Search

Our aim was to develop an accurate, highly sensitive method for HBV genotype determination and detection of genotype mixtures. We examined the preS and 5′ end of the HBV X gene (5X) regions of the HBV genome using next-generation sequencing (NGS). The 1852 haplotypes obtained were subjected to genotyping via the Distance-Based discrimination method (DB Rule) using two sets of 95 reference sequences of genotypes A–H. In clinical samples from 125 patients, the main genotypes were A, D, F and H in Caucasian, B and C in Asian and A and E in Sub-Saharan patients. Genotype mixtures were identified in 28 (22.40%) cases, and potential intergenotypic recombination was observed in 29 (23.20%) cases. Furthermore, we evaluated sequence conservation among haplotypes classified into genotypes A, C, D, and E by computing the information content. The preS haplotypes exhibited limited shared conserved regions, whereas the 5X haplotypes revealed two groups of conserved regions across the genotypes assessed. In conclusion, we developed an NGS-based HBV genotyping method utilizing the DB Rule for genotype classification. We identified two regions conserved across different genotypes at 5X, offering promising targets for RNA interference-based antiviral therapies. [ABSTRACT FROM AUTHOR]

Circulation of salty and fresh water through the electrodes of a deionization cell produces a voltage between the electrodes caused by the Capacitive Donnan Potential (CDP). The voltage so generated is very low (100 mV), but this work demonstrates that it is possible to develop a power converter suitable to inject this energy into the grid or into energy storage systems; this is a relevant aspect of this paper, for most works in the literature simply dissipate this energy over a resistor. To increase the input voltage, a stack of electrodes is connected in series. A bridgeless rectifier that uses a dual buck–boost converter to operate with both the positive and negative cycles is used to extract the energy from the cell. The topology chosen, which is operated as a current source, can work at extremely low voltage levels and provide power factor correction. After this stage, an H-bridge inverter can be included to inject the energy into the AC grid. The whole system implements a hysteresis control system using the current through the inductor of the power converter as control variable. This paper investigates the influence of such current on the efficiency of the total system. [ABSTRACT FROM AUTHOR]

Naturally derived polysaccharide-based hydrogels, such as alginate, are frequently used in the design of bioinks for 3D bioprinting. Traditionally, the formulation of such bioinks requires the use of pre-reticulated materials with low viscosities, which favour cell viability but can negatively influence the resolution and shape fidelity of the printed constructs. In this work, we propose the use of cellulose nanocrystals (CNCs) as a rheological modifier to improve the printability of alginate-based bioinks whilst ensuring a high viability of encapsulated cells. Through rheological analysis, we demonstrate that the addition of CNCs (1% and 2% (w/v)) to alginate hydrogels (1% (w/v)) improves shear-thinning behaviour and mechanical stability, resulting in the high-fidelity printing of constructs with superior resolution. Importantly, LIVE/DEAD results confirm that the presence of CNCs does not seem to affect the health of immortalised chondrocytes (TC28a2) that remain viable over a period of seven days post-encapsulation. Taken together, our results indicate a favourable effect of the CNCs on the rheological and biocompatibility properties of alginate hydrogels, opening up new perspectives for the application of CNCs in the formulation of bioinks for extrusion-based bioprinting. [ABSTRACT FROM AUTHOR]

The repair of the damage produced to the genome and proteome by the action of ionizing radiation, oxidizing agents, and during aging is important to maintain cellular homeostasis. Many of the metabolic pathways influence multiple processes. In this way, this work aims to study the relationship between resistance/response to ionizing radiation, cellular aging, and the response mechanisms to oxidative stress, free radicals, reactive oxygen species (ROS), and antioxidant activity in the yeast S. cerevisiae. Systems biology allows us to use tools that reveal the molecular mechanisms common to different cellular response phenomena. The results found indicate that homologous recombination, non-homologous end joining, and base excision repair pathways are the most important common processes necessary to maintain cellular homeostasis. The metabolic routes of longevity regulation are those that jointly contribute to the three phenomena studied. This study proposes eleven common biomarkers for response/resistance to ionizing radiation and aging (EXO1, MEC1, MRE11, RAD27, RAD50, RAD51, RAD52, RAD55, RAD9, SGS1, YKU70) and two biomarkers for response/resistance to radiation and oxidative stress, free radicals, ROS, and antioxidant activity (NTG1, OGG1). In addition, it is important to highlight that the HSP104 protein could be a good biomarker common to the three phenomena studied. [ABSTRACT FROM AUTHOR]

Simple Summary: Among 1083 patients with HN cancer, 11 patients with neuroendocrine carcinomas (NECs) of the head and neck (HN) were identified. In our series, HN NECs diagnosed with localized or locally advanced disease achieved long-lasting survival with multimodality treatment. HN NECs harbored mutations in TP53, HFN1A and RB1, among others, had a median TMB of 6.72 muts/Mb and showed wide TCR repertoires. Among three patients with metastatic disease that received anti-PD1 therapy, there were two long-lasting responders. Neuroendocrine carcinomas (NECs) of the head and neck (HN) account for <1% of HN cancers (HNCs), with a 5-year overall survival (OS) <20%. This is a retrospective study of HN NECs diagnosed at our institution between 2005 and 2022. Immunohistochemistry and next-generation sequencing (NGS) were used to evaluate neuroendocrine markers, tumor mutational burden (TMB), mutational profiles and T-cell receptor repertoires. Eleven patients with high-grade HN NECs were identified (male:female ratio 6:5; median age 61 (Min–Max: 31–86)): nasoethmoidal (3), parotid gland (3), submaxillary gland (1), larynx (3) and base of tongue (1). Among n = 8 stage II/IVA/B, all received (chemo)radiotherapy with/without prior surgery or induction chemotherapy, with complete response in 7/8 (87.5%). Among n = 6 recurrent/metastatic patients, three received anti-PD1 (nivolumab (2), pembrolizumab (1)): two achieved partial responses lasting 24 and 10 months. After a median follow-up of 30 and 23.5 months since diagnosis and since recurrent/metastatic, median OS was not reached. Median TMB (n = 7) was 6.72 Mut/Mb. The most common pathogenic variants were TP53, HNF1A, SMARCB1, CDKN2A, PIK3CA, RB1 and MYC. There were 224 median TCR clones (n = 5 pts). In one patient, TCR clones increased from 59 to 1446 after nivolumab. HN NECs may achieve long-lasting survival with multimodality treatment. They harbor moderate-high TMBs and large TCR repertoires, which may explain responses to anti-PD1 agents in two patients and justify the study of immunotherapy in this disease. [ABSTRACT FROM AUTHOR]

Climate change in the Mediterranean area is making summers warmer and dryer. Grapevine (Vitis vinifera L.) is mostly important for wine production in Mediterranean countries, and the variety Tempranillo is one of the most cultivated in Spain and Portugal. Drought decreases yield and quality and causes important economic losses. As full irrigation has negative effects on quality and water is scarce in this region, deficit irrigation is often applied. In this research, we studied the effects of two deficit irrigation treatments, Sustained Deficit Irrigation (SDI) and Regulated Deficit Irrigation (RDI), on the transcriptome of grape berries at full maturation, through RNAseq. The expression of differentially regulated genes (DEGs) was also monitored through RT-qPCR along berry development. Most transcripts were regulated by water stress, with a similar distribution of up- and down-regulated transcripts within functional categories (FC). Primary metabolism was the more severely affected FC under water stress, followed by signaling and transport. Almost all DEGs monitored were significantly up-regulated by severe water stress at veraison. The modulation of an auxin response repression factor, AUX22D, by water stress indicates a role of this gene in the response to drought. Further, the expression of WRKY40, a TF that regulates anthocyanin biosynthesis, may be responsible for changes in grape quality under severe water stress. [ABSTRACT FROM AUTHOR]

Good health and well-being are primary goals within the list of Sustainable Development Goals (SDGs) proposed by the United Nations (UN) in 2015. New technologies, such as Internet of Things (IoT) and Cloud Computing, can aid to achieve that goal by enabling people to improve their lifestyles and have a more healthy and comfortable life. Pollution monitoring is especially important in order to avoid exposure to fine particles and to control the impact of human activity on the natural environment. Some of the sources of hazardous gas emissions can be found indoors. For instance, carbon monoxide (CO), which is considered a silent killer because it can cause death, is emitted by water heaters and heaters that rely on fossil fuels. Existing solutions for indoor pollution monitoring suffer from some drawbacks that make their implementation impossible for households with limited financial resources. This paper presents the development of IdeAir, a low-cost IoT-based air quality monitoring system that aims to reduce the disadvantages of existing systems. IdeAir was designed as a proof of concept to capture and determine the concentrations of harmful gases in indoor environments and, depending on their concentration levels, issue alarms and notifications, turn on the fan, and/or open the door. It has been developed following the Test-Driven Development Methodology for IoT-based Systems (TDDM4IoTS), which, together with the tool (based on this methodology) used for the automation of the development of IoT-based systems, has facilitated the work of the developers. Preliminary results on the functioning of IdeAir show a high level of acceptance by potential users. [ABSTRACT FROM AUTHOR]

Throughout the evolution of software systems, empirical methodologies have been used in their development process, even in the Internet of Things (IoT) paradigm, to develop IoT-based systems (IoTS). In this paper, we review the fundamentals included in the manifesto for agile software development, especially in the Scrum methodology, to determine its use and role in IoTS development. Initially, 4303 documents were retrieved, a number that was reduced to 186 after applying automatic filters and by the relevance of their titles. After analysing their contents, only 60 documents were considered. Of these, 38 documents present the development of an IoTS using some methodology, 8 present methodologies focused on the construction of IoTS software, and 14 present methodologies close to the systems life cycle (SLC). Finally, only one methodology can be considered SLC-compliant. Out of 38 papers presenting the development of some IoTS following a methodology for traditional information systems (ISs), 42.1% have used Scrum as the only methodology, while 10.5% have used Scrum combined with other methodologies, such as eXtreme Programming (XP), Kanban and Rapid Prototyping. In the analysis presented herein, the existing methodologies for developing IoTSs have been grouped according to the different approaches on which they are based, such as agile, modelling, and service oriented. This study also analyses whether the different proposals consider the standard stages of the development process or not: planning and requirements gathering, solution analysis, solution design, solution coding and unit testing (construction), integration and testing (implementation), and operation and maintenance. In addition, we include a review of the automated frameworks, platforms, and tools used in the methodologies analysed to improve the development of IoTSs and the design of their underlying architectures. To conclude, the main contribution of this work is a review for IoTS researchers and developers regarding existing methodologies, frameworks, platforms, tools, and guidelines for the development of IoTSs, with a deep analysis framed within international standards dictated for this purpose. [ABSTRACT FROM AUTHOR]

Featured Application: Characterization of the corneal nerve fibers is gaining popularity for objective assessment of anterior segment anomalies such as dry eye disease. Confocal microscopy provides high-resolution imaging of the sub-basal plexus; thus, several parameters such as corneal length, density or tortuosity can be analyzed. However, the analysis of these images is usually performed based on manual or semiautomated methods, many of which are subjective and time consuming. In this work, a fully automated tortuosity corneal nerve fiber analysis method is proposed. This new tool may be very useful to obtain an accurate evaluation of nerve alterations, to monitor changes over time and/or in response to treatment, to ensure comparisons across different studies or even to improve the diagnosis of ocular surface diseases. An automated tool for corneal nerve fiber tortuosity quantification from in vivo confocal microscopy (IVCM) is described and evaluated. The method is a multi-stage process based on the splitting of the corneal nerve fibers into individual segments, whose endpoints are an extreme or intersection of white pixels on a binarized image. Individual segment tortuosity is quantified in terms of the arc-chord ratio. Forty-three IVCM images from 43 laser-assisted in situ keratomileusis (LASIK) surgery patients were used for evaluation. Images from symptomatic dry eye disease (DED) post-LASIK patients, with ( n = 16 ) and without ( n = 7 ) ocular pain, and non-DED post-LASIK controls ( n = 20 ) were assessed. The automated tortuosity measure was compared to a manual grading one, obtaining a moderate correlation (Spearman's rank correlation coefficient = 0.49 , p = 0.0008 ). The new tortuosity index was significantly higher in post-LASIK patients with ocular pain than in control patients ( p = 0.001 ), while no significant differences were detected with manual measurement ( p > 0.28 ). The tortuosity quantification was positively correlated with the ocular surface disease index (OSDI) and a numeric rating scale (NRS) assessing pain ( p = 0.0012 and p = 0.0051 , respectively). The results show good performance of the proposed automated methodology for the evaluation of corneal nerve tortuosity. [ABSTRACT FROM AUTHOR]

Simple Summary: The wild Agave marmorata Roezl has been classified as an endangered species. Extracting these plants from the forest for commercial purposes and long maturation periods of close to 30 years have contributed to their loss. A. marmorata interacts with pollinators and other Agaves species to maintain genetic variability. Thus, the conservation and restoration of the agave ecosystem is an ecological challenge. Typically, agave micropropagation use meristem or leaves as explants to rapidly produce uniform agave plants in age and size on a large scale leading to homogeneous plantations. However, introducing these clones to the field reduces genetic variability. This study evaluated in vitro micropropagation of A. marmorata from seeds to generate clonal lines. The selected seedlings exhibited variations in multiplication capacity and stable tissue formation. Variations in clonal lines could be exploited to produce high-quality plants with different capacities, such as faster propagation, enhanced stress adaptation, and continued growth under nutrient limitation conditions, consequently maintaining genetic variability. Furthermore, some clonal lines were inoculated with four endophytic bacteria to identify other differences among these plants, including endophyte-host compatibility. Variable responses to inoculation were observed among clonal lines. We found that Achromobacter xylosoxidans was compatible, unlike Enterobacter cloacae which caused plant death. A. marmorata is the raw material used for tepextate mescal production but is classified as an endangered species. In the present study, we obtain and multiply clonal lines of Agave marmorata Roezl by selecting seedlings derived from seeds. Ten seedlings from two lots of 400 germinated seeds were selected for axillary bud proliferation induced by BAP 5 mg/L in vitamin-free Murashige and Skoog's medium. Differences in shoot numbers, heights and senescent tissue formation were observed. Notably, the AM32 line formed 84 shoots and presented low senescent tissue after 60 d of culture. We also selected the AM31 and AM33 clonal lines. Four-month shoots were extracted with 80% methanol in water to determine the total content of saponins, flavonoids, and phenolic acids and compare the three clonal lines. Some bioactive molecules were identified using HPLC techniques and MALDI-TOF mass spectrometry none showed significant differences in content. Additionally, plants derived from the clonal lines were inoculated with four endophytic bacteria. Among these, Achromobacter xylosoxidans supported plant growth of AM32. A notable effect of plant death was observed after inoculation with Enterobacter cloacae, an endophyte of A. tequilana. Additionally, Pseudomonas aeruginosa, an endophyte from A. marmorata, reduced biomass. Our results demonstrate the incompatibility of A. marmorata to E. cloacae and specialization between the host plant and its endophytes. The compatibility of the plant-endophyte could be exploited to boost the establishment and stability of mutualisms to benefit plant development, stress tolerance and pathogen resistance. The differences in multiplication capacity, stable tissue formation, and endophyte biotization responses may indicate genetic variability. Clonal selection and micropropagation from seed-derived plants could contribute to conserving the endangered A. marmorata plant for reforestation in their natural habitats, thus, assuring mass propagation for sustainable industrial production of mescal, bioactive compounds, and prebiotics. [ABSTRACT FROM AUTHOR]

A study is carried out which investigates the effects of the mono-vacancies of boron (VB) and nitrogen (VN) and the co-vacancies of nitrogen (N), and boron (B) on the energetics and the structural, electronic, and magnetic properties of an h-BN/graphene heterobilayer using first-principles calculations within the framework of the density functional theory (DFT). The heterobilayer is modelled using the periodic slab scheme. In the present case, a 4 × 4-(h-BN) monolayer is coupled to a 4 × 4-graphene monolayer, with a mismatch of 1.40%. In this coupling, the surface of interest is the 4 × 4-(h-BN) monolayer; the 4 × 4-graphene only represents the substrate that supports the 4 × 4-(h-BN) monolayer. From the calculations of the energy of formation of the 4 × 4-(h-BN)/4 × 4-graphene heterobilayer, with and without defects, it is established that, in both cases, the heterobilayers are energetically stable, from which it is inferred that these heterobilayers can be grown in the experiment. The formation of a mono-vacancy of boron (1 VB), a mono-vacancy of nitrogen (1 VN), and co-vacancies of boron and nitrogen (VBN) induce, on the structural level: (a) for 1 VB, a contraction n of the B-N bond lengths of ~2.46% and a slight change in the interfacial distance D (~0.096%) with respect to the heterobilayer free of defects (FD) are observed; (b) for 1 VN, a slight contraction of the B-N of bond lengths of ~0.67% and an approach between the h-BN monolayer and the graphene of ~3.83% with respect to the FD heterobilayer are observed; (c) for VBN, it can be seen that the N-N and B-B bond lengths (in the 1 VB and 1 VN regions, respectively) undergo an increase of ~2.00% and a decrease of ~3.83%, respectively. The calculations of the Löwdin charge for the FD heterobilayer and for those with defects (1 VB, 1 VN, and VBN) show that the inclusion of this type of defect induces significant changes in the Löwdin charge redistribution of the neighboring atoms of VB and VN, causing chemically active regions that could favor the interaction of the heterobilayer with external atoms and/or molecules. On the basis of an analysis of the densities of states and the band structures, it is established that the heterobilayer with 1 VB and VBN take on a half-metallic and magnetic behavior. Due to all of these properties, the FD heterobilayer and those with 1 VB, 1 VN, and VBN are candidates for possible adsorbent materials and possible materials that could be used for different spintronic applications. [ABSTRACT FROM AUTHOR]

The effects of the monovacancies of oxygen (VO) and manganese (VMn) on the structural and electronic properties of the 1T–MnO2/graphene heterostructure are investigated, within the framework of density functional theory (DFT). We found that the values of the formation energy for the heterostructure without and with vacancies of VO and VMn were −20.99 meV Å 2   , −32.11 meV Å 2 , and −20.81 meV Å 2 , respectively. The negative values of the formation energy indicate that the three heterostructures are energetically stable and that they could be grown in the experiment (exothermic processes). Additionally, it was found that the presence of monovacancies of VO and VMn in the heterostructure induce: (a) a slight decrease in the interlayer separation distance in the 1T–MnO2/graphene heterostructure of ~0.13% and ~1.41%, respectively, and (b) a contraction of the (Mn−O) bond length of the neighboring atoms of the VO and VMn monovacancies of ~2.34% and ~6.83%, respectively. Calculations of the Bader charge for the heterostructure without and with VO and VMn monovacancies show that these monovacancies induce significant changes in the charge of the first-neighbor atoms of the VO and VMn vacancies, generating chemically active sites (locales) that could favor the adsorption of external atoms and molecules. From the analysis of the density of state and the structure of the bands, we found that the graphene conserves the Dirac cone in the heterostructure with or without vacancies, while the 1T–MnO2 monolayer in the heterostructures without and with VO monovacancies exhibits half-metallic and magnetic behavior. These properties mainly come from the hybridization of the 3d–Mn and 2p–O states. In both cases, the heterostructure possesses a magnetic moment of 3.00 μβ/Mn. From this behavior, it can be inferred the heterostructures with and without VO monovacancies could be used in spintronics. [ABSTRACT FROM AUTHOR]

Grapevine (Vitis vinifera L.) is one of the most economically important crops worldwide, especially due to the economic relevance of wine production. Abiotic stress, such as drought, may contribute to low yield, shifts in quality, and important economic loss. The predicted climate change phenomena point to warmer and dryer Mediterranean environmental conditions; as such, it is paramount to study the effects of abiotic stress on grapevine performance. Deficit irrigation systems are applied to optimize water use efficiency without compromising berry quality. In this research, the effect of two deficit irrigation strategies, sustained deficit irrigation (SDI) and regulated deficit irrigation (RDI), in the grape berry were assessed. The effects of different levels of drought were monitored in Touriga Nacional at key stages of berry development (pea size, véraison, and full maturation) through RNA-Seq transcriptome analysis and by specific differentially expressed genes (DEGs) monitoring through RT-qPCR. Handy datasets were obtained by bioinformatics analysis of raw RNA-Seq results. The dominant proportion of transcripts was mostly regulated by development, with véraison showing more upregulated transcripts. Results showed that primary metabolism is the functional category more severely affected under water stress. Almost all DEGs selected for RT-qPCR were significantly upregulated in full maturation and showed the highest variability at véraison and the lowest gene expression values in the pea size stage. [ABSTRACT FROM AUTHOR]

In an unbalanced linear three-phase electrical system, there are inefficient powers that increase the apparent power supplied by the network, line losses, machine malfunctions, etc. These inefficiencies are mainly due to the use of unbalanced loads. Unlike a three-wire unbalanced system, a four-wire system has zero sequence currents that circulate through the neutral wire and can be compensated by means of compensation equipment, which prevents it from being delivered by the network. To design a compensator that works with unbalanced voltages, it is necessary to consider the interactions between it and the other compensators used to compensate for negative-sequence currents and positive-sequence reactive currents. In this paper, through passive compensation, a new method is proposed to develop the zero sequence current compensation equipment. The method does not require iteration algorithms and is valid for unbalanced voltages. In addition, the interactions between all compensators are analyzed, and the necessary modifications in the calculations are proposed to obtain a total compensation. To facilitate the application of the method and demonstrate its validity, a case study is developed from a three-phase linear four-wire system with unbalanced voltages and loads. The results obtained are compared with other compensation methods that also use passive elements. [ABSTRACT FROM AUTHOR]

The compensation of an electrical system from passive compensators mainly focuses on linear systems where the consumption of charges does not vary significantly over time. In three-phase three-wire systems, when the network voltages are unbalanced, negative-sequence voltages and currents appear, which can significantly increase the total apparent power supplied by the network. This also increases the network losses. This paper presents a method for calculating the compensation of the positive-sequence reactive power and unbalanced powers caused by the negative-sequence line currents using reactive elements (coils and/or capacitors). The compensation is applied to three-phase three-wire linear systems with unbalanced voltages and loads, which are connected to an infinite power network. The method is independent of the load characteristics, where only the line-to-line voltages and line currents, at the point where compensation is desired, need to be known in advance. The solution obtained is optimal, and the system observed from the network behaves as one that only consumes the active power required by a load with a fully balanced current system. To understand the proposed method and demonstrate its validity, a case study of a three-phase three-wire linear system connected to an infinite power network with unbalanced voltages and currents is conducted. [ABSTRACT FROM AUTHOR]

Fluorescence resonance energy transfer (FRET)-based sensors for 3′–5′ cyclic adenosine monophosphate (cAMP) and protein kinase A (PKA) allow real-time imaging of cAMP levels and kinase activity in intact cells with high spatiotemporal resolution. The development of FRET-based sensors has made it possible to directly demonstrate that cAMP and PKA signals are compartmentalized. These sensors are currently widely used to dissect the organization and physiological function of local cAMP/PKA signaling events in a variety of cell systems. Fusion to targeting domains has been used to direct the sensors to a specific subcellular nanodomain and to monitor cAMP and PKA activity at specific subcellular sites. Here, we investigate the effects of using the A-kinase anchoring protein 79 (AKAP79) as a targeting domain for cAMP and PKA FRET-based reporters. As AKAP79 interacts with PKA itself, when used as a targeting domain, it can potentially impact on the amplitude and kinetics of the signals recorded locally. By using as the targeting domain wild type AKAP79 or a mutant that cannot interact with PKA, we establish that AKAP79 does not affect the amplitude and kinetics of cAMP changes or the level of PKA activity detected by the sensor. [ABSTRACT FROM AUTHOR]

In solar thermal power plants molten salt is often used to store and transport the energy that is collected during the day. The external pipe temperature is measured to activate an electric heating system if the temperature approaches the melting point. However, salt solidification cannot be completely excluded from the plant management. Once occurred, the location of a salt blockage is very complex due to the high temperature of the pipe. Therefore, when this problem arises, power plants have to stop production with the consequences in time and cost that this entails. Electro-magnetic acoustic transducers can be used as non-destructive testing systems for this application. A method for salt blockage detection is proposed that is applicable in straight sections of pipes by employing torsional guided waves that are generated with magnetostrictive transducers. The present paper deals with the transducer conception and the design of the power supply to activate it. Two alternatives are proposed and compared to determine the improvement in the amplitude/noise ratio. Finally, the experimental results show the performance of the equipment in a small prototype, thus validating the technique presented. [ABSTRACT FROM AUTHOR]

Electrostatic precipitators (ESPs) are devices used in industry to eliminate polluting particles in gases. In order to supply them, an interface must be included between the three-phase main line and the required high DC voltage of tens of kilovolts. This paper describes an 80-kW power supply for such an application. Its structure is based on the series parallel resonant converter with a capacitor as output filter (PRC-LCC), which can adequately cope with the parasitic elements of the step-up transformer involved. The physical implementation of the prototype includes the use of silicon carbide--SiC--semiconductors, which provide better switching capabilities than their traditional silicon--Si--counterparts. As a result, a new control strategy results as a better alternative in which the resonant current is maintained in phase with the first harmonic of the inverter voltage. Although this operation mode imposes hard switching in one of the inverter legs, it minimizes the reactive energy that circulates through the resonant tank, the resonant current amplitude itself and the switching losses. Overall efficiency of the converter benefits from this. These ideas are supported mathematically using the steady state and dynamic models of the topology. They are confirmed with experimental measurements that include waveforms, Bode plots and thermal behavior. The experimental setup delivers 80 kW with an estimated efficiency of 98%. [ABSTRACT FROM AUTHOR]

Medical X-ray appliances use high-voltage power supplies that must be able to work with very different energy requirements. Two techniques can be distinguished in X-ray medical imaging: fluoroscopy and radioscopy. The former involves low power radiation with a long exposure time, while radioscopy requires large power during short radiographic exposure times. Since the converter has to be designed by taking into account the maximum power specification, it will exhibit a poor efficiency when operating at low power levels. Such a problem can be solved by using a new multilevel LCC topology. This topology is based on a classical series-parallel resonant topology, but includes an additional low-voltage auxiliary transformer whose function depends on the X-ray technique considered. When radioscopy operation is selected, the transformer will allow the power to be shared between two full-bridges. If fluoroscopy mode is activated, the auxiliary full bridge is disconnected and the magnetizing inductance of the auxiliary transformer is used to increase the resonant inductor in order to reduce the resonant currents, thus improving the efficiency of the converter. [ABSTRACT FROM AUTHOR]

There is, at present, considerable interest in the storage and dispatchability of photovoltaic (PV) energy, together with the need to manage power flows in real-time. This paper presents a new system, PV-on time, which has been developed to supervise the operating mode of a Grid-Connected Utility-Scale PV Power Plant in order to ensure the reliability and continuity of its supply. This system presents an architecture of acquisition devices, including wireless sensors distributed around the plant, which measure the required information. It is also equipped with a high-precision protocol for synchronizing all data acquisition equipment, something that is necessary for correctly establishing relationships among events in the plant. Moreover, a system for monitoring and supervising all of the distributed devices, as well as for the real-time treatment of all the registered information, is presented. Performances were analyzed in a 400 kW transformation center belonging to a 6.1 MW Utility-Scale PV Power Plant. In addition to monitoring the performance of all of the PV plant's components and detecting any failures or deviations in production, this system enables users to control the power quality of the signal injected and the influence of the installation on the distribution grid. [ABSTRACT FROM AUTHOR]

Many thermal solar power plants use thermal oil as heat transfer fluid, and molten salts as thermal energy storage. Oil absorbs energy from sun light, and transfers it to a water-steam cycle across heat exchangers, to be converted into electric energy by means of a turbogenerator, or to be stored in a thermal energy storage system so that it can be later transferred to the water-steam cycle. The complexity of these thermal solar plants is rather high, as they combine traditional engineering used in power stations (water-steam cycle) or petrochemical (oil piping), with the new solar (parabolic trough collector) and heat storage (molten salts) technologies. With the engineering of these plants being relatively new, regulation of the thermal energy storage system is currently achieved in manual or semiautomatic ways, controlling its variables with proportional-integral-derivative (PID) regulators. This makes the overall performance of these plants non optimal. This work focuses on energy storage systems based on molten salt, and defines a complete model of the process. By defining such a model, the ground for future research into optimal control methods will be established. The accuracy of the model will be determined by comparing the results it provides and those measured in the molten-salt heat storage system of an actual power plant. [ABSTRACT FROM AUTHOR]

The cornea is a very particular tissue due to its transparency and its barrier function as it has to resist against the daily insults of the external environment. In addition, maintenance of this barrier function is of crucial importance to ensure a correct corneal homeostasis. Here, the corneal epithelial permeability has been assessed in vivo by means of non-invasive tetrapolar impedance measurements, taking advantage of the huge impact of the ion fluxes in the passive electrical properties of living tissues. This has been possible by using a flexible sensor based in SU-8 photoresist. In this work, a further analysis focused on the validation of the presented sensor is performed by monitoring the healing process of corneas that were previously wounded. The obtained impedance measurements have been compared with the damaged area observed in corneal fluorescein staining images. The successful results confirm the feasibility of this novel method, as it represents a more sensitive in vivo and non-invasive test to assess low alterations of the epithelial permeability. Then, it could be used as an excellent complement to the fluorescein staining image evaluation. [ABSTRACT FROM AUTHOR]

With photovoltaic (PV) systems proliferating in the last few years due to the high prices of fossil fuels and pollution issues, among others, it is extremely important to monitor the efficiency of these plants and optimize the energy production process. This will also result in improvements related to the maintenance and security of the installation. In order to do so, the main parameters in the plant must be continuously monitored so that the appropriate actions can be carried out. This monitoring should not only be carried out at a global level, but also at panel-level, so that a better understanding of what is actually happening in the PV plant can be obtained. This paper presents a system based on a wireless sensor network (WSN) that includes all the components required for such monitoring as well as a power supply obtaining the energy required by the sensors from the photovoltaic panels. The system proposed succeeds in identifying all the nodes in the network and provides real-time monitoring while tracking efficiency, features, failures and weaknesses from a single cell up to the whole infrastructure. Thus, the decision-making process is simplified, which contributes to reducing failures, wastes and, consequently, costs. [ABSTRACT FROM AUTHOR]

In this study, we first prove a parameterized integral identity involving differentiable functions. Then, for differentiable harmonically convex functions, we use this result to establish some new inequalities of a midpoint type, trapezoidal type, and Simpson type. Analytic inequalities of this type, as well as the approaches for solving them, have applications in a variety of domains where symmetry is important. Finally, several particular cases of recently discovered results are discussed, as well as applications to the special means of real numbers. [ABSTRACT FROM AUTHOR]

Symptoms of chronic cough (CC) from the airways are commonly treated with antibiotics, antitussives, bronchodilators, and steroids. There is a wide variability in treatment response, dependent on the exact cough etiology. Our case-series study was composed of 71 nonsmoking adults, 59 females, mean age 43 (±21) years, with a history of CC-asthma and history of ≥2 exacerbations/year requiring systemic steroids and/or antibiotics. All had decreased Streptococcus pneumoniae antibody titers, with a mean average of 3 of 23 normal serotypes and were subsequently vaccinated with PPSV-23. Pre- and post-12-month vaccination questionnaires were administered, and 35 (54%) reported both decreased CC symptoms and asthma medication use. Baseline comparisons to those with no change in CC symptoms or asthma medication use revealed significantly lower exhaled nitric oxide (FeNO) levels (17 ± 10; 62 + 40 ppb), serum eosinophils (192 ± 156; 280 ± 166/mcL), and total IgE (132 ± 167; 275 ± 290 IU/mL) in those with improvement post-vaccination. Higher baseline symptoms scores for upper respiratory infections as a trigger to their CC (* p > 0.05) were found in those responding to PPSV-23. These data reveal a subset of asthma in younger adults, <65 years, with significantly decreased S. pneumoniae antibody titers with less CC symptoms and asthma medication use for exacerbations after PPSV-23 vaccination. [ABSTRACT FROM AUTHOR]

Poor electron-related cutting current in graphene-based field-effect transistors (FETs) can be solved by placing a graphene layer over a hexagonal boron nitride (BN) substrate, as established by Giovannetti et al. and other researchers. In order to produce high-quality results, this investigation uses 2 × 2 cells (~2.27% mismatch), given that larger cells lead to more favourable considerations regarding interactions on cell edges. In this case, the substrate-induced band gap is close to 138 meV. In addition, we propose a new material based on graphene on BN in order to take advantage of the wonderful physical properties of both graphene and BN. In this new material, graphene is rotated with respect to BN, and it exhibits a better mismatch, only ~1.34%, than the 1 × 1-graphene/1 × 1-BN; furthermore, it has a very small bandgap, which is almost zero. Therefore, in the bands, there are electronic states in cone form that are like the Dirac cones, which maintain the same characteristics as isolated graphene. In the first case (2 × 2-graphene/2 × 2-BN), for example, the resulting band gap of 138 meV is greater than Giovannetti's value by a factor of ~2.6. The 2 × 2-graphene/2 × 2-BN cell is better than the 1 × 1-graphene/BN one because a greater bandgap is an improvement in the cutting current of graphene-based FETs, since the barrier created by the bandgap is larger. The calculations in this investigation are performed within the density functional theory (DFT) theory framework, by using 2 × 2-graphene/2 × 2-BN and 13 × 13 -graphene/ 2 3 × 2 3 -(0001) BN cells. Pseudopotentials and the generalized gradient approximation (GGA), combined with the Perdew–Burke–Ernzerhof parametrization, were used. Relaxation is allowed for all atoms, except for the last layer of the BN substrate, which serves as a reference for all movements and simulates the bulk BN. [ABSTRACT FROM AUTHOR]

In this work, we prove a new (p , q) -integral identity involving a (p , q) -derivative and (p , q) -integral. The newly established identity is then used to show some new Simpson's formula type inequalities for (p , q) -differentiable convex functions. Finally, the newly discovered results are shown to be refinements of comparable results in the literature. Analytic inequalities of this type, as well as the techniques used to solve them, have applications in a variety of fields where symmetry is important. [ABSTRACT FROM AUTHOR]

Currently available anti-viral drugs may be useful in reducing the viral load but are not providing the necessary physiological effects to reduce the SARS-CoV-2 complications efficiently. Treatments that provide better clinical outcomes are urgently needed. Vitamin C (ascorbic acid, AA) is an essential nutrient with many biological roles that have been proven to play an important part in immune function; it serves as an antioxidant, an anti-viral, and exerts anti-thrombotic effects among many other physiological benefits. Research has proven that AA at pharmacological doses can be beneficial to patients with acute respiratory distress syndrome (ARDS) and other respiratory illnesses, including sepsis. In addition, High-Dose Intravenous Vitamin C (HDIVC) has proven to be effective in patients with different viral diseases, such as influenza, chikungunya, Zika, and dengue. Moreover, HDIVC has been demonstrated to be very safe. Regarding COVID-19, vitamin C can suppress the cytokine storm, reduce thrombotic complications, and diminish alveolar and vascular damage, among other benefits. Due to these reasons, the use of HDIVC should be seriously considered in complicated COVID-19 patients. In this article, we will emphasize vitamin C's multiple roles in the most prominent pathophysiological processes presented by the COVID-19 disease. [ABSTRACT FROM AUTHOR]

In recent decades, a growing awareness of the importance of preserving cultural heritage as a means of promoting sustainable development has been accompanied by a similar re-evaluation of the role of heritage education as a key driver of citizen engagement. The development and implementation of heritage education at all levels, particularly in the context of teacher training, is of vital importance. The aim of this study is to analyse student teachers' understanding of heritage and its potential as an educational tool, in order to identify measures to enhance teacher training and practice with respect to heritage and heritage education. The research design consists of a comparative study of a non-random sample of 149 trainee teachers undertaking Bachelor's degrees in Early Childhood Education and Primary Education at the University of Córdoba (Spain). The results reveal a mainly cultural conception of heritage among both groups, based on local material elements, and little sense of the link between heritage and present-day life. The students studying early childhood education were found to display a more specific knowledge of heritage in their answers, while the primary education students showed a greater awareness of identity and values as features of cultural heritage. [ABSTRACT FROM AUTHOR]

Since the early work of Justus von Liebig on nutrient absorption in plants in the 1800s [[1]], industrial agriculture has been trapped in a "chemical paradigm" that holds that agrochemicals (inorganic fertilizers, pesticides, fungicides, and herbicides) are essential to producing healthy crops and increase crop yields. In order to grow crops, plant microbiomes may be augmented with microbes that function in plants - perhaps acquired from wild relatives of crop plants [[2]]. Introduction to Special Issue: Plant Microbiome Augmentation and Stimulation - New Strategies to Grow Crops with Reduced Agrochemicals. [Extracted from the article]

A detailed knowledge of how poplar leaf litter decomposes under Mediterranean marginal conditions can help to minimize fertilization inputs and determine the profitability and sustainability of energy crops established in these particularly sensitive areas for bioenergy. Leaf litter decomposition was monitored for 32 months using the litterbag technique in a poplar crop under short rotation conditions in a marginal Mediterranean area. In addition, nutrient dynamics, together with the production and composition of the woody and foliar biomass produced, were studied for a period of four years. Leaf litter decomposition was relatively slow, particularly during the winter months, and accelerated in early spring, coinciding with the rainy season. At the end of the decomposition study 50% of the initial litterfall was decomposed, releasing roughly 60% of the N, 40% of the K, and 70% of the P initially present in fresh leaves. Annual yields of 6.0 dry Mg ha−1 were obtained. The aerial biomass produced the first year of the second rotation cycle extracted 83, 8.7, and 29 kg ha−1 of N, P, and K, respectively, whereas the amount of nutrients that were estimated to be naturally supplied to the system through leaf litter decomposition were 180 kg ha−1 of N, 19 kg ha−1 of P, and 30 kg ha−1 of K. Therefore, four years after establishing the energy crop, leaf litter was able to release higher amounts of primary macronutrients into the environment than the nutrient uptake by the produced aboveground biomass (woody and foliar biomass). [ABSTRACT FROM AUTHOR]

The authors of this study evaluated the potential benefit on visual performance of a novel 3 week visual rehabilitation program based on the use of Gabor patches in patients undergoing bilateral cataract surgery with the implantation of two models of trifocal diffractive intraocular lens (IOL). A total of 30 patients were randomly assigned to two groups: a study group (15 patients) that used a videogame based on Gabor patches and a placebo group (15 patients) that used a videogame without specific stimuli for improving visual performance. No statistically significant differences between groups were found in distance, intermediate, and near post-training visual acuity (p ≥ 0.15). Significantly better distance contrast sensitivity (CS) was found for the spatial frequencies of 6 (p = 0.02) and 12 cpd (p = 0.01) in the study group. Likewise, significantly better values of near CS were found in the study group compared to the placebo group for the spatial frequency of 1.5 cpd (p = 0.02). In conclusion, a 3 week visual rehabilitation program based on the use of Gabor patches in the immediate postoperative period after the bilateral implantation of trifocal diffractive IOLs seems to be beneficial for improving both distance and near visual performance achieved with the implant. [ABSTRACT FROM AUTHOR]

A novel calcium carbonate cement system that mimics the naturally occurring mineralization process of carbon dioxide to biogenic or geologic calcium carbonate deposits was developed utilizing carbon dioxide-containing flue gas and high-calcium industrial solid waste as raw materials. The calcium carbonate cement reaction is based on the polymorphic transformation from metastable vaterite to aragonite and can achieve >40 MPa compressive strength. Due to its unique properties, the calcium carbonate cement is well suited for building materials applications with controlled factory manufacturing processes that can take advantage of its rapid curing at elevated temperatures and lower density for competitive advantages. Examples of suitable applications are lightweight fiber cement board and aerated concrete. The new cement system described is an environmentally sustainable alternative cement that can be carbon negative, meaning more carbon dioxide is captured during its manufacture than is emitted. [ABSTRACT FROM AUTHOR]

Simple Summary: The surplus of crude glycerin and the rising cost of feedstuffs have encouraged the nutritional valorization of this by-product as an interesting alternative ingredient in pig feed. We tested the addition of 2.5 and 5% glycerin to pelleted piglet diets to assess the effects on growth performance and digestibility of weaned piglets and to determine the serum concentrations of hormones related to energy metabolism and feed intake. Crude glycerin was included as a replacement for sheep sweet whey and wheat in pre-starter and starter diets, respectively. Growth data and fecal samples were collected at the end of each feeding phase. At the end of the study, blood samples were taken to analyze insulin and ghrelin concentrations. Over the whole period, our results showed that the average daily gain and the feed conversion ratio were not affected negatively by the dietary glycerin inclusion. There were also no differences between dietary treatments in terms of blood metabolites measured while the digestibility coefficients of dry and organic matter improved as glycerin increased. Therefore, crude glycerin could be used as an energy source to replace sweet whey and wheat and be added to pre-starter and starter diets. The aim of this study was to evaluate the effect of the inclusion of crude glycerin in post-weaning diets for piglets on growth performance and digestibility. The study was carried out with a total of 360 piglets over a 39 day period. Animals were blocked by body weight (7.7 ± 0.86 kg) and allotted randomly to one of three dietary treatments containing 0, 2.5 or 5% glycerin (G0, G2.5 and G5, respectively). Considering the whole period, glycerin did not affect the average daily gain. However, the average daily feed intake (ADFI) and the feed conversion ratio (FCR) tended to decrease or decreased linearly as the amount of glycerin increased, respectively (p = 0.060 and p = 0.039). The apparent total tract digestibility (ATTD) of dry and organic matter (DM, OM) increased linearly with increasing glycerin in both periods (p ≤ 0.05). At the end of the study, there were no differences between treatments for any of the hormones measured. In conclusion, the FCR and digestibility of DM and OM were improved although the ADFI tended to be lower when glycerin was included at 5%. Consequently, crude glycerin could be used as an alternative ingredient to partially replace sweet whey and wheat in post-weaning diets. [ABSTRACT FROM AUTHOR]

Postmortem studies are crucial for providing insight into emergent diseases. However, a complete autopsy is frequently not feasible in highly transmissible diseases due to biohazard challenges. Minimally invasive autopsy (MIA) is a needle-based approach aimed at collecting samples of key organs without opening the body, which may be a valid alternative in these cases. We aimed to: (a) provide biosafety guidelines for conducting MIAs in COVID-19 cases, (b) compare the performance of MIA versus complete autopsy, and (c) evaluate the safety of the procedure. Between October and December 2020, MIAs were conducted in six deceased patients with PCR-confirmed COVID-19, in a basic autopsy room, with reinforced personal protective equipment. Samples from the lungs and key organs were successfully obtained in all cases. A complete autopsy was performed on the same body immediately after the MIA. The diagnoses of the MIA matched those of the complete autopsy. In four patients, COVID-19 was the main cause of death, being responsible for the different stages of diffuse alveolar damage. No COVID-19 infection was detected in the personnel performing the MIAs or complete autopsies. In conclusion, MIA might be a feasible, adequate and safe alternative for cause of death investigation in COVID-19 cases. [ABSTRACT FROM AUTHOR]

In the present work, zinc titanates (ZTO) as photocatalysts were synthesized, characterized, and evaluated aiming to study their photocatalytic properties for hydrogen production under visible-light irradiation and employing MeOH (methanol) and TEOA (Triethanolamine) as sacrificial agents. ZTO were synthesized by modified Pechini method. Characterization of materials consisted in TGA, XRD, TEM, EELS, BET, and UV–Vis. Surface interaction studies consisted of FT-IR spectroscopy and determination of MeOH and TEOA adsorption–desorption capacities on the ZTO by TGA. Zinc titanates were evaluated as photocatalyst for H2 production using an artificial visible light and monitored by GC. TGA results led to establish calcination temperatures of 550 °C (Zn2Ti3O8) and 700 °C (ZnTiO3) to reach their crystalline phases. XRD analysis of sample cds-ZTO found cubic Zn2Ti3O8 and traces of the ZnO crystalline phase, while p-ZTO exhibited a mixture of cubic and hexagonal ZnTiO3 crystalline phases. Surface area for cds-ZTO was 88 m2/g, while ZnTiO3 had 13 m2/g. Photocatalytic H2 production for cds-ZTO and p-ZTO using TEOA as sacrificial agent showed the highest photocatalytic activities generating 548 and 441 µmolH2/h.gcat. TEOA adsorption–desorption capacity was found superior on cds-ZTO and p-ZTO than that for MeOH on both samples. [ABSTRACT FROM AUTHOR]

Mosquito-borne viruses such as dengue (DENV), chikungunya (CHIKV), and Zika (ZIKV) have spread in recent decades. We aimed to assess seroprevalence of arboviral infections in pregnant women living in Cereté, Caribbean Colombia. In 2016 a cross-sectional facility-based sero-survey study was performed among pregnant women (N = 90). Most of them (66%) reported at least one symptom or sign compatible with arboviral infection over the previous 15 days. All screened women had a positive IgG for DENV, 89% for ZIKV, and 82% for CHIKV. One woman tested positive for ZIKV IgM. This study shows the high exposure among pregnant women to arboviruses in endemic areas, shown by the high seroprevalence of past arboviral infections. Given the evidence on the potential risks of these arboviral infections on pregnancy and infant outcomes, these results highlight the need for continuous epidemiological surveillance of arboviral diseases, particularly among those most of risk of their harmful consequences. [ABSTRACT FROM AUTHOR]

Cystic Fibrosis (CF) is caused by mutations in the CF Transmembrane conductance Regulator (CFTR), the only ATP-binding cassette (ABC) transporter functioning as a channel. Unique to CFTR is a regulatory domain which includes a highly conformationally dynamic region—the regulatory extension (RE). The first nucleotide-binding domain of CFTR contains another dynamic region—regulatory insertion (RI). Removal of RI rescues the trafficking defect of CFTR with F508del, the most common CF-causing mutation. Here we aimed to assess the impact of RE removal (with/without RI or genetic revertants) on F508del-CFTR trafficking and how CFTR modulator drugs VX-809/lumacaftor and VX-770/ivacaftor rescue these variants. We generated cell lines expressing ΔRE and ΔRI CFTR (with/without genetic revertants) and assessed CFTR expression, stability, plasma membrane levels, and channel activity. Our data demonstrated that ΔRI significantly enhanced rescue of F508del-CFTR by VX-809. While the presence of the RI seems to be precluding full rescue of F508del-CFTR processing by VX-809, this region appears essential to rescue its function by VX-770, suggesting some contradictory role in rescue of F508del-CFTR by these two modulators. This negative impact of RI removal on VX-770-stimulated currents on F508del-CFTR can be compensated by deletion of the RE which also leads to the stabilization of this mutant. Despite both regions being conformationally dynamic, RI precludes F508del-CFTR processing while RE affects mostly its stability and channel opening. [ABSTRACT FROM AUTHOR]

In solar thermal plants, the use of molten salt as a heat transfer fluid is an advantageous alternative, although it has some disadvantages such as the formation of salt plugs in the pipes due to possible stratification of the salt or its solidification. The aim of this study was to implement an electromagnetic acoustic transducer (EMAT) not only capable of identifying the position of the plug, but also of determining whether the plug blocks the entire conductive surface or, on the contrary, is partial, allowing the fluid to pass through a smaller section. The proposed transducer is intended to be minimally invasive, allowing it to be used in the same way as a temperature probe. To do so, it creates torsional waves in the pipe, which are then used for a combination of measurements: pulse-echo and attenuation of the acoustic waves. Two materials with different densities (silicone and cement) were used in the tests carried out, which made it possible to check that for a given size of blockage, it is possible to identify the type of material from which it is formed. [ABSTRACT FROM AUTHOR]