological investigations. For this metallization process, a smooth, homogeneous and defect-free precursor layer is a prerequisite for adherent and reproducible copper structures. The knowledge of the rheological properties of an ink is crucial for the selection of a suitable coating technology as well as for the adjustment of the ink formulation. Different dilutions of the nanosuspension were examined for their rheological behavior by recording flow curves. A strong shear thinning behavior was found and the viscosity decreases exponentially with increasing dilution. The viscoelastic behavior was investigated by a simulated doctor blade coating process using three-interval thixotropy tests. An overshoot in viscosity is observed, which decreases with increasing thinning of the precursor. As a comparison to these results, doctor blade coating of planar glass and polymer substrates was performed to prepare precursor layers for reductive laser sintering. Surface morphology measurements of the resulting coatings using laser scanning microscopy and rheological tests show that homogeneous precursor layers with constant thickness can be produced at a particle–solvent ratio of 1.33. A too-high particle content results in an irregular coating layer with deep grooves and a peak-to-valley height S z of up to 7.8 μm. Precise dilution control allows the fabrication of smooth surfaces with a S z down to 1.5 μm. [ABSTRACT FROM AUTHOR]

In many food applications, the mechanical properties of fats play a critical role in determining the processing performance of fat-rich products. In fact, fat crystal networks form a particular class of soft materials that exhibit viscoelastic properties. The uniqueness of the mechanical response is intricately linked to the hierarchical nature of the system, as fats possess a complex architecture encompassing features at different scale levels (i.e., length scales). Since the discovery of crystalline nanoplatelets (CNPs), it has been hypothesized that CNPs are the basic building blocks of lipid networks and that CNPs are the responsible units for the mechanical properties of fats. This hypothesis, however, has only been partially tested. In this article, we examine which units could be responsible (e.g., lamellae, CNP, CNP aggregates) for the mechanical breakdown of fat crystal networks, through Rheo-USAXS in beamline ID02 (ESRF, Grenoble, France). Time-resolved USAXS profiles were acquired during the three steps of a three-interval thixotropy test (3iTT), namely, pre-shear, shear and recovery. The results were then utilized to evidence which specific length scale is arranged (i.e., orientated) during rheological breakdown. The findings suggest that, at the tested shear rates, orientation is only visible from 250 nm onwards, suggesting that the rheological breakdown of triglycerides is primarily driven by the orientation, and possible disruption, of CNP aggregates. These results reveal the critical role of CNP aggregates in the mechanical properties of fats. In the longer term, we believe this study will steer future research toward a more focused understanding of CNP aggregation and disaggregation dynamics. [ABSTRACT FROM AUTHOR]

In the realm of cementitious materials, integrating nanoclay shows promise in enhancing properties relevant to additive manufacturing. This paper presents a novel mathematical model that combines simple empirical dissolution/nucleation Avrami-like kinetics with a thixotropic kinetics equation. To analyze the initial exothermic peak, two sets of the calculation parameter function are built to describe the exothermic rate as a function of time, following an exponential pattern. This allows for the prediction of the changes in cumulative heat and heat rate during hydration, considering different concentrations of nanoclay. In the rheological aspect, the relationship between shear stress, shear rate, and time is modeled as a combination of exponential dependencies. This enables the prediction of the variations in shear stress with one variable while holding the other constant (either time or shear rate). By integrating these aspects, this model effectively describes both the first exothermal peak and the rheological behavior during cement hydration with the inclusion of nanoclay. Validated against experimental results, these models demonstrate good accuracy (overall below 3% error), reliability, and applicability. The findings offer valuable insights into the thermal and rheological aspects of concrete printing, enabling informed design decisions for both scientific and industrial applications. [ABSTRACT FROM AUTHOR]

The formulation of biphasic gels as potential semi-solid carriers for hydrophilic and lipophilic active substances is promising for the development of pharmaceutical preparations. The aim of this study was to design a stable bigel composition and to determine the influence of the organogel/hydrogel ratio on the gel's physical-chemical and structural-mechanical properties. The investigated compositions of organogel/hydrogel remained stable at ratios ranging from 5/95 to 40/60. After texture and microstructure analysis, bigels with 20/80 and 25/75 ratios were selected as carriers for the active ingredients, sodium diclofenac and camphor, for use as topical preparations for the treatment of muscle-joint inflammation and pain. Although other researchers have published data on the preparation and evaluation of bigels, there are no scientific results on the development of a two-phase gel with our proposed combination of APIs. Sodium diclofenac release was found to be higher when combined with camphor, which revealed the advantages of the biphasic formulation. The pseudoplastic behavior, thixotropy, and thermal stability of flow of the studied bigel samples was investigated by rheological analysis. Ongoing stability studies confirmed the minimal 6-month period. [ABSTRACT FROM AUTHOR]

Hexakis(2-alkoxy-1,5-phenyleneimine) macrocycles were synthesized using a simple one-pot procedure through precipitation-driven cyclization. The acetal-protected AB–type monomers, 2-alkoxy-5-aminobenzaldehyde diethyl acetals, underwent polycondensation in water or acid-containing tetrahydrofuran. The precipitation–driven cyclization, based on imine dynamic covalent chemistry and π–stacked columnar aggregation, played a decisive role in the one–pot synthesis. The progress of the reaction was analyzed using MALDI–TOF mass spectrometry. The macrocycles with alkoxy chains were soluble in specific organic solvents, such as chloroform, allowing their structures to be analyzed using NMR. The shape-anisotropic, nearly planar, and shape-persistent macrocycles aggregated into columnar assemblies in polymerization solvents, driven by aromatic π-stacking. The octyloxylated macrocycle OcO–Cm6 exhibited an enantiotropic columnar liquid crystal-like mesophase between 165 °C and 197 °C. In the SEM image of (S)-(–)-3,7-dimethyloctyloxylated macrocycle (–)BCO–Cm6, columnar substances with a diameter of 200–300 nm were observed. The polymerization solution for the 2-(2-methoxyethoxy)ethoxy)ethoxylated macrocycle (TEGO–Cm6) gelled, and showed thixotropic properties by forming a hydrogen bond network. [ABSTRACT FROM AUTHOR]

It is known that 3D printable concrete mixtures can be costly because they contain high dosages of binder and that the drying-shrinkage performance may be adversely affected. Mineral additives and fibers are generally used to control these negative aspects. In this study, the use of silica fume, a natural viscosity modifying admixture, was investigated to improve the rheological and thixotropic behavior of 3D printable concrete mixtures reinforced with polypropylene fiber (FR-3DPC). The effect of increasing the silica fume utilization ratio in FR-3DPC on the compressive strength (CS), flexural strength (FS), and drying-shrinkage (DS) performance of the mixtures was also examined. A total of five FR-3DPC mixtures were produced using silica fume at the rate of 3, 6, 9, and 12% of the cement weight, in addition to the control mixture without silica fume. As a result of the tests, the dynamic yield stress value decreased with the addition of 3% silica fume to the control mixture. However, it was found that the dynamic yield stress and apparent viscosity values of the mixtures increased with the addition of 6, 9, and 12% silica fume. With the increase in the use of silica fume, the CS values of the mixtures were generally affected positively, while the FS and DS behavior were affected negatively. [ABSTRACT FROM AUTHOR]

We propose a methodology for the rheological characterization of a semisolid metal slurry using experimental squeeze-flow data. The slurry is modeled as a structural thixotropic viscoplastic material, obeying the regularized Herschel–Bulkley constitutive equation. All rheological parameters are assumed to vary with the structure parameter that is governed by first-order kinetics accounting for the material structure breakdown and build-up. The squeeze flow is simulated using finite elements in a Lagrangian framework. The evolution of the sample height has been studied for wide ranges of the Bingham and Reynolds numbers, the power-law exponent as well as the kinetics parameters of the structure parameter. Systematic comparisons have been carried out with available experimental data on a semisolid aluminum alloy (A356), where the sample is compressed from its top side under a specified strain of 80% at a temperature of 582 °C, while the bottom side remains fixed. Excellent agreement with the experimental data could be achieved provided that at the initial instances (up to 0.01 s) of the experiment, the applied load is much higher than the nominal experimental load and that the yield stress and the power-law exponent vary linearly with the structure parameter. The first assumption implies that a different model, such as an elastoviscoplastic one, needs to be employed during the initial stages of the experiment. As for the second one, the evolution of the sample height can be reproduced allowing the yield stress to vary from 0 (no structure) to a maximum nominal value (full structure) and the power-law exponent from 0.2 to 1.4, i.e., from the shear-thinning to the shear-thickening regime. These variations are consistent with the internal microstructure variation pattern known to be exhibited by semisolid slurries. [ABSTRACT FROM AUTHOR]

Third-degree burn injuries pose a significant health threat. Safer, easier-to-use, and more effective techniques are urgently needed for their treatment. We hypothesized that covalently bonded conjugates of fatty acids and tripeptides can form wound-compatible hydrogels that can accelerate healing. We first designed conjugated structures as fatty acid–aminoacid1–amonoacid2–aspartate amphiphiles (Cn acid–AA1–AA2–D), which were potentially capable of self-assembling into hydrogels according to the structure and properties of each moiety. We then generated 14 novel conjugates based on this design by using two Fmoc/tBu solid-phase peptide synthesis techniques; we verified their structures and purities through liquid chromatography with tandem mass spectrometry and nuclear magnetic resonance spectroscopy. Of them, 13 conjugates formed hydrogels at low concentrations (≥0.25% w/v), but C8 acid-ILD-NH2 showed the best hydrogelation and was investigated further. Scanning electron microscopy revealed that C8 acid-ILD-NH2 formed fibrous network structures and rapidly formed hydrogels that were stable in phosphate-buffered saline (pH 2–8, 37 °C), a typical pathophysiological condition. Injection and rheological studies revealed that the hydrogels manifested important wound treatment properties, including injectability, shear thinning, rapid re-gelation, and wound-compatible mechanics (e.g., moduli G″ and G′, ~0.5–15 kPa). The C8 acid-ILD-NH2(2) hydrogel markedly accelerated the healing of third-degree burn wounds on C57BL/6J mice. Taken together, our findings demonstrated the potential of the Cn fatty acid–AA1–AA2–D molecular template to form hydrogels capable of promoting the wound healing of third-degree burns. [ABSTRACT FROM AUTHOR]

Some non-Newtonian fluids have time-dependent rheological properties like a shear stress that depends on the shear history or a stress overshoot that is a function of the resting time, when fluid movement is started. The rheological properties of such complex fluids may not stay constant while they are used in an industrial process, and it is therefore desirable to measure these properties frequently and with a simple and robust device like a pipe rheometer. This paper investigated how the time-dependent rheological properties of a thixotropic and viscoelastic shear-thinning fluid can be extracted from differential pressure measurements obtained at different flowrates along a circular pipe section. The method consists in modeling the flow of a thixotropic version of a Quemada fluid and solving the inverse problem in order to find the model parameters using the measurements made in steady-state conditions. Also, a Maxwell linear viscoelastic model was used to reproduce the stress overshoot observed when starting circulation after a resting period. The pipe rheometer was designed to have the proper features necessary to exhibit the thixotropic and viscoelastic effects that were needed to calibrate the rheological model parameters. The accuracy of rheological measurements depends on understanding the effects that can influence the observations and on a proper design that takes advantage of these side effects instead of attempting to eliminate them. [ABSTRACT FROM AUTHOR]

The structures and properties of hydrophobic association polymers can be controlled using micelles. In this work, we synthesize a reactive hydrophobic surfactant monomer, KS-3, from oleic acid, N,N-dimethylpropylenediamine, and allyl chloride. A strong synergistic effect between KS-3 and cocamidopropyl betaine in aqueous solution enhances the hydrophilic dispersibility of KS-3, thereby transforming spherical micelles into cylindrical micelles. KS-3 was grafted onto a polyacrylamide chain via aqueous free-radical polymerization to obtain RES, a hydrophobic association polymer. Structural analysis revealed that the RES polymers assembled in wormlike micelles were more tightly arranged than those assembled in spherical micelles, resulting in a compact network structure in water, smooth surface, and high thermal stability. Rheological tests revealed that the synthesized polymers with wormlike and spherical micelles exhibited shear-thinning properties along with different structural strengths and viscoelasticities. Therefore, controlling the micellar state can effectively regulate the polymer properties. The polymers obtained through wormlike micelle polymerization have potential applications in fields with high demands, such as drug release, water purification, and oilfield development. [ABSTRACT FROM AUTHOR]

The structural build-up of cementitious materials is the subject of more and more attention since it conditions several processes such as formwork pressure and multi-layer casting. However, this phenomenon originating from flocculation and chemical changes is complex and its reversibility is not clearly elucidated. The aim of this paper is to examine the effect of temperature on the reversibility of structural build-up. The results show that irreversible structural build-up remains negligible despite a rise in temperature. It represents between 0.5–7.3% of the total structural build-up. The addition of SCMs allows for a decrease in this irreversible structural build-up. Therefore, a large part of the chemical contribution is expected to be reversible. The effect of temperature can be explained by the increase in the dissolution rate leading to an increase in flocculation and to the bridging effect induced by early hydrates. Finally, the results suggest that the interparticle distance could be the key parameter governing the irreversibility of structural build-up. [ABSTRACT FROM AUTHOR]

Investigating the structural evolution of particulate gels is a very challenging task due to their vulnerability and true flow characteristics. In this work, deeper insight into the rheological properties of gel fuels filled with fumed silica (FS) and aluminum microparticles (Al MPs) was gained by changing shear procedures. Firstly, the flow curves were found to no longer follow the monotonic power law and exhibited subtle thixotropic responses. As the shear rate increased, the gel structure underwent a transition from local shear to bulk shear in the nonlinear region after yielding. This finding reveals the prevalence of nonideal local shear in industry. Secondly, the time-dependent rheological responses demonstrated that the strength spectrum of gel fuels depends on the applied shear rate, with stress relaxation more easily observed at lower shear rates. Those results involved the structural disruption, recovery, and equilibrium of particulate gels from two scales of shear rate and shear time. [ABSTRACT FROM AUTHOR]

In order to analyze the thixotropy of mastic asphalt concrete during the mixing process, the factors affecting the thixotropy of mastic asphalt binder and asphalt mastic are studied, and the measures to shorten the mixing time of mastic asphalt mixture are given. The dynamic viscosity of mastic asphalt binder and asphalt mastic with time and shear rate is obtained via the step frequency method, and the thixotropic constitutive models of mastic asphalt binder and asphalt mastic are constructed by structural dynamics model, exponential equation, and extended exponential equation respectvely. The improved time thixotropy index is used to analyze the effects of asphalt type, asphalt–aggregate ratio, filler type, heating temperature, and shear rate, and the laws of various factors affecting the thixotropy of mastic asphalt binder and asphalt mastic are obtained. The research shows that the extended exponential model can better characterize the thixotropy of mastic asphalt binder and asphalt mastic under different shear rates. When the amount of lake asphalt or cement is increased, the viscosity of the system and the mixing time to reach a steady viscosity increases; that is, the mixing time needs to be increased. Increasing shear temperature does not change the time parameter to reach steady viscosity; that is, it cannot shorten mixing time. When the shear rate is increased, the time for the system to reach the steady viscosity will be shortened; that is, the time for mixing the mixture can be shortened. [ABSTRACT FROM AUTHOR]

The aim of this study was to assess the gelling potential of chiral oxalamide derivatives in vegetable oils. Special emphasis was given to the potential applications of the examined oil gels as sustained delivery systems and as fat substitutes in food products. The applicability of oil gelators is envisaged in food, cosmetics, and the pharmaceutical industry. The regulations requiring the elimination of saturated fats and rising concerns among consumers health motivated us to investigate small organic molecules capable of efficiently transforming from liquid oil to a gel state. The oxalamide organogelators showed remarkable gelation efficiency in vegetable oils, thermal and mechanical stability, self-healing properties, and a long period of stability. The physical properties of the gels were analysed by TEM microscopy, DSC calorimetry, and oscillatory rheology. The controlled release properties of acetylsalicylic acid, ibuprofen, and hydrocortisone were analysed by the LC–MS method. The influence of the oil type (sunflower, soybean, and olive oil) on gelation efficiency of diverse oxalamide derivatives was examined by oscillatory rheology. The oxalamide gelators showed thermoreversible and thixotropic properties in vegetable oils with a minimum gelation concentration of just 0.025 wt%. The substitution of palm fats with gelled sunflower oil applied in cocoa and milk spreads at gelator concentrations lower than 0.2 wt% have shown promising viscoelastic properties compared to that of the original food products. [ABSTRACT FROM AUTHOR]

Self-healing, thermoresponsive hydrogels with a triple network (TN) were obtained by copolymerizing N-isopropyl acryl amide (NiPAAm) with polyvinyl alkohol (PVA) functionalized with methacrylic acid and N,N′-methylene bis(acryl amide) crosslinker in the presence of low amounts (<1 wt.%) of tannic acid (TA). The final gels were obtained by crystalizing the PVA in a freeze-thaw procedure. XRD, DCS, and SEM imaging indicate that the crystallinity is lower and the size of the PVA crystals is smaller at higher TA concentrations. A gel with 0.5 wt.% TA has an elongation at a break of 880% at a tension of 1.39 MPa. It has the best self-healing efficiency of 81% after cutting and losing the chemical network. Step-sweep strain experiments show that the gel has thixotropic properties, which are related to the TA/PVA part of the triple network. The low amount of TA leaves the gel with good thermal responsiveness (equilibrium swelling ratio of 13.3). Swelling-deswelling loop tests show enhanced dimensional robustness of the hydrogel, with a substantial constancy after two cycles. [ABSTRACT FROM AUTHOR]

Direct ink writing (DIW) requires careful selection of ink composition with specific rheological properties, and it has limitations, such as the inability to create overhanging parts or branched geometries. This study presents an investigation into enhancing the 3D printing process through the use of a heterophase system, aiming to overcome these limitations. A modification was carried out in the 3D printer construction, involving adjustments to the structural elements responsible for the extrusion device's movement. Additionally, a method for obtaining a heterophase system based on gelatin microparticles was developed to enable the 3D printing process with the upgraded printer. The structure and rheological properties of the heterophase system, varying in gelatin concentration, were thoroughly examined. The material's viscosity ranged from 5.4 to 32.8 kPa·s, exhibiting thixotropic properties, pseudoplastic behavior, and long-term stability at 20 °C. The developed 3D printing technology was successfully implemented using a heterophase system based on different gelatin concentrations. The highest product quality was achieved with a heterophase system consisting of 4.5 wt.% gelatin, which exhibited a viscosity of 22.4 kPa·s, enabling the production of products without spreading or compromising geometrical integrity. [ABSTRACT FROM AUTHOR]

The influence of the components of plaster mortars on their properties is considered in a lot of studies at a qualitative level without searching for optimal compositions of these multicomponent composite materials. The purpose of this study was to obtain the experimental–statistical models based on the results of the designed experiment, allowing the influence of light fillers and polymer admixtures on the properties of the mortars to be evaluated and analysed; the compositions complying with specified requirements and compromised optimally by a number of properties should be found. The quantities of fine limestone and perlite as well as of the hydroxyethyl methyl cellulose and dispersible polymer were varied in the experiment. The effective viscosity and thixotropy of the mix, compression, tensile, adhesive strength, frost resistance, and density of hardened mortars were determined for 18 compositions according to the experiment design. The obtained models have allowed the individual and synergetic effects of mix components to be evaluated. The fine perlite has turned out to have the greatest positive effect on the properties. This porous filler increases the strength while decreasing the density of the mortars. It is shown how the composition complying with specified requirements—and the best based on several properties—has been found. [ABSTRACT FROM AUTHOR]

Over the last decade, efforts have been oriented toward the development of suitable gels for 3D printing, with controlled morphology and shear-thinning behavior in well-defined conditions. As a multidisciplinary approach to the fabrication of complex biomaterials, 3D bioprinting combines cells and biocompatible materials, which are subsequently printed in specific shapes to generate 3D structures for regenerative medicine or tissue engineering. A major interest is devoted to the printing of biomimetic materials with structural fidelity after their fabrication. Among some requirements imposed for bioinks, such as biocompatibility, nontoxicity, and the possibility to be sterilized, the nondamaging processability represents a critical issue for the stability and functioning of the 3D constructs. The major challenges in the field of printable gels are to mimic at different length scales the structures existing in nature and to reproduce the functions of the biological systems. Thus, a careful investigation of the rheological characteristics allows a fine-tuning of the material properties that are manufactured for targeted applications. The fluid-like or solid-like behavior of materials in conditions similar to those encountered in additive manufacturing can be monitored through the viscoelastic parameters determined in different shear conditions. The network strength, shear-thinning, yield point, and thixotropy govern bioprintability. An assessment of these rheological features provides significant insights for the design and characterization of printable gels. This review focuses on the rheological properties of printable bioinspired gels as a survey of cutting-edge research toward developing printed materials for additive manufacturing. [ABSTRACT FROM AUTHOR]

An asphalt mastic has thixotropic characteristics that significantly influence its fatigue and healing performance. Therefore, understanding the thixotropy of an asphalt mastic is clearly of great importance. However, research in this area is still in the early stages. This study focuses on self-heating as one of the biasing performances of asphalt material by analyzing the viscosity, stress, and hysteresis loops the of asphalt mastics under cyclic shear loading. Twelve types of asphalt mastics fabricated with asphalt, as well as different types of mineral filler, were selected to examine thixotropy. In addition, the filler/asphalt ratio was examined via the hysteresis technique to analyze the hysteresis loop and the viscosity–shear rate. The thixotropic potential function was also studied from the energy viewpoint. The results show that asphalt mastics with different asphalt binders, mineral fillers, and filler volume fractions showed hysteresis loops for shear stress versus shear rate diagrams. With an increase in the loading times of the cyclic load, the area of the hysteresis loop gradually decreases, and the hysteresis area most likely features a relatively stable value. The thixotropy of the asphalt can be significantly reduced by adding filler, and different types of mineral filler can slightly influence the thixotropy. The viscosity decreases with an increase in the shear rate, and it gradually recovers with a decrease in the shear rate. The greater the filler/asphalt ratio, the greater the viscosity, and the faster the viscosity's descent is with the prolongation of time. Due to the existence of a higher amount of filler content, the recovery of a viscosity crack is more difficult. For asphalt mastics with high filler/asphalt ratios, the thixotropic mechanism can be explained via particle agglomeration and the depolymerization theory. For asphalt mastics with low and medium filler/asphalt ratios, the thixotropic mechanism can be explained via the particle chain theory. The damage and recovery of the internal structure of an asphalt mastic can be characterized by the structural failure potential function and the structural recovery potential function, respectively. [ABSTRACT FROM AUTHOR]

Despite the advantageous benefits offered by self-compacting concrete, its uses are still limited due to the high pressure exerted on the formwork. Different parameters, such as those related to concrete mix design, the properties of newly poured concrete, and placement method, have an impact on form pressure. The question remains unanswered on the degree of the impact for each parameter. Therefore, this study aims to study the level of impact of these parameters, including slump flow, T500 time, fresh concrete density, air content, static yield stress, concrete setting time, and concrete temperature. To mimic the casting scenario, 2 m columns were cast at various casting rates and a laboratory setup was developed. A pressure system that can wirelessly and continuously record pressure was used to monitor the pressure. Each parameter's impact on the level of pressure was examined separately. Casting rate and slump flow were shown to have a greater influence on pressure. The results also demonstrated that, while higher thixotropy causes form pressure to rapidly decrease, a high casting rate and high slump flow lead to high pressure. This study suggests that more thorough analysis should be conducted of additional factors that may have an impact, such as the placement method, which was not included in this publication. [ABSTRACT FROM AUTHOR]

Organic rheology modifiers, especially superplasticizers and viscosity-modifying admixtures (VMAs), have become key components for the workability optimization of modern concrete. The development of these admixtures is crucial to the further performance improvement of modern concrete under different casting and service conditions. Many of the former reviews have summarized research advances in respect of these admixtures from chemical and material perspectives, focusing on the effects of structure and the performance. In this paper, from a rheological perspective, an overview is provided of the microscale behavior of polycarboxylate (PCE) superplasticizers and VMAs (e.g., adsorption, conformation, and bridging) in terms of the evolution of the microstructure of the paste, the effect of chemical structure on the yield stress, the apparent viscosity and thixotropy of cement-based materials, and the structure design of these admixtures. Most importantly, in addition to a general discussion with assumptions (monolayer adsorption of a "flat" conformation, with each molecule on a single particle; statistical polymer composition), special conditions (e.g., preferential adsorption, depletion effects, hydration modification effects, and the polydispersity of the polymer composition) are discussed. Newly developed admixtures, realized through regulation of the microscale behavior, and by the modification of adsorption, topological structure, and molecular frame, are introduced. [ABSTRACT FROM AUTHOR]

Thixotropic behavior describes a time-dependent rheological behavior characterized by reversible changes. Fresh cementitious materials often require thixotropic behavior to ensure sufficient workability and proper casting without vibration. Non-thixotropic behavior induces a workability loss. Cementitious materials cannot be considered as an ideal thixotropic material due to cement hydration, which leads to irreversible changes. However, in some cases, cement paste may demonstrate thixotropic behavior during the dormant period of cement hydration. The aim of this work is to propose an approach able to quantify the contribution of cement hydration during the dormant period and to examine the conditions under which the cement paste may display thixotropic behavior. The proposed approach consists of a succession of stress growth procedures that allow the static yield stress to be measured. For an inert material, such as a calcite suspension, the structural build-up is due to the flocculation induced by attractive Van der Waals forces. This structural build-up is reversible. For cement paste, there is a significant increase in the static yield stress due to cement hydration. The addition of superplasticizer allows the thixotropic behavior to be maintained during the first hours due to its retarding effect. However, an increase in the superplasticizer dosage leads to a decrease in the magnitude of the Van der Waals forces, which can erase the thixotropic behavior. [ABSTRACT FROM AUTHOR]

Nanogel is a promising drug delivery approach to improve the pharmacokinetics and pharmacodynamic prospect of phytopharmaceuticals. In the present review, phytopharmaceuticals with astonishing therapeutic utilities are being explored. However, their in vivo delivery is challenging, owing to poor biopharmaceutical attributes that impact their drug release profile, skin penetration, and the reach of optimal therapeutic concentrations to the target site. Nanogel and its advanced version in the form of nanoemulgel (oil-in-water nanoemulsion integrated gel matrix) offer better therapeutic prospects than other conventional counterparts for improving the biopharmaceutical attributes and thus therapeutic efficacy of phytopharmaceuticals. Nanoemulgel-loaded phytopharmaceuticals could substantially improve permeation behavior across skin barriers, subsequently enhancing the delivery and therapeutic effectiveness of the bioactive compound. Furthermore, the thixotropic characteristics of polymeric hydrogel utilized in the fabrication of nanogel/nanoemulgel-based drug delivery systems have also imparted improvements in the biopharmaceutical attributes of loaded phytopharmaceuticals. This formulation approach is about to be rife in the coming decades. Thus, the current review throws light on the recent studies demonstrating the role of nanogels in enhancing the delivery of bioactive compounds for treating various disease conditions and the challenges faced in their clinical translation. [ABSTRACT FROM AUTHOR]

Geopolymer composites can be used as a proper substitute for ordinary Portland cement, which can reduce carbon dioxide (CO2) emissions and make rational use of industrial waste. In this study, an investigation of the workability and compressive strength of geopolymer composites was carried out through a series of experiments, such as slump flow test, consistency meter test and compressive strength test, to clarify the interaction mechanism among superplasticizer (SP), polyvinyl alcohol (PVA) fiber, Nano-SiO2 (NS) and geopolymer composites, thereby improving the properties of engineered composites. The results showed that with the increase in PVA fiber content, the flowability of geopolymer composites decreased, while the thixotropy increased. With the increase in the NS content, the flowability of geopolymer composites first increased and then decreased, reaching its best at 1.0%, while the thixotropy was the opposite. With the increase in the SP content, the flowability of geopolymer composites increased, while the thixotropy decreased. A significant correlation between thixotropy and flowability of geopolymer composites was found (R2 > 0.85). In addition, the incorporation of single PVA fiber or NS significantly improved the compressive strength of geopolymer composites. Specifically, the compressive strength of geopolymer composites with 0.8% content PVA fiber (60.3 MPa) was 33.4% higher than that without PVA fiber (45.2 MPa), and the compressive strength of geopolymer composites with 1.5% content NS (52.6 MPa) was 16.4% higher than that without NS (45.2 MPa). Considering the synergistic effect, it is found that the compressive strength of geopolymer composites (58.5–63.3 MPa) was significantly higher than that without PVA fiber (45.2–52.6 MPa). However, the flowability and compressive strength of geopolymer composites were only slightly improved compared to that without NS. With the increase in the SP content, the compressive strength of geopolymer composites showed a trend of a slight decrease on the whole. Consequently, the results of this study may be useful for further research in the field of repair and prevention of the delamination of composite structures. [ABSTRACT FROM AUTHOR]

Formwork lateral pressures are critical with respect to engineering safety, and laboratory tests are often limited by time, height, etc. Formwork lateral pressures are related to early concrete fluid behavior (e.g., thixotropy). In this paper, we propose the use of ultra-deep underground diaphragm walls instead of formwork for conventional lateral pressure testing. During the construction process, three measurement points were set up in an ultra-deep diaphragm wall at −40 m, −80 m and −100 m. The concrete was divided into 22 casts, and the development of lateral pressure and the effect of time on lateral pressure were observed under each of the casts. We found that the characteristic height of all three measurement points was approximately 21 m. The average casting speed for this test was 16.846 m/h, with the fastest speed of 32.148 m/h. A time-dependent phenomenon of rapid rise and fall in lateral pressure with each casting was observed. This method provides a new way to conceptualize formwork lateral pressure, with the advantages of long testing time, high casting height and multiple tests, not only for formwork lateral pressure but also for early age thixotropy measurement of concrete. [ABSTRACT FROM AUTHOR]

Thixotropy is a fascinating feature present in many gel systems that has garnered a lot of attention in the medical field in recent decades. When shear stress is applied, the gel transforms into sol and immediately returns to its original state when resting. The thixotropic nature of the hydrogel has inspired scientists to entrap and release enzymes, therapeutics, and other substances inside the human body, where the gel acts as a drug reservoir and can sustainably release therapeutics. Furthermore, thixotropic hydrogels have been widely used in various therapeutic applications, including drug delivery, cornea regeneration and osteogenesis, to name a few. Because of their inherent biocompatibility and structural diversity, peptides are at the forefront of cutting-edge research in this context. This review will discuss the rational design and self-assembly of peptide-based thixotropic hydrogels with some representative examples, followed by their biomedical applications. [ABSTRACT FROM AUTHOR]

In this work, the rheological behavior of passion fruit peel extract was determined at different temperatures (5–40 °C) and peel content in the extract (40–55% w/w). The extract was obtained after blanching the passion fruit peels at 95 °C for 5 min, then they were crushed to reduce their size, water was added, and finally, they were subjected to liquefaction and subsequent filtration. Rheological measurements were made using a rheometer with a plate and plate geometry. Extract samples were adequately described by the power-law model exhibiting pseudoplastic behavior, without the presence of thixotropy. The temperature did not influence the flow behavior index, but the consistency coefficient did. The dynamic study (the temperature sweep test) showed that passion fruit peel extract exhibits a more elastic than viscous behavior, typical of a gel. [ABSTRACT FROM AUTHOR]

The rapid advancement of 3D concrete printing (3DCP) and the development of relevant cementitious material compositions can be seen in the last few decades. The commonly used 3DCP method is to build the structure layer by layer after extruding the material through a nozzle. Initially, the pumping and extrusion of the material should be done with considerable fluidity and workability. The extruded layers should retain their shape immediately after extruding and depositing. While constructing the structure in a layerwise manner, the bottom layers should have enough early age strength to support the layers at the top. Therefore, at different processes in 3DCP, the rheological requirement is contradictory. As the rheology of the material is the deterministic factor which decides the fluidity or workability of the mix, proper rheological characterization should be completed accurately. In some instances, due to the higher stiffness, and higher time and rate-dependent material behavior (thixotropic behavior) compared to the conventional concrete, standard rheology measurement techniques have many limitations when used for 3DCP material. Therefore, non-conventional and novel techniques can be implemented with suitable material models to characterize the rheology of 3DCP material. In this study, a comprehensive review was conducted on conventional and non-conventional methods used for characterizing the rheological parameters for 3DCP material. The previously conducted studies were highlighted with the targeted 3DCP processes in the study (if applicable), and rheological parameters achieved from the test (i.e., yield stress, viscosity, and thixotropy). In addition, some experimental studies were conducted to compare several selected testing methods. The rheological parameters achieved from different test methods were compared to identify the similarities, dissimilarities, pros, and cons between the test methods. Furthermore, the extrudability and buildability studies were conducted for the mixes to demonstrate the usage of the mixes in 3DCP applications and to correlate the achieved rheological parameters with these processes. [ABSTRACT FROM AUTHOR]

Gel fuel potentially combines the advantages of solid fuel and liquid fuel due to its special rheological properties, which have essential impacts on the application of gel fuel in propulsion systems. In this paper, we study the rheological property of organic kerosene gel through a series of measurements on its viscosity as a function of the shear rate, temperature, and shear history. The measured datasets are then fitted with constitutive relationships between the viscosity and shear rate at three different levels: the power law shear-thinning model, the power law dependency on both the temperature and shear rate, and the thixotropic property. It is found that intense pre-shear could exhaust thixotropy and reduce viscosity of the kerosene gel. For the power law shear-thinning model, the consistency index increases with the gellant mass fraction, whereas the power law exponent remains constant. The dependence of viscosity on temperature could be well approximated by an empirical power law relationship. As for the thixotropic property of the kerosene gel, the fitted second-order kinetic model corresponds accurately to the viscosity at different shear rates and shear times. The constitutive models fitted in this work at different levels are consistent with each other and provide useful tools for further applications of organic kerosene gel fuel. [ABSTRACT FROM AUTHOR]

In this work, we outline the development of a thermodynamically consistent microscopic model for a suspension of aggregating particles under arbitrary, inertia-less deformation. As a proof-of-concept, we show how the combination of a simplified population-balance-based description of the aggregating particle microstructure along with the use of the single-generator bracket description of nonequilibrium thermodynamics, which leads naturally to the formulation of the model equations. Notable elements of the model are a lognormal distribution for the aggregate size population, a population balance-based model of the aggregation and breakup processes and a conformation tensor-based viscoelastic description of the elastic network of the particle aggregates. The resulting example model is evaluated in steady and transient shear forces and elongational flows and shown to offer predictions that are consistent with observed rheological behavior of typical systems of aggregating particles. Additionally, an expression for the total entropy production is also provided that allows one to judge the thermodynamic consistency and to evaluate the importance of the various dissipative phenomena involved in given flow processes. [ABSTRACT FROM AUTHOR]

The review is devoted to the analysis of the current state of understanding relationships among the deformation-induced structure transformations, observed rheological properties, and the occurrence of non-linear effects for polymer liquids (melts, solutions, and composites). Three levels of non-linearity are the base for consideration. The first one concerns changes in the relaxation spectra of viscoelastic liquids, which are responsible for weak non-linear phenomena. The second one refers to the strong non-linearity corresponding to such changes in the structure of a medium that leads to the emergence of a new relaxation state of a matter. Finally, the third one describes the deformation-induced changes in the phase state and/or the occurring of bifurcations and instability in flow and reflects the thermodynamic non-linear behavior. From a structure point of view, a common cause of the non-linear effects is the orientation of macromolecules and changes in intermolecular interaction, while a dominant factor in describing fluid dynamics of polymer liquids is their elasticity. The modern understanding of thixotropic effects, yielding viscoplastic materials, deformation-induced phase transition, and the experimental observations, demonstrating direct correlations between the structure and rheology of polymer liquids, are the main objects for discussion. All these topics are reviewed and discussed mainly on the basis of the latest five-year publications. [ABSTRACT FROM AUTHOR]

The rheopectic behavior of sacran aqueous solutions, a natural giant molecular polysaccharide with a molecular weight of 1.6 × 107 g/mol, was investigated. When a low shear was applied to 1.0 wt.% sacran solution, the shear viscosity increased from 7.2 to 34 Pa·s. The increment in the viscosity was enhanced as the shear rate decreased. The shear viscosity was independent of the time at a shear rate of 0.8 s-1; simultaneously, thixotropic behavior was observed at shear rates higher than 1.0 s-1. A crossover was observed at 0.15 wt.% for the concentration dependence of both the viscosity increase and zeta potential, which was the vicinity of the helix transition concentration or gelation concentration. It was clear that the molecular mechanism for the rheopexy was different at lower and higher regions of the crossover concentration. [ABSTRACT FROM AUTHOR]

The time-dependent role of cations was investigated by ageing four different aqueous solutions of cation chlorides. A linear correlation was found between the cations' Setchenov coefficient for the salting-out of benzene and the increase in the conductivity with time. The conductivity of the structure-breaking cations or the chaotropes increased more significantly with time than the conductivity of the kosmotropes. Since larger water clusters accelerate the proton or hydroxyl hopping mechanism, we propose that the structuring of the hydration shells of the chaotropes might be spontaneously enhanced over time. [ABSTRACT FROM AUTHOR]

In this work we review the literature for possible confirmation of a phenomenon that was proposed to develop when water is left to stand for some time undisturbed in closed vessels. The phenomenon has been termed thixotropy of water due to the weak gel-like behaviour which may develop spontaneously over time where ions and contact with hydrophilic surfaces seem to play important roles. Thixotropy is a property of certain gels and liquids that under normal conditions are highly viscous, whereas during mechanical processing their viscosity diminishes. We found experiments indicating water's self-organizing properties, long-lived inhomogeneities and time-dependent changes in the spectral parameters of aqueous systems. The large-scale inhomogeneities in aqueous solutions seem to occur in a vast number of systems. Long-term spectral changes of aqueous systems were observed even though the source of radiation was switched off or removed. And water was considered to be an active excitable medium in which appropriate conditions for self-organization can be established. In short, the thixotropic phenomenon of water is further indicated by different experimental techniques and may be triggered by large-scale ordering of water in the vicinity of nucleating solutes and hydrophilic surfaces. [ABSTRACT FROM AUTHOR]

The purpose of this work was to determine the influence of mechanical and electrical treatment on the electrical conductivity of aqueous solutions. Solutions were treated mechanically by iteration of two steps: 1:100 dilution and vigorous shaking. These two processes were repeated until extremely dilute solutions were obtained. For electrical treatment the solutions were exposed to strong electrical impulses. Effects of mechanical (as well as electrical) treatment could not be demonstrated using electrical conductivity measurements. However, significantly higher conductivity than those of the freshly prepared chemically analogous solutions was found in all aged solutions except for those samples stored frozen. The results surprisingly resemble a previously observed weak gel-like behavior in water stored in closed flasks. We suggest that ions and contact with hydrophilic glass surfaces could be the determinative conditions for the occurrence of this phenomenon. [ABSTRACT FROM AUTHOR]

In an experimental study, significantly higher conductivity values than those of freshly prepared chemically analogous solutions were found in aged (∼one year old) aqueous solutions, except for those stored frozen. The results surprisingly resemble a previously noticed phenomenon in liquid water, which develops when water is stored in closed vessels. This was observed as a disturbing phenomenon in gravimetric measurements and in luminescence spectroscopy measurements. The phenomenon was termed "autothixotropy of water" due to the weak gel-like behavior which develops spontaneously over time, in which ions seem to play an important role. Here, according to experimental results we propose that contact with hydrophilic surfaces also plays an important role. The role of the "autothixotropy of water" in proton transfer is also discussed. [ABSTRACT FROM AUTHOR]

Concrete 3D printing is a novel construction method that can bring new horizons to the construction industry. However, there are still many challenges that limit its capabilities. Despite the huge research efforts, to date, there are still no standardized acceptance criteria and guidelines for the evaluation of printing concrete. Therefore, the main objective of this research was to develop 3D printing mixes with different aggregate-to-binder (a/b) ratios (1.2, 1.5, and 1.8) and evaluate it in terms of its fresh printing properties, which include the workability, extrudability, setting time, open time, and buildability. The compressive strengths of cast and printed specimens were also tested to determine the effect of the layering process. The workability was evaluated using commonly used devices in the construction industry (slump and flow table test) and was monitored over time along with the penetration test to indicate the structuration rate of concrete. From the experimental results and observations, the flow test resulted in the best indication of the structuration rate (thixotropy) of concrete, followed by the penetration and slump tests. The a/b ratio affected all the investigated properties of the printing concrete. Higher a/b ratios resulted in increased structuration rate, buildability, and compressive strength of cast specimens. However, for printed specimens, the compressive strength decreased with the increase in a/b ratio due to increased thixotropy. Therefore, from the results of the present investigation, it can be concluded that high a/b ratios (>1.5) are not desirable for printing concrete. [ABSTRACT FROM AUTHOR]

This research aimed to identify changes in muscle mechanical properties (MMPs) when a standardized sequence of movements is performed and to determine the influence of acute low back pain (LBP) and age on the MMPs. Socio-demographic, clinical variables and MMPs were collected in 33 patients with LBP and 33 healthy controls. A 2 × 2 × 2 (group × age × time) analysis of variance (ANOVA) mixed model was used to determine the effect of the study factors on the different MMPs. There were no significant triple interactions. After the movements, tone and stiffness increased 0.37 Hz and 22.75 N/m, respectively, in subjects <35 years, independent of their clinical status. Relaxation showed differences by age in healthy subjects and creep in LBP subjects. Furthermore, elasticity was higher in <35 years (p < 0.001) without the influence of any other factor. In conclusion, sequenced movements can modify tone and stiffness as a function of age, while age-associated changes in viscoelastic characteristics depends on pain but not on movements. The MMPs should be assessed, not only at the beginning of the physical examination at rest, but also along the patient's follow-up, depending on their pain and age, in a clinical setting. [ABSTRACT FROM AUTHOR]

Flexible electronics sensors for tactile applications in multi-touch sensing and large scale manufacturing were designed and fabricated. The sensors are based on polyimide substrates, with thixotropy materials used to print organic resistances and a bump on the top polyimide layer. The gap between the bottom electrode layer and the resistance layer provides a buffer distance to reduce erroneous contact during large bending. Experimental results show that the top membrane with a bump protrusion and a resistance layer had a large deflection and a quick sensitive response. The bump and resistance layer provided a concentrated von Mises stress force and inertial force on the top membrane center. When the top membrane had no bump, it had a transient response delay time and took longer to reach steady-state. For printing thick structures of flexible electronics sensors, diffusion effects and dimensional shrinkages can be improved by using a paste material with a high viscosity. Linear algorithm matrixes with Gaussian elimination and control system scanning were used for multi-touch detection. Flexible electronics sensors were printed with a resistance thickness of about 32 μm and a bump thickness of about 0.2 mm. Feasibility studies show that printing technology is appropriate for large scale manufacturing, producing sensors at a low cost. [ABSTRACT FROM AUTHOR]

The rheological properties of fresh plaster mortars, with varied contents of porous fillers and polymer admixtures, have been studied. The quantities of fine limestone and expanded perlite, and dosages of methyl hydroxy ethyl cellulose and ethylene vinyl acetate were varied in the experiment. Effective viscosity (at a shear rate from 0.045 to 5.705 s−1) and the thixotropy of the mixes were determined with rotational viscometer for 18 compositions (according to the design of the experiment). Each of the 18 viscosity curves were described with the Ostwald–de-Waele equation. The Experimental–Statistical models describing the dependencies of the parameters of the rheological model and of mix thixotropy on the composition factors were built on the obtained data. ES-models have allowed the individual and synergetic effects of mix components on the rheological characteristics to be evaluated. The expanded perlite powder can increase the viscosity by two times, probably due to its pozzolanic effect increasing the content of the CSH phase during cement hydration. The thixotropy can be increased by the quantity of limestone. The computational experiments with ES-models have made it possible for the information set, without a noticeable interrelation between rheological characteristics, to be stratified into subsets, in which such interrelations differ significantly. [ABSTRACT FROM AUTHOR]