Search

Deploying Internet of Things (IoT) on low-power lossy wireless sensor/actuator networks (LLN) in harsh industrial environments presents challenges such as dynamic link qualities due to noise, signal attenuations and spurious interferences. However, the critical demand for industrial applications is reliability of data delivery on low-cost low-power sensor/actuator devices. To address these issues, this paper proposes a fully autonomous scheduling approach, called Auto-Sched, which ensures reliability of data delivery for both downlink and uplink traffic scheduling and enhances network robustness against node/link failures. To ensure reliability, Auto-Sched assigns retransmission time slots based on the reliability constraints of the communication link. To avoid collision issues, Auto-Sched creates an upward pipeline-like communication schedule for uplink end-to-end data delivery, and a downward pipeline-like communication schedule for downlink scheduling. For enhancing network robustness, we propose a simple algorithm for real-time autonomous schedule reconstruction, when node or link failures occur, with minimal influence on communication overhead. Performance evaluations quantified the performance of our proposed approaches under a variety of scenarios comparing them with existing approaches. [ABSTRACT FROM AUTHOR]

The links of low power wireless sensor networks are error prone and the transmission on a wireless link is determined probabilistically by the packet reception rate (PRR) of the link. On the other hand, there is a very strict requirement in the end-to-end reliability and delay of sensor data in industrial wireless sensor networks (IWSNs). The existing approaches to provide the end-to-end reliability in IWSNs is retransmitting the packet when failure occurs. These approaches transmit a packet multiple times in successive time slots to provide the required reliability. These approaches, however, can increase the average delay of packets and the number of packets buffered in a queue. This paper proposes a new scheme to estimate the probabilistic amount of packets, called queue level (QL), in the buffer of each node based on the PRRs of the wireless links. This paper also proposes a QL-based centralized scheduling algorithm to assign time slots efficiently in TDMA-based IWSNs. The proposed scheduling algorithm gives higher priority to the nodes with higher QL. By assigning time slots first to the node with the highest QL, we can reduce the average end-to-end delay of packets and reduce the amount of buffered packets in the queue while satisfying the required end-to-end reliability. The performance of the proposed scheduling algorithm have been evaluated through a simulation using the Cooja simulator and compared with the existing approach. In the simulation on an sample network with the target end-to-end reliability of 99%, all of the flows were shown to guarantee the target reliability in both algorithms: on average, 99.76% in the proposed algorithm and 99.85% in the existing approach. On the other hand, the proposed algorithm showed much better performance than the existing approach in terms of the average end-to-end delay of packets (about 47% less) and the number of maximally buffered packets in the queue of each node (maximally, more than 90% less). [ABSTRACT FROM AUTHOR]

Although mature industrial wireless sensor network applications increasingly require low-power operations, deterministic communications, and end-to-end reliability, it is very difficult to achieve these goals because of link burstiness and interference. In this paper, we propose a novel link quality estimation mechanism named the burstiness distribution metric, which uses the distribution of burstiness in the links to deal with variations in wireless link quality. First, we estimated the quality of the link at the receiver node by counting the number of consecutive packets lost in each link. Based on that, we created a burstiness distribution list and estimated the number of transmissions. Our simulation in the Cooja simulator from Contiki-NG showed that our proposal can be used in scheduling as an input metric to calculate the number of transmissions in order to achieve a reliability target in industrial wireless sensor networks. [ABSTRACT FROM AUTHOR]

Wireless sensor networks (WSN) are networks for gathering data from sensor nodes that have been applied in industry for a long time. In real-time industrial applications with tight latencies, schedulability is one of the most critical issues. Some authors have proposed centralized scheduling algorithms for time-slotted channel hopping (TSCH) networks for real-time applications in industry, however, they have some disadvantages such as schedulability and high data traffic. In this paper, we improve the schedulability, latency, data traffic by dynamically prioritizing packets which are based on number duplex-conflicts and dynamically combining the packets. As a result, we show that the packet-combining algorithm improves schedulability and minimizes the amount of traffic in a network when compared with existing approaches. [ABSTRACT FROM AUTHOR]

LoRa (Long Range) is a long-range communications capacity with chirp spread spectrum modulation. It has been developed for Internet of Things (IoT) applications for long-distance and low power consumption. Some authors proposed LoRa protocols such as LoRaWAN, LoRaBlink, DQ-LoRa and the multi-hop LoRa network with linear topology; however, these protocols have disadvantages. In this paper, we propose a minimized latency multi-hop LoRa network protocol that is collision-free with low latency to improve on the disadvantages. First, in the proposed protocol, tree topology is constructed by exchanging packets between LoRa nodes and the sink node. During this period, a timeslot and channel are assigned to each tree link, over which LoRa nodes communicate with their parent node and which is collision-free with its neighbor nodes. After the tree construction period, LoRa nodes start data transmission using the timeslot and channel that they have already been assigned to in the tree construction period. We developed the proposed protocol in a LoRa node prototype using the MultiTech mDot module, and we conducted experiments at Ulsan University. The results show that the proposed protocol provides high reliability, parallel transmissions, a minimized number of timeslots assigned for all the links in the network, a minimized packet size, and low latency. [ABSTRACT FROM AUTHOR]