Search

Radiation techniques are used to modify the physical, chemical and biological properties of polymers. This induces crosslinking and degradation reactions of polymers by utilizing radicals generated through ionizing radiation. However, oxidation products (such as carbonyl) can be formed because oxidation occurs by chain scission in the presence of oxygen. Herein, we demonstrate the gamma-ray irradiation-induced oxidation with and without fluorine using polyethylene, polyvinylidene fluoride and polytetrafluoroethylene under the same conditions. In this study, changes in element-content and chemical-bond structures were analyzed before and after gamma-ray irradiation under air atmosphere. As a result, polytetrafluo-roethylene showed less oxidation and excellent thermal properties after the absorbed dose of 500 kGy. This can be attributed to the generation of stable perfluoroalkylperoxy radicals after gamma ray irradiation in the PTFE structure containing only CF2 groups, thereby hindering the oxidation reaction. [ABSTRACT FROM AUTHOR]

The outstanding electrical, mechanical, and thermal properties of carbon nanotubes (CNTs) make them promising materials for a wide range of applications. Numerous theoretical and experimental studies on the diameter-dependent properties of single-walled carbon nanotubes (SW-CNTs) exist. The incorporation of carbon nanotubes into commercial polymers can alter the properties of both materials. Herein, we demonstrate polystyrene/SW-CNT composites with different diameters to check property changes, including radiation-protective characteristics under various doses of gamma radiation. The intrinsic glassy state of polystyrene disappeared owing to the introduction of SW-CNTs into the polymer-polymer chain. In addition, when 1.3 nm diameter SW-CNTs were introduced, the Fourier-transform infrared spectroscopy peaks for alkyl aryl ethers were observed at 10–60 kGy of gamma irradiation. In this study, the different phenomena that occur when polystyrene/SW-CNT composites are formed with different SW-CNT diameters (0.78 nm and 1.3 nm) were investigated via systematic analyses. [ABSTRACT FROM AUTHOR]

The scission rates of polystyrene and fluorinated polystyrene irradiated in an irradiation facility with Co-60 γ-rays were determined using molecular dynamics simulation and gel permeation chromatography (GPC) molecular weight distributions. The prediction was based on the assumption that γ-ray energy is transferred to the initial velocity of the primary knock-on atom. We employed a molecular dynamics simulation procedure to compute the changes in bond length between the connections for selected values of the absorbed dose and compared the calculated values with measurements made on the irradiated samples. The samples were exposed to four different absorbed doses of 25, 50, 75, and 100 kGy. The scission process and scission ratio were simulated with LAMMPS with ReaxFF potential for each bond, and we compared the simulation results with the experimental data especially measuring average molecular weight to evaluate the effect of fluorination on radiation enhancement. [ABSTRACT FROM AUTHOR]

This paper describes a novel chromatographic method for efficient removal of anionic dyes from aqueous solutions. Chitosan-coated Fe3O4 nanoparticles can easily be immobilized on a dextran gel column. Single elution of Evans Blue (EB) solution to the nanoadsorbent-incorporated columns provides high removal efficiency with a maximum adsorption capacity of 243.9 mg/g. We also investigated the influence of initial concentration and solution pH on the removal efficiency of EB. The electrostatic interaction between the adsorbent surface and negatively charged sulfate groups on EB molecules promotes the efficient adsorption of dyes. The equilibrium data matched well with the Langmuir isotherm model, which indicated monolayer dye adsorption onto the adsorbent surface. To extend the application of the current method, we performed further adsorption experiments using other anionic dyes of different colors (Cy5.5, Acid Yellow 25, Acid Green 25, and Acid Red 1). All of these molecules can efficiently be captured under continuous flow conditions, with higher removal efficiency obtained with more negatively charged dyes. These findings clearly demonstrate that the present approach is a useful method for the removal of anionic dye contaminants in aqueous media by adsorption. [ABSTRACT FROM AUTHOR]

In this study, biodegradable poly(L-lactide-co-ε-caprolactone) (PLCL) and poly(L-co-d,l lactide) (PLDLA) were evaluated using Geant4 (G4EmStandardPhysics_option4) for damage simulation, in order to predict the safety of these biodegradable polymers against gamma ray sterilization. In the PLCL damage model, both chain scission and crosslinking reactions appear to occur at a radiation dose in the range 0-200 kGy, but the chain cleavage reaction is expected to be relatively dominant at high irradiation doses above 500 kGy. On the other hand, the PLDLA damage model predicted that the chain cleavage reaction would prevail at the total irradiation dose (25-500 kGy). To verify the simulation results, the physicochemical changes in the irradiated PLCL and PLDLA films were characterized by GPC (gel permeation chromatography), ATR-FTIR (attenuated total reflection Fourier transform infrared), and DSC (difference scanning calorimetry) analyses. The Geant4 simulation curve for the radiation-induced damage to the molecular weight was consistent with the experimentally obtained results. These results imply that the pre-simulation study can be useful for predicting the optimal irradiation dose and ensuring material safety, particularly for implanted biodegradable materials in radiation processing.