Search

Low-density polyethylene (LDPE) is among the most abundant synthetic plastics in the world, contributing significantly to the plastic waste accumulation problem. A variety of microorganisms, such as Cupriavidus necator H16, Pseudomonas putida LS46, and Pseudomonas chlororaphis PA2361, can form biofilms on the surface of LDPE polymers and cause damage to the exterior structure. However, the damage is not extensive and complete degradation has not been achieved. The changes in polymer structure were analyzed using Time-domain Nuclear Magnetic Resonance (TD-NMR), High-Temperature Size-Exclusion Chromatography (HT-SEC), Differential Scanning Calorimetry (DSC), and Gas Chromatography with a Flame Ionization Detector (GC-FID). Limited degradation of the LDPE powder was seen in the first 30 days of incubation with the bacteria. Degradation can be seen in the LDPE weight loss percentage, LDPE degradation products in the supernatant, and the decrease in the percentage of amorphous regions (from >47% to 40%). The changes in weight-average molar mass (Mw), number-average molar mass (Mn), and the dispersity ratio (Đ) indicate that the low-molar mass fractions of the LDPE were preferentially degraded. The results here confirmed that LDPE degradation is heavily dependent on the presence of amorphous content and that only the amorphous content was degraded via bacterial enzymatic action. [ABSTRACT FROM AUTHOR]

This paper presents research aimed at laboratory experiments on static and cyclic fatigue testing of low-density polyethylene (LDPE) recovered from post-consumer waste in order to develop a recycled product exhibiting satisfactory mechanical and thermo-mechanical properties. The results of the cyclic fatigue tests set up to 80% of the maximum load in static tensile testing demonstrated satisfactory functionality of the recycled material developed by using the injection molding process. There was no significant change in the tensile strength under static and cyclic fatigue tests. Under cyclic loading, there was a quasi-static effect manifested by plastic deformation, and the displacement increased significantly. The static and cyclic tensile tests indicated improvement in the mechanical performance of the recycled LDPE as compared to the virgin material, owing to the high quality of the regranulates. Fourier Transform Infrared Spectroscopy (FTIR) was conducted to analyze the functional groups in virgin and recycled LDPE samples. The analysis showed no significant change in the transmittance spectra. The thermal degradation performance was also analyzed by Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA). The results were quite similar for both virgin and recycled LDPE. [ABSTRACT FROM AUTHOR]

Hazardous chemicals are transported on rail and road networks. In the case of accidental spillage or terror attack, civilian and military first responders must approach the scene equipped with appropriate personal protective equipment. The plausible manufacturing of chemical protective polymer material, from photocatalyst anatase titanium dioxide (TiO2) doped low-density polyethylene (LDPE), for cost-effective durable lightweight protective garments against toxic chemicals such as 2-chloroethyl ethyl sulphide (CEES) was investigated. The photocatalytic effects on the physico-chemical properties, before and after ultraviolet (UV) light exposure were evaluated. TiO2 (0, 5, 10, 15% wt) doped LDPE films were extruded and characterized by SEM-EDX, TEM, tensile tester, DSC-TGA and permeation studies before and after exposure to UV light, respectively. Results revealed that tensile strength and thermal analysis showed an increasing shift, whilst CEES permeation times responded oppositely with a significant decrease from 127 min to 84 min due to the degradation of the polymer matrix for neat LDPE, before and after UV exposure. The TiO2-doped films showed an increasing shift in results obtained for physical properties as the doping concentration increased, before and after UV exposure. Relating to chemical properties, the trend was the inverse of the physical properties. The 15% TiO2-doped film showed improved permeation times only when the photocatalytic TiO2 was activated. However, 5% TiO2-doped film exceptionally maintained better permeation times before and after UV exposure demonstrating better resistance against CEES permeation. [ABSTRACT FROM AUTHOR]

In this study, a critical evaluation and the benefits of using a waste and a virgin polymer in an asphalt mixture are presented. The present paper is the result of a three-year research effort to find a suitable recyclate compatible with asphalt binder and setting reaction conditions in the preparation of asphalt mixtures with the mentioned recyclate. This suitable candidate was recycled low-density polyethylene (LDPE), which was produced by recycling old, worn-out bags and films. An amount of 6% of LDPE by the weight of the binder content was suggested as the best amount of the modifier. Physical tests, including penetration, softening point, and kinematic viscosity have been carried out to prove the effectiveness of the modification on the binder properties. The effectiveness of the blending process and the appropriate concentration of additives led to a homogeneous polymer-modified bitumen without any imperfections in the structure. After successful preparation under laboratory conditions, this paper describes the preparation of asphalt mixtures directly in an asphalt-mixing plant and the subsequent implementation of a verification section. The overall composition of prepared polymer-modified asphalt mixtures has been studied. An important result of this study is the preparation of the asphalt mixture with waste LDPE that meets all the technical requirements. Moreover, it has been proven that this type of waste PE is fully applicable in asphalt-mixing plants in Slovakia, with zero or minimal financial burden on construction companies to complete the construction of their production facilities. Using such a technology, we can reduce the amount of waste plastics that otherwise end up in landfill. [ABSTRACT FROM AUTHOR]

Low-density polyethylene (LDPE) has been widely used in various applications due to its flexibility, lightness, and low production cost. However, its massive use in disposable products has raised environmental concerns, prompting the search for more sustainable alternatives. This study aims to investigate the mechanical properties achievable in a composite material utilizing low-density polyethylene (LDPE), potato starch (PS), and cellulose microfibrils (MFCA) at loadings of 0.05%, 0.15%, and 0.30%. Initially, the cellulose acetate microfibrils (MFCA) were produced via an electrospinning process. Subsequently, a dispersive mixture of the aforementioned materials was created through the extrusion and pelletizing process to form pellets. These pellets were then molded by injection molding to produce test specimens in accordance with ASTM D 638, the standard for tensile strength testing. The evaluation of the properties was conducted through mechanical tensile tests (ASTM D638), hardness tests (ASTM D 2240), melt flow index (ASTM D1238), and scanning electron microscopy (SEM). This study determined the influence of cellulose acetate microfibril loadings below 0.3% as reinforcement within a thermoplastic LDPE matrix. It was demonstrated that these microfibrils, due to their length-to-diameter ratio, contribute to an enhancement in the mechanical properties. [ABSTRACT FROM AUTHOR]

Active food packaging incorporated with natural plant extracts as food preservatives, which will totally replace chemical preservatives gradually, are of major interest. Sequentially to our and other scientists' previous work, in this paper we present the results of a study on the development of a novel active food packaging film based on the incorporation of a natural-halloysite/carvacrol-extract nanohybrid with the commercially used low-density polyethylene. The corona-treatment procedure was employed to incorporate a natural preservative on to the optimum final film. Packaging films are formatted with and without incorporation of natural-halloysite/carvacrol-extract nanohybrid and are coated externally, directly or via corona-treatment, with carvacrol essential oil. Mechanical, physicochemical, and preservation tests indicated that the low-density polyethylene incorporated perfectly with a natural-halloysite/carvacrol-extract nanohybrid. The extra external coating of the film with pure carvacrol extract using the corona-treatment technique led to approximately 100% higher Young Modulus values, slightly decreased ultimate strength by 20%, and exhibited almost stable elongation at break properties. The water vapor and oxygen properties were increased by 45 and 43%, correspondingly, compared to those of pure low-density polyethylene film. Finally, the antioxidant activity of the corona-treated film increased by 28% compared to the untreated film coated with carvacrol because of the controlled release rate of the carvacrol. [ABSTRACT FROM AUTHOR]

The accumulation of microplastics (MPs) in the environment has been a bottleneck for scientific society. Several approaches have been described as possibilities for reducing MPs in aquatic and terrestrial ecosystems; however, most of them are not environmentally friendly. Filamentous fungi (Ff) cells are currently considered a promising solution as a treatment for MPs. Therefore, the present study reports the potential ability of Ff isolated from mangrove sediments to biodegrade low-density polyethylene MPs (LDPEMPs). Six Ff strains were grown in batch cultures for 28 days, and one of them, Aspergillus sp. (AQ3A), showed the most prominent profile to biodegrade polymeric compounds. After morphological and molecular analysis, all strains were identified as belonging to the genera Aspergillus (MQ1C, AQ2A and AQ3A), Penicillium (MQ1A), and Trichoderma (MQ1B and MQ2A). The strain Aspergillus sp. (AQ3A) showed the most promising results with a LDPEMPs reduction rate of 47% and biomass formation of 0.0890 g·mL−1. Complementary studies with Aspergillus sp. (AQ3A) using Fourier-transform infrared spectroscopy (FTIR) highlighted changes in the molecular structure of LDPEMPs. These results indicate that Ff can contribute to the biodegradation of LDPEMPs. However, other parameters, mainly associated with the enzymes that are involved in this biodegradation process, need to be explored. [ABSTRACT FROM AUTHOR]

To fulfil the European Green Deal targets and implement a circular economy, there is an urgent need to increase recycling rates of packaging materials. However, before recycled materials can be used in food contact applications, they must meet high safety standards. According to the European Food Safety Authority (EFSA), a worst-case scenario must be applied and unknown substances must be evaluated as being potentially genotoxic. The Ames test, which detects direct DNA-reactive effects, together with chromatographic analysis is very promising to complement risk assessment. This study aims to evaluate the effectiveness of functional barriers in ten different samples, including virgin and recycled LDPE foils. FT-IR analysis did not show major differences between virgin and recycled films. Light microscopy revealed differences in quality and an increased number of particles. GC-MS analysis detected and quantified 35 substances, including eight unknowns. Using a miniaturized version of the Ames test, four of ten samples tested positive in two individual migrates up to a dilution of 12.5%. All virgin LDPE materials tested negative; however, recycled material F showed an increased mutagenic activity, with an n-fold induction up to 28. Samples with functional barriers lowered migration and reduced mutagenicity. Nonetheless, further investigations are needed to identify possible sources of contamination. [ABSTRACT FROM AUTHOR]

The global problem of microplastics in the environment is "inspiring" scientists to find environmentally friendly and economically viable methods to remove these pollutants from the environment. Advanced oxidation processes are among the most promising methods. In this work, the potential of Fenton, photo-Fenton, and Fenton-like processes for the degradation of microplastics from low-density polyethylene (LDPE), polypropylene (PP), and poly(vinyl chloride) (PVC) in water suspensions was investigated. The influence of three parameters on the efficiency of the degradation process was tested: the pH of the medium (3–7), the mass of added iron (10–50 times less than the mass of microplastics), and the mass of added H2O2 (5–25 times more than the mass of added iron). The effectiveness of the treatment was monitored by FTIR-ATR spectroscopy. After 60-min treatments, the PP microparticles were found to be insensitive. In the Fenton treatment of PVC and the photo-Fenton treatment of LDPE and PVC, changes in the FTIR spectra related to the degradation of the microplastics were observed. In these three cases, the treatment parameters were optimized. It was found that a low pH (3) and a high iron mass (optimal values were 1/12 and 1/10 of the mass of the microplastics for LDPE and PVC, respectively) favored all three. The degradation of LDPE by the photo-Fenton treatment was favored by high H2O2 concentrations (25 times higher than the mass of iron), while these concentrations were significantly lower for PVC (11 and 15 times for the Fenton and photo-Fenton treatment, respectively), suggesting that scavenging activity occurs. [ABSTRACT FROM AUTHOR]

Due to the intensive search for new types of advanced polymer materials for targeted applications, this work offers insight into the properties of low-density polyethylene/hematite composites. The specific feature of this study lies in the use of elongated hematite particles of different shapes. Uniform ellipsoid-, peanut- and rod-shaped hematite particles were hydrothermally synthesized and incorporated into the polymer matrix of low-density polyethylene (LDPE). LDPE/hematite composites are prepared by melt mixing. Hematite particles are characterized by scanning electron microscopy (SEM) and powder X-ray diffraction (PXRD). The pure LDPE polymer and LDPE/hematite composites were studied by FT-IR and UV-Vis-NIR spectroscopy and by thermogravimetric analysis (TGA). The determination of the mechanical and barrier properties was also carried out. The obtained results indicate the influence of the elongated particles on the improvement of LDPE properties. An increase in thermal stability and UV-absorption was observed as well as the improvement of mechanical and barrier properties. The improvement of the composites' properties in comparison to the pure LDPE is especially visible in the composites prepared with low content of hematite (0.25%). LDPE/hematite composites have promising characteristics for application as packaging materials with enhanced mechanical, thermal and barrier properties as well as UV-protective materials. [ABSTRACT FROM AUTHOR]

Τhe replacement of food packaging additives and preservatives with bio-based antioxidant/antibacterial compounds has been a common practice in recent years following the trend of bioeconomy and nanotechnology. Such bio-additives are often enclosed in nanocarriers for a controlled release process. Following this trend in this work, a thymol (TO)-rich activated carbon (AC) nanohybrid was prepared and characterized physicochemically with various techniques. This TO@AC nanohybrid, along with the pure activated carbon, was extruded with low-density polyethylene (LDPE) to develop novel active packaging films. The codenames used in this paper were LDPE/xTO@AC and LDPE/xAC for the nanohybrid and the pure activated carbon, respectively. X-ray diffractometry, Fourier-transform infrared spectroscopy, and scanning electron microscopy measurements showed high dispersity of both the TO@AC nanohybrid and the pure AC in the LDPE matrix, resulting in enhanced mechanical properties. The active film with 15 wt.% of the TO@AC nanohybrid (LDPE/15TO@AC) exhibited a 230% higher water/vapor barrier and 1928% lower oxygen permeability than the pure LDPE film. For this active film, the highest antioxidant activity referred to the DPPH assay (44.4%), the lowest thymol release rate (k2 ≈ 1.5 s−1), and the highest antibacterial activity were recorded, resulting in a 2-day extension of fresh pork fillets' shelf-life. [ABSTRACT FROM AUTHOR]

Paraffin phase change materials (PCMs) exhibit great potential in battery thermal management (BTM); nevertheless, their application has been hampered by the handicap of low thermal conductivity, leakage, and volume expansion during phase transition. In this work, ternary composite PCMs formed of paraffin, expanded graphite (EG), and low-density polyethylene (LDPE) were developed for application in BTM. The structure and properties of the composite PCMs were characterized via X-ray diffraction, scanning electron microscopy, differential scanning calorimetry, and thermal constant analysis. The result shows that EG can form a large-size graphite frame as heat conduction paths to improve the thermal conductivity of the composite PCM, and LDPE can form an interpenetrating network within the composite PCM to resist the internal stress of paraffin expansion and prevent deformation. The latent heat and thermal conductivity of the composite PCMs loaded with 10 wt% EG and 4 wt% LDPE can reach 172.06 J/g and 3.85 Wm−1K−1 with a relatively low leakage ratio of 6.2 wt%. Remarkably, the composite PCMs could reduce the temperature rise of the battery by 55.1%. In brief, this work provides a feasible route to develop high-performance PCMs for BTM. [ABSTRACT FROM AUTHOR]

The rheological behaviors of low-density polyethylene doped with additives (PEDA) determine the dynamic extrusion molding and structure of high-voltage cable insulation. However, the coupling effect of additives and molecular chain structure of LDPE on the rheological behaviors of PEDA is still unclear. Here, for the first time, the rheological behaviors of PEDA under uncross-linked conditions are revealed by experiment and simulation analysis, as well as rheology models. The rheology experiment and molecular simulation results indicate that additives can reduce the shear viscosity of PEDA, but the effect degree of different additives on rheological behaviors is determined by both chemical composition and topological structure. Combined with experiment analysis and the Doi–Edwards model, it demonstrates that the zero-shear viscosity is only determined by LDPE molecular chain structure. Nevertheless, different molecular chain structures of LDPE have different coupling effects with additives on the shear viscosity and non-Newtonian feature. Given this, the rheological behaviors of PEDA are predominant by the molecular chain structure of LDPE and are also affected by additives. This work can provide an important theoretical basis for the optimization and regulation of rheological behaviors of PEDA materials used for high-voltage cable insulation. [ABSTRACT FROM AUTHOR]

In the present work, direct incorporation of bioactive compounds onto the surface and interlayer of nanoclays before their incorporation into the final polymeric film was conducted, based on a green methodology developed by our group that is compatible with food packaging. This will lead to the higher thermal stability and the significant reduction of the loss of activity of the active ingredients during packaging configuration. On this basis, the essential oil (EO) components carvacrol (C), thymol (T) as well as olive leaf extract (OLE), which is used for the first time, were incorporated onto organo-modified montmorillonite (O) or inorganic bentonite (B) through the evaporation/adsorption method. The prepared bioactive nanocarriers were further mixed with low-density polyethylene (LDPE), via melt compounding, in order to prepare films for potential use as fresh fruit and vegetable packaging material. Characterization of the bioactive nanocarriers and films were performed through XRD, TGA, tensile, antimicrobial and antioxidant tests. Films with organically modified montmorillonite loaded with carvacrol (OC), thymol (OT) and olive leaf extract (OOLE) at 5% wt. showed better results in terms of mechanical properties. The films with polyethylene and organically modified montmorillonite loaded with carvacrol or thymol at 20% wt. (PE_OC20 and PE_OT20), as well as with olive leaf extract at 5 or 10 %wt., clay:bioactive substance ratio 1:0.5 and 10% compatibilizer (PE_OOLE5_MA10 and PE_OOLE10_MA10) exhibited the highest antioxidant activity. The resulting films displayed outstanding antimicrobial properties against Gram-negative Escherichia coli (E. coli) with the best results appearing in the films with 10% OC and OT. [ABSTRACT FROM AUTHOR]

An interfacial adhesion improvement between low-density polyethylene (LDPE) and aluminum (Al) foil is an important challenge in designing multilayered packaging (TetraPak packaging type) due to insufficient inherent adhesion between both untreated materials. Therefore, extra adhesive layers are often used. The hydrophobic character of LDPE is responsible for poor adhesion to Al and can result in delamination. This study deals with the comparative study of the bulk modification of LDPE with various commercially available adhesive promoters with different chemical compositions to increase LDPE's adhesive characteristics and ensure good adhesion in LDPE/Al laminates. A copolymer of ethylene and methacrylic acid; a terpolymer of ethylene, maleic anhydride, and acrylic ester; or maleated polyethylene (PE) were used as adhesive promoters, and their effect on adhesion improvement of LDPE to Al was investigated. The best adhesion improvement was observed in LDPE-modified samples with maleated PE, while 0.1 wt.% additive content significantly increased peel resistance (from zero to 105 N/m). An additional increase in additive content (0.5 wt.%) in LDPE led to stronger adhesion forces than the cohesion forces in Al foil. Adding 0.5 wt.% of maleated PE into LDPE improved the LDPE/Al laminates' adhesion and can be applied in multilayered lamination applications. [ABSTRACT FROM AUTHOR]

Sustainability, the circular economy, and the "greenhouse" effect have led the food packaging industry to use naturally available bio-compounds. The integration of such compounds in packaging films increases food safety and extends food shelf-life. The development of an active/antioxidant packaging film based on the widely commercially used low-density polyethylene, natural zeolite, and Thymol, a natural extract from thyme oil, is presented in this work. The obtained active films were characterized using X-Ray Diffraction, Fourier-Transform Infrared Spectroscopy, Scanning Electron Microscopy, and Differential Scanning Calorimetry techniques. The tensile strength, water–oxygen barrier properties, and total antioxidant activity were measured. Low-density polyethylene incorporated with Thymol@Natural Zeolite at a proportion of 15 wt% was the most promising material and was used as film to wrap-up pork fillets. The thiobarbituric acid (TBA) method and heme iron measurements indicated a delayed lipids oxidation using this film. A linear correlation between the TBA method and heme iron values seems to be established, which could result in a fast method to determine the degree of lipid oxidation in pork fillets. Finally, a two-stage diffusion process during Thymol release was observed, and the values of the diffusion coefficient was 2.09 × 10−7 and 1.21 × 10−8 cm2/s for each stage. The applied pseudo-second sorption model provided a rate constant k2 = 0.01647 (s−1). These results indicate the strong potential of such films to be used as food packaging materials free of E-number preservatives. [ABSTRACT FROM AUTHOR]

The rheological properties and processability at injection molding were studied for bisphenol-A polycarbonate (PC) that was modified by low-density polyethylene (LDPE) having a low shear viscosity. The LDPE addition significantly decreased the steady-state shear viscosity, especially in the high shear rate region. The decrease did not originate from slippage on the die wall but due to interfacial slippage between the PC and dispersed LDPE droplets that deformed to the flow direction to a great extent. As a result of the viscosity decrease, injection pressure largely decreased from 150 to 110 MPa with the addition only 5 wt.% of LDPE. The enhanced flowability also reduced the warpage of the molded product significantly, demonstrating that the processability at injection molding was improved by the addition of LDPE. [ABSTRACT FROM AUTHOR]

There is an increasing need to develop new polymer composites with improved properties compared to conventional pure polymer materials. This work aims to develop composites of low-density polyethylene (LDPE) and iron oxide hematite particles. For this purpose, different types of hematite particles with well-defined shapes and narrow size distributions were synthesized: HC2 sample with pseudocubic hematite particles of an average diameter of 1020 nm, HE1 sample with ellipsoidal hematite particles of an average diameter of 533 nm, and HS1 sample with spherical hematite particles of an average diameter of 168 nm. The mass fractions of hematite in the composites were 0.25%, 0.5%, and 1%. Prepared LDPE/hematite composites were characterized by thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), and diffuse reflectance ultraviolet-visible-near infrared (UV-Vis-NIR) spectroscopy. The mechanical and barrier properties were also studied. The obtained results showed that all prepared composites have improved properties compared to the pure LDPE, especially the composites with pseudocubic hematite particles of well-defined shapes. The results of this study indicate that LDPE/hematite composites can be promising materials for a wide range of applications, especially as packaging materials where improved thermal and mechanical properties as well as resistance to ultraviolet (UV) irradiation are required. [ABSTRACT FROM AUTHOR]

A new era is rising in food packaging and preservation, with a consequent focus on transition to "greener" and environmentally friendly techniques. The environmental problems that are emerging nowadays impose use of natural materials for food packaging applications, replacement of chemical preservatives with natural organic extractions, such as essential oils, and targeting of new achievements, such as further extension of food shelf-life. According to this new philosophy, most of the used materials for food packaging should be recyclable, natural or bio-based, and/or edible. The aim of this work was to investigate use and efficiency of a novel food packaging developed based on commercial LDPE polymer incorporated with natural material halloysite impregnated with natural extract of thyme oil. Moreover, a direct correlation between the stiff TBARS method and the easiest heme iron measurements method was scanned to test food lesions easier and faster. The result of this study was development of the LDPE/10TO@HNT film, which contains the optimum amount of a hybrid nanostructure and is capable to be used as an efficient active food packaging film. Furthermore, a linear correlation seems to connect the TBARS and heme iron measurements. [ABSTRACT FROM AUTHOR]

It is of significant concern that the buildup of non-biodegradable plastic waste in the environment may result in long-term issues with the environment, the economy and waste management. In this study, low-density polyethylene (LDPE) was compounded with different contents of poly(butylene succinate) (PBS) at 10–50 wt.%, to evaluate the potential of replacing commercial plastics with a biodegradable renewable polymer, PBS for packaging applications. The morphological, mechanical and thermal properties of the LDPE/PBS blends were examined in relation to the effect of polyethylene–graft–maleic anhydride (PE–g–MA) as a compatibilizer. LDPE/PBS/PE–g–MA blends were fabricated via the melt blending method using an internal mixer and then were compression molded into test samples. The presence of LDPE, PBS and PE–g–MA individually in the matrix for each blend presented physical interaction between the constituents, as shown by Fourier-transform infrared spectroscopy (FTIR). The morphology of LDPE/PBS/PE–g–MA blends showed improved compatibility and homogeneity between the LDPE matrix and PBS phase. Compatibilized LDPE/PBS blends showed an improvement in the tensile strength, with 5 phr of compatibilizer providing the optimal content. The thermal stability of LDPE/PBS blends decreased with higher PBS content and the thermal stability of compatibilized blends was higher in contrast to the uncompatibilized blends. Therefore, our research demonstrated that the partial substitution of LDPE with a biodegradable PBS and the incorporation of the PE–g–MA compatibilizer could develop an innovative blend with improved structural, mechanical and thermal properties. [ABSTRACT FROM AUTHOR]

When designing products that are made of composite materials and that contain natural fillers, it is particularly important to consider the long-term exposure of these materials to caustic liquids and substances (concentrated acids, bases), and to ensure that these products meet strict requirements for reliability and operational safety. This study investigated the effects of different solvents on the mass, mechanical, thermal, surface, and structural properties of polymer composites containing natural fillers in the form of pumpkin seed hulls. Experiments were conducted using four different filler contents (5, 10, 15, and 20 wt%) and grain sizes ranging from 0.2 to 0.4 mm and 0.6 to 0.8 mm. Hybrid injection-moulded pieces were immersed in distilled water (H2O), 1% NaOH solution, acetone (C3H6O), and toluene (C7H8) for 84 days. After that, their mechanical and thermal properties as well as their structure geometries were analysed statistically. Changes in the properties of the tested composite materials were assessed depending on the solvent type, and the statistical significance of these changes were determined. The results showed that the nature of degradation depended on the applied solvent type. It was observed that the polymer matrix of the toluene-immersed samples absorbed the liquid to a significant extent first and then underwent a gradual degradation with time. In contrast, the samples immersed in water showed a slight increase in their mass. It was found that all tested properties of the composite samples deteriorated irrespective of the solvent type. [ABSTRACT FROM AUTHOR]

Despite the enormous environmental damage caused by plastic waste, it makes up over one-third of globally produced plastics. Polyethylene (PE) wastes have low recycling but high production rates. Towards the construction of ionic solar cells from PE, the present work describes the loading of a bioactive photoacid phycocyanobilin (PCB) dye from the pigment of Spirulina blue–green algae (as a natural resource) on low-density polyethylene (LDPE) plastic film. Dyeing was confirmed by X-ray photoelectron spectroscopy (XPS). Upon excitation of the Soret-band (400 nm), the photoluminescence (PL) spectra of PCB in neat solvents revealed two prominent emission peaks at 450–550 and 600–700 nm. The first band assigned to bilirubin-like (PCBBR) species predominated the spectral profile in the highly rigid solvent glycerol and upon loading 0.45 % (w/w) of the dye on plastic. The photoluminescence excitation (PLE) spectra of PCB for the second region (Q-band) at 672 nm in the same solvents confirmed the ground state heterogenicity previously associated with the presence of PCBA (neutral), PCBB (cationic), and PCBC (anionic) conformers. Time-resolved photoluminescence (TRPL) measurements induced via excitation of all PCB species at 510 nm in methanol revealed three-lifetime components with τ1 = ~0.1 ns and τ2 = ~2 ns associated with PCBBR species and τ3 = ~5 ns pertinent to the long-living photoproduct X*. Decay-associated spectra (DAS) analysis of the photoluminescence transient spectra of the final dyed films in the solid-state confirmed the improved generation of the long-living photoproduct as manifested in a significant increase in the PL intensity (~100-fold) and lifetime value (~90 ns) in the Q-region upon loading 6.92 % (w/w) of the dye on plastic. The photoproduct species were presumably assigned to the deprotonated PCB species, suggesting improved ionic mobility. The potential implementation of the PCB-sensitized PE solid wastes for the fabrication of ionic solar cells is discussed. [ABSTRACT FROM AUTHOR]

Graphite lacquer was simply sprayed on glass and low-density polyethylene (LDPE) substrates to obtain large area films. Scanning Electron Microscopy (SEM) images, Raman spectra, X Ray Diffraction (XRD) spectra and current-voltage characteristics show that at room temperature, the as-deposited films on different substrates have similar morphological, structural and electrical properties. The morphological characterization reveals that the films are made of overlapped graphite platelets (GP), each composed of nanoplatelets with average sizes of a few tens of nanometers and about forty graphene layers. The thermoresistive properties of the GP films deposited on the different substrates and investigated in the temperature range from 20 to 120 °C show very different behaviors. For glass substrate, the resistance of the film decreases monotonically as a function of temperature by 7%; for LDPE substrate, the film resistance firstly increases more than one order of magnitude in the 20–100 °C range, then suddenly decreases to a temperature between 105 and 115 °C. These trends are related to the thermal expansion properties of the substrates and, for LDPE, also to the phase transitions occurring in the investigated temperature range, as evidenced by differential scanning calorimetry measurements. [ABSTRACT FROM AUTHOR]

The excessive amount of global plastic produced over the past century, together with poor waste management, has raised concerns about environmental sustainability. Plastic recycling has become a practical approach for diminishing plastic waste and maintaining sustainability among plastic waste management methods. Chemical and mechanical recycling are the typical approaches to recycling plastic waste, with a simple process, low cost, environmentally friendly process, and potential profitability. Several plastic materials, such as polypropylene, polystyrene, polyvinyl chloride, high-density polyethylene, low-density polyethylene, and polyurethanes, can be recycled with chemical and mechanical recycling approaches. Nevertheless, due to plastic waste's varying physical and chemical properties, plastic waste separation becomes a challenge. Hence, a reliable and effective plastic waste separation technology is critical for increasing plastic waste's value and recycling rate. Integrating recycling and plastic waste separation technologies would be an efficient method for reducing the accumulation of environmental contaminants produced by plastic waste, especially in industrial uses. This review addresses recent advances in plastic waste recycling technology, mainly with chemical recycling. The article also discusses the current recycling technology for various plastic materials. [ABSTRACT FROM AUTHOR]

Lignin was chemically modified with oligomeric polyethylene (oPE) to form oPE-grafted lignin (oPE-g-lignin) via lignin surface acylation and a radical coupling reaction with oPE. Then, pristine lignin and oPE-g-lignin were successfully compounded with low-density polyethylene (LDPE) through a typical compounding technique. Due to the oligomeric polyethylene chains grafted to the lignin's surface, the interfacial adhesion between the lignin particles and the LDPE matrix was considerably better in the oPE-g-lignin/LDPE biocomposite than in the pristine-lignin/LDPE one. This demonstrated that oPE-g-lignin can serve as both a biodegradable reinforcing filler, which can be loaded with a higher lignin content at 50 wt-%, and a nucleating agent to increase the crystallization temperature and improve the tensile characteristics of its LDPE biocomposites. Moreover, the foamability of the lignin-reinforced LDPE biocomposites was studied in the presence of a chemical blowing agent (azodicarbonamide) with dicumyl peroxide; for an oPE-g-lignin content up to 20 wt-%, the cell size distribution was quite uniform, and the foam expansion ratios (17.69 ± 0.92) were similar to those of the neat LDPE foam (17.04 ± 0.44). [ABSTRACT FROM AUTHOR]

Nanocomposite polymer films are a very diverse research field due to their many applications. The search for low-cost, versatile methods, producing regulated properties of the final products, has thus become extremely relevant. We have previously reported a bulk-scale process, dispersing granulated metal oxide nanoparticles, of both unary and multi-component nature, in a low-density polyethylene (LDPE) polymer matrix, establishing a reference in the produced films' optical properties, due to the high degree of homogeneity and preservation of the primary particle size allowed by this method. In this work, unmodified, free-standing particles, namely zinc oxide ( Z n O ), titanium dioxide ( T i O 2 ), aluminum oxide ( A l 2 O 3 ), and silicon dioxide ( S i O 2 ) are blended directly with LDPE, and the optical properties of the fabricated films are compared to those of films made using the granulation process. The direct blending process evidently allows for control of the secondary particle size and ensures a homogeneous dispersion of the particles, albeit to a lesser extent than the granulation process. Despite the secondary particle size being comparatively larger than its granulated counterpart, the process still provides a regulated degree of deagglomeration of the free-standing oxide particles, so it can be used as a low-cost alternative. The regulation of the secondary particle size tunes the transmission and reflection spectra, in both unary and mixed oxide compositions. Finally, the direct blending process exhibits a clear ability to tune the energy band gap in mixed oxides. [ABSTRACT FROM AUTHOR]

Melt blending is an effective way to prepare new composite materials, but most polymers are incompatible. In order to reduce the interfacial tension and obtain fine and stable morphology with internal symmetric micro-textures, suitable compatibilizers should be added to the blend. The two immiscible polymers, low-density polyethylene (LDPE) and polystyrene (PS), were compatibilized by styrene/ethylene/butylene/styrene block copolymers grafted with maleic anhydride (SEBS-g-MAH) and organomontmorillonite (OMMT). The scanning electron microscope results indicated that the size of the PS phase decreased with increasing the content of SEBS-g-MAH. By introducing OMMT into LDPE/PS/SEBS-g-MAH composites, the compatibility of composites was further improved. The rheological analysis and Cole–Cole plot analysis indicated that the addition of SEBS-g-MAH and OMMT increased the interaction between the two phases. The tensile strength, elongation at break, and impact strength of the LDPE/PS/SEBS-g-MAH (70/30/7, wt%) composite increased by 64%, 255%, and 380%, respectively, compared with the LDPE/PS (70/30, wt%) composite. A small amount of OMMT could synergistically compatibilize the LDPE/PS composite with SEBS-g-MAH. After adding 0.3% OMMT into the LDPE/PS/SEBS-g-MAH system, the tensile strength, elongation at break, and impact strength of the composite were further increased to 18.57 MPa, 71.87%, and 33.28 kJ/m2, respectively. [ABSTRACT FROM AUTHOR]

Low-density polyethylene (LDPE) has excellent dielectric properties and is extensively used in electrical equipment. Hexagonal boron nitride (h-BN) is similar to a graphite-layered structure, and alumina fiber (Al2O3) has high-temperature resistance and a strong performance. Herein, we prepared Al2O3-h-BN/LDPE nanocomposites by using LDPE as the matrix material and h-BN and Al2O3 as the fillers. The influence of different doping contents and the mass ratio of Al2O3 and h-BN (1:1) to LDPE on the electrical properties and thermal conductivity of the nanocomposites was examined. The results showed that the suppression effect on space charge was the most obvious and average. The charge density was the lowest and had the minimum decay rate when the doping content was 2%. The breakdown strength of the film reached the maximum value of 340.1 kV/mm, which was 12.3% higher than that of the pure LDPE (302.8 kV/mm). The thermal diffusivity of the composite sample was also higher than that of the single h-BN-doped sample when the content of h-BN and Al2O3 was 7%. The thermal conductivity was 59.3% higher than that of the pure LDPE sample and 20% higher than that of h-BN/LDPE. [ABSTRACT FROM AUTHOR]

As a result of R&D, a measuring system for controlling the thickness of the HDPE/LDPE (high-density polyethylene/low-density polyethylene) polymer geomembrane was developed using automation equipment. The relevance of this work consists of the development of a domestic, relatively inexpensive system for controlling the thickness of the HDPE/LDPE polymer geomembrane in production conditions based on modern equipment for enterprise automation. The scientific novelty consists of the use of original design solutions in the development of hardware and software complex mechanisms that allow controlling the thickness of the HDPE/LDPE polymer geomembrane layers along the entire width of the shaft, excluding deformation of the film as a result of foreign bodies entering during extrusion, cuts, monitoring the quality of the film in real time, as well as the possibility of analyzing the measured parameters in the database of the automated system. [ABSTRACT FROM AUTHOR]

The transformation of fog at a non-visible water layer on a membrane of low-density polyethylene (LDPE) and ethylene-vinyl acetate (EVA) was evaluated. Nonionic surfactants of major demand in the polyolefin industry were studied. A kinetic study using a hot fog chamber showed that condensation is controlled by both the diffusion and permanency of the surfactant more than by the change of the surface energy developed by the wetting agents. The greatest permanency of the anti-fog effect of the LDPE/EVA surface was close to 3000 h. The contact angle results demonstrated the ability of the wetting agent to spread out to the surface. Complementarily, the migration of nonionic surfactants from the inside of the polymeric matrix to the surface was analyzed by Fourier transform infrared (FTIR) microscopy. Additionally, electrical measurement on the anti-fogging membrane at alternating currents and at a sweep frequency was proposed to test the conductivity and wetting ability of nonionic surfactants. We proved that the amphiphilic molecules had the ability to increase the conductivity in the polyolefin membrane. A correlation between the bulk electrical conductivity and the permanency of the fogging control on the LDPE/EVA coextruded film was found. [ABSTRACT FROM AUTHOR]

A bipolar charge transport model is employed to investigate the remarkable reduction in dc conductivity of low-density polyethylene (LDPE) based material filled with uncoated nanofillers (reported in the first part of this work). The effect of temperature on charge transport is considered and the model outcomes are compared with measured conduction currents. The simulations reveal that the contribution of charge carrier recombination to the total transport process becomes more significant at elevated temperatures. Among the effects caused by the presence of nanoparticles, a reduced charge injection at electrodes has been found as the most essential one. Possible mechanisms for charge injection at different temperatures are therefore discussed. [ABSTRACT FROM AUTHOR]

This work presents results of bulk conductivity and surface potential decay measurements on low-density polyethylene and its nanocomposites filled with uncoated MgO and Al2O3, with the aim to highlight the effect of the nanofillers on charge transport processes. Material samples at various filler contents, up to 9 wt %, were prepared in the form of thin films. The performed measurements show a significant impact of the nanofillers on reduction of material's direct current (dc) conductivity. The investigations thus focused on the nanocomposites having the lowest dc conductivity. Various mechanisms of charge generation and transport in solids, including space charge limited current, Poole-Frenkel effect and Schottky injection, were utilized for examining the experimental results. The mobilities of charge carriers were deduced from the measured surface potential decay characteristics and were found to be at least two times lower for the nanocomposites. The temperature dependencies of the mobilities were compared for different materials. [ABSTRACT FROM AUTHOR]

Cellulose woven (CW) was surface treated by means of hexadecyltrimethylammonium bromide surfactant (HTAB) in aqueous solution medium at elevated temperature. The parameters of the surface treatment that have been studied are HTAB concentration (0.2, 0.4, 0.6, 0.8 and 1.0 wt%) and treatment time (1, 2, 3, 4 and 5 h). The untreated and treated CW filled low-density polyethylene (LDPE) biocomposites were prepared via compression molding technique. The tensile testing results of LDPE/CW biocomposites demonstrated that the optimum HTAB concentration for treatment of CW in 1 h was 0.4 wt%, while the optimum treatment time at 0.4 wt% HTAB was 2 h. The SEM (scanning electron microscope) images indicated that there is no significant difference in the morphology of the untreated and treated CW; however the morphology of the LDPE/treated CW biocomposite showed better interfacial adhesion as compared with the untreated ones. The FTIR (Fourier transform infrared spectroscopy) spectra revealed that the presence of HTAB on the surface of treated CW and also revealed the existence of intermolecular interactions between LDPE and treated CW. In summary, HTAB could potentially be used as a treatment agent for modifying the surface of CW and consequently improved the tensile properties of LDPE/CW biocomposites. [ABSTRACT FROM AUTHOR]

When designing products that are made of composite materials and that contain natural fillers, it is particularly important to consider the long-term exposure of these materials to caustic liquids and substances (concentrated acids, bases), and to ensure that these products meet strict requirements for reliability and operational safety. This study investigated the effects of different solvents on the mass, mechanical, thermal, surface, and structural properties of polymer composites containing natural fillers in the form of pumpkin seed hulls. Experiments were conducted using four different filler contents (5, 10, 15, and 20 wt%) and grain sizes ranging from 0.2 to 0.4 mm and 0.6 to 0.8 mm. Hybrid injection-moulded pieces were immersed in distilled water (H 2 O), 1% NaOH solution, acetone (C 3 H 6 O), and toluene (C 7 H 8 ) for 84 days. After that, their mechanical and thermal properties as well as their structure geometries were analysed statistically. Changes in the properties of the tested composite materials were assessed depending on the solvent type, and the statistical significance of these changes were determined. The results showed that the nature of degradation depended on the applied solvent type. It was observed that the polymer matrix of the toluene-immersed samples absorbed the liquid to a significant extent first and then underwent a gradual degradation with time. In contrast, the samples immersed in water showed a slight increase in their mass. It was found that all tested properties of the composite samples deteriorated irrespective of the solvent type.

The recycling of end-of-life plastics is a problem, since small parts can be returned into circulation. The rest is burned, landfilled or recycled into low-quality heating oil by pyrolysis methods. The disadvantages of this method are the need to dispose the formed by-product, pyrolytic carbon, the poor quality of produced liquid fuel and the low productivity of the method associated with the periodicity of the process. In this work, methods of thermogravimetry and chromatography–mass spectrometry (GC-MS) have been used to study the co-pyrolysis products of low-density polyethylene (LDPE) and oxygen-containing substances at the pressures of 4–8 MPa and temperatures of 520–620 °C. Experiments have highlighted the conditions needed for producing of high-quality liquid fuel. Initial data have been prepared for the design of a continuous pyrolysis reactor to dispose polymer waste for the production of bio-oil which would be available to enter the petrochemical products market. [ABSTRACT FROM AUTHOR]