Search

The exploration and development of tight gas is a significant area of interest, yet the efficient development of this resource still faces considerable challenges. Statistical data indicate that China possesses approximately 1.5 × 1012 m3 of proven dense gas reserves, which are concentrated in areas with high water content and a low abundance of pores. This makes it challenging to utilise these reserves effectively and to extract them in a cost-effective manner. As exploration and development continue, numerous challenges emerge, including low production capacity, significant discrepancies between single gas wells, uncertain control reserves of horizontal gas wells, and the unclear distribution law of the remaining gas. In light of the aforementioned issues, this study examined a representative dense and high-water-bearing gas reservoir in the D gas wells region of the S gas field. The gas wells within the target gas block were classified and analysed. By elucidating the seepage mechanism of the dense and high-water-bearing gas reservoir and integrating it with the material balance equation, a recovery prediction method for the dense and high-water-bearing gas reservoir was devised. [ABSTRACT FROM AUTHOR]

The brittleness index, as the most important parameter for brittleness evaluation, directly affects the compressibility of unconventional reservoirs. Currently, there is no unified calculation method for the brittleness index. This article uses a three-axis rock mechanics servo testing system to test the rock mechanics parameters of shale oil reservoirs in Block Y of the Ordos Basin and uses an X'Pert PRO X-ray diffractometer to test the rock mineral composition. The average volume fraction of quartz minerals, feldspar, and clay minerals in 36 samples of Block Y was tested to be 22.6%, 51.6%, and 18%, respectively. Calcite, dolomite, and pyrite are only present in a few samples. When the confining pressure is 30 MPa, the elastic modulus of the Chang 7 shale in this block is 14.72–34.58 GPa, with an average value of 23.77 GPa; The Poisson's ratio ranges from 0.106 to 0.288, with an average of 0.182; The differential stress ranges from 100.8 to 260.1 MPa, with an average of 164.36 MPa; The peak strain ranges from 0.57 to 1.21, with an average of 0.91. This article compares several mainstream brittle index evaluation methods and identifies the most suitable brittle index evaluation method for Block Y. Using the Jarvie mineral composition method to calculate the brittleness index 1 (MBI), the average value of 36 experimental results is 0.5393. Using the Rickman normalized Young's modulus and Poisson's ratio average value to calculate the brittleness index 2 (EBI), the average value of 36 experimental results is 0.5204. Based on the stress-strain curve and energy method, a model for brittleness index 3 (DBI) is established, and the average value of 36 experimental results is 0.5306. The trend of the brittleness index calculated by the three methods is consistent, indicating the feasibility of the newly established brittleness evaluation method. From the perspectives of mineral composition, rock mechanics parameters, and energy, establishing a brittleness evaluation method for shale oil reservoirs and studying its evaluation method is of great significance for sweet spot prediction in reservoir engineering, providing theoretical support for the selection of fractured intervals in the Chang 7 shale oil reservoir in Block Y of the Ordos Basin. [ABSTRACT FROM AUTHOR]

Tight sandstone gas reservoirs generally contain water. Studying the impact of water content on the permeability mechanism of tight gas reservoirs is of positive significance for the rational development of gas reservoirs. Selected cores from a tight sandstone gas reservoir in the Ordos Basin were used to establish the variation in its seepage mechanism under different water saturations. The experimental results show that the gas slip factor in tight water-bearing gas reservoirs decreases as the water saturation increases. The stress sensitivity coefficient and the threshold pressure gradient (TPG) increase with increasing water saturation, characterizing the relationships between stress sensitivity coefficients, TPG, permeability, and water saturation. As the water saturation gradually increases, the relative gas phase permeability of tight sandstone gas reservoirs will sharply decrease. When the water saturation exceeds 80%, the gas phase permeability becomes almost zero, resulting in gas almost ceasing to flow. Through the analysis of experimental results, we defined high-water-cut tight sandstone gas reservoirs and analyzed the permeability characteristics of high-water-cut tight sandstone gas reservoirs in different regions. Combining stress sensitivity coefficients and the TPG with permeability and water saturation relationships, we established a zoning productivity calculation method of fractured horizontal wells in high-water-cut tight sandstone gas reservoirs under complex seepage conditions and validated the practicality of the model through example calculations. [ABSTRACT FROM AUTHOR]

Due to the high water saturation in high-water-cut tight sandstone gas reservoirs, factors such as threshold pressure gradient (TPG) and stress sensitivity (SS) cannot be overlooked in terms of their impact on seepage parameters. Therefore, this paper primarily investigates the seepage mechanisms in tight, high-water-cut sandstone gas reservoirs. While considering the influence of water saturation on various seepage mechanisms, it establishes a gas well productivity equation under stable seepage conditions and presents an analysis of the influencing factors. In a comparison of the unobstructed flow rates calculated using the productivity equation developed in this paper with those obtained from conventional gas well productivity equations and actual gas well productivity tests, the new equation demonstrates smaller errors. This provides a theoretical basis for evaluating productivity and making rational production allocation decisions in high-water-cut tight sandstone gas reservoirs. [ABSTRACT FROM AUTHOR]

After multi-stage volume hydraulic fracturing in a shale oil reservoir, massive amounts of water can be imbibed into the matrix pores. One of the key imbibition characteristics of a shale reservoir is the imbibition water and its height distribution. Based on high pressure mercury injection (HPMI) experiments and nuclear magnetic resonance (NMR) analyses, this study quantitatively evaluated the pore-size distribution of Chang 7 continental shale oil reservoirs in Yanchang Formation, Ordos Basin. The pores could be divided into three types as micropores (≤0.1 μm), mesopores (0.1–1.0 μm), and macropores (>1.0 μm), while the volume of micropores and mesopores accounted for more than 90%. This demonstrated that there were strong heterogeneity and micro–nano characteristics. According to the spontaneous imbibition (SI) experiments, the cumulative proportion of imbibition water content was the largest in micropores, exceeding 43%, followed by mesopores around 30%, and that of macropores was the lowest, and basically less than 20%. The negative values of stage water content in the macropore or mesopore indicated that these pores became a water supply channel for other dominant imbibition pores. Additionally, combining the fractal theory with the NMR T2 spectrum, the relative imbibition water and actual height were calculated in different pores, while the height distribution varied with cores and shale oil. The shorter the core, the higher was the relative height, while the radius of macropores filled with imbibition water was reduced. This indicates that the height distribution was affected by the pore structure, oil viscosity, and core length. [ABSTRACT FROM AUTHOR]

The Chang 7 continental shale oil reservoir is tight. The recovery factor is extremely low, the remaining oil is very high, and injecting water to improve oil recovery effectiveness is too hard. Therefore, in this paper, physical simulation experiments of CO2 huff-n-puff shale oil and NMR tests were conducted to study the cycle numbers and permeability on the recovery degree, as well as the characteristics of shale oil mobilization and the remaining oil micro distribution. The results showed that the cumulative oil recovery factors (ORFs) gradually increased in the natural logarithmic form, the single cycle ORFs decreased rapidly in exponential form with the huff-n-puff cycle number, and the biggest economic cycle numbers were between approximately 3 and 5. Furthermore, the higher the permeability, the higher the ORF, but the difference of ORF decreased between the two experimental samples with the cycles. In addition, the gap of production and recovery degree was large between the different scale pores, the ORF of macropores was 6–8 times that of micropores, and the final remaining oil was mainly distributed in the micropores, accounting for 82.29% of the total amount; meanwhile, the macropores comprised less than 0.5%. In the process of huff-n-puff, CO2 flowed into macropores, mesopores, and smallpores under the pressure differential effect, but a small amount of CO2 slowly diffused into micropores, resulting in the ORF of the former with more free oil being higher and the ORF of micropores with more adsorbed oil being lower. Therefore, promoting a better contact and reaction between CO2 and shale oil of micropores is one of the key ways to effectively develop the Chang 7 continental shale oil and enhance oil recovery. [ABSTRACT FROM AUTHOR]

Polymer microspheres (PMs) are used as a new material to recover residual oil left in unswept oil areas after secondary recovery methods. The fact that the PMs plug the macropores causes the flow direction of the injection fluid to be transferred from macropores to micropores. In order to investigate the plugging and profile control mechanisms of PMs in reservoirs, four kinds of PMs with different particle sizes and four kinds of artificial cores with different permeability were selected for flooding tests, including plugging experiments and profile control experiments. The pore throat size distribution of cores was characterized by nuclear magnetic resonance (NMR) technology. The particle size distribution of PMs used in the experiment was characterized using a laser particle size analyzer. The results showed that there are six matching relationships existing simultaneously between pore throats and PMs based on theoretical analysis, which are completely plugging, single plugging, bridge plugging, smooth passing, deposition, and deformable passing. A key principle for optimizing PMs in profile control is that the particle size of the selected PMs can enter the high permeability layer well, but it is difficult for it to enter the low permeability layer. The results of this paper provide a theoretical basis for the optimal particle size of PMs during the oil field profile control process. [ABSTRACT FROM AUTHOR]

Spontaneous imbibition of water into tight oil reservoirs is considered an effective way to improve tight oil recovery. We have combined testing techniques such as nuclear magnetic resonance, mercury injection capillary pressure, and magnetic resonance imaging to reveal the distribution characteristics of oil and water during the spontaneous imbibition process of tight sandstone reservoir. The experimental results were used to describe the dynamic process of oil–water distribution at the microscopic scale. The water phase is absorbed into the core sample by micropores and mesopores under capillary forces that dry away the original oil phase into the hydraulically connected macropores. The oil phase entering the macropores will drive away the oil in place and expel the original oil from the macropores. The results of magnetic resonance imaging clearly show that the remaining oil accumulates in the central region of the core because a large amount of water is absorbed in the late stage of spontaneous imbibition, and the water in the pores gradually connects to form a "water shield" that blocks the flow of the oil phase. We propose the spontaneous imbibition pathway, which can effectively explain the internal mechanisms controlling the spontaneous imbibition rate. The surface of the core tends to form many spontaneous imbibition pathways, so the rate of spontaneous imbibition is fast. The deep core does not easily form many spontaneous imbibition pathways, so the rate of spontaneous imbibition is slow. This paper reveals the pore characteristics and distribution of oil and water during the spontaneous imbibition process, which is of significance for the efficient development of tight oil. [ABSTRACT FROM AUTHOR]