Search

To obtain new information about surface waves, it is proposed to use an underwater acoustic wave gauge, and an assessment of its effectiveness can be performed using a numerical simulation and field experiment. A new device, an underwater acoustic wave gauge named "Kalmar", was developed by the Institute of Applied Physics of the Russian Academy of Sciences for long-term, all-weather monitoring of wind waves. The instrument uses ultrasound to probe the water surface from underwater and can be used to verify remote sensing data. In this work, the capabilities of the device are tested and compared with ADCP data. Two independent methods for processing underwater acoustic wave gauge data are discussed and compared. One of them is completely new for acoustic measurements and is based on the analysis of the shape of the reflected acoustic pulse averaged over space and time. The other allows processing individual reflected pulses and calculating the time implementation of the distance to the water surface. It is shown that two independent methods of significant wave height retrieval from the acoustic wave gauge measurements are highly correlated. The "Kalmar" acoustic wave gauge and the RDI WH-600 acoustic Doppler current profiler operated simultaneously at the test site in Gelendzhik from 1 February to 10 February 2020. The significant wave heights measured by the two instruments are in good agreement. [ABSTRACT FROM AUTHOR]

This paper reports on the location of sources contributing to a point flux measurement in the southern taiga, Russia. The measurement tower is surrounded by a coniferous forest with a mean aerodynamically active height of 27 m (h). Aerodynamical parameters of the forest, such as displacement height d and aerodynamic roughness z 0 , derived from wind speed profile measurements for 2017–2019, were used to estimate the seasonal and daily behavior of the flux footprint. Two analytical footprint models driven by d and z0 were used to estimate the footprint for canopy sources. The Lagrangian simulation (LS) approach driven by flow statistics from measurements and modeling was used to estimate the footprint for ground-located sources. The Flux Footprint Prediction (FFP) tool for assessing canopy flux footprint applied as the option in the EddyPro v.7 software was inspected against analytical and LS methods. For model comparisons, two parameters from estimated footprint functions were used: the upwind distance (fetch) of the peak contribution in the measured flux (Xmax) and the fetch that contributed to 80% of the total flux (CF80). The study shows that Xmax varies slightly with season but relies on wind direction and time of day. All methods yield different Xmax values but fall in the same range (60–130 m, around 2–5 h); thus, they can estimate the maximum influence distance with similar confidence. The CF80 values provided by the FFP tool are significantly lower than the CF80 values from other methods. For instance, the FFP tool estimates a CF80 of about 200 m (7 h), whereas other methods estimate a range of 600–1100 m (25–40 h). The study emphasizes that estimating the ground source footprint requires either the LS method or more complex approaches based on Computational Fluid Dynamics (CFD) techniques. These findings have essential implications in interpreting eddy-flux measurements over the quasi-homogeneous forest. [ABSTRACT FROM AUTHOR]

The measurement of the CO2 concentration has a wide range of applications. Traditionally, it has been used to assess air quality, with other applications linked to the experimental assessment of occupancy patterns and air renewal rates. More recently, the worldwide dissemination of COVID-19 establishing a relationship between infection risk and the mean CO2 level has abruptly led to the measurement of the CO2 concentration in order to limit the spread of this respiratory disease in the indoor environment. Therefore, the extensive application of this measurement outside of traditional air quality assessment requires an in-depth analysis of the suitability of these sensors for such modern applications. This paper discusses the performance of an array of commercial wall-mounted CO2 sensors, focusing on their application to obtain occupancy patterns and air renovation rates. This study is supported by several long-term test campaigns conducted in an in-use office building located in south-eastern Spain. The results show a spread of 19–101 ppm, with a drift of 28 ppm over 5 years, an offset of 2–301 ppm and fluctuations up to 80 ppm in instantaneous measurements not related to concentration changes. It is proposed that values averaged over 30 min, using a suitable reference value, be used to avoid erroneous results when calibration is not feasible. [ABSTRACT FROM AUTHOR]

Ammonia and greenhouse gases have a negative impact on the environment. The most important agricultural sources of ammonia are dairy cattle housing systems, which are mainly naturally ventilated. Estimating emissions for naturally ventilated barns (NVB) is challenging due to the large number of influencing factors. Most notably, the direct coupling of the inside flow regime with ambient and turbulent weather conditions causes difficulties in measuring ventilation rates, gas concentrations and emissions; thus, different methods are available. In this study, we compared the outputs of total volume flow obtained by two indirect methods (CO 2 mass balance) to the direct method. The latter we assume in this study as the reference method since it is a fundamental approach that estimates airflow on the inlet. In the context of mass balancing, we compared wind related (sampling method 1) and non-wind related (sampling method 2) approaches for measuring CO 2 concentrations. The total volume flow calculations were based on hourly measurements of CO 2 concentrations obtained by Fourier transform infrared (FTIR) spectrometer. Data were collected over a period of six months. The values of the total volume flow were filtered for prevailing southern winds (90 ∘ angle). The wind related method (sampling method 1) in stable cross-inflow conditions produces more accurate and realistic values in terms of the general representation of the values in comparison with direct method and can be considered further for measurements of volume flow in the NVBs. [ABSTRACT FROM AUTHOR]

In recent years, black carbon (BC) has been gaining more attention due to the diversity of anthropogenic sources and the harmful effects on human health, environment, and climate. In this paper, for the first time in Poland, the results of long-term measurements of eBC concentrations (2009–2020) at the urban background station in Zabrze (southern Poland) are presented. A Multi-Angle Absorption Photometer (MAAP) was used, which enables the measurement of eBC concentration in fine particulate matter (PM2.5). The mean concentration of eBC over the 11-year period (3.82 μg·m−3) was higher compared to the values recorded at most European urban stations. Annual averaged eBC levels showed a downward trend and clear seasonal variations, which was caused mainly by changes in the intensity of anthropogenic emissions. The impact of meteorological parameters, in particular air temperature and wind speed, which determine the intensity of emissions and the conditions of pollutant dispersion, was not without significance. The work additionally attempts to assess the possible impact of remedial actions carried out in Zabrze over the last decade. The results showed that modernization in industry and heating and maintenance of green areas potentially had the most important impact on the decline in eBC concentrations. [ABSTRACT FROM AUTHOR]

This article presents the results of experimental research on energy consumption of a prefabricated lightweight passive house located in the south of Poland. The key design parameters of the building were as follows: orientation maximizing heat gains from solar radiation, high thermal insulation of partitions, heat provided by ground source heat pump, and mechanical ventilation system with the heat exchanger. The measurements were performed in normal operating conditions in an inhabited building, throughout the years 2011–2019. For the year 2012, the article also presents the detailed structure of electricity used for particular devices. The objective of the research was to verify whether, in the long term, the building fulfils the energy consumption requirements for passive buildings. The measurements showed that energy consumption for heating was 50% lower than the value required from passive buildings. However, primary energy consumption for the entire building was exceeded already in the second year of research. This was caused by two factors: human behaviors and the type of primary energy source. The research concludes that the maintenance of passive house standard is vulnerable to human impact and difficult in the case of power source characterized by high index of expenditure on non-renewable primary energy. The article also presents recommendations on how to restore the passive house standard in the building. [ABSTRACT FROM AUTHOR]