Search

This paper presents a low-profile reconfigurable antenna array capable of five radiation-pattern modes for vehicular communication applications. The antenna array consists of four antenna elements, each containing four square patches. Exciting one of the square patches generates a broadside radiation. A square parasitic patch is added at the rear of the excited patch, and two square parasitic patches are placed at the front. By optimizing the design of these parasitic patches, including the treatment of center slotting and addition of shorting pins, the antenna element achieves an end-fire beam with a certain tilt angle. On this basis, a reconfigurable feeding network is designed with 1:1 and 1:4 output modes. By connecting the reconfigurable feeding network to the four antenna elements and altering the on/off states of the PIN diodes in the feeding network, a reconfigurable antenna with four end-fire beams and one omnidirectional beam in its radiation pattern is realized. Measurement results demonstrate an excellent impedance bandwidth, radiation pattern, and gain performance in all modes. The four end-fire and one omnidirectional radiation characteristics make it highly suitable for vehicular communication applications. [ABSTRACT FROM AUTHOR]

Bandstop filters (BSFs) have many applications in suppressing interference signals and shielding specific bands. Among them, reconfigurable BSFs that cover more frequency bands by switching modes have great research value. In this paper, a novel synthesis approach for compact reconfigurable BSFs with controllable equal-ripple performance is proposed. By switching the ON/OFF state of the positive intrinsic negative (PIN) diode, the proposed reconfigurable BSF can be switched between single-BSF (S-BSF) and dual-BSF (D-BSF). Based on the synthesis approach, the equal-ripple levels of stopband and passband for S-BSF and D-BSF can be independently controlled. To verify, the equal-ripple levels of stopband and passband for S-BSF state and D-BSF state are independently controlled in four groups of examples. Finally, a reconfigurable BSF with a miniaturized size is designed and fabricated. The fabricated reconfigurable BSF behaves with 15 dB and 10 dB return loss (RL) in two different passbands of the D-BSF state, and 25 dB bandpass RL and controllable stopband rejection (SR) for the S-BSF state. The measured results are in good agreement with the electromagnetic (EM) simulation results. [ABSTRACT FROM AUTHOR]

This paper introduces an innovative and cost-effective approach for developing a millimeter-wave (mmWave) frequency-reconfigurable dielectric resonator antenna (DRA), which has not been reported before. The antenna integrates two rectangular DRA elements, where each DRA is centrally fed via a slot. A strategically positioned PIN diode is employed to exert control over performance by modulating the ON–OFF states of the diode, thereby simplifying the design process and reducing losses. In the OFF state, the first DRA, RDRA-I, exclusively supports the TE311 resonance mode at 24.3 GHz, offering a 2.66% impedance bandwidth and achieving a maximum broadside gain of 9.2 dBi. Conversely, in the ON state, RDRA-I and RDRA-II concurrently operate in the TE513 resonance mode at 29.3 GHz, providing a 2.7% impedance bandwidth and yielding a high gain of up to 11.8 dBi. Experimental results substantiate that the proposed antenna presents an attractive solution for applications necessitating frequency-reconfigurable and high-performance mmWave antennas in 5G and Beyond 5G (B5G) communication systems. [ABSTRACT FROM AUTHOR]

In this paper, a 3-bit circularly polarized reconfigurable reflectarray is proposed. The array consists of 64 units in an 8 × 8 configuration, with each unit containing a circular metal patch loaded with phase-delay lines and eight PIN diodes. To independently control each unit, a corresponding DC control circuit was designed and tested with the array. In the bandwidth of 3.43–3.71 GHz, the circularly polarized reconfigurable reflectarray achieved a gain of 16 dB, an aperture efficiency of 27%, an axial ratio of ≤3 dB, an operating bandwidth of 8%, and a beam scanning range of ±60°. The circularly polarized reconfigurable reflectarray can also achieve a good dual-beam radiation performance after testing. The 3-bit circularly polarized reconfigurable reflectarray proposed in this paper offers several advantages, including low loss, high aperture efficiency, a wide beam scanning range, and excellent stability in wide-angle oblique incidence. It has potential applications in low-cost phased array, satellite communications, and deep space exploration. [ABSTRACT FROM AUTHOR]

In this article, an ultra-wideband (UWB) antenna featuring two reconfigurable quasi-perfect stop bands at WLAN (5.25–5.75 GHz) and lower 5G (3.4–3.8 GHz) utilizing electromagnetic bandgaps (EBGs) and positive-intrinsic-negative (P-I-N) diodes is proposed. A pair of EBG structures are applied to generate sharp notch bands in the targeted frequency spectrum. Each EBG creates a traditional notch, while two regular notches are combined to make a quasi-perfect, sharp, notch band. Four P-I-N diodes are engraved into the EBG structures to enable notch band reconfigurability. By switching the operational condition of the four diodes, the UWB antenna can dynamically adjust its notching characteristics to enhance its adaptability to various communication standards and applications. The antenna can be reconfigured as a UWB (3–11.6 GHz) without any notch band, a UWB with a single sharp notch (either at WLAN or 5G), or a UWB with two quasi-perfect notch bands. Moreover, the antenna's notch bands can also be switched from a traditional notch to a quasi-perfect notch and vice versa. To confirm the validity of the simulated outcomes, the proposed reconfigurable UWB antenna is fabricated and measured. The experimental findings are aligned closely with simulation results, and the antenna offers notch band reconfigurability. The antenna shows a consistently favorable radiation pattern and gain. The dimension of the presented antenna is 20 × 27 × 1.52 mm3 (0.45 λc × 0.33 λc × 0.025 λc, where λc is the wavelength in free space). [ABSTRACT FROM AUTHOR]

Programmable metasurfaces are two-dimensional electromagnetic structures characterized by a low profile, conformability, and the ability to flexibly manipulate the amplitude and phase of electromagnetic waves. For high-quality beam scanning with the metasurface, it is essential that the metasurface possesses high-precision phase response quantization characteristics. This paper constructs a reflection-type metasurface unit cell featuring four P-I-N diodes and six operating states. To address the unit cell's complexity and optimization challenges, we developed an automatic optimization algorithm, derived from the genetic optimization algorithm, for the metasurface unit cell. This algorithm was used to optimize a six-phase reflective 2.5 bit programmable metasurface cell operating at 5 GHz. The unit cell's prototype was fabricated and measured to verify the design. Additionally, a metasurface comprising 16 × 16 unit cells was designed and simulated. The results highlight the metasurface unit cell's excellent phase response quantization characteristics, and investigate the impact of quantization accuracy on beam scanning. [ABSTRACT FROM AUTHOR]

Wireless communication systems have grown rapidly, moving towards being highly compact, intelligent, and flexible to adapt to changing operating requirements. Multifunctional and highly versatile antennas are key in this development to ensure system quality. Reconfigurable antennas, particularly regarding polarization, allow frequency reuse and enable the mitigation of fading effects. This work presents a square microstrip patch antenna operating in the ISM 5.8 GHz band with reconfigurable polarization by controlling its feeding. This antenna has four different states through the application of a symmetrical DC voltage that controls an RF circuit with PIN diodes. As a result, the microstrip patch can operate with three different polarizations: linear polarization and both circular polarizations (right-handed and left-handed). The antenna was fabricated to validate the proposed concept. The good agreement between the measurement and the simulation results was possible to observe regarding its polarization behaviour, impedance adaptation and radiation pattern. [ABSTRACT FROM AUTHOR]

A singly fed reconfigurable circular loop antenna is proposed for millimeter-wave (mmWave) communication systems. This antenna's distinctive feature lies in its capacity to adjust both polarization and bandwidth characteristics, a capability made possible by the strategic integration of two PIN diodes. These diodes are engineered to function in various modes, allowing for three distinct polarization states and accommodating two distinct bandwidths. A meticulous alignment of these PIN diodes enables the utilization of a single DC bias network as a highly effective RF choke, which simplifies the design and reduces the associated losses. Additionally, a planar biasing network that consists of coplanar strip-lines (CPS) has been employed eliminating the need for lumped elements. The simple and totally planar configuration offers a choice of right-hand circularly polarized (RHCP) radiation or left-hand circularly polarized (LHCP) radiation at 28 GHz. This is accompanied by impedance matching and axial ratio (AR) bandwidths of 12.9% and 8%, respectively, over the same frequency range with a gain of 7.5 dBic. Moreover, when the PIN diodes are unbiased, the antenna offers linear polarization (LP) over two narrow bandwidths at 27 GHz and 29 GHz featuring a maximum gain of 7.2 dBic. Therefore, the proposed configuration offers three operating modes: wide-band RHCP, wide-band-LHCP, and LP over dual narrow bands. Significantly, simulated results closely align with the measured outcomes, affirming the robustness and accuracy of this design. [ABSTRACT FROM AUTHOR]

The increasing prevalence of the Internet of Things (IoT) as the primary networking infrastructure in a future society, driven by a strong focus on sustainability and data, is noteworthy. A significant concern associated with the widespread use of Internet of Things (IoT) devices is the insufficient availability of viable strategies for effectively sustaining their power supply and ensuring their uninterrupted functionality. The ability of RF energy-harvesting systems to externally replenish batteries serves as a primary driver for the development of these technologies. To effectively mitigate concerns related to wireless technology, it is imperative to adhere strictly to the mandated limitations on electromagnetic field emissions. A TA broadband polarization-reconfigurable Y-shaped monopole antenna that is improved with a SADEA-tuned smart metasurface is one technique that has been proposed in order to accomplish this goal. A Y-shaped printed monopole antenna is first taken into consideration. To comprehend the process of polarization reconfigurability transitioning from linear to circular polarization (CP), a BAR 50-02 V RF PIN Diode is employed to shorten one of the parasitic conducting strips to the ground plane. A SADEA-driven metasurface, which utilizes the artificial intelligence-driven surrogate model-assisted differential evolution for antenna synthesis, is devised and positioned beneath the radiator to optimize performance trade-offs while increasing the antenna's gain and bandwidth. The ultimate prototype achieves the following: an impedance bandwidth of 2.58 GHz (3.27–5.85 GHz, 48.45%); an axial bandwidth of 1.25 GHz (4.19–5.44 GHz, 25.96%); a peak gain exceeding 8.45 dBic; and when a highly efficient rectifier is integrated, the maximum RF-DC conversion efficiency of 73.82% and DC output of 5.44 V are obtained. Based on the results mentioned earlier, it is considered appropriate to supply power to intelligent sensors and reduce reliance on batteries via RF energy-harvesting mechanisms implemented in hybrid wireless applications. [ABSTRACT FROM AUTHOR]

The optimization of the synthesis of III-V compounds is a crucial subject in enhancing the external quantum efficiency of blue LEDs, laser diodes, quantum-dot solar cells, and other devices. There are several challenges in growing high-quality InGaN materials, including the lattice mismatch between GaN and InGaN causing stress and piezoelectric polarization, the relatively high vapor pressure of InN compared to GaN, and the low level of incorporation of indium in InGaN materials. Furthermore, carrier delocalization, Shockley–Read–Hall recombination, auger recombination, and electron leakage in InGaN light-emitting diodes (LEDs) are the main contributors to efficiency droop. The synthesis of high-quality III-V compounds can be achieved by optimizing growth parameters such as temperature, V/III ratios, growth rate, and pressure. By reducing the ammonia flow from 200 sccm to 50 sccm, increasing the growth rate from 0.1 to 1 m/h, and lowering the growth pressure from 250 to 150 Torr, the external quantum efficiency of III-V compounds can be improved at growth temperatures ranging from 800 °C to 500 °C. It is crucial to optimize the growth conditions to achieve high-quality materials. In addition, novel approaches such as adopting a microrod crystal structure, utilizing the piezo-phototronic effect, and depositing AlN/Al2O3 on top of the P-GaN and the electron-blocking layer can also contribute to improving the external quantum efficiency. The deposition of a multifunctional ultrathin layers of AlN/Al2O3 on top of the P-GaN can enhance the peak external quantum efficiency of InGaN blue LEDs by 29%, while the piezo-phototronic effect induced by a tensile strain of 2.04% results in a 183% increase in the relative electroluminescence intensity of the LEDs. This paper also discusses conventional and inverted p-i-n junction structures of LEDs. [ABSTRACT FROM AUTHOR]

With the continuous advancement of technology, there is an increasing need for innovative solutions that can handle complex applications such as haptic communications, Internet of Things for smart cities, automation, and manufacturing. One technology that has received much attention is the phase reconfigurable metasurface for reconfigurable intelligent surfaces (RISs). The RIS demands low-power consumption, simple configuration, angular stability, and polarization insensitivity. The use of phase reconfigurable metasurfaces provides benefits such as low cost, low power consumption, and improved communication coverage and quality. This article introduces a reconfigurable combined-loop metasurface that can effectively manipulate phase reflection. This is achieved by incorporating four PIN diodes between two meta-atoms of a 2 × 2 periodic array within a single-layer metallic structure. By controlling the state of the PIN diodes, which can be switched into 16 different states, the metasurface can achieve various phase reflections. The proposed structure has validated a 32× 32 metasurface through numerical simulations and experiments that exhibit promising results, demonstrating its potential for use in 6G applications. [ABSTRACT FROM AUTHOR]

Recently, reconfigurable coding metasurfaces have attracted extensive attention due to their dynamic and flexible manipulation of electromagnetic (EM) waves, making them an effective solution to connect physical reality and information science. Nevertheless, most previously reported reconfigurable metasurfaces suffer from limited applications, as they solely possess either phase or amplitude modulation. In this article, we propose a reconfigurable coding metasurface that can regulate both phase and amplitude response independently. In the field of the metasurface, the phase response can tailor the wavefronts, and the amplitude response can adjust the redistribution of the energy of the EM waves. Specifically, by integrating a PIN diode into the meta-atom and controlling its bias voltage, the reflection phase can be switched between two opposite phases with a phase difference of about 180°, and the reflection amplitude can be manipulated from 0.02 to 0.98 continuously at 11 GHz. The unit element consists of simple multi-layer structures, reducing its production cost and processing difficulty. By loading 1-bit phase code and multi-bit amplitude code to each unit element severally, this metasurface can modulate the distribution of reflected EM waves in two-dimensional (2-D) space while simultaneously suppressing the sidelobes for any quantity of scattered beams over a wide operating band ranging from 10.5 to 11.5 GHz. This metasurface exhibits promising potential for manipulating the distribution of EM wave energy and shaping of EM beams, which can be expected to facilitate wireless communication technology. [ABSTRACT FROM AUTHOR]

In this paper, a low-cost resin-coated commercial-photo-paper substrate is used to design a printed reconfigurable multiband antenna. The two PIN diodes are used mainly to redistribute the surface current that provides reconfigurable properties to the proposed antenna. The antenna size of 40 mm × 40 mm × 0.44 mm with a partial ground, covers wireless and mobile bands ranging from 1.91 GHz to 6.75 GHz. The parametric analysis is performed to achieve optimized design parameters of the antenna. The U-shaped and C-shaped emitters are meant to function at 2.4 GHz and 5.9 GHz, respectively, while the primary emitter is designed to operate at 3.5 GHz. The proposed antenna achieved peak gain and radiation efficiency of 3.4 dBi and 90%, respectively. Simulated and measured results of the reflection coefficient, radiation pattern, gain, and efficiency show that the antenna design is in favorable agreement. Since the proposed antenna achieved wideband (1.91–6.75 GHz) using PIN diode configuration, using this technique the need for numerous electronic components to provide multiband frequency is avoided. [ABSTRACT FROM AUTHOR]

This paper presents a compact multifrequency reconfigurable patch antenna in terms of design and fabrication for operating in the S and C bands of the RF spectrum, which are overwhelmed by wireless applications. Reconfiguration is achieved by using a single PIN diode on the ground plane. By varying the voltage applied to the diode, three modes can emerge, exhibiting main resonant frequencies at 2.07, 4.63, and 6.22 GHz. Resonance switching requires a voltage of less than 0.9 V. The antenna fabricated on an FR-4 substrate, with a volume of 70 × 60 × 1.5 mm3, has a radiating patch element of a rectangular ring shape. The proposed low-cost antenna is easily implemented in a typical university lab-based environment. The total bandwidth for the three modes is close to 1 GHz, while the voltage standing wave ratio (VSWR) of the fabricated version of the antenna does not exceed 1.02, and the return loss is well below −40 dB for the three primary resonant frequencies. [ABSTRACT FROM AUTHOR]

In this paper, we propose a reconfigurable intelligent surface (RIS) that can dynamically switch the transmission and reflection phase of incident electromagnetic waves in real time to realize the dual-beam or quad-beam and convert the polarization of the transmitted beam. Such surfaces can redirect a wireless signal at will to establish robust connectivity when the designated line-of-sight channel is disturbed, thereby enhancing the performance of wireless communication systems by creating an intelligent radio environment. When integrated with a sensing element, they are integral to performing joint detection and communication functions in future wireless sensor networks. In this work, we first analyze the scattering performance of a reconfigurable unit element and then design a RIS. The dynamic field scattering manipulation capability of the RIS is validated by full-wave electromagnetic simulations to realize six different functions. The scattering characteristics of the proposed unit element, which incorporates two p-i-n diodes have been substantiated through practical implementation. This involved the construction of a simple prototype and the subsequent examination of its scattering properties via the free-space measurement method. The obtained transmission and reflection coefficients from the measurements are in agreement with the anticipated outcomes from simulations. [ABSTRACT FROM AUTHOR]

In this research, a novel unit-cell design for a 2-bit reflective metasurface using the theory of characteristic modes is presented. The initial unit-cell consists of three sub-patches with 2-PIN diodes integrated within the gaps between sub-patches. The initial structure provides limited tuning of the phase curves with the change in switching states of PIN diodes. To provide the phase deviation required for the 2-bit operation, the symmetry of the modal currents is used to propose multiple slots in the sub-patches. Slots are introduced to lower the resonant frequencies, as well as provide tuning of the resonance of modes and consequently phase change between different switching states. For further resonance tuning and phase optimization, two vias are loaded in the middle patch to provide a 90° phase difference between each switching state. Simulated results show that the proposed unit-cell design with the aid of characteristic modes has a smaller size and provides 2-bit operation in the frequency range of 3.9–4.04 GHz. [ABSTRACT FROM AUTHOR]

This study introduces innovative designs for frequency-reconfigurable antennas that utilize ring resonators combined with either PIN diodes or RF switches. These designs enhance the versatility, adaptability, and overall performance of the antennas in wireless communication systems. By controlling the switches and ring resonator, the antenna's resonant frequencies and bandwidths can be adjusted, allowing for compatibility with various communication standards and frequency ranges. The proposed antenna exhibits four distinct operational states, each characterized by different resonance frequencies and operating frequency bands. Return loss, radiation pattern, radiation efficiency, and surface current distribution are analyzed for each state. State-1 (ON-ON) and State-2 (OFF-ON), which are characterized by resonance frequencies of 2.4 GHz and 3.33 GHz respectively, offer ranges suitable for Wi-Fi, Bluetooth, ISM, and IoT applications. State-3 (ON-OFF), with a resonance frequency of 3.0 GHz and bandwidth spanning from 2.59 GHz to 3.643 GHz, complies with Wi-Fi, Wi-Fi 6, and IoT requirements. State-4 (OFF-OFF) covers the band centered around 3.45 GHz. It is compatible with many applications such as 5G mid-band, Wi-Fi 6E, IoT, and cellular systems. The proposed antenna designs are versatile and compact since the overall antenna dimensions are 25 × 18 × 1.6 mm3. The radiation efficiency of the antenna configuration varies depending on operational states. By utilizing the advantages of both ring resonators and RF switches, the proposed antenna configurations offer new solutions that enhance their performance in wireless communication systems. This study compares the effects of using PIN diodes and SPDT switches on the performance of antennas and also examines the DC biasing effect on antenna characteristics. The simulation results are validated by the experimental analysis. The proposed antenna designs offer a new approach for wireless communication systems by using both ring resonators and RF switches. [ABSTRACT FROM AUTHOR]

This paper proposes a switchable polarization-insensitive frequency selective rasorber (FSR) within the X-band. The FSR comprises a lossy layer, a lossless layer, and an intermediate air layer. The lossy layer consists of metal patches, folded wires, and lumped resistors, while the lossless layer is formed with square and cross patches loaded with PIN diodes. An equivalent circuit model (ECM) has been developed to analyze and verify the working principle of the system. By altering the state of the PIN diodes, it is feasible to switch between absorbing and transmitting modes. In the rasorber mode, the switchable FSR attains a transmission window ranging from 10.13 to 12.27 G H z with a minimum insertion loss below 2 d B and a broad absorption band covering 5.79–15.37 G H z . When switched to absorber mode, the passband is negated, and the FSR exhibits a low transmission band from 10.68 to 18.00 G H z . This innovation can improve the omni-directional stealth capability and battlefield survivability of radar systems, possessing substantial research importance and practical applications. [ABSTRACT FROM AUTHOR]

In this work, an electronically reconfigurable dual-band dual-mode microstrip ring antenna with high isolation is proposed. Using characteristic mode analysis (CMA), the physical characteristics of the ring antenna are revealed, and two modes are appropriately chosen for operation in two sub-6 GHz "legacy" bands. Due to the inherent orthogonality of the characteristic modes, measured isolation larger than 37 dB was achieved in both bands without requiring complicated decoupling approaches. An integrated electronically reconfigurable matching network (comprising PIN diodes and varactors) was designed to switch between the two modes of operation. The simulated and measured results were in excellent agreement, showing a peak gain of 4.7 dB for both modes and radiation efficiency values of 44.3 % and 64 % , respectively. Using CMA to gain physical insights into the radiative orthogonal modes of under-researched and non-conventional antennas (e.g., antennas of arbitrary shapes) opens the door to developing highly compact radiators, which enable next-generation communication systems. [ABSTRACT FROM AUTHOR]

This article introduces a process to design, simulate, and measure a novel multi-band patch antenna with different operation modes, i.e., band centers and bandwidths. Switching between operation modes is possible using a pair of PIN diodes to connect different parts of the antenna with the main antenna patch. Such a reconfigurable design allows for individual control of each frequency range. The main operation mode of the resulting antenna has an impedance bandwidth with two bands, one from 2.4 GHz to 2.73 GHz and another from 3.4 GHz to 5.73 GHz, with a maximum gain of 4.85 dBi and stable radiation patterns. The resulting antenna is suitable for applications using both ultra-wideband technologies and wireless local-area network (WLAN) technologies. [ABSTRACT FROM AUTHOR]

In this paper, we proposed a multibeam switching antenna based on a low-cost reconfigurable hybrid metasurface applied for beamforming systems. The antenna consists of two parts: a microstrip feed antenna and a transmission hybrid metasurface. The latter is composed of three types of units with different amplitude and phase responses to electromagnetic waves so as to control the beams of the feed antenna. Sixteen PIN diodes are arranged in the metasurface with a simple bias network. When two different direct-current voltages are applied to the PIN diodes, the antenna can dynamically switch between two beams and four beams. For demonstration, the proposed antenna is fabricated, and the measured results show that the antenna operates at 9.07–9.42 GHz (−10 dB bandwidth) with a total size of 1.80λ0 × 1.52λ0 × 0.22λ0 (λ0 corresponds to the wavelength of 9.28 GHz in free space). With the merits of a compact structure, low cost and good radiation performance, the proposed design is suitable for beamforming applications. [ABSTRACT FROM AUTHOR]

This paper presents a novel frequency reconfigurable antenna design for sub-6 GHz applications, featuring a unique combination of antenna elements and control mechanisms. The antenna is composed of an outer split-ring resonator loaded with an inner spiral resonator, which can be adjusted through the remote control of PIN diode or Single Pole Double Throw (SPDT) switches. The compact antenna, measuring 22 × 16 × 1.6 mm3, operates in broadband, or tri-band mode depending on the ON/OFF states of switches. The frequency reconfigurability is achieved using two BAR64−02V PIN diodes or two CG2415M6 SPDT switches acting as RF switches. SPDT switches are controlled remotely via Arduino unit. Additionally, the antenna demonstrates an omni-directional radiation pattern, making it suitable for wireless communication systems. Experimental results on an FR-4 substrate validate the numerical calculations, confirming the antenna's performance and superiority over existing alternatives in terms of compactness, wide operating frequency range, and cost-effectiveness. The proposed design holds significant potential for applications in Wi-Fi (IEEE 802.11 a/n/ac), Bluetooth (5 GHz), ISM (5 GHz), 3G (UMTS), 4G (LTE), wireless backhaul (4G and 5G networks), WLAN (IEEE 802.11 a/n/ac/ax), 5G NR n1 band, and Wi-Fi access points due to its small size and easy control mechanism. The antenna can be integrated into various devices, including access points, gateways, smartphones, and IoT kits. This novel frequency reconfigurable antenna design presents a valuable contribution to the field, paving the way for further advancements in wireless communication systems. [ABSTRACT FROM AUTHOR]

In this paper, we propose a new filtering switch with excellent working performance made using an optimized coupled microstrip line. Upon analyzing the RF (radio frequency) front-end's system structure, the switching device was simplified to a diode, which was connected to the microstrip circuit we designed to become a filter switch with both filtering and shutdown functions. First, we obtained an equivalent schematic of this filtering switch based on the relevant microstrip line theory. This switch consists of two coupled microstrip circuits, parallel-coupled feed lines and coupled-line stub-load resonators (CLSs), and a PIN diode. Second, the operating principle is described by the switching of the operating states, with ideal shutdown performance in the off state and considerable selectivity and excellent out-of-band rejection performance in the filtered state. Finally, a prototype filtering switch with a center frequency of 0.8 GHz was designed and tested. After subsequent optimization and improvement, the simulation and test performance results were noticeably consistent, consequently verifying the performance requirements of this filtering switch in two operating states in the center frequency band. [ABSTRACT FROM AUTHOR]

In this paper, we present a study on a broadband transparent tapered slot antenna. In general, the objective of achieving optical transparency is to enable antennas to seamlessly integrate into windows, offering an aesthetically pleasing and inconspicuous appearance. The aim of our research is to develop antennas that possess the ability to adjust horizontal plane beams across a wide frequency range, from 24 to 28 GHz, for 5G applications. This structure combines three antennas into a single unit, providing an advantage in terms of saving space. Furthermore, this structure offers the possibility of choosing between using a single antenna to obtain a directional beam in the −90°, 0°, or +90° directions (depending on the activated antenna) corresponding to three states, or the combination between two states to obtain another three additional states. The combination of the three states also allows for the acquisition of another state. At this point, the total number of states is 23 − 1. Only three PIN diodes are employed to switch between all states. Additionally, by adjusting the bias values of the PIN diodes, which function as variable resistors, the antenna beamwidth can be adjusted in order to achieve a coverage of 300°, offering more radiation pattern reconfigurability. The proposed method offers several advantages, including simplicity and feasibility in controlling the beamwidth and the beam direction electronically. This structure can be easily integrated into the development of fifth-generation communication systems. [ABSTRACT FROM AUTHOR]

To overcome the limitations of traditional frequency selective surfaces in flexible state switching at the same frequency, this paper proposes a novel active frequency selective surface (AFSS) that simultaneously exhibits conversion between absorption and transmission modes at the same frequency band. By welding PIN diodes on the bottom structure of the AFSS, the conversion between band-pass (transmission) and band-stop (absorption) filters can be controlled electronically. In the common-frequency switch between absorption and transmission modes, the impedance matching of the AFSS is attained by altering the capacitance value of the varactors embedded on the top structure of the AFSS. The functionalities of the proposed AFSS design are investigated by full-wave simulations (in HFSS software) at 11.4 GHz. Furthermore, the operating principle is analyzed using an equivalent circuit model (in AWR software). To verify the concept, a prototype is manufactured, and the responses of mode switching are measured by adjusting the bias voltage. The measurement result is consistent with the simulation analysis. Owing to the tunability of the varactors, the structural asymmetry is compensated to achieve 80% absorptivity and transmissivity within a field of view of ±35°. The developed AFSS structure is highly valuable to be used in scenarios such as antenna domes, etc. [ABSTRACT FROM AUTHOR]

In this study, a novel reconfigurable triple-band monopole antenna for LoRa IoT applications is fabricated on an FR-4 substrate. The proposed antenna is designed to function at three distinct LoRa frequency bands: 433 MHz, 868 MHz, and 915 MHz covering the LoRa bands in Europe, America, and Asia. The antenna is reconfigurable by using a PIN diode switching mechanism, which allows for the selection of the desired operating frequency band based on the state of the diodes. The antenna is designed using CST MWS® software 2019 and optimized for maximum gain, good radiation pattern and efficiency. The antenna with a total dimension of 80 mm × 50 mm × 0.6 mm (0.12 λ 0 × 0.07 λ 0 × 0.001 λ 0 at 433 MHz) has a gain of 2 dBi, 1.9 dBi, and 1.9 dBi at 433 MHz, 868 MHz, and 915 MHz, respectively, with an omnidirectional H-plane radiation pattern and a radiation efficiency above 90% across the three frequency bands. The fabrication and measurement of the antenna have been carried out, and the results of simulation and measurements are compared. The agreement among the simulation and measurement results confirms the design's accuracy and the antenna's suitability for LoRa IoT applications, particularly in providing a compact, flexible, and energy efficient communication solution for different LoRa frequency bands. [ABSTRACT FROM AUTHOR]

In this manuscript, a reconfigurable leaky wave antenna is proposed with linearly polarized and circularly polarized properties, which is composed of two layers with feeding waveguide and radiation elements. The bottom layer is a half-mode substrate integrated waveguide etched with a spoof surface plasmon polaritons structure as a high-dispersion feeding waveguide to excite 8 circular patches as radiation elements in the top layer. In a unit element, the horizontal linear polarization (HLP) and right-hand circular polarization (RHCP) radiation are switched using a p-i-n diode crossing a slot of a circular metal patch. HLP performance is achieved as the p-i-n diode is switched off, and RHCP is achieved as the p-i-n diode is switched on. The measured results verify the design theory and the simulated results. Over the working band of 10.4~12.8 GHz, the proposed antenna can radiate scanning beams covering about a 73° region, including the broadside direction with HLP and RHCP. [ABSTRACT FROM AUTHOR]

In this work, a novel electrically reconfigurable phase shifter based on a half-mode substrate integrated waveguide (HM-SIW) is proposed. SIW is a guided transmission line topology, and by using half-mode excitation, a smaller size can be achieved. Phase shifters are electronic devices that change the phase of transmission for a wide range of applications, including inverse scattering and sensing. The tunability of PIN diodes is applied here to achieve a reconfigurable design. The proposed single-layer structure does not require extra wiring layers for the bias circuit on the suggested printed circuit board. Its principle consists in the integration, in the HM-SIW, of three parallel lines, each connecting the edge of the HM-SIW and linked to a PIN diode and a radial stub. Here we present the results of measurements for a frequency band from 4.5 to 7 GHz that demonstrate how the experiment agrees with simulations. Insertion loss was less than −10 dB, and port coupling was less than −2 dB for both simulation and measurement solutions. The proposed half-mode structure is around half the size of a typical SIW line. With the proposed design, the seven states of the PIN diodes can be validated (ON and OFF), with a wide band adaptation and a relatively constant phase difference across a broad frequency range (44%). A key benefit of the proposed design for a microwave component is the reduction of extra biasing layers for the PIN diodes. This is in addition to the reduced size of the transmission line compared to a commercial SIW. In the annexed section, simulation software is used for a more comprehensive analysis involving more phase shift values and parametric studies. [ABSTRACT FROM AUTHOR]

Multi-bit phase shifters are typically implemented by cascading multiple phase-shifting units, therefore incurring large dimensions and higher insertion losses. This paper presents highly compact single-unit two-bit reflection-type phase shifters (SUTBRTPSs), with large phase shifts range and lower insertion loss by using only one 3-dB hybrid coupler, unlike traditional multi-bit reflection-type phase shifters. To achieve this, two identical dual-voltage controlled reactance blocks (DVCRBs) are loaded to the 3-dB hybrid directional coupler at through and coupled ports, and 04 states of phase shifts are obtained between the input and isolated ports. Each DVCRB consists of 03 open-circuited transmission lines and switching p-i-n diodes and provides half of the required susceptance to achieve the desired phase shifts. Design theory is presented in detail, and for validation and demonstration, two typical SUTBRTPSs (0°/45°/90°/135° and 0°/22.5°/180°/202.5°) are designed, fabricated and measured. Being implemented in a single-unit structure, the proposed method yields highly compact dimensions of 0.44 λg × 0.46 λg and 0.54 λg × 0.46 λg, respectively. The simulation and measurements results are in good agreement and indicate maximum insertion losses of 1.7 and 2.1 dB with a return loss better than 20 dB and phase error of less than 1.5°. [ABSTRACT FROM AUTHOR]

Tunable/switchable devices are more and more required in modern communication systems. However, the realization of the tuning requires the presence of active devices, which in turn must be biased. The current paper comes up with a solution for designing and experimentally validating such a switchable Frequency Selective Surface. Two different metallic structures are simulated and measured, having incorporated the same topology control network (CN). In this scenario, the main innovation of this paper is the presence of the feeding part, namely the control network. In this work, the main FSS structure is flanked by three parallel CN microstrip lines and several via holes that allow biasing the active elements, namely PIN diodes. The switchability of the proposed structure is achieved through PIN diodes, whose bias determines the values of the elements in the equivalent circuit. At different biases, the response of the FSS changes accordingly. From all possible values of the bias, the extreme cases when the diodes act as (almost) short- and open-circuits are considered in the submitted manuscript for the sake of brevity. These cases are modeled by the main and cut-slot structures, respectively. The proposed structures have been evaluated using electromagnetic simulation and implemented on an FR4 substrate having a thickness of 1.58 mm. With the periodicity of the square-shaped unit cell of 18 mm edge length, different filtering bands are obtained below 12 GHz. Another novelty that has received very little consideration in the existing literature is the use of a finite array of unit cells instead of an infinite one. And finally, tests in an anechoic chamber have proved that there is a good agreement between practical and simulation results and also demonstrated the proper performance of the devices for wide angular incidence for both TE and TM polarizations. [ABSTRACT FROM AUTHOR]

This paper presents an effective way to design an RFID tag antenna to operate at three different frequencies by incorporating a switching technique. PIN diode has been used to switch the RF frequency because of its good efficiency and simplicity. The conventional dipole-based RFID tag has been improvised with added co-planar ground and PIN diode. The layout of the antenna is designed with a size of 0.083 λ 0 × 0.094 λ 0 at UHF (80–960) MHz, where λ 0 is the free-space wavelength corresponding to the mid-point of the targeted UHF range. The RFID microchip is connected to the modified ground and dipole structures. Bending and meandering techniques on the dipole length help to match the complex chip impedance with the dipole impedance. Additionally, it scales down the total structure of the antenna. Two PIN diodes are placed along the dipole length at appropriate distances with proper biasing. The ON-OFF switching states of the PIN diodes enable the RFID tag antenna to switch over the frequency ranges (840–845) MHz (India), 902–928 MHz (North America), and 950–955 MHz (Japan). [ABSTRACT FROM AUTHOR]

As the same device may be used for various types of applications, antennas must have the capacity to perform multiple functions. Reconfiguring the polarization, operational frequency, and radiation pattern can create an outcome of multi-functionality. A hybrid, frequency- and pattern-reconfigurable antenna with two V-shaped extrudes in a patch is proposed. To increase the bandwidth of the proposed antenna, the defected ground structure (DGS) phenomenon is presented, which is significant in the bandwidth of 3200 MHz from 2.7 GHz to 5.9 GHz, providing a gain of 3.5 dB. For this design, an FR-4 material was chosen as the substrate, and CST software was used for simulation. Using two p-i-n diodes, the projected antenna illustrates switching for multi-frequency bands such as 1.5, 2.6, 3.2, 5.1, and 8.1 GHz, with a constant radiation pattern and a main lobe direction of 155 degrees. It has C-band, WLAN, cognitive radio (CR), and Bluetooth applications. The proposed antenna displays radiation pattern switching at 3.5 GHz, showing variation between 7°, 158°, 173°, and 175°, and at 4 GHz, it demonstrates switching between 11°, 15°, 165°, and 344°, which defines the hybrid reconfiguration. [ABSTRACT FROM AUTHOR]

Embracing the era of higher operating frequencies, expanding functionality, and increased integration scale, modern circuit design relies more and more on the accurate prediction of the electromagnetic (EM) effects resulting from undesired radiation and mutual coupling of digital electronic devices. In this paper, an electromagnetic-physics-based simulation method is proposed, to simulate semiconductor devices and circuits. It utilizes physics-based simulation to analyze semiconductor devices in a circuit and incorporates this physics-based simulation into electromagnetic simulation (e.g., the finite difference time domain (FDTD)), to simulate a circuit at high frequency. To validate the proposed method, sample numerical results on circuits containing a commercial p-i-n diode with model number mot_bal99lt1 at radio frequency (RF) were obtained and compared with measurement data. The comparison showed a good agreement between the two sets of data, which validated the feasibility and accuracy of the proposed algorithm. Moreover, the proposed method can provide a useful physical mechanism for understanding effects on semiconductor devices and circuits. [ABSTRACT FROM AUTHOR]

In this work, a spectrum-sensing monopole antenna was used to operate in different frequency bands for cognitive radio applications. The proposed antenna consists of a folded monopole antenna with a partial ground plane, and it can be used for various wireless technologies operated at various frequencies from 1.5 to 3.5 GHz. The suggested antenna was printed on a RO4003 substrate with 3.38 permittivity and an overall size of 60 × 60 × 0.813 mm3. To achieve reconfigurability of the antenna, PIN diodes (HPND-4005) were inserted at different lengths along the antenna to obtain the desired performance. The antenna was fabricated and experimentally tested to validate the simulation outcomes, and distinct consistency between the simulation and measurement outcomes was obtained. Computer simulation tool (CST) software was used to design and simulate the suggested antenna and then the model was fabricated to validate the simulation outcomes. [ABSTRACT FROM AUTHOR]

In this paper, a frequency reconfigurable multiband multiple-input-multiple-output (MIMO) antenna is developed for 5G communication systems. The presented MIMO antenna element consists of a 50 Ω microstrip line, a rectangular monopole divided into two patches, and a partial ground plane. A split-ring resonator (SRR) is introduced into the upper patch to cover multiple 5G application bands, and an RF PIN diode is embedded between the upper and lower patches to enable the frequency diversity feature. In order to design a MIMO antenna with improved inter-element isolation, four antenna elements are orthogonally located with ground planes connected to each other. The antenna design covers the n41/n46/n48/n79 5G application bands. The prototype MIMO antenna is developed on the FR-4 substrate, and the measured results match with the simulated outcomes. The overall footprint of the prototype antenna is 70 × 70 × 1.6 mm3. [ABSTRACT FROM AUTHOR]

In this paper, a switchable filter based on the microstrip line (ML) with reflectionless-bandpass-to-reflectionless-bandstop responses is designed, theoretically validated, and fabricated. This single-port reflectionless bandpass filter (R-BPF) consists of a BPF and a shunt-connected bandstop section with terminated absorption resistors. The single-port reflectionless bandstop filter (R-BSF) is made of a BSF and a parallel bandpass circuit with terminated absorption resistors. These two reflectionless operational modes, namely R-BPF and R-BSF, are allowed to reconfigure the multifunctional filtering device using PIN diodes. In addition, a theoretical analysis of terminal impedance is performed to illustrate the working mechanism of the reflectionless response. To demonstrate the application of the proposed designs, a prototype of the switchable filter for R-BPF to R-BSF responses is fabricated and measured. For the R-BPF mode, the 3-dB fractional bandwidth (FBW) is 36.75% (1.67–2.42 GHz) with a 10-dB reflectionless bandwidth (RBW) of 1.36–2.58 GHz (i.e., FBW of 61.9%). For the R-BSF mode, the 10-dB bandwidth is 13% (1.85–2.11 GHz) with a 10.7-dB RBW of 1–3 GHz (i.e., FBW of 100%). An acceptable agreement between the measured and simulated results has been achieved. [ABSTRACT FROM AUTHOR]

Beamwidth-reconfigurable antennas are useful for the intersatellite link of low earth orbit formation flying and constellation, as they prevent unauthorized satellites from eavesdropping. In this article, a circularly polarized slot array antenna based on a half-mode substrate-integrated waveguide (HMSIW) for the K-band beamwidth reconfiguration is proposed using a new radio frequency (RF) switch structure and a pair of modified −45° and +45° linearly polarized HMSIW slot arrays for the dual operation of a single-pole double-throw (SPDT)/a power divider (PD) and easy integration with other components, respectively. The RF switch structure consists of a T-junction PD, λ/4 lines, and beam lead PIN diodes with current control resistors and without a DC block circuit for low DC power consumption and size reduction. The −45°/+45° linearly polarized HMSIW slot arrays providing linear and circular polarizations (LP and CP, respectively) are operated for CP. The use of a short-circuited termination instead of dissipative termination results in easier integration with other components because the 16 radiating slots consume most of the input power. The dimension of the beamwidth-reconfigurable antenna including the bottom metal layer is 157.2 × 23.3 × 0.254 mm3 (12.5λ0 × 1.86λ0 × 0.0202λ0). The RF switch for the SPDT shows the insertion losses of 1.8–2.3 and 16.7–24.2 dB and an isolation of 20.9–33.4 dB for both outputs within the 10-dB bandwidth. The RF switch for the PD has an insertion loss of 3.9–4.8 dB. The one- and two-antenna operation modes of the CP antenna provide the gains of 9.44 and 6.99 dBic, the axial ratios of 2.24 and 3.47 dB, and the horizontal beamwidths of 35.8° and 78.2°, respectively. [ABSTRACT FROM AUTHOR]

Silicon carbide (SiC), thanks to its material properties similar to diamond and its industrial maturity close to silicon, represents an ideal candidate for several harsh-environment sensing applications, where sensors must withstand high particle irradiation and/or high operational temperatures. In this study, to explore the radiation tolerance of SiC sensors to multiple damaging processes, both at room and high temperature, we used the Ion Microprobe Chamber installed at the Ruđer Bošković Institute (Zagreb, Croatia), which made it possible to expose small areas within the same device to different ion beams, thus evaluating and comparing effects within a single device. The sensors tested, developed jointly by STLab and SenSiC, are PIN diodes with ultrathin free-standing membranes, realized by means of a recently developed doping-selective electrochemical etching. In this work, we report on the changes of the charge transport properties, specifically in terms of the charge collection efficiency (CCE), with respect to multiple localized proton irradiations, performed at both room temperature (RT) and 500 °C. [ABSTRACT FROM AUTHOR]

This paper presents a compact coaxial-fed square microstrip patch antenna integrated with a beam-steering Partially Reflective Surface (PRS). The proposed design has a two-dimensional (2-D) Fabry-Perot Cavity (FPC) antenna acting as a radiator and the PRS as a beam-steering superstrate operating at 5.5 GHz. The PRS consists of 6 × 6 reconfigurable unit cells etched on Rogers 5880 with a thickness of 1.57 mm. By controlling the switching of PIN diodes in different sections of PRS, beam steering can be achieved up to ±47° in the azimuth plane with a gain of 9.1 dB and 10.2 dB and ± 15° steering in an elevation plane with a measured gain of 9.3 dB and 8.9 dB, respectively. The antenna prototype is 2.56 λ × 2.56 λ at 5.5 GHz, and the measured gain values are around 10 dBi for all the states. The beam is able to radiate at boresight or tilted to 42° in two azimuthal directions and 45° in elevation direction by adjusting the PIN diodes ON/OFF states. The 10 dB impedance bandwidth of 5.4–5.52 GHz is achieved. [ABSTRACT FROM AUTHOR]

This work presents a bandpass-reconfigurable planar pseudohairpin filter based on RF-MEMS switches. Hairpin-line structures are preferred to design microstrip filters because this class of filters offers a more compact size, and, in general, hairpin filters do not need ground connections for resonators. In this work, the U-shape resonators are arranged to obtain an interdigit capacitor to improve the coupling between the resonators. RF-MEMS switches modify the lengths of coupled resonators by adding microstrip segments to control the filter bandwidth, moving the center frequency and the return loss. An experimental hairpin tunable filter prototype based on RF-MEMS has been designed, fabricated, numerically and experimentally assessed, and compared concerning its tunability, quality factor, and capability with standard tunable filters based on PIN diodes. In conclusion, the tunable hairpin filter based on RF-MEMS switches offers the best performance in center frequency tuning range, compactness, and power consumption regarding reconfigurable filters based on standard PIN diodes switches. The obtained results are appealing and demonstrate the capabilities and potentialities of RF-MEMS to operate with the new communication standards that work at high microwave frequency bands. [ABSTRACT FROM AUTHOR]

In this paper, we propose a reconfigurable metadevice with independent polarization control based on a 90° rotationally symmetric microstructure. Three functionalities of broadband high-efficiency transmission, broadband high-efficiency reflection, and perfect absorption are switched by the on-state and off-state PIN diodes. Coding metadevices designed with diversified lumped element combinations are further studied in detail. By controlling the two diodes on the top layer in opposite states, absorption bandwidth is significantly improved. Reasonable arrangements of coding sequences allow for reflected dual/multi-beam modulation. Electric field distribution, power loss, complex impedance functions, and equivalent circuit models are used to better analyze the physical mechanism of the design. A prototype of the microstructure has been fabricated, and the experimental results agree well with the simulation. Electronic components integrated microstructures with high degrees of freedom have potential applications in intelligent wireless communication, electronic detection, advanced sensors, and smart stealth radomes. [ABSTRACT FROM AUTHOR]

Featured Application: The proposed metasurface in the article can be used in millimeter wave sensing and 5G wireless communications. A programmable coding metasurface provides unprecedented flexibility to manipulate electromagnetic waves dynamically. By controlling the peculiarity of subwavelength artificial atoms, devices with metasurfaces perform various functionalities. In this paper, a compact programmable coding metasurface with PIN diodes is proposed to realize the beam steering in the Ka band. The phase distribution on the metasurface can be actively controlled by switching the states of each meta-atom. By tuning the phase gradient along the metasurface plane, the reflective beam can scan all directions in the upper half-plane. In addition, the compact metasurface is easier to integrate, which could expand the fields of applications. The full-wave simulation results show that the radiation direction of the main lobe is consistent with the theoretical calculation results, and the maximum steering angle of simulation is 60°. As experimental verification, a prototype was processed and the functionality of beam steering in the xoz plane and in the yoz plane was tested. Experimental results show that the designed metasurface can achieve beam steering in both planes, and the maximum scan angle is 45° in the xoz plane. The proposed metasurface opens a new way of beam steering in half space, which may have potential applications in sensing and wireless communications in millimeter waves. [ABSTRACT FROM AUTHOR]

This paper presents two novel on-chip bandstop to bandpass reconfigurable filters in C and X bands. Designed on a silicon substrate, filter reconfigurability is achieved using semiconductor-distributed doped areas (ScDDAs), such as an N+PP+ junction integrated into the substrate. The active element is therefore co-designed with the passive parts, allowing flexibility in ScDDA size and position. This flexibility offers advantages in terms of integration, ease of manufacture, and performance. The synthesis was developed in the OFF-state in order to match with the well-known one in the ON-state. As proof of concept, 5 GHz and 10 GHz filters were built. The simulated and measured results showed good agreement in both bandpass and bandstop configurations. [ABSTRACT FROM AUTHOR]

This study presents a unique frequency-reconfigurable antenna that may be the first to use a dip switch and a bias circuit integrated on the same substrate as the antenna. Such an antenna may be used for many wireless applications, since it is small and versatile enough to operate in several frequency bands with different modes. Printed on a Rogers RT5880 substrate, the suggested structure has a relative permittivity of 2.2, a tangent loss of 0.0009, and a size of 28 × 26.35 × 1.6 mm3. Three-PIN diode switches are inserted between radiating patches. The proposed antenna operates in four modes, covering nine different bands by using three dual bands (i.e., 4.36 and 7.78 GHz, 3.56 and 6.89 GHz, 3 and 6.2 GHz) in MODE 1, MODE 2, and MODE three, respectively, and triple band in MODE 4 (i.e., 2.88, 5.87, and 8.17 GHz). The efficiency of the planned antenna is 97.66%, and the gain varies from 1.38 to 4.89 dBi. The obtained bandwidths at corresponding frequencies range from 5.5 to 31.17%. The suggested structure is modeled in the CSTMWS and the simulated findings are experimentally confirmed. The suggested antenna may be employed in current portable (5G) devices and the IoT. [ABSTRACT FROM AUTHOR]

Interrupted-sampling repeater modulation (ISRM) can generate multiple virtual target images by sampling and forwarding radar signals to confront the inverse synthetic aperture radar (ISAR). However, the repeating delay is unavoidable and the system is complex. Moreover, numerous works mainly discuss the ISAR image deception based on periodic modulation, and the modulation effect is relatively limited. Active frequency selective surface (AFSS) can perform intermittent amplitude modulation to the reflected signal by varying target reflectivity, thus, it can achieve the function of ISRM. In this paper, the possibility of AFSS applied in the multiple virtual target generation is discussed, and an ISAR image-modulation method is proposed. The radar signal is periodically modulated by varying target reflectivity, which is accomplished by the AFSS-loaded PIN diodes. On this basis, the AFSS modulating frequency is randomly varied in a slow time domain. When the modulation signal is processed by the ISAR system, the produced target image is unfocused and cannot be recognized by radar. Simulation results are utilized to demonstrate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a printed magnetic probe that can switch from broadband to tunable narrowband for near-field measurement. In the early design stage, we created a printed loop gap resonator as a magnetic reference sensor for the pre-compliance test in a band up to 6 GHz. Consequently, the results showed a good response in terms of the S11 and S21 parameters of the proposed probe compared with the commercial magnetic sensor XF-R 3-1. The source noise might spread among different frequency bands, making the broadband magnetic probe the closest choice for estimating the magnetic field in the near-field region. Unfortunately, broadband magnetic probes have lower sensitivity than narrowband ones. One of the solutions to get high sensitivity is to connect the LNA to the output of the passive magnetic sensor. This work proposes a novel method to solve this issue using a PIN diode to change the broadband status into a high sensitivity narrowband status and then tune this narrowband across the most critical applications such as 3.5 GHz, 3.75 GHz, 4.8 GHz, and 5.2 GHz with the help of a varactor diode. Compared to the broadband status, an improvement of more than 10 dB has been obtained across all these wireless bands. Furthermore, the proposed structure's isolation between the electrical and magnetic fields is about 13 dB. [ABSTRACT FROM AUTHOR]

This work is an overview of silicon photomultipliers (SiPMs) with a view to defining their importance for bio-photonic and clinical applications. SiPMs are benchmarked against other common photodetectors, namely, PIN diodes and avalanche photodetectors (APDs) and are compared with respect to important circuit design parameters. It will be shown that careful selection of the design bias voltage, overvoltage, gain defining components and device integration to micro-optics can allow SiPM detectors to achieve considerable sensitivity for auto-fluorescence (AF) detection and a wide dynamic range at low optical powers (~1 pW to ~4 μW). The SiPM has a manageable bias voltage (~25 V to ~30 V DC) for systems integration, and with optimised sensitivity it will enhance bio-photonic research in the area of AF to detect intraoperatively, for example, brain tumour margins. [ABSTRACT FROM AUTHOR]

In this paper, an active polarization conversion metasurface (APCM) operating in the X-band (8–12 GHz) is presented. Active unit cells consist of three metal layers and two substrate layers. Anisotropic metal patches, positive-intrinsic-negative (PIN) diodes, and bias lines are integrated into the surface layer to form a chiral structure. A simple and efficient polarization conversion function is realized in this designed structure. The operating mode is switched between linear-to-linear (LTL) polarization conversion and linear-to-circular (LTC) polarization conversion by switching the loaded PIN diode. In the LTL polarization conversion state, the polarization conversion ratio of APCM is over 90% in X-band. Reflected wave circular polarization axis ratio <3 dB in 8–12 GHz when in LTC state. The proposed structure is verified by experimental measurements. [ABSTRACT FROM AUTHOR]

Low-dose exposure and work convenience are required for mobile X-ray systems during the COVID-19 pandemic. We investigated a novel X-ray detector (FXRD-4343FAW, VIEWORKS, Anyang, Korea) composed of a thin-film transistor based on amorphous silicon with a flexible plastic substrate. This detector is composed of a thallium-doped cesium iodide scintillator with a pixel size of 99 μm, pixel matrix of 4316 × 4316, and weight of 2.95 kg. The proposed detector has the advantages of high-noise characteristics and low weight, which provide patients and workers with an advantage in terms of the dose and work efficiency, respectively. We performed a quantitative evaluation and an experiment to demonstrate its viability. The modulation transfer function, noise power spectrum, and detective quantum efficiency were identified using the proposed and comparative detectors, according to the International Electrotechnical Commission protocol. Additionally, the contrast-to-noise ratio and coefficient of variation were investigated using a human-like phantom. Our results indicate that the proposed detector efficiently increases the image performance in terms of noise characteristics. The detailed performance evaluation demonstrated that the outcomes of the use of the proposed detector confirmed the viability of mobile X-ray devices that require low doses. Consequently, the novel FXRD-4343FAW X-ray detector is expected to improve the image quality and work convenience in extended radiography. [ABSTRACT FROM AUTHOR]

This paper presents the design and realization of a flexible and frequency-reconfigurable antenna with harmonic suppression for multiple wireless applications. The antenna structure is derived from a quarter-wave monopole by etching slots. Afterward, the high-order unwanted harmonics are eliminated by adding a filtering stub to the feedline to avoid signal interference. Lastly, frequency reconfigurability is achieved using pin diodes by connecting and disconnecting the stubs and the rectangular patch. The antenna is fabricated on the commercially available thin (0.254 mm) conformal substrate of Rogers RT5880. The proposed antenna resonates (|S11| < –10 dB) at five different reconfigurable bands of 3.5 GHz (3.17–3.82 GHz), 2.45 GHz (2.27–2.64 GHz), 2.1 GHz (2.02–2.29 GHz), 1.9 GHz (1.81–2.05 GHz), and 1.8 GHz (1.66–1.93 GHz), which are globally used for 5G sub-6 GHz in industrial, medical, and scientific (ISM) bands, 4G long-term evolution (LTE) bands, and global system for mobile communication (GSM) bands. The simulated and measured results show that the antenna offers excellent performance in terms of good impedance matching with controllable resonant bands, high gain (>2 dBi), stable radiation patterns, and efficiency (>87%). Moreover, the conformal analysis shows that the antenna retains its performance both in flat and bending conditions, making it suitable for flexible electronics. In addition, the antenna is compared with the state-of-the-art works for similar applications to show its potential for the targeted band spectrums. [ABSTRACT FROM AUTHOR]